Search

This work studies the self-heating (SH) effect in ultra-thin body ultra-thin buried oxide (UTBB) FDSOI MOSFETs at cryogenic temperatures down to 77 K. S-parameter measurements in a wide frequency range, with the so-called RF technique, are employed to assess SH parameters and related variation of analog figures of merit (FoMs) at different temperatures. Contrary to the expectations, the effect of self-heating on analog FoMs is slightly weaker at cryogenic temperatures with respect to room-temperature case. The extracted thermal resistance and channel temperature rise at 300 K and 77 K in short-channel devices are of the same order of magnitude. The observed increase in SH characteristic frequency with temperature reduction emphasizes the advantage of the RF technique for the fair analysis of SH-related features in advanced technologies at cryogenic temperatures.

This paper presents an experimental analysis of the analog characteristics of self-cascode structures composed by 28 nm technological node ultra-thin body and BOX fully-depleted silicon-on-insulator planar MOSFETs, focusing on the subthreshold operation regime. Apart from the increased gain promoted by the reduction of front gate voltage, there is further improvement when the back-gate bias is used to reduce the threshold voltage of transistor close to the drain of the composite device, making this structure a promising option for low-power low-voltage (LPLV) analog applications.

International audience; The negative bias temperature instability (NBTI) is investigated in ultrathin body ultrathin box (UTBB) fully depleted silicon-on-insulator (FD-SOI) p-MOSFETs with zero back gate bias and small drain bias voltage. The threshold voltage shifts during stress at different temperatures and gate bias voltage conditions show that the NBTI is dominated by the trapping of holes in preexisting traps of the gate dielectric, while the recovery transient follows a logarithmic-like time dependence. Considering the hole-trapping/detrapping mechanisms, NBTI modeling has been proposed capturing the temperature and gate voltage dependence.

A detailed study of the hot-carrier degradation in nano-scale fully depleted ultra-thin body and buried oxide n-MOSFETs is presented. The degradation mechanisms were identified based on static current-voltage measurements. The degradation of the transistor was explained by considering generation of traps at the gate dielectric/Si interface and traps located within a tunneling distance of the interface. All stress parameters are considered describing with semi-empirical relations their impact on the transistor parameters. Based on our analytical compact model, we propose an aging hot-carrier model predicting with good accuracy the device degradation stressed under different bias conditions using a unique set of model parameters. Display Omitted The hot-carrier degradation of nanoscale UTBB FD-SOI n-MOSFETs has been investigated under different drain and gate bias stress conditions.The degradation mechanisms have been identified by studying the static current-voltage characteristics measurements.The impact of the HC degradation on the device parameters has been expressed with semi-empirical models in terms of the stress time, channel length, drain bias and gate bias.Based on our analytical compact model, HC aging model is proposed enabling to predict the device degradation stressed under different bias conditions, using a unique set of few model parameters determined for each technology through measurements.

This work provides a detailed study of 28 nm fully-depleted silicon-on-insulator (FD-SOI) planar ultra-thin body and BOX (UTBB) MOSFETs for high frequency applications. All parasitic elements such as the parasitic gate and source/drain series resistances, total capacitances are extracted and their effects on RF performance are analyzed and compared with previous work on similar devices. Two main RF figures of merit (FoM) such as the current gain cut-off frequency ( f T ) and the maximum oscillation frequency ( f max ) are determined. It is shown that f T of ∼280 GHz and f max of ∼250 GHz are achievable in the shortest devices. Based on the extracted parameters, the validation of the small-signal equivalent circuit used for modeling UTBB MOSFETs is investigated by comparing simulated and measured S -parameters.

This work presents a detailed RF characterization of 28 FDSOI nMOSFETs at cryogenic temperatures down to 4.2 K. Two main RF Figures of Merit (FoMs), i.e. current gain cutoff frequency (f T ) and maximum oscillation frequency (f max ), as well as parasitic elements of the small-signal equivalent circuit are extracted from the measured S-parameters. The observed behavior of RF FoMs versus temperature is discussed in terms of small-signal equivalent circuit elements, both intrinsic and extrinsic (parasitics). This study suggests 28 FDSOI nMOSFETs as a good candidate for future cryogenic applications down to 4.2 K and clarifies the origin and limitations of the performance.

This work presents, for the first time to our best knowledge, RF characterization of 28 nm FDSOI CMOS process at cryogenic temperatures including extraction of parasitic elements of small-signal equivalent circuit and two main RF Figures of Merit (FoM), i.e. current cutoff frequency (fT) and maximum oscillation frequency (fmax). Increases of fT and fmax by about 85 GHz and 30 GHz, respectively, are demonstrated at cryogenic temperatures. The observed behavior of RF FoMs versus temperature is analyzed in terms of small-signal equivalent circuit elements. This study suggests 28 nm FDSOI as a good candidate for future cryogenic applications.

This work presents a detailed characterization of 28 nm FDSOI CMOS process at cryogenic temperatures. Electrostatic, Analog and RF Figures of Merit (FoM) are studied for the first time to our best knowledge. At cryogenic temperatures, 20–70% enhancement of drain current, Id, and maximum transconductance, gm_max, values as well as up to 100 GHz increase of cut-off frequency, fT, are demonstrated. Temperature behavior of analog and RF FoMs is discussed in terms of mobility and series resistance effect. This first study suggests 28FDSOI as a good contender for future read-out electronics around qubits.

The Drain Induced Barrier Lowering (DIBL) behavior in Ultra-Thin Body and Buried oxide (UTBB) transistors is investigated in details in the temperature range up to 150 °C, for the first time to the best of our knowledge. The analysis is based on experimental data, physical device simulation, compact model (SPICE) simulation and previously published models. Contrary to MASTAR prediction, experiments reveal DIBL increase with temperature. Physical device simulations of different thin-film fully-depleted (FD) devices outline the generality of such behavior. SPICE simulations, with UTSOI DK2.4 model, only partially adhere to experimental trends. Several analytic models available in the literature are assessed for DIBL vs. temperature prediction. Although being the closest to experiments, Fasarakis’ model overestimates DIBL(T) dependence for shortest devices and underestimates it for upsized gate lengths frequently used in ultra-low-voltage (ULV) applications. This model is improved in our work, by introducing a temperature-dependent inversion charge at threshold. The improved model shows very good agreement with experimental data, with high gain in precision for the gate lengths under test.

This paper describes a complete process/design co-optimization methodology based on Fully Depleted SOI (FDSOI) technology. A process optimization is detailed through significant effective capacitance reduction, in order to optimize jointly frequency/leakage ratio and high frequency performances. In this objective, an efficient and low cost offset-spacers morphology has been designed to achieve maximum performance benefits. Both digital, analog and RF performances are exposed, and compared to 28LP gate-first technology. We evidence that FDSOI brings energy efficiency digital and AMS/RF breakthrough for IoT.

International audience; The hot carrier (HC)-induced traps in nanoscale fully depleted ultrathin body and buried oxide nMOSFETs are investigated by low-frequency noise (LFN) measurements in the frequency and time domains. The measured noise spectra are composed of 1/f and Lorentzian-type components. The Lorentzian noise is due to either generation-recombination noise or random telegraph noise (RTN). Based on the LFN results, the effect of the HC stress on fully depleted silicon-on-insulator MOSFETs is investigated after short- and long-time stress. The capture and emission time constants responsible for the RTN noise were calculated as the average duration time of the high/low drain current state, respectively. Analysis of RTN traps detected in fresh and HC-stressed devices indicates that the RTN amplitude is uncorrelated to the trap time constants, i.e., the impact of the trap depth from the interface is masked by that of the trap location over the channel. The overall results lead to an analytical expression for the RTN amplitude, enabling to predict the RTN changes from the subthreshold to the above-threshold region.

We present a 65nm RF SOI CMOS technology, targeted as Low Power (LP) to serve mobile applications. The integration has been made on High Resistive (HR) back substrate 300mm SOI wafers from SOITEC to improve performances in high frequency range, compared to bulk [1, 2]. For the first time, low leakage SRAM (Isb< 10pA at 0.9V, 25{degree sign}C, for 0.62µm2 and 0.52µm2 cells) are integrated on these HR wafers, and the paper reports a 30% power reduction in operation for a given maximum speed, compared to similar SRAM design on bulk. Furthermore, we have demonstrated a 21% measured power-delay product reduction compared to bulk, at 125{degree sign}C, on loaded ring oscillators.

The Drain Induced Barrier Lowering (DIBL) behavior in Ultra-Thin Body and Buried oxide (UTBB) transistors is investigated in details in the temperature range up to 150°C, for the first time to the best of our knowledge. The analysis is based on experimental data, physical device simulation, compact model (SPICE) simulation and previously published models. Contrarily to MASTAR prediction, experiments reveal DIBL increase with temperature. Physical device simulations of different thin-film fully-depleted (FD) devices outline the generality of such behavior. SPICE simulations, with UTSOI DK2.4 model, only partially adhere to experimental trends. Several analytic models available in the literature are assessed for DIBL vs. temperature prediction. Although being the closest to experiments, Fasarakis' model overestimates DIBL(T) dependence for shortest devices and underestimates it for upsized gate lengths frequently used in ULV (ultra-low-voltage) applications. This model is improved in our work, by introducing a temperature-dependent inversion charge at threshold. The improved model showed very good agreement with experimental data, with high gain in precision for the gate lengths under test.

International audience; An analytical drain-current compact model for lightly doped short-channel ultrathin-body and box fully depleted silicon-on-insulator MOSFETs with back-gate control is presented. The model includes the effects of drain-induced barrier lowering, channel-length modulation, saturation velocity, mobility degradation, quantum confinement, velocity overshoot, and self-heating. The proposed model has been validated by comparing with the experimental transfer and output characteristics of devices with the channel lengths of 30 and 240 nm and with back bias varying from -3 to +3 V. The good accuracy of the model makes it suitable for implementation in circuit simulation tools.

This work presents a comparison of parasitic elements (capacitances and resistances) in a view of their effect on RF Figures of Merit (FoM) in 28 nm fully-depleted silicon-on-insulator (FD SOI) ultra-thin body and buried oxide (UTBB) MOSFETs and their Bulk counterparts. Complete set of small-signal equivalent circuit elements (both “intrinsic”, i.e. device related and “extrinsic”, i.e. parasitic) are extracted from S-parameters measurements in a frequency range up to 40 GHz. It is shown that detrimental/harmful effect of parasitics, particularly capacitances, is stronger in 28 nm bulk technology compared to 28 FD SOI.

session poster; International audience; A thorough investigation and statistical analysis of the low-frequency (LFN) and random telegraph noise (RTN) in 28 and 14nm FD-SOI CMOS transistors is presented, for the first time. It is shown that the 14nm technology node is improved in terms of threshold voltage fluctuations when compared to the 28nm one. A new analysis method that directly probes the RTN presence is also proposed. Finally, the LFN/RTN impact on the device dynamic variability is presented through CADENCE design suite circuit simulations.

This paper demonstrates the 28nm ultra-thin body and buried oxide (UTBB) FD-SOI high-density (0.120µm2) single p-well (SPW) bitcell architecture for the design of low-power wide voltage range systems enabled by back-bias adjustment. The results from a 140kb programmable dynamic SRAM characterization test module provide both information about location and cause of failures as well as power and performance by mimicking system operating conditions over a wide supply voltage range. A 410mV minimum operating voltage and less than 310mV data retention voltage with a leakage current close to 100fA/bitcell are measured. Improved bitcell read access time and write-ability through back-bias are demonstrated with less than 5% of stand-by power overhead.

This work provides a detailed study of 28 nm fully-depleted silicon-on-insulator (FD SOI) ultra-thin body and buried oxide (BOX) (UTBB) MOSFETs for high frequency applications. RF figures of merit (FoM), i.e. the current gain cut-off frequency (f T ) and the maximum oscillation frequency (f max ), are presented for different transistor geometries. The parasitic gate and source/drain series resistances, as well as capacitances and their effect on RF performance are analyzed.

session B8L-E: Variability and Reliability in advanced MOSFETs; International audience; The impact of the dynamic variability due to low frequency and RTS fluctuations on single MOSFET operation from 28nm FD-SOI technology is investigated for the first time. It is shown that, for small rise time of ramp gate voltage, the drain current characteristics I d (V g ) exhibit a huge sweep-to-sweep dispersion due to the low frequency noise. Such a single device dynamic variability, which scales as the reciprocal square root of device area, is added to the static mismatch contribution and could amount up to ≈30% of static variability sources.

Inter-die variability of analog figures of merit of ultra-thin body and buried oxide (UTBB) FDSOI MOSFETs was studied in a wide frequency range. We demonstrate that variability in the entire frequency range is small and does not exceed 5%, which is considerably less than in previously published results on SOI FinFETs. An effect of frequency on the analog figures of merit variability is discussed and preliminary explanation is proposed.

This work presents an in-depth wide-frequency band assessment of 28 nm FDSOI MOSFETs for analogue and RF applications. The focus is mainly on such figures of merit (FoM) as the transconductance g m , the output conductance g d , the intrinsic gain A v and the cut-off frequencies f t and f max . Firstly, 28 nm FDSOI MOSFETs are compared with other advanced devices and are shown to outperform them. Secondly, g m -A v analogue metrics is demonstrated to be affected by operation frequency. Small-signal parameters variation is limited and dominated by self-heating effect. This is in contrast to the first generation of ultra-thin body and BOX devices without a ground plane where coupling through the substrate has a considerable effect. Thirdly, the self-heating effect is analysed and shown to be smaller than previously predicted by simulations for such devices. Fourthly, it is shown that f t reaches ∼270 GHz in the shortest devices.

We designed an addressable transistors array to analyse local variability at the wafer scale. On FDSOI substrates, we measure no impact of the silicon thickness variations on short channel transistors, and demonstrate that the impact on large area transistors is no more visible when the Tsi is well controlled.

In this paper, we study how to boost the performance of FDSOI (Fully-Depleted Silicon On Insulator) devices with High-K and Single Metal gate by using the combination of Ultra-Thin Buried Oxide (UTBOX), Ground Plane (GP) and local back biasing integrated with our hybrid process. The interest of local back biasing is highlighted in term of threshold voltage VT modulation and power management study on the 45 nm 0.374 μm2 bitcells and on the ESD functionality as compared to bulk technology.

This work highlights the way to optimize the speed/power performance of the planar FDSOI technology at the 28nm node and beyond. The combination of gate length shrink and spacerO increase leads to 13% delay decrease and 15% dynamic power saving at same speed through capacitance reduction. It demonstrates that, as far as the access resistance penalty is kept reasonably low, increasing the spacerO is highly efficient to boost AC performance in FDSOI.

This paper presents an IEEE 802.11n Low-Density Parity-Check (LDPC) decoder implemented in 28nm Ultra-Thin Body and BOX Fully Depleted SOI (UTBB FDSOI), and demonstrates the performance gains of this circuit vs. 28nm LP high-κ metal-gate CMOS bulk technology. It also introduces extended body bias (BB) design techniques to take advantage of specific features of the UTBB technology to overcome the +/-300mV BB range limitation of conventional bulk technologies [1].

Unique features of the 28nm ultra-thin body and buried oxide (UTBB) FDSOI technology enable the operation of SRAM in a wide voltage range. Minimum operating voltage limitations of a high-density (HD) 6-transistor (6T) SRAM can be overcome by using a single p-well (SPW) bitcell design in FDSOI. Transient simulations of dynamic failure metrics suggest that a HD 6T SPW array with 128 cells per bitline operates down to 0.65V in typical conditions with no assist techniques. In addition, a wide back-bias voltage range enables run-time tradeoffs between the low leakage current in the sleep mode and the short access time in the active mode, making it attractive for high-performance portable applications.

International audience; Low-frequency (LF) noise was studied on 28 nm CMOS technology FDSOI devices with ultra-thin silicon film (7 nm) and thin buried oxide (25 nm). The noise level was observed to be strongly dependent on the combination of the front and back gate biasing voltages. This was explained by the coupling effect of both Si/High-K dielectric and Si/SiO 2 interface noise sources (channel/front oxide and channel/buried oxide), in combination with the variation of the Remote Coulomb scattering coefficient α. From comparison of the experimental and simulation results, it is illustrated that the main reason of this dependence is the distance between the charge distribution centroid and the interfaces, which is also controlled by both front and back-gate bias voltages, and the way this distance affects the Remote Coulomb scattering coefficient α. A new LF noise model approach is suggested to include the impact of all these parameters, and also allows us to extract the oxide trap density values for both interfaces.

International audience; Low-frequency (LF) noise has been studied on 28 nm FDSOI devices with ultra-thin silicon film (7 nm) and thin buried oxide (25 nm). A strong dependence of the noise level on the combination of the front and back biasing voltages was observed, and justified by the coupling effect of both Si/High-K dielectric and Si/SiO2 interface noise sources (channel/front oxide and channel/buried oxide), combined with the change of the Remote Coulomb scattering. From comparisons of the experimental and simulation results, it is shown that the main reason of this dependence is the distance of the charge distribution centroid from the interfaces, which is controlled by both front and back-gate bias voltages, and the way this distance affects the Remote Coulomb scattering coefficient a. A new LF noise model approach is proposed to include all these effects. This also allows us to assess the oxide trap density values for both interfaces.

For the first time, CMOS devices on UTBOX 25nm combined with strained SOI (sSOI) substrates have been demonstrated. A 20% Ion boost is highlighted with these substrates compared to the standard UTBB SOI ones. Performance up to 1530µA/µm @ Ioff=100nA/µm (Vd 1V) for a nominal Lg=30nm with a CET of 1.5nm for the NMOS has been achieved. The viability of this substrate has been demonstrated thanks to our hybrid process, through threshold voltage modulation and leakage current reduction, with back biasing for short devices. In addition, cell current improvement of 23% in 0.12µm2 bitcell is noticed for sSOI at the same stand-by current vs the standard UTBB SOI. Finally, the functionality of hybrid ESD device underneath the BOX is demonstrated.

In this paper, we present TDDB, HCI and BTI reliability characterization of Nfet and Pfet devices issued from FDSOI and bulk 28nm technologies. 28nm FDSOI devices achieve 32% improved performance, 40% reduced power consumption and improved matching. From device level tests, 28nm FDSOI also demonstrates intrinsic reliability behavior similar to 28 bulk devices, giving confidence in the robustness of this technology.

In this paper, we present, for the first time, a thorough investigation of low frequency noise (LFN) and statistical noise variability in high-k/metal gate stack 28nm bulk and FD-SOI CMOS transistors. The experimental results are well interpreted by Monte-Carlo LFN simulations based on the random spatial and energy distribution of discrete traps in the gate dielectric. Our results clearly indicate that the LFN variability of 28nm FD-SOI CMOS technology is improved as compared to previous 45nm and 32nm bulk CMOS technologies.

We report a detailed experimental and theoretical investigation of the effect of residual strain, and strain relaxation, which manifests itself at the Si/SiO$_{2}$ interfaces in commercial silicon-on-insulator (SOI) wafers. SOI material is made of a single-crystal silicon overlayer (SOL) on top of an insulator (buried SiO$_{2}$ layer) sitting on a handle silicon wafer. Infrared reflectivity spectra show that the buried SiO$_{2}$ layer relaxes continuously when thinning the SOL. At the same time the SOL surface roughness and the linewidth of optical phonons in Si near the Si/SiO$_2$ interface (probed by micro-Raman specroscopy) increase. In the as-delivered wafers, this comes from a slight expansion of Si on both sides of the buried SiO$_{2}$ layer which, conversely, is compressed. Thinning the SOL modifies these initial equilibrium conditions. To get quantitative results, we have modeled all our Raman spectra using a theory of inhomogeneous shift and broadening for optical phonons, which takes into account the phonon interaction with the static strain fluctuations. From the variation of linewidth versus interface distance, we have found that the mean squared strain continues to relax in the bulk of the wafer through a depth on the order of several $\mu m$. We also show that the SOL surface roughness is related to strain fluctuations near the Si/SiO$_2$ interfaces., Comment: 28 pages, 11 figure, to be published in Phys. Rev. B (Nov 15 2000)

In this paper, we demonstrate for the first time full integration of highly performant NMOS and PMOS silicon-on-nothing (SON) devices into circuits. We demonstrated fully functional SRAMs cells with very good yield, showing static noise margin (SNM) of 175mV and write margin (WM, stable "read 0") above 500mV. The optimized SON devices show performance for NMOS and for PMOS that is among the best published data (with drive current up to 1100/350/spl mu/A//spl mu/m for 138/20nA//spl mu/m I/sub off/ for NMOS and PMOS devices respectively @V/sub dd/=1.2V, I/sub ox/=16A). Finally, we present also the implementation of the SON process into a new "localized SOI" architecture on bulk. This new and simplified SON process is also demonstrated by fully operational SRAM cells.

This work investigates experimentally the non-linearities of FDSOI MOSFETs from DC to RF frequencies. The effect of the back-gate bias on non-linearity of the device is studied by means of 2nd and 3rd harmonic distortions (HD2 and HD3) extracted from dc I-V curves as well as from large-signal RF measurements using 1-dB and IP3 points. It is shown that the non-linearity is reduced by applying a positive back-gate bias. The reasons for this reduction are increasing of “effective body factor” and lesser mobility degradation with increase of the positive back-gate bias.

For the first time, the thermal stability of a 28nm FDSOI CMOS technology is evaluated with yield measurements (5Mbit dense SRAM and 1 Million Flip- flops). It is shown that 500°C 2h thermal budget can be applied on a digital 28nm circuit including State-Of- The-Art Cu/ULK BEOL without yield nor reliability degradation. These results pave the way to the introduction of BEOL between tiers in 3D sequential integration while the thermal budget allowed for the top tier is sufficient to lead to high performance device.