Search

The coating process on food packaging paper is carried out to improve the food safety aspect from dangerous substance migration from food packaging into food. It can facilitate to increase its function and wide the potency of utilization. The coating materials commonly used are plastic and wax coatings. Chitosan as a natural polymer that has the binding properties both water and oil. Chitosan has polar and non-polar groups thus it is potential to be developed as a coating material for food packaging paper. The purpose of this study was to determine the physical-mechanical and antimicrobial properties of food packaging paper from oil palm empty fruit bunches pulp coated with chitosan. The parameters used were chitosan and pulp weight. The oil palm empty fruit bunch pulp was fibrillated with high speed blender then mixed with chitosan solution. The mixed solution was poured in the mold and dried in an oven at 60 °C for 24 hours. The results showed that increasing of chitosan content was coated paper increased physical and mechanical properties values. The more pulp content the higher the physical properties value, however the mechanical properties value tend to decrease. The antimicrobial activity of chitosan coated paper was evaluated by measuring the diameter of the inhibition zones. The results revealed that all tested samples showed growth inhibition zone againts to Escherichia coli and Staphylococcus aureus after 24 h incubation compared to commercial food packaging paper.

Indonesia has targeted to reach 23% of renewable energy share by 2025. In order to meet the target, many researchers have focused on the explorations of renewable energy resources. One of the potential solutions to meet the target is the agricultural wastes, include corn cobs and areca nut fiber. In this study, the calorific value of corn cobs and areca nut fiber are tested. The corn cobs and areca nut fiber are collected from the farmers in Sumatera Utara province of Indonesia. In addition, the Paper waste is also tested. A bomb calorimeter of IKA C6000 is used to measure the energy content of the biomass. The results show that the calorific value of Corn cobs and Areca nut fiber is 5573 Cal/g and 4946 Cal/g, respectively.By using the average yearly production of Corn and Areca nut, these calorific values similar to 4,539 TOE and 4,653 TOE, respectively. If the potency can be used to replace the coal as an alternative fuel, this potency will reduce the Greenhouse gas (GHG) emission. The potency of mitigation GHG by replacing Corncob and Areca nut fiber are 18,306 and 18,491 ton of CO2e.

Recycled paper mill effluent (RPME) contains high concentrations of organic matters and total solids, and therefore requires proper treatment prior to discharge. There is a lack of experimental data available on the biodegradation of solids contents of RPME and digested sludge in anaerobic reactors. In this study, the treatment of RPME was studied using five compartments modified anaerobic inclining-baffled reactor (MAI-BR). The compartmental profiles of TSS, VSS, TDS and lignin contents, and floc size were investigated at different influent chemical oxygen demand concentration (CODin) from 1,000 to 4,000 mg/L, and hydraulic retention time (HRT) from 3 to 1 days (corresponding to organic loading rate (OLR) from 0.33 to 4 g/L day). The results showed that the contents of TSS, VSS and lignin were the highest at Compartment 1 (14,818-32,130 mg/L), (6,772-20,548 mg/L) and (7-227 mg/L), and gradually decreased towards Compartment 5 (627-8,518 mg/L), (281-6,145 mg/L) and (7-22 mg/L), respectively. Conversely, the content of TDS was low at Compartment 1 (508-712 mg/L) and slightly increased towards Compartment 5 (531-836 mg/L). Throughout 126 days, the floc size at Compartmental 1 was increased from 104 to 731 µm, similarly for other compartments. These results concluded that Compartment 1 played a major role in the operation of MAI-BR treating RPME.Recycled paper mill effluent (RPME) contains high concentrations of organic matters and total solids, and therefore requires proper treatment prior to discharge. There is a lack of experimental data available on the biodegradation of solids contents of RPME and digested sludge in anaerobic reactors. In this study, the treatment of RPME was studied using five compartments modified anaerobic inclining-baffled reactor (MAI-BR). The compartmental profiles of TSS, VSS, TDS and lignin contents, and floc size were investigated at different influent chemical oxygen demand concentration (CODin) from 1,000 to 4,000 mg/L, and hydraulic retention time (HRT) from 3 to 1 days (corresponding to organic loading rate (OLR) from 0.33 to 4 g/L day). The results showed that the contents of TSS, VSS and lignin were the highest at Compartment 1 (14,818-32,130 mg/L), (6,772-20,548 mg/L) and (7-227 mg/L), and gradually decreased towards Compartment 5 (627-8,518 mg/L), (281-6,145 mg/L) and (7-22 mg/L), respectively. Conversely, t...

The blended learning (BL) services presented for the academic accreditation process of universities and other educational institutions is a policy that has been used rapidly in the educational area. This process represents a real challenge and a need for institutions to function by the challenges in the ways of development for the attainment of faculty and student satisfaction. The need for learning management systems (LMS) becomes a real advance to control the management of technological development. The purpose of this study is to overcome these challenges and speed up the whole e-learning process in a different manner. The study revealed the existence of an important gap between the important features of blended learning applications and the control management of LMS. The finding shows a systematic analysis of existing technologies and their effects on accreditation checkpoints approval for the underlying conception of the assessment processes involve perspectives that relate to what is now considered valuable or desirable concerning the institution of higher education.

Principal Component Analysis (PCA) is a commonly used unsupervised exploratory analysis technique. It is also frequently used in dimensionality reduction. This preliminary paper investigates the feasibility of three variants of PCA, i.e. independent PCA (iPCA), sparse PCA (sPCA), and sparse independent PCA (siPCA) on forensic classification of paper based on their IR spectral data. After that, Linear Discriminant Analysis (LDA) models were built using the Principal Components (PCs) produced by the PCA and the three aforementioned variants. The performances of all these four LDA models, i.e. PCA-DA, iPCA-DA, sPCA-DA and siPCA-DA, were evaluated via leave-one-out cross-validation on the data set. The results obtained show that iPCA-DA and siPCA-DA are the most effective models with 100.0% classification accuracy. Then, the effectiveness of siPCA and iPCA models was evaluated based on posterior probability used for predictions of class membership that were derived from leave-one-out cross-validation. As a conclusion, siPCA is identified as the best classification model.

Historians and librarians are interested in watermarks and mould surface patterns in historic papers, because they represent the “fingerprints” of antique papers. However, these features are usually covered or hidden by printing, writing or other media. Different techniques have been developed to extract the watermarks in the paper while avoiding interference from media on the paper. Beta radiography provides good results, but this method cannot be widely used because of radiation safety regulations and the long exposure times required due to weak isotope sources employed. In this work, two promising methods are compared which can be used to extract digital high-resolution images for paper watermarks and these are electron radiography and low energy X-ray radiography. For electron radiography a “sandwich” of a lead sheet, the paper object, and a film in a dark cassette, is formed and it is exposed at higher X-ray potentials (> 300 kV). The photoelectrons escaping from the lead sheet penetrate the paper and expose the film. After development, the film captures the watermark and mould surface pattern Images for the paper being investigated. These images are then digitized using an X-ray film digitizer. The film employed could potentially be replaced by a special type of imaging plate with a very thin protection layer to directly generate digital Images using computed radiography (CR). For the second method, a low energy X-ray source is used with the specimen paper placed on a digital detector array (DDA). This method directly generates a low energy digital radiography (DR) image. Both methods provide high quality images without interference from the printing media, and provide the potential to generate a “fingerprint” database for historical papers. There were nevertheless found to be differences in the images obtained using the two methods. The second method, using a low energy X-ray source, has the potential to be integrated in a portable device with a small footprint incorporating user safety requirements. Differences obtained using the two methods are shown and discussed.

EMG is a medical technique that measures muscle response or electrical activity in response to a nerve’s stimulation of the muscle [10]. In this paper we have classified multiple hand gestures using small number of electrodes. This report aims to review current use of EMG based control system and explain the existing challenges. The stages involved includes data acquisition, feature extraction, classification and controller. Some of the application includes Arm rehabilitation, game controller, wheel chair controllers, etc.

Lateral light scattering simulations of printed dots are analyzed using general radiative transfer theory. We investigated the appearance of a printed paper in relation to the medium parameters like thickness of the paper sample, its optical properties, and the asymmetry factor. It was found that the appearance of a print greatly depends on these factors making it either brighter or darker. A thicker substrate with higher single scattering albedo backed with an absorbing surface makes the dots brighter due to increased number of scattering events. Additionally, it is shown that the optical effects of print also depend on illuminating and viewing angles along with the depth of ink penetration. A larger single scattering angle implies less intensity and the dots appear much blurred due to the shadowing effect prominent when viewed from sides. A fully penetrated dot of the same extinction coefficient as a partial penetrated one is darker due to increased absorption. These results can be used in applications dealing with lateral light scattering.

Paper-based PbS photodetector sensitive in the visible spectrum is reported. Nanocrystalline PbS-on-paper devices are fabricated by a spin coating method on white paper (300 GSM) from a methanolic precursor solution. Photodetector cells of gap 0.2 cm and length 0.5 cm are prepared by drawing contacts by monolithic cretacolor 8B pencil. X-ray diffractometer confirmed the deposition of nanocrystalline PbS films with 14 nm crystallites. The SEM illustrated the uniform coating of nanocrystalline PbS thin films on cellulose fibres of papers having an average thickness of fibres are 10 µm. The linear J-V characteristics in dark and under illumination of light using graphite trace on nanocrystalline PbS-on-paper shows good ohmic contact. The resistivity of pencil trace is 30 Ω·cm. Spectral response measurements of photodetector reveal the excellent sensitivity from 400 to 700 nm with a peak at 550 nm. The best responsivity anddetectivity are 0.7 A/W and 1.4 × 1012 Jones respectively. These paper-based low-cost photodetectors devices have fast photoresponse and recovery without baseline deviation.

Here, we presented a novel, cost effective approach to fabricate flexible piezoelectric nanogenerator (NG) consisting of ZnS nanowires (NWs) grown upon cellulose. An output voltage of 4 V is generated from the nanocomposite paper (NC-paper) based NG. Subsequently, it has the capability to power Light Emitting Diode (LED) and charging up capacitor. The corresponding energy stored in the capacitor (1 µF) is 16 µJ. Thus, the fabricated NC-paper based NG can be used for smart textile structures, wearable and self-powered nanodevices.

The commercial telecommunication system in future would explore the electromagnetic spectrum with higher frequency than used now, because it requires higher speed of transmission data. Using the millimeter waves (mmW) with frequency ranging from 30 to 300 GHz, such requirement could be fulfilled. The upcoming 5G cellular technology is expected to use frequency 30 GHz or higher. Then materials with a specific characteristic at the mmW range are interesting to be explored and investigated. Here, we report the synthesis process of graphene/TiO2 deposited on paper and their transmission characteristics to the electromagnetic energy at frequency 27-40 GHz (Ka-Band). The reduced graphene oxide (rGO) was synthesized by a modified Hummers method with introduction of microwave irradiation in the process. rGO and TiO2 were mixed in ethanol solution and deposited on the paper by a spraying technique. Transmission coefficient of electromagnetic wave energy at Ka-Band was measured by using the millimeter vector networ...

An algorithm for constructing super-large semantic networks has been developed in current work. Algorithm was tested using the “Cosmos” category of the Internet encyclopedia “Wikipedia” as an example. During the implementation, a parser for the syntax analysis of Wikipedia pages was developed. A graph based on list of articles and categories was formed. On the basis of the obtained graph analysis, algorithms for finding domains of high connectivity in a graph were proposed and tested. Algorithms for constructing a domain based on the number of links and the number of articles in the current subject area is considered. The shortcomings of these algorithms are shown and explained, an algorithm is developed on their joint use. The possibility of applying a combined algorithm for obtaining the final domain is shown. The problem of instability of the received domain was discovered when starting an algorithm from two neighboring vertices related to the domain.

CdSe quantum dot has great potential in various applications especially for emitting devices. One example potential application of CdSe quantum dot is security label for anti-counterfeiting. In this work, we present a practical approach of security label on paper using one and two colors of colloidal CdSe quantum dot, which is used as stamping ink on various types of paper. Under ambient condition, quantum dot is almost invisible. The quantum dot security label can be revealed by detecting emission of quantum dot using photoluminescence and cnc machine. The recorded quantum dot emission intensity is then analyzed using home-made program to reveal quantum dot pattern stamp having the word ’RAHASIA’. We found that security label using quantum dot works well on several types of paper. The quantum dot patterns can survive several days and further treatment is required to protect the quantum dot. Oxidation of quantum dot that occurred during this experiment reduced the emission intensity of quantum dot patterns.

Selection of the most significant variables, i.e. the wavenumber, from an infrared (IR) spectrum is always difficult to be achieved. In this preliminary paper, the feasibility of genetic algorithms (GA) in identifying most informative wavenumbers from 150 IR spectra of papers was investigated. The list of selected wavenumbers was then employed in Linear Discriminant Analysis (LDA). GA procedure was repeated 30 times to get different lists of variables. Then the performances of LDA models were estimated via leave-one-out cross-validation. A total of six to eight wavenumbers were identified to be valuable variables in the GA procedures. All the 30 LDA models achieve correct classification rates between 97.3% to 100.0%. Therefore the GA-LDA model could be a suitable tool for differentiating white papers that appeared to be highly similar in their IR fingerprints.

We successfully developed a method utilizing colloidal CdSe nanocrystalline quantum dot for anti-counterfeiting label on a piece of glossy paper. We deposited numbers and lines patterns of toluene soluble CdSe quantum dot using rubber stamper on a glossy paper. The width of line pattern was about 1-2 mm with 1-2 mm separation between lines. It required less than one minute for deposited CdSe quantum dot on glossy paper to dry and become invisible by naked eyes. However, patterned quantum dot become visible using long-pass filter glasses upon excitation of UV lamp or blue laser. We characterized photoluminescence of line patterns of quantum dot, and we found that emission boundaries of line patterns were clearly observed. The error of line size and shape were mainly due to defect of the original stamper. The emission peak wavelength of CdSe quantum dot was 629 nm. The emission spectrum of deposited quantum dot has full width at half maximum (FWHM) of 30-40 nm. The spectra similarity between deposited quant...

In response to published reports about the decline in funding for space nuclear power, the Board of Directors of the American Institute of Aeronautics and Astronautics (AIAA) approved a position paper in March 1995 that recommends (1) development and support of an integrated space nuclear power program by DOE, NASA and DoD; (2) Congressional support for the program; (3) advocacy of the program by government and industry leaders; and (4) continuation of cooperation between the U.S. and other countries to advance nuclear power source technology and to promote safety. This position paper has been distributed to various people having oversight of the U.S. space nuclear power program.

Prior work has established the existence of a color-performance relationship in achievement contexts and has demonstrated its presence in some undergraduate course examinations. This study examines the manifestation of such a relationship in an introductory, 430-student, calculus-based electricity and magnetism course during which the paper color used in examinations was varied. In this report, we analyze three separate exams and differentiate between students’ multiple choice, written response, conceptual, and computational performances. Also considered are factors such as the time students require to complete exams and their confidence levels prior to and immediately following assessment. Performance in all categories appears to be independent of paper color.

In this paper we present an application of two Computational Intelligence Algorithms, namely Particle Swarm Optimization (PSO) Algorithm and Differential Evolution (DE) for finding and optimal solution to two optimization problems that occur in a paper industry. The first problem deals with the economic optimization of a hypothetical but realistic Kraft pulping process and in the second problem we have considered the optimization of Boiler load allocation problem. Both the problems form an integral part of paper making process. The simulation results show the efficiency and time effectiveness of DE and PSO.

Due to the rising difficulty of developing complex systems a lot of research has gone into the multi‐agent paradigm over the past decades, during which a vast array of approaches for developing such systems have been proposed. Despite this fact there seems to be a gap in the MAS community between solutions that provide for expressivity and those that offer generality. It is our opinion that embedding the MAS language into a functional language we can have the best out of both worlds: we can implement the desired semantics in an abstract way, allowing us to focus on the problem domain, i.e. complex, distributed MAS. Our approach is going to be layered: (i) we start from a statically typed functional language and build an EDSL that acts as an executable specification language for single agent entities; and (ii) develop a framework for workflow‐oriented coordination on top of the previous layer and investigate its use as a means of implementing agent organizations, focusing on coordination and communication.

At the 2007 Physics Education Research Conference, a workshop on publishing and refereeing was held with a panel of editors from four different publishing venues: the physics education research section of the American Journal of Physics, the Journal of the Learning Sciences, Physical Review Special Topics–Physics Education Research, and the Physics Education Research Conference Proceedings. These editors answered questions from participants regarding publishing in their respective venues, as well as writing referee reports that would be useful to both journal editors and authors. This paper summarizes the discussion.

An important material property in the paper industry is the anisotropic stiffness distribution due to the fibrous microstructure of paper. Ultrasonic methods offer a means of determining the stiffness of sheets of paper from the anisotropic propagation characteristics of elastic Lamb waves along the machine direction (MD) and the cross direction (CD). Currently, piezoelectric ultrasonic methods are employed in the industry to measure the elastic polar diagram of paper through multiple contacting measurements made in all directions. This paper describes a new approach utilizing the INEEL Laser Ultrasonic Camera to provide a complete image of the elastic waves traveling in all directions in the plane of the paper sheet. This approach is based on optical dynamic holographic methods that record the out of plane ultrasonic motion over the entire paper surface simultaneously without scanning. The full-field imaging technique offers great potential for increasing the speed of the measurement and it ultimately pr...

On-line measurement of material properties is a goal of many manufactures for production improvement and quality control. In the paper industry, the elastic stiffness of the paper web needs to be accurately measured and controlled online. Currently, contact ultrasonic methods are employed to measure the elastic constants of paper offline. Piezoelectric transducers are placed in contact with the paper surface to generate and detect plate wave modes, known as Lamb wave modes, in the paper in both the machine and cross directions. Laser ultrasonics offers a new approach to making elastic wave measurements that does not require contacting the paper web. A pulsed laser generates ultrasound in the paper by delivering a high intensity short impulse to the paper through thermoelastic expansion. An optical interferometer is used to demodulate the small phase modulation that the elastic wave produces on a continuous probe laser beam. Difficulty in applying this approach to online measurements of rapidly moving pape...

Microwave energy offers the drying/curing industry a new prospect in efficient and uniform drying. In paper drying, due to the fact that absorption power depends on loss factor, more heat is developed in wet areas thus resulting in automatic moisture profile correction. During drying the most important parameter is maintaining the pre-prescribed level of moisture content. The correlation equation between absorbed power and moisture contents has been developed, in order to program the controlling hardware related to the level of drying power.

The purpose of this paper is to study the Lean-TRIZ initiative within the context of service sector organizations. In addition, article has the objective to determine the Readiness Factors (RF) for the successful implementation of Lean- TRIZ in service sector organization. The research has utilized secondary data to justify the need for RF. Data from various indexed papers and conference papers were studied. The data thus obtained was coupled with the vast experience and the expertise of the authors in Lean implementation in service sector organization. The papers present RF which are essential for the sustainability of Lean-TRIZ in a service sector organization and provides a framework for the successful implementation. This is a theatrical paper based on the author’s vast experience in service sector organization and existing literature. Lean-TRIZ is still in embryonic stage with most of the academic literature only in conferences and there is a serious dearth in literature. Future researchers can focus on empirical studies in specific service sector organizations.

Human immunodeficiency virus and acquired immune deficiency syndrome (HIV/AIDS) is pandemic. It has affected nearly 60 million people since the detection of the disease in 1981 to date. In this paper basic deterministic HIV/AIDS model with mass action incidence function are developed. Stability analysis is carried out. And the disease free equilibrium of the basic model was found to be locally asymptotically stable whenever the threshold parameter (RO) value is less than one, and unstable otherwise. The model is extended by introducing two optimal control strategies namely, CD4 counts and treatment for the infective using optimal control theory. Numerical simulation was carried out in order to illustrate the analytic results.

The study focused on the treatment of real oilfield produced water from the East Baghdad field affiliated to the Midland Oil Company (Iraq) using an oil skimming process followed by a coagulation/flocculation process for zero liquid discharge system applications. Belt type oil skimmer was utilized for evaluating the process efficiency with various operating conditions such as temperature (17-40 °C) and time (0.5-2.5 hr.). Polyaluminum chloride (PAC) coagulant and polyacrylamide (PAM) flocculant was used to investigate the performance of the coagulation/flocculation process with PAC dosage (5-90 ppm) and pH (5-10) as operating conditions. In the skimming process, the oil content, COD, turbidity, and TSS decreased with an increase in temperature and time. The best temperature and time for oil skimming are 40 °C and 2.5 hr. which gives 95.8%, 94.9%, 31.5%, and 33.2% removal for oil content, COD, turbidity, and TSS respectively. In the coagulation/flocculation process, the optimum PAC dosage and pH are 55 mg/l and 6.4 which gives 100%, 96.5%, and 97.7% removal for oil content, turbidity, and TSS respectively.

The production of activated carbon using heat from microwave processing for activation time was successfully conducted and its performance in treating textile dye effluent was observed through various factors such as phosphoric acid loading used, contact time, dosage of activated carbon and pH. Activated carbon with phosphoric acid loading of 60% shown highest BET surface area that was 213.52 m2/g however, it obtained least thermal stability. The result indicated that about 97.11% of dye from textile effluent can be removed in only 90 minutes of contact time at pH 3 with the use of 2.0 g of produced activated carbon. The production of activated carbon using microwave processing can be an alternative way for activation process using conventional furnace heating. The used of rubber wood sawdust as the raw material for activated carbon production can solve the waste issue from sawmill as an example.

Research in the field of Telecommunication is dynamic and continuously working towards the social community of the people. Among that predicting the customer’s who likes to switch from the current network provider is the most important part of telecom industry. However, there are a lot of research has done on this topic, but still more improvements and advancements are expected. In this position paper, we put forward the comparison model of different churn mining methods that intends to help in predicting the customer churn rate in a better way. This paper provides a benchmark of various mining algorithms and its methods for prediction of customer churn rate, which makes the telecommunication industry to setup the retention policies with the increase of their profit.

Bio-energy is renewable energy made from plant. Biomass-based energy sources are potentially CO2 neutral and recycle the same carbon atoms. In order to reduce pollution caused by fossil fuel combustion either for mechanical or electrical energy generation, the performance characteristic of purified palm oil blends are analyzed at various ratios. Bio-energy, Pure Plant Oil, represent a sustainable solution.A generator has been modified due to adapt the viscosity ofblended fuel, PPO - diesel, by pre-heating. Several PPO - diesel composition and injection timing were tested in order to investigate the characteristic of mixed fuel with and without pre-heating. The term biofuel refers to liquid or gaseous fuels for the internal combustion engines that are predominantly produced fro m biomass. Surprising result showed that BSFC of blended PPO - diesel was more efficient when injection timing set more than 15° BTDC. The mixed fuel produced power with less mixed fuel even though the calorie content of diesel is higher than PPO. The most efficient was 20% PPO in diesel with BSFC 296 gr fuel / kwh rather than 100% diesel with BSFC 309 gr fuel / kwh at the same injection timing 18° BTDC with pre-heating. The improvement of BSFC is caused by heating up of mixed fuel which it added calorie in the mixed fuel. Therefore, the heating up of blended PPO - diesel is not only to adapt the viscosity but also improving the efficiency of fuel usage representing by lower BSFC. In addition, torque of the 20% PPO was also as smooth as 100% diesel representing by almost the same torqueat injection timing 15° BTDC. The AIP Proceedings article template has many predefined paragraph styles for you to use/apply as you write your paper. To format your abstract, use the Microsoft Word template style: Abstract. Each paper must include an abstract. Begin the abstract with the word “Abstract” followed by a period in bold font, and then continue with a normal 9 point font.

Demand for fossil fuel of coal, petroleum and natural gas has always increased from year to year. Therefore, the development, expansion and utilization of biomass from non no-fossil fuels need be carried out. Efforts to explore, develop, process and utilize biomass from non-fossil fuels, which is the cultivation of microalgae containing triglycerides that can be extracted into methyl esters (biodiesel). The sample extraction process is carried out in 5 stages, such as harvesting, weaving, methylation, extraction, and washing. The amount and ratio of saturated and unsaturated fatty acid is a key that determines the suitability of microalgae as a biofuel feedstock. This paper aims to compare the potential microalgae in Indonesia with the other countries as feedstock for biofuel production. The fatty acid composition of Synechococcus sp. HS-9, Spirulina platensis, Glagah consortium microalgae, and Nostoc HS-20 from Indonesia could be a promising feedstock for biofuel production. The quantity of fatty acid microalgae from Indonesia higher than the other countries.

The present study was carried out to beneficiate coal tailings sample using froth flotation technique. The aim of the investigation was to remove the carbonaceous material present and to reduce the environmental pollution generated through large volume of tailings from a coal preparation plant. The characterization studies show that the sample contains D80 passing size as 276 µ and D50 as 182 µ. The proximate analysis indicated that the coal sample contains 45.3% ash and 34.5% fixed carbon. Froth flotation experiments were carried out at varying parameters of collector dosages (0.60, 0.67 & 0.71 kgpt), frother dosages (0.33, 0.44& 0.51 kgpt) and pulp density (8%, 10% & 12% w/w). The experimental results indicated that the optimum amount of clean coal may be recovered from tailings with an ash content of 18.46% in the clean coal with an appreciable yield of 64.13%. The optimum results were obtained at frother dosage of 0.44 kgpt and collector dosage of 0.60 kgpt with pulp density of 10% (w/w).

The improvement of air pollution issues and excessive road transportation dependence on crude oil is not possible today without the implementation of new mobility concepts, preferably complying with the principles of sustainable social and economic development. The lack of these concepts, as emphasized in the White Paper, Roadmap to a Single European Transport Area – Towards a competitive and resource efficient transport system, will preserve transportation dependence on crude oil so deeply that only 10% of energy will be derived from renewable sources. According to this scenario, until 2050 the CO2 emissions in the transportation sector will increase by one third compared to 1990. Moreover, there will be an increase in the costs of traffic congestion until 2050 by ca. 50%. The difference in availability between central and peripheral areas and social costs of accidents and noise pollution will increase as well [1].

The adverse environmental degradation created by various plastics produced from petroleum products is a major concern for the world nations. The developed and developing nations have adopted various strategies on the production and usage of highly hazardous conventional plastics. Various research works have been undertaken to formulate a sustainable alternative for the conventional plastics. In this regard, an effort was made to synthesis a biodegradable polymer for large scale commercial usage in packaging applications. Biodegradable polymers can be produced from various resources. The study involves the production of bio-plastic from Banana peel and Prosopis juliflora. Cellulose, a major component required for biopolymer synthesis was extracted from Prosopis juliflora which then combined and processed with dried banana peel. Additives and preservatives that contributes to the polymer characteristics were added in suitable proportions and processed under defined conditions. The mixture was then dried at a temperature of 130 ℃ to yield the final product. The biopolymers thus produced were tested for its water absorption capacity, thermal resistance, tensile strength, biodegradability and microbial attacks. It was observed that water absorption capacity of the biopolymer was lower for lesser starch and higher cellulose concentrations. The tensile strength was found to be 0.67 N/mm2 which was due to the addition of zinc oxide. No microbial attack was observed during storage and it was also found that the biopolymer was able to withstand high temperature up to 130 °C during its usage.

Disposal of untreated waste in the environment leads to the creation of harmful diseases, greenhouse gases and climate change. So the demand arises to eliminate or avoid these kinds of risks to both the society as well as environment. Because of this there are enormous solutions and ideas that are playing a crucial role in this risk avoiding activity. In this study, adsorbent has been synthesized by hydrothermally treating the horse manure. The effect of this synthesized adsorbent produced from horse manure was studied for the removal of toxins like methylene blue, ethyl orange, azo dyes and crystal violet dyes which is presented in the textile effluent. These dyes can create severe illness to both the people as well as aquatic species while it is mixed with natural water bodies.

The increasing of scarce of petroleum availability, unstable prices, and potential environmental damage due to the use of fossil fuel encourage the development of alternative fuels that can replace fossil fuels, including jet fuel. Bio-jet fuel is a renewable fuel that has similar characteristics to jet fuel. The potential raw material for bio-jet fuel production in Indonesia is coconut oil. The composition of fatty acids in coconut oil corresponds to the range of carbon atomic chain of jet fuel. Indonesia is also the country with the second-largest share of coconut oil exports in the world which shows that the use of coconut oil in Indonesia is very less. In this study, bio-jet fuel was synthesized from coconut oil through hydrodeoxygenation reaction to convert fatty acids to hydrocarbons by removing oxygen. The catalyst used in this reaction was NiMoP/Al2O3 catalyst. The hydrodeoxygenation reactions were carried out with variations of pressure and temperature, at pressures of 10, 15, and 20 bar, and temperatures of 375, 385, and 400°C. The reactions were stopped if they had reached equilibrium based on GC-TCD analysis of the gas product. The hydrodeoxygenation reaction at 400°C and 20 bar was able to produce high conversion (92.56%), much hydrocarbon content (91.91%), high selectivity and also yield of bio-jet fuel (82.93% and 54.34%). Liquid products were distilled to obtain jet fuel fraction products. From the results of the density, viscosity, acid number, heating value, and freezing point analysis of the bio-jet fuel distillate, good values were obtained.

One of the main factors that cause the earth that we live in is not as clean as it was before is the utilization of fossil fuel. Motorized vehicles still utilize fossil fuel as energy sources, and the number of motorized vehicles is growing every year. Biomass energy are one of the alternative energies currently being developed. Bioethanol are one of the technologies for fuel in motorized vehicles to utilize biomass as an alternative energy. The addition of bioethanol to gasoline will certainly change the fuel properties, the fuel will be more difficult to self-ignite so the pressure generated in the combustion chamber will be more consistent. Coefficient of variation (COV) represent the ratio of the standard deviation to the mean of a set of data, in this study in cylinder pressure data (IMEP) is used. Based on previous research that discussed the analysis of emission gas and fuel consumption on SI engine fueled with low-grade bioethanol and oxygenated additive, the authors examined further to analyze the characteristic of ethanol blend and oxygenated additive to COVIMEP and Heat Release Rate (HRR) of various fuel mixture as well as COVIMEP correlation with HRR at variable engine speed were investigated. The result show that compared with pure gasoline, ethanol blend decreases HRR. When oxygenated additive added to gasoline – ethanol blend, it increases its maximum heat release rate especially on fuel mixture E5 about 6.2% compared to E0. And the Correlation of COV and HRR; as COV value increases, HRR decreases. Whereas, when COV value decreases, HRR increases.

In order to improve the quality and the separation effect of CO2 in X gas field, the influence of swing on removing of water content on purification of CO2 from offshore natural gas by pressure swing adsorption (PSA) and triethylene glycol (TEG) absorption was investigated by simulation. This method is to reduce the water content in the CO2 gas for enhanced oil recovery (EOR) method. In the EOR injection process at Y oil field, the purity of CO2 is more than 95%. The purity of CO2 plays an important role in determining the amount of oil that can be recovered. In system using PSA, the mass of activated carbon is needed of 11,555.3 lb/day, whereas by TEG absorption is required 91.27 gpm TEG adsorbent. Economic analysis was also carried out based on the oil yield that can be recovered from well (20.53 MMstb) using CO2 from X gas field for EOR injection in Y oil field. In PSA integrated system showed net present value (NPV) of 349,376,372.23 $ US, internal return rate (IRR) of 19.87%, with an investment cost of 214,918,114 $ US. The system integrated with TEG dehydration has an NPV of 390,869,013.8 $ US, IRR of 20.37%, and an investment cost of 240,111,000 $ US. These results showed that CO2 purification from X gas field is the most optimal and efficient when the system used the TEG absorption with NPV of 423,392,895.6 $ US, IRR of 20.71%, and payback period of 4.06 years. Based on the results of comparisons between the PSA and TEG features of upgrading technologies of CO2 in X gas field, the specific requirements for CO2-EOR in Y oil field, recommendations are made regarding appropriate technology for CO2−EOR

Coal consumption in the Indonesian metallurgical industry in 2015 has reached up to 3.5 million tons. One ton of pig iron required 0.5-0.6 tons of coke, 1.4 tons of iron ore, and 0.25 tons of limestone. Coke added by the charcoal is called bio- coke. Charcoal, as the raw material of coke from the carbonization process of Indonesian redwood residues, can reduce the consumption of coking coal. Biomass has been applied as an alternative renewable fuel to the industrial sector to reduce CO2 emissions. The use of biomass reduces the dependence on traditional fossil fuels whose resources are reduced every day. The purpose of this study was to obtain the best charcoal sizes from redwood and improve the quality of bio-coke through the dry cooling process. The final method of bio-coke can be done coke dry quenching to prevent the occurrence of cracks in the coke, increase coke strength, and less chemical activity during cooling. Redwood charcoal with particle size (10, 25, 50, and 80) mesh is blending with coking coal. The mixing, composition of coal with redwood charcoal is 90:10. Blended briquettes with the addition of molasses and wood tar are processed by re-carbonization at 1100 °C for 4 hours. Bio-coke charcoal 50 mesh has bulk density of 1071.44 kg/m3. The strength of bio-coke increases as bulk density increases. The maximum size of the redwood charcoal particles of the study on 50 mesh generated a compressive strength of 4.87 MPa.

The pyrolysis characteristics and kinetic parameters of coal and water hyacinth blend have been investigated by using thermogravimetric analysis. Those of pure coal and pure water hyacinth were also each studied as a comparison. The coal sample was taken from a Sub-district of Gunung Panjang, Berau, East Kalimantan, Indonesia. The as-received sample was ground to be a mesh size of 60. The sample of water hyacinth originated from Dams of Selorejo and Sengguruh, district of Malang, Indonesia. The raw material was cleaned with water and subsequently cut and dried at the temperature of around 85 °C for 6 hours. The dried biomass was then crushed and sieved at a size of 60 mesh as well. The blended fuel was composed of coal and water hyacinth in a mass ratio of 40:60 (wt%). The thermogravimetric experiment was performed for the coal, the water hyacinth, and their blend under the instrumentality of thermal analyzer at a single heating rate of 40 °C/min. The sample was heated up from 27 to 1000 °C with a nitrogen flow rate of 100 ml/min. Thermogravimetric (TG) and derivative thermogravimetric (DTG) curves were obtained. The kinetic evaluation was performed under the fitting method of Coats-Redfern. The results indicated that three stages of decomposition process were encountered during thermal degradation of the individual samples of coal and water hyacinth, as well as their blend. The addition of 60% water hyacinth to the coal provoked the thermal degradation toward the lesser temperature and forced the increase of maximum mass loss rate. The activation energy went to decrease together with the increasing of water hyacinth fraction, i.e., 84.02, 66.72, and 44.45 kJ/mol for respectively the coal, blended fuel, and water hyacinth. These results could be valuable in designing and developing of the reactor of the thermal conversion system on an industrial scale.

Indonesia has abundant natural resources spread throughout the islands. The utilization of these natural potentials has not been fully played and developed to meet daily needs such as for cooking. The purpose of this study is to explore the potential of leaf litter as a domestic source of energy for cooking. In particular, a set of laboratory scaled experiment was conducted by using leaf litter of the species Artocarpus champaden, L., Nephelium lappaceum, L., and Mangifera indica, L. In Indonesia these species are known as Cempedak, Rambutan, and Mangga trees which produce fallen leaf throughout the years. A way of reducing the leaf litter problems by local people is by collecting it from the garden and roof, then burn it to reduce the volume. The experimental work was carried out through some steps. The leaf litter was transformed to biomass briquettes fuel in order to increase energy content for combustion by adding Canola Oil and Starch as a binder. The briquettes were produced manually with minimum mechanical works. Thermal analysis, including calorific value, proximate and ultimate analysis, was performed by standard method and equipment. The experiment was carried out by using a biomass stove with a fuel chamber volume of approximately 660 cm3. A fan was attached to the stove to supply an updraft forced vortex flow of air. Water Boiling Test method was performed to measure the burning characteristic and stove efficiency. It was found that the briquettes (100 grams) from all leaf type tested can boil the water of 1000 ml within 7 minutes. In general, the burning performance of the briquettes were related to proximate and ultimate analysis of the samples. Nevertheless, by comparing the performance using Water Boiling Test suggested that the discrepancies of the performance using different types of leaf litter were not significant. This work showed that leaf litter has the potential as a reliable energy source for cooking in household at rural areas.

Increasing the demand of fossil fuel energy in up-coming days life is become an important problem everywhere, so alternative fuel resources (bio-oil) for reducing the energy demand is produced and compared with conventional fossil fuel. By pyrolysis method, the biomass (solid waste) was converted into pyrolysis oil, which is used as an alternative fuel in the diesel engine without any engine modification. Sweet lime peel and corn pyrolysis oil are blend at 10% with diesel. The results of the tests showed that the brake thermal efficiency of the blends of corn oil and sweet lime peel oil with diesel was greater than diesel and the amount of hydrocarbons, carbon monoxide, carbon dioxide and Nitrogen oxide emissions from corn pyrolysis and sweet lime peel oil was lesser than diesel operation. It was observed that the pyrolysis oil shows better performance and emission characteristics than diesel.

Hybrid Power Plant, which uses solar energy and in situ fuels such as pure coconut oil (PCO) and pure palm oil (PPaO), could be a solution for electricity problem in remote areas in Indonesia. Comparison of performance, and emissions are discussed and analyzed in this paper. For performance parameter, efficiency of hybrid system averages 7% higher compared with diesel engine. BSFC of diesel engine average value by using PPaO and PCO are 7.2% and 4.7% higher than by using diesel fuel. However, the BSEC average values are 4.5% and 3.3% lower than the diesel fuel. For the emission parameters, average value of CO2 emissions from the hybrid system is 21.7% lower than the diesel engine, but average value of CO emissions is 31% higher compared to diesel engine. Significant differences can be observed at average value of NOx emissions by using PCO and PPaO which are 210% and 117% lower compared to the diesel fuel.

Latex is a yellowish colloidal liquid from rubber trees that can be used for natural rubber production. The latex processing creates quite large volume of wastewater that has very strong odor and high organic content which is suitable for biogas production in providing renewable energy resources. The purpose of this research is to study and optimize the biogas production from latex wastewater using 40 L packed bed anaerobic reactors with support media of bio-balls or called anaerobic filter reactor. Some key parameters of sCOD, pH, and methane gas composition have been observed. The reactor was operated batch for 36 days with or without packing media (bio-balls). The optimum results of sCOD removal was 81,73% and methane gas content of 55.089% using reactor with packing. The anaerobic filter column was used in continuous mode with 2L/day influent that can reach a steady condition within about 20 days and produce up to 95% COD removal.

Biodiesel is one kind of alternative fuel that is renewable, biodegradable, oxygenated, and less polluting. High viscosity, density and lower calorific value are the major drawbacks of biodiesel. To overcome drawbacks of biodiesel, many researches were carried out all over the world by blending biodiesel in different ways with fossil fuel and short chain alcohols as oxygenated additives. Recently, researchers concentrated on long-chain alcohol due to its high cetane number, heating value and oxygen content. From outcomes of many previous studies, the use of long chain alcohols with biodiesel is not covered and concluded completely overall. Because of complete data scarcity, more investigations should be carried out on the use of long chain alcohols. This work investigates the combustion characteristics, performances and emissions of a four-stroke single cylinder direct injection diesel engine fuelled with 2-ethyl 1-hexanol (2-EH) at 5%, 10% and 20% with POME fuel blends as a replacement for fossil fuel. The fuel blends were used and compared with diesel fuel. Fuel blends are experimentally tested at a maximum load of 28 N.m and different engine speeds. Results show that HE5 had lower peak pressure than DF by 1.77% and overall lower CO and NOx emissions than DF by 8.5% and 4.1%.

Coal is the cheapest and reliable source for power generation, which has the potential to reduce the dependency on natural gas, particularly for Bangladesh, where the natural gas reserve is very limited. Despite numerous studies on gasification from different parts of the world, there has not been a research study on gasification characteristics of Bangladeshi Barapukurian coal (BBC) under state of the art entrained flow condition. Thus, this study aims to investigate the gasification characteristics of Barapukurian bituminous coal using a high-temperature electrically heated entrained flow gasifier under atmospheric pressure.The effect of the partial pressure of the gasification reagent (CO2) on carbon conversion and gas yield was tested by varying the volume percentage of CO2 in N2 between the temperatures of 1000-1400°C. Furthermore, the influence of particle size on carbon conversion and product gases was also examined using industrially relevant particle sizes: 90-106 µm and 250-300 µm. The results show that increasing the temperature and feed CO2 concentrations increase the carbon conversion, though the temperature is found to be the dominant factor. A maximum carbon conversion of 92 % was achieved using ultimate operating conditions of 1400°C and 40% CO2 for particles size: 90-106 µm, while the conversion was only 65% for particle size: 250-300 µm under identical operating conditions. Overall, the yield of CO was increased while the yield of H2 was decreased with increasing temperatures and CO2 concentrations. The maximum yield of CO and H2 was determined to be 0.93 and 0.14 L/g coal respectively using particle size: 90-106 µm, which is 0.88 and 0.12 L/g coal using particle size: 250-300 µm at a temperature of 1200°C under 10% CO2. The main pollutants measured were HCN, NH3 and H2S in the ppm range. The results of this study will provide a baseline data for the industrial scale entrained flow gasification of BBC under CO2 atmosphere.Coal is the cheapest and reliable source for power generation, which has the potential to reduce the dependency on natural gas, particularly for Bangladesh, where the natural gas reserve is very limited. Despite numerous studies on gasification from different parts of the world, there has not been a research study on gasification characteristics of Bangladeshi Barapukurian coal (BBC) under state of the art entrained flow condition. Thus, this study aims to investigate the gasification characteristics of Barapukurian bituminous coal using a high-temperature electrically heated entrained flow gasifier under atmospheric pressure.The effect of the partial pressure of the gasification reagent (CO2) on carbon conversion and gas yield was tested by varying the volume percentage of CO2 in N2 between the temperatures of 1000-1400°C. Furthermore, the influence of particle size on carbon conversion and product gases was also examined using industrially relevant particle sizes: 90-106 µm and 250-300 µm. The results s...

Bioethanol is a natural product and manufactured by the fermentation of plants containing sugar and starch. Characteristic physical and chemical of bioethanol near to gasoline. As a biofuel, bioethanol can be used as a fuel substitution for gasoline with hopefully can decreasing emission and renewable energy for security energy. The objective of this research was to determine the effect of bioethanol-gasoline blended fuels on the performance SI Engine compared with varying gasoline at the market. The experimental test was using gasoline with octane number 88, 92, 98, with 5%, 10%, 15%, and 20% bioethanol blends. The effect of the bioethanol-gasoline blend on performance SI engine 150 CC is increased research octane number, and to decrease heating value with increasing blending bioethanol can decreasing power and increasing fuel consumption. The one important things in this research had differences of each kind of gasoline toward performance and emission of SI engine.

Energy is the main need of humans to carry out activities with better levels of life. At present, energy for daily life is provided from the processing of crude oil. The availability of crude oil in Indonesia is increasingly limited and the price tends to be expensive. This condition requires alternative energy for fuel availability for households. One alternative energy comes from biomass because biomass is a renewable energy and Indonesia has a very large amount of biomass. Utilization of biomass as an alternative energy source has some limitation due to the non-uniform biomass quality and scattered biomass sources. Due to the lack of biomass quality, biomass needs to be pre-treatment before being used for combustion or gasification process. One of biomass pre-treatment to improve the quality of biomass is torrefaction. Torrefaction is a mild pyrolysis at a temperature between 200-300°C to eliminate water content and a small amount of volatile matter from biomass. The torrefaction biomass will have high energy density and hydrophobic properties. Rice husk is one type of biomass produced from rice processing as waste. Indonesia has large amounts of rice husk waste with an energy potential equal to 7000 MW and is located in a rice mill. In this experiment, the energy content of the torrefaction rice husk was analyzed by observing the effect torrefaction temperature (200, 250 and 300°C) and duration of torrefaction (30, 45 and 60 minutes). At the high temperature of torrefaction (300°C), the rice husk has a darker color with high energy content (3465 kkal/kg) but almost 50 % of initial mass loss by torrefaction.