Search

Packaging insulation materials with high thermal conductivity and excellent dielectric properties are favorable to meet the high demand and rapid development of third generation power semiconductors. In this study, we propose to improve the thermal conductivity of epoxy resin (EP) by incorporating a three-dimensional boron nitride thermally conductive network. Detailedly, polyurethane foam (PU) was used as a supporter, and boron nitride nanosheets (BNNSs) were loaded onto the PU supporter through chemical bonding (BNNS@PU). After immersing BNNS@PU into the EP resin, EP-based thermally conductive composites were prepared by vacuum-assisted impregnation. Fourier transform infrared spectrometer and scanning electron microscope were used to characterize the chemical bonding and morphological structure of BNNS@PU, respectively. The content of BNNS in BNNS@PU/EP composites was quantitatively analyzed by TGA. The results show that the thermal conductivity of the BNNS@PU/EP composites reaches 0.521 W/m K with an enhancement rate η of 30.89 at an ultra-low BNNS filler content (5.93 wt. %). Additionally, the BNNS@PU/EP composites have excellent dielectric properties with the frequency range from 101 to 106 Hz. This paper provides an interesting idea for developing high thermal conductivity insulating materials used for power semiconductor packaging. [ABSTRACT FROM AUTHOR]

Over the last two decades, Electron Energy Loss Spectroscopy (EELS) imaging with a scanning transmission electron microscope has emerged as a technique of choice for visualizing complex chemical, electronic, plasmonic, and phononic phenomena in complex materials and structures. The availability of the EELS data necessitates the development of methods to analyze multidimensional data sets with complex spatial and energy structures. Traditionally, the analysis of these data sets has been based on analysis of individual spectra, one at a time, whereas the spatial structure and correlations between individual spatial pixels containing the relevant information of the physics of underpinning processes have generally been ignored and analyzed only via the visualization as 2D maps. Here, we develop a machine learning-based approach and workflows for the analysis of spatial structures in 3D EELS data sets using a combination of dimensionality reduction and multichannel rotationally invariant variational autoencoders. This approach is illustrated for the analysis of both the plasmonic phenomena in a system of nanowires and in the core excitations in functional oxides using low loss and core-loss EELS, respectively. The code developed in this manuscript is open sourced and freely available and provided as a Jupyter notebook for the interested reader. [ABSTRACT FROM AUTHOR]

Low-energy ion beam irradiation, combined with the introduction of impurities, presents a promising approach for nanopatterning silicon (Si) surfaces. In this research, we investigate the surface evolution of Si (100) surfaces irradiated by 75 eV helium (He) plasma, in the presence of tantalum (Ta), traditionally regarded as an impurity incapable of initiating pattern formation, as evidenced in prior studies. The Ta impurities are pre-deposited onto the Si surfaces using the magnetron sputtering method, which offers a more controlled and quantifiable approach compared with the conventional co-deposition route. After irradiation at 800 K, dense cone arrays are produced on the Si surface. The growth of the cones is explored for fluence spanning (1–10) × 1025 m−2. The cross-sectional scanning electron microscope images indicate that the cone lengths and base width are well characterized by t1/2 dependence. The kinetics of the cone growth follow Fick's law, characterized by an effective diffusive mechanism with the coefficients of diffusion: D = 6.49 ± 0.83 × 10−16 m−2 s−1. Transmission electron microscope observations reveal that the cone has distinct inner and outer parts with different microstructures and a clear interface. The growth mechanism of these cones is elucidated as a composite process involving preferential sputtering, the destabilizing influence of He bubbles, and the migration of adatoms. [ABSTRACT FROM AUTHOR]

The scanning electron microscope (SEM) recordings of dynamic nano-electromechanical systems (NEMS) are difficult to analyze due to the noise caused by low frame rate, insufficient resolution, and blurriness induced by applied electric potentials. Here, we develop an image processing platform enhanced by the physics of the underlying system to track the motion of buckling NEMS structures in the presence of high noise levels. The algorithm is composed of an image filter, two data filters, and a nonlinear regression model, which utilizes the expected form of the physical solution. The method was applied to the recordings of a NEMS beam about 150 nm wide, undergoing intra- and inter-well post-buckling states with a transition rate of approximately 0.5 Hz. The algorithm can track the dynamical motion of the NEMS and capture the dependency of deflection amplitude on the compressive force on the beam. With the help of the proposed algorithm, the transition from inter-well to intra-well motion is clearly resolved for buckling NEMS imaged under SEM. [ABSTRACT FROM AUTHOR]

A non-destructive method for detecting sub-micrometer-sized micropipes on an entire wafer surface is investigated. Since it is difficult to detect sub-micrometer-sized micropipes due to their small core size, a non-destructively and accurately detecting method is required. To solve the issue, we focus on a characteristic depression generated around micropipes, namely, line-shaped depressions. In this paper, the location of line-shaped depressions is identified by using optical inspection, and the line-shaped depressions are distinguished whether micropipes exhibit line-shaped depression or not by using mirror electron microscope observation as high-resolution inspection. The accuracy of the distinction results is confirmed by scanning electron microscope observation, and electrical characteristics of the P–N diode are fabricated using the inspected wafer. Furthermore, the sub-micrometer-sized micropipes are observed at the sites of leakage current identified by emission microscopy. Additionally, device simulation of the blocking-voltage characteristics of P–N diodes suggests that the increase in leakage current depends on the electric field at the sub-micrometer-sized micropipes, regardless of their core size. [ABSTRACT FROM AUTHOR]

Gastropods forage with their radula, a thin chitinous membrane with embedded teeth, which scratch across the substrate to lose food particles. During this interaction, the risk of loosening particles is obvious without having a specialized mechanism holding them on the tooth surface. As mucus secretions are essential in molluscan life cycles and the locomotion and attachment gels are known to have an instant high adhesion, we have hypothesized that the saliva could support particle retention during feeding. As adhesion of snail saliva was not studied before, we present here an experimental setup to test its particle-binding capacity using a large land snail (Lissachatina fulica, Stylommatophora, Heterobranchia). This experiment was also applied to the gels produced by the snail foot for comparison and can be potentially applied to various fluids present at a small volume in the future. We found, that the saliva has high particle retention capacity that is comparable to the foot glue of the snail. To gain some insight into the properties of the saliva, we additionally studied it in the scanning electron microscope, estimated its viscosity in a de-wetting experiment, and investigated its elemental composition using energy dispersive X-ray spectroscopy reveling higher contents of Ca, Zn and other potential cross-linkers similar to those found in the glue. [ABSTRACT FROM AUTHOR]

In recent years, precision and accuracy for a more precise critical dimension (CD) control have been required in CD measurement technology. CD distortion between the measurement by a critical dimension scanning electron microscope (CD-SEM) and a reference tool is the most important factor for a more accurate CD measurement. CD bias varies by a CD-SEM and a pattern condition. Therefore, it is urgently needed to identify, characterize, and quantify those parameters that may or may not affect the CD measurement by a CD-SEM. The sensitivity of the Monte Carlo simulated CD-SEM images with multiple physical modeling components has been studied previously. In this study, we demonstrate that the work function and elastic scattering potential models have a significant impact on secondary electron emission intensity, but their influence on the shape of the linescan profile is small, and other factors like the optical energy loss function and dielectric function models have even smaller effects. We have evaluated the uncertainty in the linescan profiles of Si line structures with different sidewall angles due to several different physical factors. It is found that when the CD is evaluated by a peak/valley method, the uncertainty of the CD is negligible. Therefore, it is concluded that the CD value and its related uncertainty are not critically related to the physical factors of the present Monte Carlo simulation model but rely dominantly on the line structure and electron beam parameters. [ABSTRACT FROM AUTHOR]

We report on the metrological characterization of the emission from a germanium-vacancy center in diamond under a microfabricated solid immersion lens in a confocal laser-scanning microscope setup. Ge ions were implanted into a synthetic diamond at 3 MeV, and germanium-vacancy centers were then formed by subsequent annealing. Afterward, solid immersion lenses were fabricated in a focused ion beam scanning electron microscope. The photoluminescence was investigated at room temperature in terms of the spectral distribution, the excited state lifetime, the second-order correlation function, and the saturation behavior, proving simultaneous high single-photon purity and high brightness. Two methods were exploited to minimize the residual multi-photon probability: spectral filtering and temporal filtering. According to these results, we assume that Raman scattered photons and emission from neighboring color centers play an important role in the residual multi-photon emission probability. The system efficiency of the single-photon source was investigated and found to be in accordance with the value calculated from all sources of loss in the setup. The branching ratio of the germanium-vacancy center for the decay into the ground state and into metastable state was calculated. The results enable the usage of the single-photon source in future quantum radiometric experiments. [ABSTRACT FROM AUTHOR]

Because of their full compatibility with CMOS technology, HfO2-based ferroelectrics, and especially Hf0.5Zr0.5O2 (HZO), attract a lot of attention. However, the overwhelming majority of measurement techniques provides only information about the cumulative electrical response of many domains of HZO, i.e., at the macroscopic level. So far, only piezoresponse force microscopy technique was applied to visualize distinct ferroelectric domains in HZO and to analyze the local switching behavior in the microscopic level. This work introduces the possibility of using electron beam-induced current (EBIC) technique in the scanning electron microscope to visualize the gradual polarization reversal of HZO and to obtain the local polarization dynamics. We show that although the local EBIC signal is affected by surrounding domains, studying the variations in the ferroelectric response of individual domains as well as the spread of the local stiffness and local imprint is possible by this method. Besides, we show the connection between the EBIC current and an electric field across passive non-ferroelectric layers at interfaces between HZO and metal electrodes, which opens up additional opportunities to use the EBIC technique for investigations of interface-dependent properties of HZO ferroelectrics in the future. [ABSTRACT FROM AUTHOR]

Inspired by the strong adhesion of mussels, basalt fibers (BFs) were modified with polydopamine and then composited with nylon 6. The effect of polydopamine content on the interfacial interactions and mechanical properties of the composites was investigated. In addition, silica nanoparticles were grown on the surface of polydopamine‐modified BFs to investigate the synergistic effect. The study revealed that the mechanical properties of the composites based on polydopamine‐modified BF were gradually enhanced with the increase of the dopamine coverage concentration, and gradually decreased after reaching the peak. 0.5 g/L concentration of dopamine solution modified BFs showed the best enhancement effect on nylon 6, and its tensile strength could reach 133.1 MPa, which was 28.5% higher than that of the unmodified composites. The tensile strength of the composites modified with both dopamine and silica nanoparticles reached 157 MPa, which was 51.7% higher than that of the unmodified composites. In addition, scanning electron microscope images of fracture sections confirmed the strong interfacial interaction between BF and PA6. Highlights: The surface roughness of BF was increased by nano‐SiO2.Hydrogen bonding was formed between PDA and PA6.Physical interlock was formed between nano‐SiO2 and PA6.Tensile strength increased by 51.7% with both nano‐SiO2 and PDA.Stronger interfacial interaction leads to higher thermal stability. [ABSTRACT FROM AUTHOR]

The thixomolding technology offers distinct advantages for producing magnesium matrix composites with intricate geometries. This study explores the effects of incorporating hybrid SiC–Al2O3 particles on the microstructure, deformation, fracture, and mechanical properties of a thixomolded Mg–10Zn alloy. The composite exhibits a homogeneous distribution of Al2O3 and SiC particles within the matrix. The addition of SiC–Al2O3 reinforcements helps reduce the content of primary α -Mg solid and refine the microstructure. The composite demonstrates a yield strength of 186 MPa, an elastic modulus of 48.6 GPa, and a respectable elongation of 6.8%. The digital image correlation measurement was performed at the sample scale, unveiling overall deformation characteristics. Crystal plasticity finite element method was employed for high-fidelity microstructure, showcasing mesoscale deformation feature such as the deformation mechanism of grains adjacent to reinforcements. It was found that SiC–Al2O3 particles prevent the formation of large shear band, benefiting the ductility of the material. The post-mortem analysis using scanning electron microscope near the fracture position reveals micro-cracks inside the SiC particles. Notably, the SiC/Mg interface shows no signs of cracking, while some Al2O3/Mg interfaces are separated. Reinforcement cracking is correlated to the stress it withstands, and the mesoscale deformation analysis reveals that the reinforcement stress is increased when non-basal slip in grains adjacent to the reinforcement becomes difficult to be activated. This work serves as an example for developing Mg matrix composites through the thixomolding process. The findings of this study provide valuable insights for the design of high-performance thixomolded Mg-based composites [ABSTRACT FROM AUTHOR]

Phosphoric acid-based geopolymer (PGEO) belongs to acidic material and has many applications in environmental disposal. The curing method has an important impact on the mechanic performance of geopolymers, the existing research concerning PGEO synthesized from fly ash (FA) and phosphoric acid (PA) are performed on the specimens cured at sealed environment, but no related research on the PGEO cured at an open environment is found. Therefore, to investigate the mechanic performance, pH and of PGEO cured in an open environment, the unconfined compressive strength tests were conducted on PGEO specimens cured in an open environment, and its mechanism was investigated using Scanning Electron Microscope, X-Ray diffraction, and Fourier transform infrared reflection (FTIR) tests. Moreover, the thermogravimetric was measured using the thermogravimetric tests. The results showed that in the scope of this study, the compressive strength of the PGEO decreased with the PA concentration and the liquid–solid ratio (L/S) increasing. When the L/S was a fixed value, as the curing time increased, an obvious strength loss was observed for the PGEO with the content of 40 and 50%, but the compressive strength increased first and then, reduced for the PGEO with the content of 40 and 50%, a maximum strength was obtained at 60 days of curing. The open curing for the PGEO is not conducive to the later growth of compressive strength. As the PA concentration and L/S increased, the pH descended. As the curing time lengthened, the pH first raised and then droped, the maximum pH was obtained at 60 days. Furthermore, the compressive strength increased with the pH with a good correlation. The microscopic analysis showed that the crystalline compounds AlSiP3, Ca2P2O7(H2O)2, molecular sieve SAPO-20 (Al0.47Si0.13P0.4)O2, AlPO4-5 (AlPO4), CaHPO4, and AlPO4 in PGEO were detected. Overall, the open curing environment is not conducive to PGEO, and sealed curing should be used in engineering applications. [ABSTRACT FROM AUTHOR]

In this present investigation, novel hybrid magnesium composites were synthesized by the inclusion of self-lubricating (BN/MoS 2) and ceramic (ZrO 2) particulates with the help of the powder metallurgy technique. ZE41 magnesium (Mg–4Zn-1RE-0.7Zr) was applied for a broad range of components, including the gearbox casing, the framework of the door, and transmission in aircraft like the Sikorsky UH-60 and the Boeing 727. Apart from its structural application, its usage was limited because of its deficient wear and mechanical properties. This research focuses on enhancing the potential applications of the ZE41 magnesium alloy by improving its mechanical and tribological characteristics. The design of the experiment scheme was applied to explore the effect of individual reinforcements and their synergistic effects on various properties of prepared composites. Microstructural inspection was employed to inspect the morphological characteristics of prepared specimens through scanning electron microscope (SEM) and Energy-dispersive X-ray spectroscopy (EDS) and X-ray diffraction analysis (XRD). By analysing SEM, EDS, and X-ray diffraction patterns, the microstructural evaluation reveals uniform phase dispersion and the existence of reinforcements with some minor defects. As a result of the inclusion of reinforcements in composites, the hardness of the reinforced specimen improved to 39.65%, while the wear rate of the reinforced specimen decreased to 40.90% compared with monolithic alloy. A multi-objective grey relational analysis (GRA) optimization method was used to perform a detailed tribological analysis on Specimen G (ZE41 mg + 3% ZrO 2 + 3% MoS 2). According to the results of GRA, the optimized rate of wear and frictional coefficient were achieved on sliding velocity (4 ms−1), sliding distance (2000 m), and load (10 N). The worn surface micrograph reveals that the reinforced composite underwent abrasion and delamination wear, while the unreinforced alloy experienced plastic deformation. [ABSTRACT FROM AUTHOR]

In recent years, the number of studies focusing on the additive manufacturing has increased seriously to elucidate the critical points such as physical, chemical, and mechanical properties. Contrary to common trends and for the first time in the literature, this experimental endeavor aims to comprehend the combined impact of reinforcement type and heat treatment on the wear features of additively manufactured polyamide 6 (PA6) composites. As reinforcement materials, glass, and carbon fibers were utilized and all samples were created through the fused filament fabrication. Half of the samples were subjected to annealing treatment after the main production, and characterization works were performed using a fused emission scanning electron microscope, differential scanning calorimetry, and dynamic mechanic analysis. From the outcomes, it is seen that heat treatment has a positive effect on the hardness, and wear resistance of the composites. Besides, glass fiber‐reinforced samples display lower friction coefficient and lower volume loss results than other samples. For all samples, secondary annealing causes a positive impact on wear endurance in most cases. On the other side, the wear mechanism of the tested samples changes with the test force level and reinforcement type. At lower test forces, abrasive wear‐induced debris parts are detected on the deformed surfaces of PA6 and carbon‐added samples, but this case is opposite for the highest force of 40 N. Highlights: Additive manufacturing was underlined as a promising way to create polymer composites with high dimensional accuracy.The combined effect of secondary annealing and reinforcement type on the wear resistance of 3D‐printed PA6 composites was examined for the first time in the literature.Carbon and glass fibers were compared to explore their effect on friction coefficient and wear behavior of polymer composite samples produced via FFF technology.Hardness and surface roughness measurements were used to comprehend the dry sliding wear results.Depending on the increasing test force levels and reinforcement type, deformation, and abrasion mechanisms were analyzed. [ABSTRACT FROM AUTHOR]

In this work, 2D ferromagnetic M3GeTe2 (MGT, M = Ni/Fe) nanosheets with rich atomic Te vacancies (2D‐MGTv) are demonstrated as efficient OER electrocatalyst via a general mechanical exfoliation strategy. X‐ray absorption spectra (XAS) and scanning transmission electron microscope (STEM) results validate the dominant presence of metal‐O moieties and rich Te vacancies, respectively. The formed Te vacancies are active for the adsorption of OH* and O* species while the metal‐O moieties promote the O* and OOH* adsorption, contributing synergistically to the faster oxygen evolution kinetics. Consequently, 2D‐Ni3GeTe2v exhibits superior OER activity with only 370 mV overpotential to reach the current density of 100 mA cm−2 and turnover frequency (TOF) value of 101.6 s−1 at the overpotential of 200 mV in alkaline media. Furthermore, a 2D‐Ni3GeTe2v‐based anion‐exchange membrane (AEM) water electrolysis cell (1 cm2) delivers a current density of 1.02 and 1.32 A cm−2 at the voltage of 3 V feeding with 0.1 and 1 m KOH solution, respectively. The demonstrated metal‐O coordination with abundant atomic vacancies for ferromagnetic M3GeTe2 and the easily extended preparation strategy would enlighten the rational design and fabrication of other ferromagnetic materials for wider electrocatalytic applications. [ABSTRACT FROM AUTHOR]

Silicon carbide fiber reinforced silicon carbide ceramic matrix composite (CMC SiC f /SiC) has the advantages of high temperature resistance, corrosion resistance, high strength, low density, and oxidation resistance. It is a high-performance advanced material in aerospace, energy and other fields. However, due to its high hardness, brittleness and anisotropy of fiber structure, the research on application-oriented high-quality processing technology has become a hot issue. In this paper, a new process of rotational thirteen-beam coupling nanosecond laser processing of CMC-SiC f /SiC was studied. The rotational thirteen-beam coupling ablation experiments were carried out on CMC-SiC f /SiC workpiece. A laser beam is divided into thirteen beams and rotated around the beam center by using a beam splitter element. The morphology, structure and composition of ablation holes at different speeds were observed and analyzed by laser confocal microscope, scanning electron microscope, and X-ray energy dispersive spectrometer. It is found that the characteristics of rotational beam coupling have a significant effect on the laser ablation morphologies. The results show that the ablation region of CMC-SiC f /SiC is elliptical due to the fast heat transfer of fibers. The energy density distribution of the waist section of the Gaussian like beam after beam coupling is similar to the "W" shape, and the central energy is lower than the surrounding energy, and the ablation holes also show a similar "W" shape. With the increase of rotational speed, the hole depth first decreased and then increased, the hole diameter and roundness first increased and then decreased, and the hole section was "W" shaped. The ablation area can be divided into five parts: the white granular SiO 2 solid coverage area, the recast layer, the lower recast layer, the molten layer, and the heat affected zone. The rotational characteristics will make the reaction intensity of the whole ablation area more uniform in the circumferential direction. The formation mechanism and element distribution of each part were explored. The research work in this paper will provide a new technical way for the high-performance application of CMC-SiC f /SiC. [ABSTRACT FROM AUTHOR]

The effectiveness of silicon carbide (SiC) planarization mostly relies on the chemical and mechanical effects during chemical mechanical polishing (CMP). Nevertheless, the alumina (Al 2 O 3) abrasive only provides a mechanical effect and is incapable of achieving a high-efficiency polishing of SiC. To address this issue, a series of novel Al 2 O 3 @MnO 2 composite abrasives were prepared by encapsulating varying amounts of manganese dioxide (MnO 2) on Al 2 O 3 abrasive, and the polishing performance on SiC wafers was evaluated. The X-ray diffraction (XRD) and scanning electron microscope (SEM) images, along with the size and zeta potential data, show that MnO 2 is successfully coated on the surface of Al 2 O 3 , and the dispersion of Al 2 O 3 @MnO 2 composite abrasive is significantly improved when compared with the pure Al 2 O 3. Furthermore, the CMP experiment and surface profile analysis demonstrate that the material removal rate (MRR) can reach a maximum value of 640.47 nm/h when using a 0.05 wt% MnO 2 -coated Al 2 O 3 composite abrasive, which is 76 % higher than that of traditional Al 2 O 3 abrasive. Furthermore, the average surface roughness (Sa, arithmetic mean height) of SiC is reduced to 0.73 nm. X-ray photoelectron spectroscopy results reveal that the surface of SiC is oxidized and forms a chemical bond known as Mn–O–Si after CMP. The results of the friction coefficient test and contact angle test indicate that slurries containing composite abrasive have exceptional wettability and a higher friction coefficient. Under the synergistic chemical and mechanical effects, SiC is oxidized to soft oxide and then removed circularly to reach excellent flatness. [ABSTRACT FROM AUTHOR]

The current research article has investigated the synthesis and characterization of novel iron nanoparticles (INPs) from neem and betel leaves extract combination using response surface methodology–central composite design and coated with chitosan–curcumin (CCINPs) as a biocompatible and contrast agent for magnetic resonance imaging (MRI). The coating of INPs with chitosan and curcumin (CCINPs) was carried out using a simple, easy, chemical‐free ultrasonication method and characteristics were confirmed by UV–visible (Vis) spectrophotometer (UV–Vis), Fourier‐transform infrared spectroscopy, X‐ray diffraction, scanning electron microscope, atomic force microscopy, and vibrating sample magnetometer. The biocompatibility of the particles was ensured by conducting hemolytic and cell viability assays. The nanoparticle was found to be nonhemolytic (<5%) up to 150 μg/mL for both INPs and CCINPs. The cell viability was stable (peripheral blood mononuclear cells‐PBMCs) till 48 h at 150 μg/mL of INPs and CCINPs. Both the test results produced were found to be biocompatible and additionally, an in vitro MRI study of INPs and CCINPs demonstrated the efficiency of the nanoparticle as a negative contrast agent with enhanced contrast nature in CCINPs. Thus, overall results indicate that the green synthesized chemical‐free novel CCINPs could be a potential candidate for a wide range of applications such as MRI, drug delivery, and in magnetic fluid hyperthermia. [ABSTRACT FROM AUTHOR]

Wastewater from the textile and dyeing industries contains hazardous dyes. This study aims to determine the effectiveness of magnetic biochar nanocomposites synthesized from khat leftovers (KLs) and coffee husks (CHs) in removing methylene blue (MB) from wastewater. Magnetic biochar nanocomposites were synthesized by pretreating 25 g of biomass with a 12.5 mmol mixture of FeS and FeCl3 at a 1:1 molar ratio, followed by pyrolyzing at 300°C for 1 h. The resulting products were analyzed using X‐ray diffraction, Fourier transform infrared, scanning electron microscope, and Brunauer‐Emmett‐Teller. The results showed that the adsorbents are amorphous, and the activated biochars, are more porous and contain various functional groups such as C‐O, C = C, O‐H, C‐H, and Fe‐O. When 0.2 g of pristine biochars of CH and KL were applied to 20 mL aqueous solutions containing 20 mg/L of MB at pH 7.5 and 25°C, they removed 44.73% and 75.26% of MB, respectively. However, the resulting nanocomposites exhibited a maximum removal efficiency of 99.10% and 99.23% with magnetic iron oxide‐CH biochar nanocomposite (Fe3O4‐CHBNC) and magnetic iron oxide‐KL biochar nanocomposite (Fe3O4‐KLBNC), respectively, with maximum adsorption capacities of 51.02 and 78.13 mg/g. The reusability study also showed removal efficiencies of 77.57% and 83.49% up to six‐cycle reuse. [ABSTRACT FROM AUTHOR]

Pore‐throat structure is a key factor that influences the storage and fluid flow capacity of tight sandstone reservoirs. Taking the tight sandstone reservoir of Xu2 Fm in Zhongba area as an example, the reservoir quality, pore‐throat type and pore size distribution of tight sandstone in the study area were described by casting thin section, scanning electron microscope and high‐pressure mercury injection test. In order to quantitatively characterize the complexity and heterogeneity of pore‐throat structure, fractal analysis was performed using mercury saturation and pore size data. This study mainly reveals the relationship between the geometric shape characteristics and fractal dimension of the binary pore structure of ultra‐low permeability tight sandstone and clarifies the influence of different scale pore throats on reservoir physical properties. The results indicate that the physical properties of the reservoir in the study area are poor, the pores are mainly intergranular pores and dissolution pores, the throat is flake and necked and the pore size distribution range is large. The fractal curve obtained by the mercury saturation method shows a significant turning point, and the pore‐throat system is divided into two types: small‐scale and large‐scale. The fractal dimension of large‐scale pore throat is greater than the three‐dimensional Euclidean space dimension, which does not conform to the fractal theory. The fractal dimension of small‐scale pore throat is closely related to the pore‐throat structure and has obvious fractal characteristics. The geometric shape of binary pore‐throat structure in tight sandstone is the main factor affecting the difference of fractal dimension. The development of small pores in sandstone is positively correlated with the total porosity, but its contribution to permeability is relatively low. The physical properties of tight sandstone are mainly controlled by the development degree of large‐scale pore throat. [ABSTRACT FROM AUTHOR]

This study takes the tight sandstone of the lower sub‐member of the first member of the Eocene Shahejie Formation (Es1x) in the Suning area, Raoyang Sag, Bohai Bay Basin. Furthermore, it determines the rock type of the middle‐deep tight sandstone through lithologic profiling, core observation and log data analysis. The genetic control factors of tight sandstone in the study area are analysed using conventional thin section, pore‐casted thin section and scanning electron microscope, and the characteristics and genetic control factors of tight sandstone reservoirs are summarized. The research results show that the tight sandstones in this area are primarily feldspathic sandstone and feldspathic lithic sandstone, with high quartz contents, around 61.50%. The average porosity of the reservoir in the study area is 4.69%, and the average permeability is 2.92 mD, which are characteristics of low‐porosity and low‐permeability reservoirs. Through research, it has been found that the distribution of sedimentary facies and diagenesis in the study area control the development and distribution of 'sweet spots'. Both compaction and cementation reduce the physical properties of the reservoir, while dissolution can increase porosity, thereby increasing the physical properties of the reservoir; dissolution resulted in an increase of approximately 3.57%–3.69% in the porosity of the tight reservoir in the study area, with an average porosity increase of 3.63%, and is the main controlling factor for the development of 'sweet spots' in the reservoir. The results provide an important basis for guiding the exploration and development of tight sandstone oil and gas in the lower sub‐member of the first member of the Eocene Shahejie Formation (Es1x)in the Suning area. [ABSTRACT FROM AUTHOR]

The dissolution mechanism of phases c‐Ti0.5Al0.5N, c‐aluminium nitride (AlN), c‐TiN, and Al2Ti, and elements of the Ti1–xAlxN coatings (for x < 0.6) in 3 wt.% NaCl solution is described based on the results of X‐ray diffraction analysis, energy‐dispersive X‐ray spectroscopy, and scanning electron microscope and previous electrochemical tests. Researchers studied the protective effectiveness of Ti1–xAlxN coatings in 3 wt.% NaCl solution by analyzing the factors: composition, thickness, porosity, total energy of ground state, stresses, structure, and texture. It was first established that the additional c‐TiN phase with Rpmax and Ecormax, and secondary phase Ti0.70–0.82N formed after Al's dissolution in the main phase c‐Ti0.5Al0.5N increases the N content and prevents the Ti dissolution in the Ti1–xAlxN coatings. The phase c‐AlN with icormin reduces the dissolution rate of Al in the c‐Ti0.5Al0.5N phase. The stoichiometric c‐Ti0.5Al0.5N is the most thermodynamically stable phase. The described phase transformations in Ti1–xAlxN coatings during phases dissolution in 3 wt.% NaCl can predict the coating protective effect. A multilayer coating with layers of c‐AlN, c‐TiN, and c‐Ti0.5Al0.5N is recommended for industrial use. [ABSTRACT FROM AUTHOR]

The effects of different quenching methods on the microstructure and mechanical properties of 30MnB5NbTi hot stamping steel are investigated, and the quenched microstructure is characterized by scanning electron microscope (SEM), electron backscatter diffraction (EBSD), and transmission electron microscopy (TEM). The mechanical properties are evaluated by uniaxial tensile test. The results reveal that, in comparison to die quenching, oil quenching, or air cooling, water‐quenched samples (tempered after water quenching, die quenching and oil quenching) exhibit the highest ultimate tensile strength (UTS) and yield strength (YS), reaching 2052 and 1422 MPa, respectively. Various quenching methods enable multi‐level strength control for the same steel grade, achieving a strength control range of ≈1000 MPa. The microstructure of samples quenched by water, die, and oil is fully martensite, and martensite exhibited block and lath morphology. With the increase of cooling rate, martensite laths become finer and the prior austenite size decreased. The microstructure of air‐cooled samples is martensite, ferrite, and retained austenite. The strengthening mechanisms of different quenched samples are calculated. The results show that dislocation strengthening and precipitation strengthening are the two dominant strengthening mechanisms in 30MnB5NbTi hot stamping steel. Therefore, the properties of hot stamping steel can be improved by changing the cooling rate by designing physical dies. [ABSTRACT FROM AUTHOR]

The development of the industry has increased the demand for energy storage, making the provision of energy storage devices essential. The supercapacitor is one of the potential energy storage devices, and carbon aerogel (CA) is a promising candidate for supercapacitor electrode fabrication. Ni-doped nipa palm shell-derived CA (Ni-NS-CA) was used to fabricate the electrode for supercapacitors to save production costs and utilize biomass wastes. Ni-NS-CA was synthesized via a three-step process: Hydrogel making through cross-linking (SA, Ni2+), freeze-drying, and pyrolysis. The characteristics of Ni-NS-CA are analyzed using a scanning electron microscope, field-emission scanning electron microscopy, energy-dispersive X-ray spectroscopy, X-ray diffraction, Raman spectroscopy, and Nitrogen adsorption–desorption isotherm 77 K. The electrochemical properties of Ni-NS-CA was analyzed via cyclic voltammetry, galvanostatic charge–discharge, and electrochemical impedance spectroscopy. With stable energy storage results (104.15 F g−1) and the electrochemical system based on Ni-NS-CA extends its application to Hg2+ sensing. Moreover, Ni-NS-CA was a potential material to solve oil spills, which has an oil adsorption capacity of 31.24 g g−1. [ABSTRACT FROM AUTHOR]

Cracks generated in sheet coating of water-based slurries are an increasingly important concern in the development of diverse material science, such as fine ceramics, Pt catalysts, and Li transition metal oxides, from an environmental safety perspective. However, a comprehensive understanding of crack formation remains elusive due to the intricately entangled interplay among various characteristics of slurries. Here, we systematically ascertain the causes at work in crack initiation by analyzing the physical parameters of a series of aqueous alumina slurries using machine learning. The analysis reveals a strong correlation between rheological hysteresis and sheet cracking. As a verification of the correlation, the crack suppression by controlling the rheological hysteresis is experimentally confirmed. Furthermore, we visualize the microstructure in the slurry that induces cracks with a liquid-phase scanning electron microscope, clarifying the rheological dynamics. These results disentangle that rheological hysteresis is a good indicator directly reflecting microstructural durability against drying stress. [Display omitted] [ABSTRACT FROM AUTHOR]