Search

This paper aimed to determine the characteristics of physical and mechanical properties of rice straw hand sheet and investigated the optimal conditions for making rice straw paper. The chemical composition of rice straw determined with the TAPPI standards. The conditions of making paper hand sheet composed of pulping time: 2 hours, 4 hours, pulping temperature: 100°C, 130°C, pulping solvent: 2 wt% NaOH, 4 wt% NaOH and bleaching: unbleached pulp, bleached pulp with 2% H2O2. The paper hand sheet was tested based on TAPPI methods, basic weight TAPPI- T410-om-93, thickness TAPPI- T411-om-89, moisture content TAPPI- T412-om-93, brightness TAPPI T452 om-92, opacity TAPPI standard T 425 om-91, burst strength TAPPI T403 om-97, tensile strength TAPPI T494 om-01, and tear strength TAPPI-T414-om-88. The results showed that the optimal conditions of rice straw hand sheet including pulping time: 2 hours, pulping temperature: 100°C, pulping solvent: 2 wt% NaOH, and bleaching: unbleached pulp gave the highest the physical and mechanical properties form other conditions. This conditions showed as the basic weight 62.27 g/m2, thickness 259.30 µ, opacity 93.34 ISO%, burst strength 64.75 kPa.m2/g, tensile strength 95.33 N.m/g, and tear strength 473.55mN.m2/g. In this condition, the paper hand sheet used at the lowest concentration of pulping solvent and non-bleached, which reduces environmental pollution.

Anode surface plays important role for extracellular electron transfer (EET) of exoelectrogenic microbes in microbial fuel cell (MFC). In this report, the electrochemical performance of a TiO2nanorod array modified carbon paper electrode (TiO2NRs/CP) is greatly improved by controlled chemical etching process. The etching process keeps the array morphology but yields obvious hollows on tops of TiO2nanorods. The etched electrode (TiO2NRs-HOT/CP) exhibits better hydrophilicity than carbon paper (CP) and TiO2NRs/CP electrode as seen from smaller contact angle (CA) and more attached microbes S.loihica PV-4. Meanwhile, the hollows allow higher local concentration of microbial self-secreted flavins that can act as electron mediators for interfacial electron transfer of PV-4 through in-direct pathway. Accordingly, PV-4 produces larger current density at TiO2NRs-HOT/CP electrode with maximum current density of 0.038 mA cm–2, which was much higher than that at CP electrode, and almost five times higher than that at un-etched TiO2NRs/CP electrode.

In this study, 12 commercially available paper towels were collected from the local market. Their tensile properties were investigated by Kawabata Evaluation System for Fabric (KES-F). Four tensile properties namely: (i) extensibility (EMT), (ii) tensile energy (WT), (iii) tensile resilience (RT) and (iv) linearity of WT (LT) were evaluated. Experimental results revealed that the tensile properties varied within the products. EMT was used as the key property for discussing the tensile properties of paper towels. However, when the different tensile properties were correlated, it was found that WT/RT, WT/EMT and RT/EMT had strong Pearson correlation. In addition, there was no significant statistically relationship between weight and thickness to EMT. Based on this study, it can provide some information about the tensile properties of paper towels in local market which may help the industry for further improving the product quality.

12 commercially available paper towels were collected from the local market and studied in this paper. Kawabata Evaluation System for Fabric (KES-F) was used for evaluating their bending properties. Two bending properties namely: (i) bending rigidity (B) and (ii) bending moment (2HB) were evaluated. Experimental results indciated that the bending properties varied within the products. B was used as the key property for discussing the bending properties of paper towels. When the correlations of different bending properties were investigated, it was found that no significant was found between B and 2HB. However, there was significant statistically relationship between weight and B but no relationship between thickness and B. With the use of the results, the product developer could improve the bending properties of the paper towels.

In this study, 12 commercially available paper towels were collected from the market. Their shearing properties were evaluated by Kawabata Evaluation System for Fabric (KES-F). Three properties namely: (i) coefficient of friction (MIU), (ii) deviation of MIU (MMD) and (iii) geometric roughness (SMD). Experimental results revealed that the surface properties varied within the products. When different properties were correlated, it was found that there was not significantly relationship between MIU, MMD and SMD. However, weight and thickness had well statistically relationship to SMD.

As a kind of environmentally friendly material, microfibrillated cellulose (MFC) has the following advantages: renewable raw materials, easy recycling, biodegradable, safety and so on. It can be combined with antibacterial agents to prepare the antibacterial packing materials for food. In this paper, the nano-ZnO was modified by titanate coupling agent TM-38s at first,determines the best dosage of TM-38 is 3% in the modification process,the dosage of the isopropyl alcohol for 40ml,improving its dispersibility. And then added in the MFC suspension to formulate the antibacterial coating for antibacterial coated paper preparation. The changes of antibacterial properties of the paper before and after coating were investigated in this study. The results showed that the paper had a significant antibacterial activity to e. coli and staphylococcus aureus (the antibacterial circle was bigger than 15 mm).When the nano-ZnO dosage was 2.5wt%, the antibacterial properties of the coated paper could reach the best situation. Application of the antibacterial caoated paper to the food packaging could restrain and kill the microorganisms on the food surface effectively, prolong the shelf life of food, and improve the food safety.

In this paper, the stiffness and folding endurance of the paper were investigated with three kinds of pulp, such as the mechanical wood pulp, chemical pulp and composite pulp, after using common additives and cleaning additives. The results indicated that the stiffness of the paper can be increased by 20% ~ 30% and folding endurance can improve 20% ~ 60% after using new kind of cleaning additives no matter what kind of filler. New cleaning additives can not only improve the physical properties of paper, but also change "acidic papermaking" of the traditional paper industry into clean neutral papermaking environment. Especially, it is suitable for the production of food card paper.

Noise pollution is a workplace hazard which causes loss of hearing, depending on the sound pressure level and duration of exposure. Because duration of exposure is usually uncontrollable, sound absorbers are used to reduce the value of sound pressure level. A common method to reduce noise is to use porous sound absorbers made out of mineral wools or glass fibres. However, these materials pose health risks and are non-recyclable. This project aimed to fabricate a sound absorber using recycled paper which is in the form of egg cartons as an alternative to the abovementioned fibres. Paper fibres posses high fibre porosity and can be manufactured in a manner which the properties can be easily controlled, making them ideal to be made into sound absorbers. Furthermore, they are biodegradable, do not pose health risks and can be manufactured into different shapes easily. Recycled paper was first turned into pulp, blended and poured into moulds. Different amounts of pulp was compressed until the sample size was approximately 20 mm thick and then dried in a furnace dryer at 600C for 12 hours. The samples were tested using a two-microphone, transfer function impedance tubes according to the ISO 10534-2 standard. Its porosity was determined using a modified wash basin method. The results indicate that the optimum panel has an average noise reduction coefficient, (NRC) of 0.50, which qualifies it to be used as a sound absorbing material. It also encounters its maximum value of 0.98 which occurred at the 1575-1675 Hz range. When compared to other materials, recycled paper has similar properties as coir fibre and is quite comparable to other commercial sound absorbers at the same thickness.

The influence of coating layer structure on both physical and printing quality of the paper was studied. Different coating layers were obtained by changing the ratio of polyvinyl alcohol adhesives and silicon dioxide pigments in the coating formula. Then the structure, physical properties and ink-jet printing performance of the coated paper were measured. The influences of coating structure on physical properties and ink-jet printing performance were evaluated. The results showed that as the ratio of adhesive increased, the coating porosity decreased; the average pore diameter increased at first and then decreased, but in general tended to decrease; the initial drop contact angle increased, which testified the stronger hydrophobicity of the coated surface with higher adhesive ratio. The average pore diameter has a negative linear correlation with paper roughness while has a positive linear correlation with air permeability. The larger the average pore diameter, the greater the density values, as well as the better tone reproduction and the larger color gamut range. Average pore diameter also has a weak correlation with dot area and dot roundness.

This research is about an attempt to evaluate the effect of water contents towards the packaging properties of paper made from coconut coir, which was being processed manually through beating times method. The purpose of this investigation is to relate the composition of coconut fibre and water content with the tensile strength and tear factor. The composition starts from sample A, which has 90% of water and 10% of coconut fibre. The sample continues with 10% decreasing content of water and 10% increment of coconut coir. Base on tensile test and tear test results, graphs were plotted and it shows sample D, with 60% of water and 40% of coconut coir has produced the highest tensile strength, breaking length and tensile index, with the value of 1020.6 N/m, 422.8 m and 4.1450 Nm/g respectively. On the other hand, sample A produced the highest tear factor, with the value of 92.7 g/mm2. As a conclusion, these packaging properties are good enough to become guidance in paper manufacturing industry, as well as to support the application of coconut coir fibre as an alternative packaging material in the future.

This paper describes the use of a printing circuit technology to generate hydrophilic channels in a filter paper. Pattern was first designed using Protel soft, and printed on a blank paper. Then, the pattern was transferred on a sheet copper using a thermal transfer printer. The sheet copper with pattern was dipped in a ferric trichloride solution to etch the whole pattern of the sheet copper. At last, the etched sheet copper was coated with paraffin, then with a filter paper and heated at the other side of the sheet copper with an electric iron. The melting paraffin penetrated full thickness of the filter paper and formed a hydrophobic “wall”. Colorimetric assays for the presence of protein and glucose were demonstrated in the paper-based device. The work is helpful for researching paper-based microfluidic devices for monitoring health and detecting disease.

Microfibrillated cellulose (MFC) was prepared from the bleached kraft hardwood pulp using TEMPO/NaClO/NaBr oxidation system and high pressure homogenization. By changing dosages of the TEMPO, NaClO and NaBr, the pressure and times of homogenization, pretreatment and homogenization process were optimized. Experimental investigation indicated that for making MFC of high quality, 0.25%TEMPO, 2.5%NaBr, 60%NaClO (based on oven dry pulp), 20 times of homogenization, pressure of 60MPa in the process of treatment were required. At last, the mechanical and barrier properties were tested after the base paper was coated by homemade MFC. The study suggested that mechanical properties (especially 5 times increase of the folding strength) increased substantially and air permeability decreased by 100times.

It is necessary to implement pretreatment operations for a paper based microfluidic device. A paper based microfluidic device with SAW driving microfluid has been implemented. Trance analyte to be detected was absorbed into a filter paper at first, and mounted on PDMS blocks on a piezoelectric substrate to ensure that the indicting filter paper has a little gap with the piezoelectric substrate. Reagents were then pipetted on the piezoelectric substrate and transported by surface acoustic wave excited by an interdigital transducer, which was fabricated on a 1280-yx LiNbO3 using micro-electrical technology. A color was developed due to chemical reaction, and the analyte concentration was evaluated by its grey value. Nitrate ion was detected using the microfluidic system.

Paper based printing plate is one of printing plates used in eight mo octave or specifically offset printing machine. In the printing process, the printed plate wants to keep its shape by the pressure, the friction and tension. It needs to have good dimensional stability and good ink-water balance of coating. This paper discusses the influence of different coating formulations and coating process on the mechanical properties of paper-based printing plate. In this paper, the wet strength of paper-based printing plate of different formulations and different coating amount were tested. The study provided the theoretical basis for ink-water balance coating formulations of paper-based printing plate and the plate production.

The waste corrugated paper was grinded to paper pulp first, and then the paper pulp was used to prepare the foamed waste paper pulp/high density polyethylene（HDPE）composites by compression molding with HDPE. The Rosand double-barrel capillary rhepmeter was used to research the influences of the blowing agent AC(Azodicarbonamide) content，waste paper pulp content，temperature and different blowing agent on the melt of the composites. Scanning electron microscopy（SEM）was also used to observe the effects of different contents of AC and waste paper pulp on the cell morphologies.The results showed that: when the shear rate up to 600 S-1，the melt performs of the foamed waste paper pulp/ HDPE composites were pseudoplastic flow, and turn up wall slip phenomenon. The viscosity of melt was significantly reduced with the content of AC increased, but it increased with the content of the waste paper pulp increased. When the shear rate reduced to 275 S-1 or below, the viscosity of melt reduced as the temperature riased; while when the shear rate went up to 275 S-1 or high, the viscosity of melt increased as the temperature riased. When the shear rate reduced to 325 S-1 or below, the melt of endothermic blowing agent （NaHCO3）showed the highest viscosity; when the shear rate went up to 325 S-1 or high, the melt of exothermic blowing agent AC shows the highest viscosity. The number of cell increased and size of cell became smaller with the AC content increased , but the number of cell reduced and the size of cell became larger with the content of waste paper pulp increased observing by SEM.

Impregnated paper for plywood formwork is an important material for the production of plywood formwork. It was developing with plywood formwork and the market had been expanding. Absorption and wet strength are main factors which can effects on the property of impregnated paper. In this paper, mechanical chemical pulp and waste paper were used to make special impregnated paper for formwork. The ratio of EMP, dosage of aid, and operation conditions were discussed. The result showed that the absorption was improved by increasing ratio of EMP, adding agent, drying quickly, and lighter pressure. A certain ratio of AOCC is necessary to ensure strength. The paper also discussed the difference of white spot between bamboo plywood formwork and plywood formwork which indicated that white spot caused by waste paper .However, it wasn’t damage the quality of structures.

Biopolymers have the potential to serve as coating materials for paper to improve its performance properties. The objectives of this study were to determine the effect of kelp coating on the physical properties of coated papers. It was found that kelp coated paper showed significant difference on physical properties, compared with uncoated. Kelp coated papers greatly increased in tensile strength. Paper coated with kelp solution can be used to produce packages with the potential to be used to maintain agricultural produce quality for the food industry, and may have other applications.

This paper draws on a roll coating method which used for the production of coated paper. Polylactide coating cardboard was prepared through the solvent coating, and study its packaging performance. In this study, chloroform is based solvent, ethanol or n-propanol as auxiliary solvents, poly (ethylene glycol) or poly caprolactone as plasticizer, and the water vapor permeability, oxygen permeability and heat sealability of polylactic acid coated cardboard.

It is usually reported that chitosan is used as paper strengthening agent. However, it is sorry that the study choosing chitosan which DD (degree of de-acetyl )and viscosity is filtered by experiments is blank. Many chitosan samples of wide viscosity range and wide DD range were tested by their strengthening effect on bleched wheat straw pulp. Then a few sample of chitosan is selected because of their obvious strengthening effect on pulp. This study could be as the foundation of further research of chitosan used as paper strengthening agent.

A new type of adsorbent which prepared with waste paper as raw material was applied in the treatment of dye wastewater, and studied the processing conditions on treatment effect. Batch adsorption study carried out as a function of the dosage, the stirring time, the stirring speed and the pH. The adsorption rate of newspaper adsorbent to basic blue dye simulated wastewater and alkaline yellow wastewater with an initial concentration of 80mg·L-1 can reach 98.56% and 92.23% at 4g·L-1 of the dosage of paper adsorbent, 15min of the stirring time and 150r·min-1of the stirring speed. The maximum adsorption were 233.1g·L-1 and 289.4g·L-1 respectively. The isothermal adsorption experiment was also studied and concluded that the adsorption equilibrium data fitted with the Langmuir isotherm. The characterization experiment showed that the modified paper adsorbent had stronger absorbability.

The aim of this work is to study the influence of beating and refining as well as the fibre furnish on the properties of silk paper, such as air permeance, softness, pore size, tensile index and burst index. The results showed that the beating characteristic of silk fibre was similar to that of plant fibre, they all had the characteristic of fibrillation. Silk paper had excellent softness and air permeance when the beating degree of silk pulp was 20 °SR, 181.3 μm/Pa·s and 2.5 mN·m2/g respectively, which was superior to paper made from plant fibres of the same beating degree. The minimum average pore size of silk paper was 5.11 μm at the beating degree of 20 °SR, and it decreased with the increase of beating degree, reached 0.79 μm at the beating degree of 67 °SR. With the increase of beating degree, the tensile index of silk paper increased at first, and then decreased. The burst index of silk paper showed a upward trend, but the softness and air permeance of it constantly decreased. The tensile strength of paper made from mixed-furnish pulp consisting of silk and softwood reached the maximum when the amount of silk fibre was 4%, and its air permeance increased with the increase of silk fibre.

Biocomposites sheets were prepared by compression molding from mixtures of corn starch plasticized by glycerol as matrix and cellulose fibers, extracted from used office paper, as reinforcement filler with contents ranging from 0 to 8% wt/wt of fibers to matrix. Properties of composites were determined by mechanical tensile test, differential scanning calorimetry, thermogravimetric analysis, water absorption measurement, and scanning electron microscopy. The results showed that higher fibers content raised the tensile strength and elastic modulus up to 109% and 112%, respectively, when compared to the non-reinforced thermoplastic starch (TPS). The addition of the fibers improved the thermal resistance and decreased the water absorption up to 63.6%. Scanning electron microscopy illustrated a good adhesion between matrix and fibers.

The novel flexible pressure sensor with skin-like stretchability and sensibility has attracted tremendous attention in academic and industrial world in recent years. And it also has demonstrated great potential in the applications of electronic skin and wearable devices. It is significant and challenging to develop a highly sensitive flexible pressure sensor with a simple, low energy consuming and low cost method. In this paper, the silver nanowires (AgNWs) as electrode material were synthesized by polyol process. The polydimethylsiloxane (PDMS) was chosen as a flexible substrate and polyimide (PI) film as dielectric layer. The AgNWs based electrode was prepared in two methods. One is coating the AgNWs on photographic paper followed by in situ PDMS curing. Another one is suction filtration of the AgNWs suspension followed by glass slide transfer and PDMS curing. Then the capacitive pressure sensor was packaged in a sandwich structure with two face to face electrodes and a PI film in the middle. The sensitivity of the sensor as well as the micro-structure of the electrodes was compared and studied. The results indicate that the roughness of the electrode based on AgNWs/PDMS micro-structure plays an important role in the sensitivity of sensor. The as-prepared flexible pressure sensor demonstrates high sensitivity of 0.65kPa-1. In addition, the fabrication method is simple, low energy consuming and low cost, which has great potential in the detection of pulse, heart rate, sound vibration and other tiny pressure.

Langmuir-Blodgett technique was applied to build optically homogeneous film of functionalized multi-walled carbon nanotubes (MWCNTs) on paper substrate. The palladium (Pd) nanoparticles were drop-casted onto MWCNTs network films before being exposed in hydrogen (H2) gas molecules environment under vacuum and atmospheric pressure at room temperature. The results demonstrate that the functionalized MWCNTs dispersed with Pd nanoparticles show good H2sensing response on paper substrate where the sensitivity of around 10 % was recorded at only 2 minutes exposure time.

Magnetic stripe cards and magnetic recording paper are commonly used in credit cards, identity cards, and transportation tickets. Barium ferrite was used to prepare magnetic inks and the magnetic ink was coated onto the paper substrate to obtain the magnetic papers. The crystal structure of barium ferrite was characterized by X-ray diffraction (XRD) and the magnetic property of barium ferrite was tested by vibrating sample magnetometer (VSM) The performance of the magnetic recording paper and the surface morphology of the coating magnetic layer were also characterized. The results show that the magnetic ink based on barium ferrite with the formula of 41wt% of the barium ferrite powder, 14wt% of polyurethane, 36wt% of solvent and 9wt% of PVP has good printing characteristics and the magnetic recording papers have good performance.

In order to investigate the influence of coating layer characteristics on the dynamic permeability and printing of ink-jet paper, coating was prepared by the precipitated calcium carbonate (PCC) and white latex used as bottom coating (recipe label:A,B),and coating formula was made by silica (SiO2) and polyvinyl alcohol used as surface coating (recipe label:a,b,c).Then paper were coated respectively on single bottom, single surface and multilayer. Then the dynamic permeability and printing of ink-jet paper were analyzed systematically. The results showed that whether single layer or multilayer, the values of Ct, Ci were minimum when the ration of pigment and adhesive was 70:30, because the hole diameter of the coating layer was smallest, and the absorption was strongest, so the dynamic permeability was best, and the ability of ink absorption was best, color density and tone reproducibility were best. It concluded that when the proportion of SiO2 and PVA was 70:30, the dynamic permeability and printing ability of ink-jet paper were relative better.

The bonding mechanism between water-based UV curable ink and active groups on paper’s fiber during curing process was studied in this paper. Low viscosity water-based UV-cured resin was synthesized by epoxy resins, epoxy diluent, acrylic acid and maleic anhydride in the presence of catalyst. The viscosity of the synthesis system and synthetic products were significantly reduced when epoxy diluent was added to replace parts of the epoxy resin. Epoxy diluent was very useful in reducing the viscosity of the product, but over-dose would have negative effects on the quality of the cured film. The water-based epoxy acrylate prepolymer was used as the substitution for the ink to investigate the binding mechanism between the active groups of prepolymer and fiber under UV irradiation. The prepolymer and photoinitiator were mixed and the mixture was diluted to an appropriate viscosity by a small amount of water, then printed on the paper by the method of analog printing and curred by UV curing machine. The printed paper was used to extract lignin by enzymatic/mild acidolysis. FT-IR was used to characterize the changes of the active groups in lignin. The results showed that the changes of active groups in lignin were founded in the existence of ultraviolet and photoinitiator, which consistent with the change of double bonds in prepolymer. The free radicals produced by photoinitiator in curing process not only promoted the double bonds to polymerize, but also accelerated the active groups of lignin binding. Experiments show that chemical bonds exist between them.

The experiment studied effects of paper on the height and glossiness of UV ink-jet 3D printing. The results showed that there all existed penetrations between the 1st ink layer and three kinds of paper, the bigger the roughness and bulk of paper were, the larger the penetration was, and penetration between the 1st ink and paper was obviously larger than that between two ink layers. Penetration between two ink layers was stable, almost not affected by paper. The bigger the roughness and bulk of paper were, the smaller the glossiness of ink layer was. There appeared directional ink strips on ink layer on three kinds of paper, beginning from the 3rd ink layer, there also appeared ink pits on ink layer on paper whose roughness and bulk were the biggest, which showed printer precision was also an important factor for the glossiness, apart from paper. Thus, the tight and smooth paper should be selected in UV ink-jet 3D printing. Before printing, pretreatment should be done to exclude the influence of the 1st ink layer and the ink strips.

The composite SiOx/polymer films are deposited as a top-coatings onto the paper substrates by radio frequency (RF) reactive magnetron co-sputtered two targets, silica and dicyclopentadiene dioxide cured with maleic anhydride (DCPD/MA).The samples prepared by changing PSiO2/PDCPD/MA, the ratio of RF powers density delivered to the individual target from 0.1 to 10 so as to prepare different SiOxcontent coatings. The wettability, mechanical properties, color reproduction printability, chemical characterization of the coatings are discussed in this paper, using contact angle measurements, electronic tensile testing machine, off-set printing test and FTIR. The static contact angle of water ranges from 129.7 to 90.7 o and tensile performance has improved significantly as the ratio of RF powers density change from 0.1 to 10. The ink density and depth of color during off-set printing are visually improved by using papers with hydrophobic surfaces coated composite films.

In this study, four types of Waste Paper Sludge Ash (WPSA) were explored for use as Supplementary Cementitious Materials (SCM) in binary system. The WPSA use varies in particle size range and surface area however similar in chemical composition. At first stage, Ordinary Portland Cement (OPC) was replaced by WPSA at 5% mass to mass basis as blended cement. Four size of WPSA was prepared which are unsieve, retained at 63μm, retained at 45μm and pan. WPSA blended cement (WPSABC) was introduced from the four size of WPSA that prepared earlier. Water to cement ratio selected was 0.50 and it keep constant at all type of blended cement. When compared with the control mix, result shows that hydration kinetics is affected by the particle size of WPSA. Pan WPSA has slightly higher peak of hydration kinetics and compressive strength of blended cement. At second stage, Pan WPSA was selected to undergo the further investigation on its performance. Pan WPSABC were prepared at replacement level of 5%, 10%, 15% and 20%, mass to mass basis. Same method and w/c ratio was used and compared with control mix. From the result, it is found that the peak for rate of heat evolution of Pan WPSABC occur earlier and slightly lower as compared to OPC. Pan WPSA also achieved it optimum strength at 5% replacement level which is more than control mix.

Compared with the lithography and traditional technology, ink-jet printing technology has huge advantages such as reducing costs, improving production efficiency and reducing environment damage. The silver nanoparticles conductive ink used as core material in ink-jet printing technology has been greatly developed. At present, the conductive inks for printed circuit usually has high sintering temperature, low adhesion, poor mechanical properties, high cost, which limit the further industrial application. In this paper, nano silver pulp was prepared through liquid phase reduction method, and a self-made protective agent ensured that the particle size distribution of silver particles is about 5nm. The above silver pulp was dispersed in the organic resin to get conductive ink with 20% (wt%) silver content. Under 170°Csintering, the electrical conductivity of the ink layer was 1.15×104S/m.

Moisture has a detrimental effect on oil-paper insulation life by lowering electrical breakdown strength. How does the space charge behavior of the oil-paper insulation system consisted by oil gap and oil immersed insulation pressboard with different moisture content? The space charge characteristics of the mixed insulation consisted of oil gap and pressboard with three moisture content were investigated using the PEA measurement system. The space charge accumulation behaviors at the interface between oil gap and pressboard were analyzed. The distortion of the electrical field in the oil gap and pressboard was also analyzed. Results show that there are many charges injected into the oil and the pressboard. The charges accumulated at the interface between oil gap and pressboard. The charges accumulated in the mixed insulation system become less with the moisture content increased. The difference of the electric field strength in the oil gap and pressboard become smaller with the moisture content increased.

A novel method of direct aniline multi-interfacial polymerization on paper substrate is introduced in this paper. Cellulose base papers with and without PAE reinforced were discussed. The PANI-paper composites after more than 3 polymerizations had much lower surface resistivity. Their mechanical strength and thermal stability were analyzed by tensile test and GTA. FTIR results explained that there was strong interaction between NH groups in aniline monomers and OH groups in fibers. Conductive composites made with PAE treated paper had both good thermal stability and good mechanical strength with high conductivity.

There are many researches about the effect of oil/paper proportion, testing temperature, AC/DC ratio and other effects on the breakdown characteristics of oil-paper insulation under the composite electric field. However, the breakdown characteristics of oil-paper insulation under the composite electric field in the process of ageing are rarely reported. In this paper, the breakdown characteristics of the oil impregnated insulation paper with different ageing condition under the composite electric field were investigated. Results show that there is no necessary link between the breakdown characteristics and the ageing degree of oil-paper insulation. The breakdown voltage value decreased with the rise of the AC component under the composite electric field. The breakdown voltage with aged paper changed by new paper is slightly higher than that of the aged oil being changed by new oil.

Copper-nickel alloys have been used in many applications in marine environments because of excellent corrosion and biofouling resistance. . This investigation is cover a review of many previous studies about the behavior of these alloys in marine environments with different environmental conditions including the effect of sulphur contamination, the effect of CO2, the effect of chlorine, the effect of flow velocity, the effect of temperature and the effect of adding some alloying elements to the alloy itself. There have been conflicting results in the past about the corrosion rate values and the chemical analysis of the corrosion films in different environmental conditions. More research is needed for studying the behavior of these alloys in marine environments to provide good assessment of the corrosion resisting characteristics.

First, the study chooses ten kinds of offset paper. By using a dynamic penetration analyzer (HVL-PDA) and water as test fluid, the dynamic absorption characteristics of the ten kinds of offset paper are measured. At the same time, proofs of offset printing patterns of these ten kinds of offset paper are made by using a printability tester. Then the depths of ink penetration in ten kinds of offset paper are measured by the Three-dimensional video microscopy system and the study analyzes the effect of paper dynamic absorption property on penetration depth of ink. The results of the analyses show that the penetration depth of ink is closely related to dynamic liquid absorption, thus the permeability of ink in offset paper can be predicted from the dynamic liquid absorption of offset paper.

The X-ray diffraction of hydrated calcium silicate is analyzed and is applied in papermaking. It shows that hydrated calcium silicate have certain crystalline state. The tensile strength, tearing strength and folding strength of paper decrease in different degree with the increase of dosage of hydrated calcium silicate while the whiteness and the printing color density of paper improve. T tensile strength and folding strength of paper decrease in varying degrees with the increase of dosage of PAM while the tearing strength of paper and the whiteness improve. And the printing color density of paper is the same.

As a non-destructive insulation diagnostic technique, the polarization spectrum method based on return voltage measurement has been employed to assess the state of insulation of the transformer. But how does the moisture content affect the parameters of RVM is not clear. In this paper, the effect of moisture content on the parameters of return voltage is studied based on experiments. The result shows that maximum value of return voltage (Urmax) and initial slope (Si) increase with the increase of moisture content in second-order function, while the central time constant (tcdom) decreases with the increase of moisture content in second-order function. The central time constant varies strongly with the change of moisture constant, so it is considered as a reliable indicator to evaluate the moisture level in oil-paper insulation system of transformer.

In order to know the coating effect and application of color ink-jet paper, the coating formula and printing quality of ink-jet paper were deeply studied. First of all, the coating liquid was prepared by dispersing and mixing the nanometer pigment, the adhesive and the other additives. Then the properties of ink-jet paper were tested and their surface profiles were characterized and evaluated with scanning electron microscope. Finally, the coating paper samples and the base papers were all printed with color ink-jet printer and measured with a spectrodensitometer. The study result showed that it can gain well coating and printing quality when the ratio of SiO2and TiO2is 3:1 and the content of PVA adhesive is 50%, especially paper whiteness is obviously higher than that before the coating.

In this paper, a vacuum freeze drying equipment was developed for vacuum deacidification of paper relics. The relation between freezing velocity and sample mass was studied experimentally, so did the relation between freezing velocity and pre-freezing time. The results indicated freezing velocity is inversely proportional to sample mass as well as the time used with refrigerating capacity equal to mass fraction of frozen water. Problems like melting or disintegration can be overcome by heating gradually. Radiation heating combined with conduction heating make sure the sample is heated evenly. Moreover, vacuum deacidification is available to remove acid of paper relics, and paper relics are kept intact by means of vacuum freeze-drying.

Humidity control paper board comprising natural polymer derivatives, porous natural minerals, inorganic salts, natural moisturizing material and paper was prepared by simple physical blending and its humidity control properties were tested. The moisture adsorption and desorption rate are 0.82 g/7h.g-1 and 0.71 g/7h.g-1, respectively. The adsorbed moisture amount is 0.85 g/g. It can maintain the relative humidity (RH) range between 50% and 60% within 20 min at 25 °C. Above all, the prepared paper board shows pronounced humidity control properties and the preparation technology is simple, which is feasible for production in large scale.

In order to improve the physical and color laser printing properties of paper, the polyvinyl alcohol and silica were used for pigmental surface sizing of paper. Under the previous conditions of solid content 12% and 14%, the effects of different ratio of PVA and silica such as 100:0, 15:1, 10:1, 5:1, and 1:1 on the physical properties of paper and laser printing performance were investigated. The brightness, opacity, roughness, color density, gray scale and image definition were measured after the surface sizing paper was calendared under the condition of temperature 70°C and pressure 4MPa. When the solid content was 12%, PVA: SiO2 was 1:1 and the solid content was 14%, PVA:SiO2 was 10:1, the brightness and opacity of paper obtained the maximum values. With the increase of silica proportion roughness increased at first and then decreased. Color density and tone reproducibility of paper was significantly improved by the pigmental sizing treatment as well as the dots and lines definition. The reasonable pigmental sizing scheme was as follow: solid content was 12%, PVA:SiO2 was 1:1, sizing temperature was 60°C, calendar temperature was 70°C and calendar pressure was 4MPa.

In order to prepare high-gloss water-soluble gravure varnish which is used on tipping paper, different content and types of filming resin with different content of all kinds of additives added are used to prepare water-soluble gravure varnish. Test its main performance and then use IGT apparatus to proof. The effect of varnish component and content on glossiness of water-soluble varnish is discussed by measuring glossiness of proof. The results show: different content and types of water-soluble filming resin have a great influence on the glossiness of water-soluble gravure varnish which is used on tipping paper; the glossiness of water-soluble varnish film can improve by adding auxiliaries such as cosolvent, substrate wetting agent, flow agent, wax emulsion and other promoter into water-soluble varnish system.

γ-Al2O3 namely activated alumina or alumina gel is widely used as a pigment on the inkjet paper at present. But it is easy to come out a particles agglomeration problem to restrict its application. In this paper, the γ-Al2O3 with coupling agents were modified to improve its dispersion in water. In the modification process, the he main modification parameters such as aluminum-zirconium complex oligomeric coupling agent TL-3A were selected to study. The parameters of addition, modification time and modification temperature were discussed. During the experiment, the best modification conditions were determined via orthogonal experiments. The polydispersity index PDI was used the target parameters to inspect via orthogonal experiments results and the affected factors. We found the best addition quantity of coupling agent, modification time and modification temperature to reach the minimum of the polydispersity index PDI introduction. The results showed that the best condition for carbonization alumina was: the best condition for export γ-Al2O3Subscript text 2.0%, modification time 30min, modification temperature 50°C。

paper formation, smoothness, bulk, ink absorption, printability. Abstract. The impact of the paper formation on smoothness, compressibility, uniform of ink absorption is discussed in this paper. The experimental esults indicate that the paper with bad formation leads to higher apparent bulk, and the paper with bad formation shows nonuniform calendering and low compressibility. The bad formation of paper also results in deformation and omission of printing dots, which affects directly the reproduction of the printing images.

In this paper we evaluated some surface characteristics of the Vacuum Aluminized Paper (VAP) to explore the ink adhesion on it. It is shown that this performance is quite unsatisfying due to the high gloss of the VAP which results in an even weaker surface energy than the surface tension of ink. The optimal drying time for the inked VAP under UV light with 125W of power is approximately 4.5 minutes, converts to the practical production, the printing speed of the VAP should be near to 7128 sheet/hour so as to fully solidify the UV ink thus acquires the optimal adhesion of ink.

The influence of temperature and relative humidity on the moisture content of paper honeycomb sandwich panels was studied. The moisture content of paper honeycomb sandwich panels was fitted by three mathematical models. The fitting results were evaluated by experimental data, and the best fitting model and its parameters were determined. The results indicate that in three models, the GAB (Guggenheim, Anderson and De Boer) model is the best suited to predict the moisture content of paper honeycomb sandwich panels in different temperature and humidity conditions.

The penetration and diffusion of ink droplet in paper coating have significant influence on the image quality in the inkjet imaging. The flight physical phenomenon of the ink droplet was researched and analyzed according to the hydrodynamic equations of multiphase flow discrete phase in this paper. Base on studying on the surface structure of paper coating, the mechanism of impact, penetration and diffusion between ink droplet and paper coating also was researched in this paper from the perspective of energy conversion in the imaging process. The proposed mathematical model consisted of the factors of hydrodynamic characteristics for ink droplet and the physical characteristics of paper coating, we could get the maximum diameter of ink droplet spreading in paper coating through solving the model and obtain viscous loss and energy consumption in penetration of ink droplet by experiment, and then calculated the average penetration depth of ink droplet.

Cationic polyacrylate emulsion was used as surface sizing agent and the effects of emulsion properties on paper mechanical properties were studied. The mechanical properties of sized paper gradually increased with the increase of solid content, viscosity and positive charge density of emulsion and decreased with the increase of particle size of emulsion. Tensile strength, folding endurance and tearing strength on machine direction were increased 33.62%, 11.99%, 6.79% respectively when the paper with single emulsion layer was used oven drying methods.

Two equivalent models based on sandwich panel theory and equivalent panel theory were discussed in this paper. By analyzing the performance of fiber - paper honeycomb sandwich structure compound panel by bending load, the computational results are in accordance with test and Engineering software ANSYS. Therefore, it shows that the finite element equivalent models are reasonable and practical for the optimization design of fiber - paper honeycomb sandwich composites.