Search

The detailed description about the OMIS (One Machine-Infinite Bus) and the SLIS(Single Load -Infinite Bus)will be done in this paper and the detailed introduction of these two concepts(the coherent generators and the coherent buses) and their aggregation. Based on the new OMIS model, the new methods of identifying the coherent generators and aggregating the coherent generators will be advanced. Based on the coherent generators, the new algorithm for the reserving coefficient of the steady angular stability will comes into being. Based on the new SLIS model, the new methods of identifying the coherent buses and aggregating the coherent buses will be put forward. Based on the coherent buses, the new algorithm for the reserving coefficient of the steady voltage stability will be brought about. A real example is used to validate the idea in this paper. A discussion on the angular references between the online data and the offline data will be done when the phases from the WAMS are used. The steady stability of two generators model will be acquired.

In this paper, the stability of local transductive regression algorithms is studied by adopting a strategy which adjusts the sample set by removing one or two elements from it. A sufficient condition for uniform stability is given. The result of our work shows that if a local transductive regression algorithm uses square loss, and if for any x, a kernel function K(x, x) has a limited upper bound, then the local transductive regression algorithm which minimizes the standard form will have good uniform stability.

This paper reports the synthesis of ZnS Quantum Dots (QDs) embedded in PVA by aqueous precipitation method and its application in antibacterial as well as to find or estimation of Escherichia coli (E.coli) concentration by using ZnS/PVA QD based mem-mode nanodevices. The as-synthesized ZnS/PVA samples are characterized by UV-Vis spectroscopy (UV), Photo luminescence (PL), X-ray diffraction (XRD), Transmission Electron Microscopy (TEM) and Scanning Electron Microscopy (SEM). Antibacterial property of ZnS/PVA QDs against gram positive (S.aureus) as well as gram negative (E.coli) are tested. The antibacterial property is found to be more in S.aureus in comparision to E.coli. Mem-behaviour of the as-fabricated devices is observed through electrical characterization. COMSOL MP Software is used for simulating I-V characteristics. The voltage gap is found to be a promising parameter for estimating E.coli concentration with ZnS/PVA QDs as active material and an electrical circuit is presented

The characteristic pinched hysteresis behavior of memristors has been reported by stacks of a variety of materials. This paper aims to examine the principles of logic design using such two terminal memristive systems for high performance digital circuit applications. As against logic design with standard CMOS, the benefits of logic design with memristors have been stated. The realization and operation of memristor based AND and OR hybrid logic gates obtained by integrating memristors with standard CMOS logic have been discussed. The IMPLY and MAGIC logic families have been demonstrated by covering MAGIC NOR and NAND logic gate implementation with MAGIC NOR in detail. A qualitative comparison has been drawn towards the end of the paper to conclude on the suitability and application space for each of the logic families studied in this paper. This work also describes the hybrid CMOS-memristive logic family known as MRL (Memristor Ratioed Logic). With the addition of CMOS inverters, this logic family's OR and AND logic gates, which are based on memristive components, are given a full logic structure and signal restoration. The MRL family, in contrast to earlier memristor-based logic families, is compatible with conventional CMOS logic.

Monodispersed Ag nanorods were synthesized using a one-pot synthesis method. These Ag nanorods normally manifest dual surface plasmon resonance (SPR) peaks. This work presents a study of the variation of SPR peaks with variation in the shape of Ag nanorods. Shape variation was achieved through the degradation of a shape-controlling agent (PVP in this work) under white light irradiance with silica passivation to halt further shape variations. This paper also reports the growth & characterization of thin films of the synthesized rod-shaped silver nanoparticles on glass slides along with studies on band pass filter characteristics of the as-synthesized nanoparticles.

Road markings regulate and direct traffic by conveying specific information. It is of great significance to develop new road marking materials and improve the visibility of marking materials for improving traffic efficiency and ensuring traffic safety. This paper summarized the development status of various reflective road markings at home and abroad. In addition, the energy storage luminescent fluorescent/phosphor marking lines in road marking was emphatically generalized to evaluate the advantages and disadvantages of different improvement methods. Overall, strontium aluminate doped with Eu2+ co-doped with Dy3+ (SrAl2O4:Eu2+, Dy3+) phosphors and self-luminous pavement for energy storage had great prospects in improving road safety and reducing energy consumption.

Spinel ferrite nanoparticles are potential candidates for multiple biomedical applications. Spinel ferrite nanoparticles have been studied extensively for understanding physical, chemical, electro-optical as well as magnetic properties which are fascinating due to cationic distributions corresponding to tetrahedral sites and octahedral sites in a cubic phase. Biocompatibility and large magnetic moment are basic requirements in spinel ferrite nanoparticles for efficient functioning in specific application purpose. Fe3O4 (magnetite) is an important member of spinel ferrite group with high chemical stability and ferrimagetic material property at nanodimension. Superparamagnetic state and biocompatibility of magnetite (Fe3O4) spinel ferrite nanoparticle has already been proven. Spinel ferrite magnetite nanoparticles have been developed based on precipitation of iron oxide using ferric and ferrous ions at the ratio 2:1 in alkaline media at and above 100°C. The experimental parameters have been set to synthesize pure and uniformly sized magnetite nanoparticles. No other phases of iron oxides were detected other than magnetite spinel phase in the XRD result. The average crystal size has been determined from XRD peak broadening. Absorption spectra were investigated using UV-Vis Spectrometer and FTIR. Thermal and magnetic measurements were carried out Digital Scanning Calorimeter and SQUID Magnetometer. One sample of the prepared nanoparticles with polymer coating of polyvinyl alcohol has been studied for superparamagnetic nature. Superparamagnetic particles show saturation value of magnetization 51.26 emu/g at 100 K. ZFC-FC curves for two samples with polymer coating of polyvinyl alcohol and hydroxy-propyl methyl cellulose have also been studied. Keywords: Spinel Ferrite, Magnetite, Ferrimagnetism, Transition metal oxide, Superparamagnetism. Statements and declarations Competing Interests: The authors declare that there is no competing financial interest that are related directly or indirectly to the reported work in this paper. Conflict of interest: There is no conflict of interest. Acknowledgements The Authors are grateful to IISER Bhopal, CRF facility for providing instrumentation facility to characterize magnetic properties. We acknowledge thanks to Lovely Professional University for providing us necessary characterization technique for the XRD analysis and thermal analysis.

The recent developments in dielectric elastomers (DE) are spectacular. Currently, a DE as an actuator, 0.15 g of acrylic sandwiching SWCNT electrodes, is capable of lifting a weight of 8 kg by more than 1 mm at a speed of 88 msec. In the near future, DE motors could be used to drive electric vehicles. Moreover, the DE can be used as a high-efficiency sensor with the same structure. With a diameter of 20 mm and a thickness of 0.5 mm, it can accurately measure pressure from several kg to 150 kg. In addition, reversing this DE actuator (DEA) movement also enables high-efficiency power generation. In other words, when the DEA is stretched or pushed, it generates electric power. Single wall nanotubes (SWCNTs) were used as an electrode, and an acrylic DE power generation cartridge with a diameter of 80 mm was used. When the center of the DE power generation cartridge is pushed by about 15 mm, a power of 33.6 mJ is generated. Using these two DE cartridges, it was possible to charge a secondary battery through a DC converter. In addition to this power generator, practical research and development of power generation using wave power, wind power, waste heat, and fluids (ocean currents, water currents, etc.) is progressing. In this paper, we have described state-of-the-art DEAs, DE generators (including the case that the power generated locally by microgenerators are consumed locally), and DE sensors and explained their usefulness.

In this paper, a hollow square cross-section carbon fiber/epoxy composite beam was designed and manufactured. Evaluation of the beam behavior considered orientation and stacking sequence, aiming to reduce the number of layers and weight. Finite element method (FEM) was used to simulate the performance of the composite beam under 3-point bending and using three failure criteria, Tsai-Hill, Tsai-Wu and maximum stress. In order to identify the input parameters for the model, flat composites were tested under tension and compression. It was concluded that a minimum of 12 layers of unidirectional carbon fiber were required to reach the required load (44.5 kN). The prototype was successfully fabricated by vacuum-infusion process and subjected to 3-point bending test. The experimental failure load was within the predicted range by the Tsai-Hill failure criteria and maximum stress.

Along with the development of the science, the communication technology has already developed from the traditional air to the outer space and submarine. So, the UAC is getting more and more attentions from the researchers for its business and military value. However the local hydrology environment and the weather must be considered when the actual UAC experiments are carried and the experimental cost is so expensive that it is hard to carry on enough experiments[1]. What’s more, There isn’t a software that can compare all these algorithms conveniently, although there are many algorithms nowadays for UAC[2]. This paper studies to construct a software which can combine many algorithms and compare them in one unified frame. Also the software can help us design actual experiment system to obtain more valuable data in limited time.

The sulfur content present in graphene oxide prepared by Hummers' method has only been addressed by few papers so far. By modified Hammers method we synthesized thermally stable in ambient environment multilayer sulphur-doped graphene oxide. The samples were heat treated in an electrical furnace setup at different ambient temperatures and their crystallite size and linear coefficient of thermal expansion were extracted from Raman band intensity peak ratio as a function of temperature. We found unusually large (in comparison with graphene oxide) contraction on heating of multilayer two weight percent sulphur-doped graphene oxide with carbon to oxygen ratio of 2.3 in a narrow temperature range (308-318 K) with the lowest value of the linear thermal expansion coefficient of -18 ppm 1/K. Based upon an examination of the synthesized sulphur-doped graphene diffractograms, it is suggested that negative thermal expansion stems from the phonon backscattering by the sulphur impurity sites and the edges of the layers. The obtained experimental results have potential practical applications for fabrication of solar cells, sensors, lubricators, thermal actuators and also wavelike (second sound) thermal transport structures.

The cutting fluid plays a significant role in minimizing heat generation and chip removal process during the machining of materials, hence improving tool life and surface finish of the workpiece. Many researchers have focused on minimum quantity lubrication (MQL) among the existing methods on the application of the coolant as it reduces the usage of coolant by spurting a mixture of compressed air and cutting fluid in an improved way instead of flood cooling. The MQL method has demonstrated to be appropriate as it fulfills the necessities of ‘green’ machining. Additionally, considering current environmental issues and provisions for safe healthy working conditions at the workplace, it is important to divert machining processes towards an eco-friendly path. Hence, the focus of research has been shifted to MQL using eco-friendly lubricants for green and sustainable manufacturing processes. In this review paper, the effect of different vegetable oil-based biodegradable coolants like castor oil, coconut oil, palm oil, etc. for different machining process parameters like cutting force, cutting temperature, surface finish, tool wear, etc. has been reviewed. It is observed that proper selection of cutting parameters along with lubricant through MQL can provide enhanced machinability to get desired outputs.

Forging tools must be able to withstand very strong mechanical, thermal, tribological, and chemical stresses. The extent to which a tool can withstand these stresses depends on the material used and its pre-treatment as well as the heat and surface treatment, i.e. the load capacity. The ratio of stress to load capacity determines how high the tool life of a forging tool is. This paper deals with the variations in the tool life of forging tools using the example of a specific industrial stage sequence and production conditions. Due to a large number of influencing variables that have an effect on the tool during the entire tool life history, the focus of this work is placed on influencing variables of the forming process. Based on real production parameters of a forging company, which are recorded during a period for the investigation, the process data are analyzed about an influence on the tool life. The investigation focuses on four influencing variables, namely the subjective assessment of the end of the tool life, the interaction between the forming stages, production interruptions, and the cooling and lubrication of the forming tools. For the parameters that are not yet recorded during the trials, promising available measurement methods are identified and tested under laboratory conditions. One example of this is the recording of the actual spray quantities that are sprayed onto the tool surface before the forming process. The results of the investigations show that the tool life fluctuations can be reduced by about 16% and as a consequence, the average tool life can be increased by about 13%.

Many issues such as low accuracy rate, poor filtration efficiency, and too much network resource occupancy exist in most information filtering systems in the current market. Therefore, there is a great demand to develop a new network filtering system. In this paper, agent techniques are first reviewed, and then the architecture and the working mechanism of a multiagent-based information filtering system is presented. Finally, the design method for core components of the system is given.

The ultraviolet (UV) fluorescent anti-counterfeiting offset printing ink, which can emit visible light (400-800 nm) under the excitation of ultraviolet light (200-400 nm), has been extensively adopted in the modern printing technology. In this paper, we used the red-emitting phosphor BaCaBO3F: Eu3+, Li+ as the fluorescent pigment for printing ink and investigated the influence on additive amount of the luminescence properties of fluorescent ink in order to determine a more ideal ratio of fluorescent ink .Besides, the shear viscosity, thixotropy, visco-elasticity and the temperature dependence of viscosity according to the rheology theory and rheological technique were also studied, and finally the valuable parameters and patterns were successfully obtained.

In this paper, the abnormal phenomenon of fixed series compensation GAP is discussed. The main reason, too large attenuation of the fiber communication between the GAP trigger equipment and control protection screen input plate is analyzed. The improved measurement to the fixed series compensation system operation and design is proposed.

This paper is based on the BP neural network, the identification method of character and the specific implementation steps were designed. Moreover, the method through the test form has been proved. The accuracy of character recognition is higher.

In this paper, polypropylene (PP) melt blown non-woven fabric is treated by atmospheric He, He/O2 or He/CO2 glow discharge plasma. The variation of the surface hidrophilicity of PP sample is experimentally investigated by the surface water contact angle. The results show that the surface water contact angle firstly has a sharp decline and then up to saturation. It is worth noting that the time the water contact angle is up to saturation greatly shortens when a spot of O2 or CO2 are added into the atmospheric He. In addition, when the PP samples are treated by the atmospheric glow discharge plasma, it is necessary of selecting a right applied voltage.

Since the pig iron cost is the major cost of steel, reducing the pig iron cost is the key of reducing the cost and enhancing the competitive capacity of iron and steel enterprise. The law of the cost of pig iron change with time was analysed in the paper. The major factors which affect the cost of pig iron are confirm by the analysis the composition of the cost of pig iron, then the measures such as reducing material fee, injecting pulverized coal economically, improving BF operation and strengthening management are advised.

More and more environmental hormones (EHs) had been released into the environment, and it has caused a certain influence and interference on normal activities of the organisms. The EHs genetic toxicity testing methods have been constantly improved with the development of molecular biology techniques. This paper mainly reported the gene-toxicity methods, present status and took an outlook for the research trend on EHs.

This paper presents the results of an experimental investigation into the Ultimate Elastic Wall Stress (UEWS) of ±55° filament wound composite pipes. The UEWS test appears to provide an attractive alternative to the current method, and has proved to be one of the most effective in term of accuracy and speed. Moreover, it has been found to be sensitive to changes in key manufacturing and raw material parameters. The pipes were subjected to biaxial loading, which was achieved by combinations of hoop and axial stress. Loads were applied as groups of cycles which, were gradually increased until the UEWS had been determined. Various ratios of hoop to axial stress were applied to the pipes, ranging from pure axial to pure hoop loading at room temperature and at 65°C. These ratios were investigated by applying different pressures in both the main and small chambers built inside the pipe, and therefore it was unnecessary to add any external loads to the pipe wall. Tests were also conducted to observe leakage through the pipe wall. The main failure mode observed was weepage through the pipe wall, which was due to intensive matrix microcracking. The results from the UEWS tests are presented in the form of failure envelopes showing the effects of testing at an elevated temperature. Finally, degradation in the elastic properties of the pipe wall is also discussed and plotted against wall stress.

This paper was combined with the third Huaian pumping station to study the dynamic characteristics of the bulb tubular pumping station. By using dynamic finite element analysis method to create Huaian pumping station modes. Then using ANSYS Model Analysis and harmonic response analysis, the vibration modes and dynamic response were researched deeply. According to the mode analysis results, the fundamental frequencies of upper pump house were determined for 1.36Hz and the fundamental frequencies of substructure were determined for 20.11Hz. The dynamic response of the bulb tubular pumping station structure under fluctuating pressures is calculated by ANSYS harmonic response analysis, and the results show that dynamic displacement satisfied the maximum allowable of architectural construction permission，so it can satisfy design requirement, which provides references value for other tubular pumping station in anti-vibration design.

Plastic waste disposal is among the most challenging problems of the current era. Therefore, new methods and applications for the utilization of waste plastics are increasingly needed. To find them, it is essential to research and develop the material properties of recycled plastics. The effect of different ultraviolet light (UV) stabilizers on the color stability, melt properties and tensile properties of mixed waste plastics blends was studied in this paper. The mixed waste plastics collected from two different waste sources were prepared as specimens by injection molding, and studied with two different types and loading amounts of UV stabilizers. UV absorbers (UVAs) and hindered amine light stabilizers (HALS) were used as UV stabilizers. A specimen produced without the addition of a UV stabilizer was used as a reference specimen of both the blends. After the accelerated weathering, the addition of a UVA provided an improved, smaller change in color than the addition of HALS. Among the tensile properties, the addition of UV stabilizers clearly improved the tensile strength and tensile modulus for almost all the studied specimens. Additionally, the melt properties of both the studied plastic blends were found to be increased by the addition of UV stabilizers. Post-print / Final draft

With the continuous development of online shopping, a day will generate tens of thousands of consumer records. E-commerce sites want to recommend the consumers that they may be interested in the products by analyzing the consumer historical consumption data. However massive consumer records led to recommendation speed getting slow by using the traditional personalized recommendation algorithm. By researching on the collaborative filtering algorithm based on ALS and the MapReduce parallel programming model, we explore parallelization of collaborative filtering algorithm based on ALS. The experimental results show that the algorithm in this paper can improve the computing efficiency.

The aim of this study is to investigate the contaminant removal efficiency in wastewater when disposed by carbon fiber ecological grass. The paper analyzed the TN, TP, CODMn, NH4+-N and SS removal efficiency when used different dosage of carbon fiber ecological grass. The research results indicated that the contaminant removal efficiency at pH=8 is higher than pH=6, 7 and 9. When DO between 5.6 and 8, the TN, TP and NH4+-N removal efficiency has a highest level, the removal efficiency is 83.91%, 68.16% and 83.3% respectively. When DO between 8.1 and 10.7, the CODMn removal efficiency has a highest level, the removal efficiency is 57.93%. The stirring rate is important to the contaminant adsorption and removal. Consequently, selecting carbon fiber ecological grass in wastewater treatment is a good choice.

In this paper, Button rock asphalt particle was directly added into hot asphalt mixture (HMA) to produced high modulus asphalt mixture (HMAM). In order to evaluate the performance properties of HMAM with BRA, dynamic compressive complex modulus (E*) test, rutting test and moisture resistance test were used to investigate HMAM with BRA and HMA with SBS modifier. Test results indicate BRA can greatly improve dynamic E*and rutting resistance of HMA compared with SBS modified asphalt mixture. Moisture resistance ability of HMAM with BRA has the same level with SBS modified asphalt mixture. Therefore, BRA particle can be used to produce HMAM, which have more superior performance properties than SBS asphalt modifier.

In this paper, aiming at the heat resistance and thermal deformation process of titanium matrix composites 0 vol.%, 2.5.vol.%, 5.vol.%. Thermal simulation experiment of titanium matrix composites with different (TiB+TiC) strengthening phase content. The measurement accuracy of material displacement is 0.01 mm. The compression is 70%, and the strain rate is 0.1 mm/s and 0.01 mm/s respectively. Compression tests at different strain rates and temperatures were carried out. The experimental results show that when the (TiB+TiC) 5vol% titanium composite is deformed at 0.01mm/s low strain rate, the peak stresses corresponding to 25°C, 250°C,350 °C and 500°C are increased to 1096MPa, 835MPa, 646MPa and 416MPa respectively. Under the condition of high strain rate of 0.1mm/s, the peak stresses corresponding to 25 °C, 250 °C, 350 °C and 500 °C are increased to 1230 MPa, 896 MPa, 723 MPa and 471 MPa respectively. The deformation law of stress rheological curve is roughly the same, and the high temperature zone has good plastic deformation ability. The titanium matrix composite has high compression rheological mechanical properties and good high-temperature plastic deformation ability. It is the preferred material component for the preparation of titanium matrix composite and powder forging.

This paper mainly studies the composition of strengthening phase, characteristic precipitation temperature and composition range of strengthening phase in Ti-Al-Mo-Zr-Si medical titanium alloy, and the influence of element changes on the content and microstructure of strengthening phase. Promote the formulation of thermodynamic process of titanium alloy powder metallurgy, as well as the formulation of alloy hot working and solid solution aging process. In this paper, Panda thermodynamic software is used to calculate the multicomponent alloy thermodynamics and multicomponent phase diagram of titanium alloy materials. The effects of Al, Mo, Zr, Si and other elements on the precipitation of strengthening phase and the phase transformation content of solidification structure were obtained. It is found that the content of Mo is more than 2 wt.% β phase transition precipitation angle. Meanwhile, in order to avoid the excess of precipitates such as Mo5Si3 and M3Si, the content of Mo should be less than 4.6 wt.%. The content of Zr can be maintained at about 1.5 wt.%. If the aging precipitation of the material is considered, it can be controlled to be less than 2 wt.%. The content of this paper is the basis and improvement of titanium powder metallurgy technology and rapid prototyping technology.

In this study the dynamic Smagorinsky model (DSM model) and an algebraic model for the subgrid turbulent kinetic energy have been implemented into KIVA3VLES code to investigate the atomization and evaporation processes of diesel spray in a constant volume vessel. Based on the experimental results of the liquid and vapor phase distributions as well as the results obtained by the differential subgrid scale kinetic energy (K-equation) model, the paper reveals the influence of the turbulent kinetic energy model on the fuel spray prediction. Computational results show that by combining the DSM model and the algebraic subgrid turbulent energy model, the turbulent diffusion of droplets can be reasonably simulated, the liquid penetration and the predicted liquid and fuel vapor mass fraction contours are close to the experiment results. At the same time, the turbulent kinetic energy given by the DSM model is in agreement with the results by the K-equation model, but with less computational cost..

Cylinder with multiple diagonal slits is one of the core parts of longitudinal-torsional resonance ultrasonic device. Its structure was more complex, the traditional processing processed it very difficult, and the traditional analytical methods were also difficult to make accurate description to system. The paper researched cylinder with multiple diagonal slits using experimental method, analysis of electrical discharge machining forming tools of the slits and three-dimensional modeling; developed cylinder with multiple diagonal slits, analyzed longitudinal-torsional resonance and mechanical properties of cylinder with multiple diagonal slits using finite element analysis method. Tested resonant frequency of cylinder with multiple diagonal slits with precision impedance analyzer. The finite element analysis results compared with tested results, and analysis of error between them, finite element analysis results slightly lower than the test results but the error was within the allowed range. Comparison of results and analysis of error indicated that developed cylinder with multiple diagonal slits meet requirement.

Fiber grating sensor network plays an important role in evaluating the bridge health condition and gaining bridge structure characteristic.Bridge structural distortion and variation of stress is associated with temperature.So it is essential to make temperature prediction bases on the length of wave which gained from fiber grating sensor network system.Traditionally, we apply least square method to predict temperature.In this paper,we use method of relevance vector machine (RVM) to make it.

The development of materials with high damping and energy absorption properties in the form of bulk materials or coatings is today a target for designing components and structures with improved durability and survivability to serve in fields such as aeronautical, mechanical, civil and environmental engineering. This paper presents the results of the dynamic mechanical characterization conducted on reinforced polyurea composites. The mechanical properties of two types of composite materials utilizing the polyurea elastomer as a matrix are compared with those of the pure polymer. The composite materials show a substantial increase of the damping ability. Such materials can be produced in the form of coatings and successfully applied for maximizing the damping of mechanical and structural vibrations or for limiting the damage effects of impact events on structures and components.

This paper investigates the thermal performances and heat gain reduction of a new roof tile design referred as Ventilated Roof Tile (VRT) compared with an ordinary corrugated concrete roof tiles (CCR). The outside dimension of each small house was 1.70 x 1.70 x 2.85 m3 (W x L x H) and inside dimension was 1.50 x 1.50 x 2.20 m3. The volume of each room was 4.95 m3. The gable roofs slope were 25o and surface area of VRT was 2.58 m2 per each side facing north and south. The VRT tile composed of upper cement plate 40 × 40 cm2 and lower cement plate 30 x 40 cm2. Between plates was 3 cm thickness air gap. The experimental results showed that the top surface of VRT was lower than CCR about 2.10°C for average temperature (from 6:00 18:00) and made VRT room temperature lower than CCR about 1.41°C for average temperature. VRT could reduce heat gain with air flow rate through the roof tiles gaps varied following the solar radiation, during time 8:00-17:00 the natural ventilation varied from 0.003-0.014 m3/s (10.6-50.0 m3/hr.). Observed that, during 17:00-18:00, the air flow rate is about 0.003 m3/s (10.8 m3/hr.) due to heat accumulated in the attic space and roof tiles.

Among other parts made of brass there are also the blades and the rotors of the hydraulic machines, respectively ship propellers, which during operation are degraded by cavitation erosion. As a result, most of the researches, including the most recent ones, are focused on the morphological analysis of structures eroded under the impact of micro-jets and shock waves, produced by cavitation hydrodynamics. The goal is to create new materials, but also to use new treatment technologies to increase cavitation resistance. As the literature is quite poor in studies related to the materials resistance to cavitation erosion, respectively treatments and technological procedures of it’s improvement, this paper presents the research results on the behavior of vibration cavitation erosion, carried out on three sets of CuZn39Pb3 brass samples, subjected to volumetric heat treatments of hardening for putting in solution at 800°C, followed by tempering at 250°C, 400°C and 600°C. The characterization of the behavior and the cavitation resistance of the structures resulting from the applied heat treatments is performed based on macroscopic images, taken at different representative periods, SEM images at the end of the test duration and values ​​of specific parameters recommended by ASTM G32-2016. The analysis highlights the differences caused by the change in structure by varying the temperature, but also the hardness of the surface exposed to the cavity. Thus, of the three treatments, it is found that the best resistance to cavitation is conferred by the structure resulting from hardening at 800°C, with tempering at 250°C.

The present paper analyzes the differences in behavior and resistance to erosion through vibrating cavitation, between the bronze structures CuSn-12C resulting from two volumetric thermal treatments of hardening and tempering. The analysis was performed on the basis of macro and microscopic images, as well as on the basis of the histogram in which the values ​​of the reference parameters used in the laboratory custom and prescribed by the international norms ASTM G32-2016 are compared. This shows the dependence of the degree of erosion as a function of the temperature of tempering heat treatment, after hardening, as a result of microstructural changes and the hardness of the surface attacked by cavitation. The experimental research is performed on the standard vibrating device within the Cavitation Erosion Research Laboratory of the Politehnica University of Timișoara.

Welding tools are a determining factor in obtaining welded joints with desired characteristics. The international community pays great attention to research aimed at establishing the optimal characteristics of friction stir welding (FSW) tools. With the development of the FSW welding process with its own contributions, ISIM Timisoara has developed complex research resulting in the conception and design of (innovative) FSW welding tool solutions. A very important factor especially when welding high hardness materials is the durability / lifespan of FSW welding tools. The paper presents general considerations regarding the qualities that FSW welding tools must meet in general, but also ISIM achievements in the field of design and operation of welding tools. Studies regarding operating behavior of welding tools made of sintered tungsten carbide P20S, in terms of service life (wear), both in the case of applying the classical FSW welding process and the method of friction stir welding in inert gas environment (FSW-IG), when joining steels with wide industrial use (304L stainless steel, respectively DD13 steel), are also presented. Concrete data is presented with values of the degree of wear of the tools in the unit of time, in their critical areas: tools made of X38CrMoV5 steel alloy used for welding aluminum alloys with different characteristics, respectively tools made of sintered tungsten carbide P20S used for welding S 235 JR + N steel and 304L stainless steels.

Due to its characteristics, DD13 steel is recommended for various applications in the automotive field (including in the manufacture of components for car bodies). The paper presents solutions proposed by ISIM Timisoara for welding of DD13 steel, as alternative solutions to conventional welding processes. One solution that has proven to be viable for joining DD13 steel is the friction stir welding process (FSW). In terms of the quality of the welded joints obtained by applying the classic FSW welding process, these welds were excellent. In an attempt to obtain other benefits, mainly related to the efficiency of the welding process, ISIM Timisoara has developed research programs for the study and application of other methods based on the FSW process principle, namely: - hybrid friction stir welding ultrasonic assisted FSW-US; - friction stir welding in inert gas environment FSW – IG. The important effects due to the application of these methods are: improving (as appropriate) the degree of plasticization of the materials to be joined and increasing the degree of mixing of the materials as result of ultrasonic assistance of the FSW welding process; improvement of the welding process by reducing the pressing forces of the tool during welding, with an effect on increasing the service life of welding tool; respectively improving the aspect of the weld and some mechanical characteristics of the welded joints (at tensile tests, respectively static bending test). The obtained results showed that the two methods derived from the classical FSW welding process, can be used in industrial applications, with important benefits.

This paper covers the literature review of the work by author, who have been involved in the subject of machine element repairing from the techno-economical point of view. Positive aspects of repairing, as opposed to purchasing new parts are shown and discussed. All of the examples given as part of the literature review are related to real, practical problems. It was concluded in all cases, that the repairing of damaged parts was the better option, since not only did it cost significantly less, it also noticeably decreased the equipment downtime, as there was no need to wait for the new part to be delivered.

Sustainable development requires green energy and low carbon footprint in manufacturing sector of photovoltaic systems. The electrical connections of photovoltaic cells need to have low electrical resistance in order to reduce the electrical losses and therefore to improve the performance of the photovoltaic panels. This paper aims to present researches related to bonding of wires that connect solar cells by using microwave technology. The microwave bonding has the main advantage that offers fast bonding but, in the same time, this technology does not offer stability of the thermal heating. Two different unwanted phenomena like thermal runaway and plasma arc discharge often lead to the damaging of copper and aluminum wires used in electrical connection. The study presented in this paper is focused on simulation of the thermal field developed in copper wires in order to optimize the bonding process and increase the quality of products. The simulation of the thermal field has been done using Fourier equations for conducting heating in copper materials and eutectic alloys. The simulation model has been validated through experimental heating using a 6 kW water-cooled microwave generator controlled by a matching load auto-tuner for best transfer of the power from generator to copper wires. The temperature has been measured in real time using an infrared pyrometer for metals with 2.3 μm spectral range and measurement range between 0o C and 7000 C. The study is finalized with elaboration of mathematical model for microwave-injected power as function for temperature developed in copper wires that can be applied with success in further microwave bonding applications of copper wires. In addition, the electrical resistance of bonded wires was measured in order to collect feedback for improving the microwave bonding process.

The manufacture of photovoltaic panels for the production of sustainable energy also involves the stage of electrical connection of the cells in the panel structure. This electrical connection is made by soldering of copper strips on the negative electrode of the cell. During the bonding process, due to the temperature of approximately 220-240°C at which the connecting strip is continuously heated, cracking processes of the upper layer of glass from the cell surface were identified. For this reason, it is necessary either to heat to lower temperatures, a solution that is not viable due to the melting temperature of the solder alloy which usually exceeds 210°C, or a different dosing of the heat flux. The solution proposed in the paper is to create a variable heat flux that allows the melting of the solder alloy, but at the same time to reduce the thermal load of the glass support layer. Through the proposed variant, the energy dosing is done with the help of a heating system consisting of two sources, an ultra-acoustic energy source and a classical resistive source. The resistive source provides an amount of energy to ensure a temperature in the range of 60-140°C, the difference to the melting point of the solder alloy being transferred locally by ultrasonic pulses. Research has highlighted the need to limit the range of values of the pressure of the circular sonotrode, which positively influences the mechanical stress of the photovoltaic cell, but also leads to a reduction in the joining speed. The dosing of the two components of the total energy, the one coming from the resistive source and the one coming from the ultra-acoustic vibration source is decisive for the efficiency of the joining process and for the quality of the soldered joint. Microscopic analyses revealed micro-cracks of the glass surface layer at forces higher than 100 N. Areas with lack of soldering for resistive heating at temperatures lower than 130oC were highlighted, the difference of 90-110°C being achieved by the contribution of ultra-acoustic energy.

The blade, made of TC11 titanium alloy, is prone to result in fatigue failure in the formidable environment in aero-engine. So a higher performance request of the material is brought forward. In this paper, laser shock peening(LSP) as a solution is applied to TC11 titanium alloy and microstructure, residual stress and microhardness with and without LSP were examined and compared via transmission electron microscope(TEM), X ray diffraction(XRD)and microhardness tester. The TEM results indicate that a great high density of dislocations are generated and evolve into the dislocation wall, sub-boundary and grain boundary. The nanocrystallites are formed and become smaller and more uniform with greater impacts. A high compressive residual stress above -540MPa is introduced with an increasing plastically affected layer with different impacts. The microhardness test result shows that LSP can obviously increase the hardness by 20 percent or so, and the affected depth increases with the impact from 600μm to 1200μm.

This paper conducts the fault tree analysis on Ship Dangerous Chemicals Leakage emergency of Three Gorges Lock with the method of safety system engineering, draws a map of fault tree analysis, representing intuitively the basic events which can bring about top events as well as the logic relationships between them, obtains the minimum cut set, minimum path set and structure importance through qualitative analysis of FTA, and points out the possible ways to prevent the occurrence of accidents.

The synthesis and characterization of spin-coated Al-doped ZnO (AZO) thin films with varying Al concentrations (0%, 5%, 10%, 15% and 20%) onto glass substrates have been demonstrated in this paper. The structural, electrical and optical properties of the spin-coated thin films have been investigated by Scanning Electron Microscopy (SEM), Energy Dispersive X-Ray (EDX) analysis, Van Der Pauw method and UV-visible spectroscopy. The EDX study shows well-defined peaks which confirm the presence of only Zn, O and Al and no other impurities in the films. The increase of Al and decrease of Zn weight percentages with increasing doping level confirms the effective substitution of Zn by Al. SEM of the surfaces of the films shows that undoped ZnO films contain particle agglomeration which is reduced with Al doping and the surfaces of the films gradually became more uniform. The thickness of the AZO films varied from 86 to 699 nm with increasing Al doping concentration. The electrical conductivity of the films increased up to ~ 7 × 10-2 (Ω.cm)-1 due to doping with 5% Al concentration. The optical transmittance highly increased above 95% in the visible range with the introduction of Al dopant and it kept rising with the increase of Al concentration. The optical energy band gap of undoped ZnO increased from 3.275eV to 3.342 eV with 5% Al doping.

With the development of new energy vehicles, it is necessary to develope new fast charging cathode materials for lithium ion batteries. This paper reports a simple carbon thermal reduction routine to synthesize layered LiMoO2 cathode for Li-ion batteries. Impurity-free micro-crystalline powders were synthesized by one-step method with a thermal treatment at 800°C for 5 hrs under N2 atmosphere. The structural, morphological and electrochemical properties of LiMoO2 were characterized by using X-ray diffraction pattern (XRD), scanning electronic microscopy (SEM), charge/discharge cycling and electrochemical impedance spectroscopy (EIS). The diffraction results indicate that the prepared sample has a layered hexagonal structure related to α-NaFeO2. The secondary particles are in order of 2.0 μm length on average with homogeneous distribution. The initial discharge capacity of LiMoO2 is 110.9 mAh·g-1 at 0.1 C, and the capacity can still remain 92.8 mAh·g-1 after 100 cycles. The good cycling performance and high rate discharge performance are attributed to the smaller charge-transfer resistance revealed by EIS results.

The strong vacuum ultraviolet (VUV) radiation absorption and energy transfer mechanism is detected in SrF2: Gd3+, Eu3+ fluoride phosphor. The phosphor is synthesized by a wet chemical method followed by reactive atmospheric process (RAP). The Powder XRD analysis shows structural purity. The photoluminescence characteristics of SrF2:Gd3+, Eu3+ phosphor is studied using the remote access of 4B8 window (VUV beamline) of the Beijing Synchrotron Radiation Facility (BSRF) China. In this paper the mechanism of Energy transfer from the Gd3+ to Eu3+ through the cross relaxation process is investigated. The down-conversion of energy from VUV (142 nm) to visible with quantum efficiency (QE) around 124% has been detected. The PL excitation and emission characteristics of the prepared phosphor advocates it as a prominent material for the applications in mercury free fluorescent lighting (MFFL) & Plasma Display Panel.

In this paper, a color-tunable light emitting diode LED with two laterally arranged single quantum wells (SQWs) is designed, and simulated. In this work, III-nitride materials are used. The structure has been numerically investigated using the ATLAS simulation software. The proposed structure has three electrodes. This gives the opportunity to emit violet (420 nm) or green (560 nm) light individually. Furthermore, it can emit simultaneously a mixture of both colors, and at a certain mixture ratio the white light is obtained with chromaticity coordinates ( x = 0.3113, y = 0.3973). The lateral arrangement of the two SQWs reduces the negative effect of photon absorption; which will give good external quantum efficiency (EQE). The structure has a big importance in the application of the solid-state lighting, especially in the white light generation.

Fire though an important component of life, the devastating effect of fire accidents is a threat to life and materials. Thus, the prevention and control of fire are becoming a serious concern. Hence, it is no wonder that fire retardant materials (FRMs) are slowly becoming ubiquitous in our daily lives. To control the fire in an unexpected fire accident or to prevent fire accidents FRMs are becoming essential requirements. To save material or life, fire retardant materials have been used for long knowingly or unknowingly. However, the understandings of chemistry and thermochemistry of materials helped for the development of efficient FRMs. Diversified materials, processing methods, and application modes have been developed, and all of them become specific depending on the nature and origin of the fire. In this regard, the inorganic FRMs form a distinct category due to their low cost, easier processing and wider choice of application mode without leaving any additional environmental burden either to land or the atmosphere. In this paper, different fire retardant materials and their properties with the abilities to tackle the fire at different temperatures are reviewed. The primary characteristics of fire and the thermal behaviours of FRMs as well as changes in behaviour/properties when FRMs are treated with certain synergistic systems are discussed. The importance of composition, morphology and structure of FRMs on the efficiency and applicability are discussed. Recent developments on the synthesis and characterisation of different types of FRMs and their composites have been elaborated. The effective applications and the commercial products based on their properties are also briefly covered. Overall, the review provides an overview of existing information on fire retardant materials in terms of their synthesis, processing, usability and limitations, with a prime attention on the process-structure-property relations of these materials.

Natural fibers have been extensively studied as a reinforcement filler in obtaining composites, replacing partially synthetic fibers. The vast majority of these materials originate from agro-industrial waste with a high content of lignin and cellulose making it a very interesting material with low cost and good mechanical properties. The purpose of the study was to obtain a composite based on alkyl ketene dimer resin, for the manufacture of sustainable packaging, made of paper by adding a 10% (w/w) con-tent of green coconut fiber and sugarcane bagasse fiber, and evaluated the impact of the filler on the mechanical behavior of the systems. The studied material was characterized from mechanical tests, such as Ring Crush Test (RCT) and Concora Medium Test (CMT) evaluating the maximum resistance supported by centimeter in the pre-pared composites, by the specimens. Through the RCT tests, with 10% w/w fibers, it was possible to verify that the fiber from sugarcane bagasse reached an increase of about 1% in the reinforcement effect compared to pure paper, and a difference of up to 2% in strength mechanics in relation to coir fiber, and CMT tests shows the reinforcement effect of the presence of sugarcane bagasse fiber, with an increase of about 3% compared to pure paper, and with a mechanical strength higher by 1% compared to coconut fiber. Therefore, the study was funneled with sugar cane fiber, varying the content by 20 and 30 % (w/w), evaluating the impact on the dispersion of this filler in the polymeric matrix and, consequently, the mechanical response of the composite with these compositions. The conclusion of the study was that the system prepared with 20% (w/w) was the one that achieved the greatest optimization of the mechanical properties, evaluated by the tests. This type of material can be applied to obtain cardboard boxes with resistance to high loads, due to the achievement of good mechanical properties.

Currently, paper pulping production from woody materials has many disadvantages due to its high energy, chemical, water consumption, methane emissions, and deforestation. However, the use of non-woody materials solves these problems. This study focused on the use of non-virgin raw material (Enset leaf fiber) in pulp and paper making. Enset leaf residues are the primary solid residues after the steam plant is used for “Kocho” processing. This leaf fiber has a lignocellulose component, converting this residue into Pulp and paper is crucial in terms of economic and waste management via the Kraft process. It has a higher fiber quality, lower energy consumption, and high recoverability of the chemical raw materials used in the process. The chemical composition of the Enset leaf fiber was analyzed using the Technical Association of Pulp and Paper. It has an excellent fiber length (2.12±1.46mm), fiber diameter (26.55±15.6µm) andacceptable rigidity coefficient (1.05±0.07), and flexibility coefficient (125.23±0.04). The maximum pulp yield was obtained at a temperature of 120°C, NaOH concentration of 8%, and 40 min cooking time off, which was 69.92% w/w. The functional groups of the Enset leaf fiber and morphological characteristics of the fiber were investigated.

Photopolymerisation of 2-Hydroxyethyl methacrylate (HEMA) through the use of N,N-Diethyldithiocarbamato-(1,2)-propanediol (DCPD) was studied. The photoinitiator DCPD was synthesized from sodium N,N-Diethyldithiocarbamate (NaSR) and 3-chloro-1,2-propanediol. For the photochemical decomposition of the C – S bond, UV light at 254 nm is used. The role of the monomer concentration, reaction time and DCPD to HEMA mol ratio on the conversion of HEMA to PHEMA were studied in this paper. It was found that percentage conversion of HEMA increased both with the rise in concentration of monomer and reaction time. Further, living radical nature of the poly2-Hydroxyethyl methacrylate (PHEMA) was ascertained by the photo block copolymerization of methyl methacrylate (MMA) with PHEMA to form PHEMA-b-PMMA. The PHEMA and PHEMA-b-PMMA were characterized by FTIR, 1H-NMR, Thermogravimetry.

According to the mechanical simulation intelligent control theory, and combining the character interaction principle, the use of genetic algorithm carries out an in-depth analysis and research for the process of PC MCU automatic control, and then the control algorithm of interactive genetic is established, finally we design the VGA structure circuit. In order to validate the validity and reliability of the model and control circuit, this paper uses the medical micro robot as the research object to the experimental analysis for the delay control circuit, so the delay characteristic curve will be obtained. By the control of time delay curve, we can be seen that the scanning delay of controllable voltage can control delay in the range of 22ps-60ps, it meets the design standards, to provide the theory reference for the mechanical bionic intelligence automatic control research.

This paper proposes a deep learning model for predicting the durability benchmark on concrete specimens. The durability benchmark on concrete samples is commonly estimated throughout the Ultrasonic Pulse Velocity measurements. This test establishes a relationship with concrete durability taken into consideration the material's homogeneity. The model proposed in this paper is feed by standard laboratory tests as input parameters, making the model a practical and efficient alternative to predict durability concrete benchmark, saving time, short-cut laboratory work, and avoiding sophisticated instrumentation use. Furthermore, it is an attractive alternative to the need for sophisticated instrumentation for estimating the Ultrasonic Pulse Velocity. The outcomes depict a high predictive accuracy about of 96% in the validation stage. In addition, the model was tested by a new dataset with different properties to demonstrate robustness and certainty in the model. Finally, the model achieves an impressive accuracy of 95.89% in the new validation dataset.

A two degree of freedom large-stroke linear FTS device was designed in this paper, the device with flexible hinges as the guidance and support part, achieved the linear degrees of freedom in X and Z. In addition, structure design and optimizationanalysis of static characteristic and dynamic characteristicresponse surface analysis of FTS device were worked as well in this paper ,then the stiffness and strength characteristics of FTS device has been greatly improved, fully meet the design requirements, achieved the desired effect.

In view of the problem of low detection precision exists in traditional quantitative detection system of broken wire for steel rope, the paper proposed a design scheme of quantitative detection system of broken wire for steel rope based on RBF neural network. The RBF Neural Network was introduced to establish the model of discerning quantitative broken steel wires. Experimental results showed that the method performed well in the identification of damage.

The Direct Iterative Surface Curvature (DISC) airfoil design method developed by NASA Langley, which is one of the inverse design methods, is robust and effective. In order to determine the target pressure distributions of airfoils, this paper used the uniformed B-spline interpolation for the parameterization of the target pressure, and a Genetic Algorithm (GA) was used to optimize the coordinates of the control points of the B-spline functions. Two cases were given to prove the effect of the DISC design method. A laminar flow airfoil was then designed using DISC after a target pressure had been determined by a GA. Results show that the DISC method based on target pressure optimization using GAs is pretty effective.

The paper studied the effect of fuel injection pressure and fuel supply advance angle on characteristics of butanol diesel blend engine.First,the results shows that when the volume ratio of butanol diesel is constant ,the fuel consumption and HC emission are the least under 20°CA.With increase of fuel supply advance angle ,the exhaust smoke emission and CO emission decreased largely under high load, but NOX emission increased largely. When the fuel supply advance angle is constant ,with the increase of volume ratio of butanol diesel ,the fuel consumption increased gradually, the exhaust smoke emission decreased largely, HC emission increased clearly, CO emission decreased largely but NOX emission increased.Third,with increase of fuel injection pressure,the exhaust smoke emission decreased largely ,NOx emission changed a little ,CO and HC emission increased largely.

An object function of hydraulic efficiency for settling tank is presented in this paper. In order to have a more efficient sedimentation tank, a new settling tank with optimum baffle and inlet configuration is presented. The hydraulic behaviors of two settling tanks with different configurations were simulated using FLUENT. The results indicated that choosing appropriate configuration of settling tank can improve the hydraulic efficiency.

Electromagnetic (EM) shielding effectiveness of fifteen woven fabrics which use different yarns as raw materials were evaluated and compared in this paper. Test samples were obtained through the change of yarn structure, the content of stainless steel filaments and process parameters. Fabric electromagnetic shielding effectiveness (SE) was analyzed in terms of the content of stainless steel filaments,fabric density and fabric tightness .The mechanism of electromagnetic shielding of worsted fabric with stainless steel filaments was further studied at different frequencies. The result has certain directive significance on developing high-performance woolen fabrics against electromagnetic radiation.

A key assumption of conventional Statistical Energy Analysis (SEA) theory is that, for two coupled subsystems, the transmitted power from one to another is proportional to the energy differences between the mode pairs of the two subsystems. Previous research has shown that such an assumption remains valid if each individual subsystem is of high modal density. This thus limits the successful applications of SEA theory mostly to the regime of high frequency vibration modeling. This paper argues that, under certain coupling conditions, conventional SEA can be extended to solve the mid-frequency vibration problems where systems may consist of both mode-dense and mode-spare subsystems, e.g. ribbed-plates.

Grinding aids to increase grinding efficiency in cement production are materials that can produce large amounts of high-quality cement in a short time by reducing surface energy by preventing particle agglomeration and improving fluidity. In the paper, a grinding aid using glycerol-waste antifreeze(GAP) is prepared and its effect on the grinding properties of clinker is investigated in contrast to that without the grinding aid. The results are as follows: The angle of repose of the cement powder added with GAP decreases as the grinding time increases (decreases by 3.8° when the grinding time is 60 minutes), indicating that it increases the flowability of the powder. On the contrary, the residual amount of 45µm sieve is also significantly reduced (4.6% decrease) and the specific surface area increases (30.5m2/kg), which results in an increase in the grinding efficiency. In the size range of 3 to 32µm, it increases the particle content, makes the particle size distribution uniform, the 7d and 28d activity index of the powder is improved by 5% and 6%, respectively, and increases the compressive strength of the cement. In addition, it is confirmed that the performance of the TEA grinding aid and the grinding aid are similar, and are very effective in terms of economy.

A novel control system of Quad-Redundant generators with the CAN-bus communication network and nonlinear PID algorithm is designed in this paper. To enhance the reliability of this power generating units, a control strategy for the multi-DSC control network of four Brushless DC Motors is presented. The hardware platform of this structure is composed of host-computer, master controller and slave-controllers, on this platform every generator could be driven independently via the CAN-bus communication network. And the principle of the nonlinear PID parameters is proposed. Using this system, the control structure of generators could be simplified and the speed of communicating could be improved. At the end of this paper, the experiment results verified that the control system is reliable, the control strategy is rational, and the system has better dynamic response.

In the research of the automobile front dash, the key of design is that acoustic need should be satisfied while losing the weight. In this paper, a structure-sound field coupling model of car body space is built. To fulfill the request, the dash panel is divided into several parts, and the sensitivity of thickness of each parts to the sound at the position of driver’s and co-pilot’s ears is calculated. Based on the sensitivity, the driver’s and the co-pilot’s parotic sound pressure is optimized while reducing the weight of front dash. The result proves that lightweight design is successful, which gives the reference to the design of the car body panels.

Carbon Fiber Reinforced Polymer (CFRP) is an anisotropic material with outstanding tensile strength in the direction of axial but low compressive strength in the direction of radial, so the radial compressive failure and sliding failure are easy to occur in the practical application of compression and hanging wires. In this paper, the influence of different parameters on radial compressive failure and sliding failure is studied. The finite element method is used to simulate and analyze the CFRP and wedge clamp to find optimum condition parameters to make the CFRP neither sliding failure nor radial compressive failure. The parameters are as follows: interference between the CFRP and the inner wedge, friction coefficient between the CFRP and the inner wedge, angle of the wedge, inner wedge material elastic modulus. The results show that the most appropriate parameter is: the interference between 0.0236mm and 0.0252mm, the friction coefficient between 0.194 and 0.206, the wedge angle is greater than 1.75° and the elastic modulus of wedge material has little influence on the compressive failure and slippage failure of the CFRP.

The Optical Fiber-based communication system has established its proficiency and inevitability towards regular progress and advancement worldwide. The most attractive wavelength for optical fiber communication is 1.55 μm, as it represents the lowest loss. The other challenging parameter ‘Material Dispersion’ gets reduced to ‘Zero’ at 1.27 μm wavelengths for conventional pure silica-based Optical Fiber. To improve the system towards a better unification between the loss and dispersion, the Dispersion Shifted Fiber (DSF) has been introduced. The Dispersion Flattened Fiber has introduced the concept of flat dispersion over a wide range of wavelengths. But the effective combination of the mechanisms to compensate for all the challenges is yet to be established properly. The said mechanisms are complex to design and implement. So, there is an immense scope to search for an alternative to get control over the loss and dispersion. At present, a fair number of material compositions of optical fiber are reported with different specifications. Our study on some of these fiber compositions has produced some interesting data towards the broader flatness and the minimum dispersion effect over a considerable range of wavelengths around the Zero Material Dispersion Wavelength (ZMDW). It helps to have more effective wavelength division Multiplexing (WDM). In this paper, we have studied different prospective options of optical fiber doping profiles to explore and propose an effective and optimized alternative among the available fiber profiles. We have studied the samples of pure SiO2 fibers along with B2O3 and GeO2 doped fibers and samples of Fluoride-based ABCY and ZBLAN glass Fibers to propose an effective combination of materials among the available options to get the optimized conjugation of loss and dispersion. Our report on the comparative study of different fiber materials has produced some effective results to have minimum material dispersion at the lowest loss wavelength to invite worldwide attention from system designers.