Search

• Pulp and paper mill sludge (PPMS) landfill sites have GHG assessment challenges. • GHG fluxes measured by chambers with (F +) and without (F-) a frame were compared. • Flux relationships up to 80 % were shown between F- and F + chambers (the standard) • Correction factors for F- chambers were built to estimate fluxes from F + chambers. • The approach can refine GHG inventories on PPMS landfill sites. Assessments of greenhouse gas (GHG) emissions in managed areas are facing various challenges. A non-flow-through, non-steady-state (NFT-NSS) chamber coupled to a frame permanently inserted into the landfilled substrates is a standard method for quantifying GHG emissions in managed areas, such as pulp and paper mill sludge (PPMS) landfill sites. Frequent measurements are needed to minimize uncertainties on GHG emission factors at the landfill site scale. However, maintaining a frame inserted into the substrates for a long time period is often impossible due to landfilling management operations. Therefore, GHG measurements using NFT-NSS chambers placed directly on substrates' surface could be an interesting option. Our objectives were to determine the relationships between CO 2 , CH 4 , and N 2 O fluxes measured with (F +) and without (F-) a frame inserted in the substrates' surface and to develop correction factors for fluxes measured without a frame. Measurements were made at different PPMS landfill sites in the province of Québec, Canada. Stronger GHG flux relationships were observed at the provincial (across sites) than the specific site scale: the variance in GHG fluxes from F- chambers explained up to 80 % of variance in fluxes from F + chambers. The measured CO 2 , CH 4 , and N 2 O fluxes in F- chambers were on average 53, 78, and 63 % lower, respectively, than those estimated by the models at provincial scale. The correction factors developed with this approach could greatly extend the number of sites where in situ GHG measurements can be done and would help refining GHG inventories at the provincial and national levels. [ABSTRACT FROM AUTHOR]

Development of low-cost, efficient, and stable oxygen evolution electrocatalysts is crucial for the conversion and storage of renewable energy. Therefore, an effective integrated heterostructure catalyst is needed to achieve a lower overpotential during oxygen evolution process. In this paper, cobalt-zinc bimetallic MOF precursors are used as templates to prepare bimetallic cobalt-based selenides with good oxygen evolution catalytic activity and stability on carbon fiber paper. Due to the high specific surface area and porous structure of the coupling structure of nanorods and polyhedra, and the strong electronic coupling between CoSe 2 and ZnSe on nanorods. CoSe 2 -ZnSe/CP exhibits excellent electrocatalytic activity in 1 M KOH solution. It only requires an overpotential of 275 mV to reach the current density of 10 mA cm-2, and the Tafel slope is 68.9 mV dec-1. In addition, after 12 h of continuous operation of CoSe 2 -ZnSe/CP, the activity decay of the catalyst is negligible. This work provides a method for the design of heterogeneous bimetallic selenide integrated oxygen evolution electrocatalysts. [Display omitted] • The CoSe 2 -ZnSe/CP catalyst is obtained by selenization of MOF precursor at high temperature. • The catalyst has unique nanorod-coupled polyhedral morphology and high specific surface area. • The strong electron coupling between CoSe 2 and ZnSe improves the oxygen evolution activity. • CoSe 2 -ZnSe/CP exhibits low overpotential, high exchange current density and fast kinetics. [ABSTRACT FROM AUTHOR]

Enzymes derived from microbial sources have gained increasing popularity in industrial applications over the past decades. Despite the high production cost, alkaline proteases have wide applications in industries such as tanneries, food production, and detergents. In recent years, there has been a shift towards utilizing natural carbon sources for cultivating microorganisms and extracting proteases in order to reduce production costs. This study aimed to investigate the biochemical and kinetic properties of protease enzymes obtained from Aspergillus niger cultivated in a paper waste medium and compare with the enzyme produced in a basal medium. Glucose is a more favorable carbon source compared to cellulose, so paper waste was pretreated with cellulose-degrading bacteria to convert cellulose into smaller carbohydrates. After the growth of A. niger in basal and combinational media, the enzymatic properties were compared between the extracted enzymes by using casein as substrate. The results demonstrated that A. niger could produce protease enzymes in the paper waste medium similar to the basal medium with more than 5-fold cost saving. The specific activity of the enzymes isolated from the basal and paper waste media was calculated to be 184.95 ± 10.56 U ml−1 and 169.88 ± 11.05 U ml−1, respectively. Carbon sources did not affect the optimum pH and temperature of the protease enzyme, which were found to be 8 and 37 °C, respectively. This study provides valuable insights into the production of alkaline protease from A. niger using a combinational medium (paper waste pretreated by cellulose-degrading bacteria), offering a cost-effective approach for industrial applications. [ABSTRACT FROM AUTHOR]

Carbon paper is one of the most widely used gas diffusion layer substrate materials due to its stable performance, relatively low cost, and easy for subsequent processing. Water-soluble phenolic resin, which is more ecologically friendly than alcohol-soluble phenolic resin, was used to prepare carbon paper as the precursor of the carbon matrix. And the effect of different resin solution concentrations on the properties of carbon paper was explored. The results showed that the graphitization, electrical conductivity and mechanical properties of carbon paper increased with the increase of resin solution concentration. When the concentration of resin solution was 20 wt%, the performance of carbon paper was relatively optimal. The graphitization of the carbon paper reached 65.45%, the porosity reached 80.74%, the resistance value at 1 MPa pressure was only 7.61 mΩ cm2, the tensile strength was 1.57 MPa, and the elastic modulus was 1210.98 MPa. [ABSTRACT FROM AUTHOR]

Carbon paper as a macroporous substrate of gas diffusion layer in proton exchange membrane fuel cells directly impacts the output performance of cells. In this study, we present a straightforward strategy to improve the overall performance of carbon paper by mixing short/long (6mm/10 mm) chopped carbon fibers at an optimal concentration of phenolic resin. The results show that incorporating longer carbon fibers can increase the porosity, conductivity, gas flux, and mechanical properties of carbon paper. The membrane electrode assembly achieved a peak power density of 1182.61 mW cm−2 at 60% RH using carbon paper with a long carbon fiber content of 40 wt% and an impregnation concentration of 10 wt%. This outperforms commercially available carbon paper. Based on electrochemical impedance spectroscopy results, it was confirmed that our carbon paper had a lower mass transfer resistance of only 32.17 mΩ cm−2 under conditions of 2 A cm−2 and 60% RH. This was due to its sparser three−dimensional network-like pore structure which was created by mixing different lengths (6mm/10 mm) of carbon fibers. This work provides new insights into preparing high−performance carbon papers. • The nature of carbon paper is regulated by mixing short/long (6mm/10 mm) CFs ratio. • The long carbon fiber contents of 20–40 wt% present better physical properties. • The optimal carbon papers can mitigate mass transfer resistance. • MEA composed of the optimal CP shows a higher power density than commercial CP. [ABSTRACT FROM AUTHOR]

A facile method is proposed in this work to prepare a carbon paper (CP) with outstanding properties by doping boron to catalyze graphitization at lower temperature. Boron was introduced into CP by impregnating carbon fiber preform into a boron/phenolic resin/ethanol solution, and then CP was obtained after the consecutive procedures of hot pressing, carbonization, and graphitization. Morphology, microstructure, composition, and physical properties of the doped and undoped CPs were thoroughly investigated via various techniques to exam the effects of boron concentration and graphitization temperature. Furthermore, the boron doped CP was fabricated into fuel cell gas diffusion layer (GDL) and membrane electrode assembly (MEA) to evaluate its performance through the single cell performance. The findings indicated CP doping with 2 wt% boron could lower the graphitization temperature by at least 200 °C. The B-doped GDL had a higher power density in comparison with the undoped GDLs made in our lab or from the commercial brands. • The innovative preparation method for carbon paper with high conductivity. • The effect of boron concentration and graphitization temperature on carbon paper. • The single cell performance of B-doped gas diffusion layer. [ABSTRACT FROM AUTHOR]

The solar photocatalytic degradation of pulp and paper mill wastewater has been reported by several scientists. However, this is the first time we are reporting for solar photocatalytic hydrogen production from pulp and paper mill wastewater and simultaneous degradation of pollutants. In this work, CuO based photocatalysts and novel square type photocatalytic reactor of 5 L capacity were used. The result shows that the prepared photocatalysts are solar active, efficient in hydrogen recovery and pollutant degradation from the pulp and paper wastewater. The effects of catalyst loading, sacrificial agent, pollutant removal efficiency and stability check were investigated. At 0.25 g/L of CuO/Fe 2 O 3 , 0.2 M of sacrificial agent (Na 2 SO 3 2−) and hydrogen yield of 1000 mL from 1000 mL of wastewater was achieved. The removal efficiency of TSS, TDS, BOD, COD, turbidity and TOC are around 70, 50, 60, 65, 70 and 45% respectively. Reusability study revealed that CuO/Fe 2 O 3 was chemically stable and could be reused successively (five cycles) without significant changes in its photoactivity and intrinsic properties. [Display omitted] • Visible light active CuO mixed with novel metal oxides were employed. • Hydrogen recovery from black liquor, paper mill wastewater were 1000 mL/h/L and 850 mL/h/L. • Efficiency of degradation of pulp & paper wastewater chemicals were around 50–70%. • AcHieved high recovery of hydrogen from pulp & paper wastewater. [ABSTRACT FROM AUTHOR]

The Proton Exchange Membrane Fuel Cell (PEMFC) performances are strongly impacted by the compression of the Gas Diffusion Layer (GDL). Despite its fibrous microstructure, this material is usually considered as a continuous medium and characterized with uniform loading. However, the GDL is subjected to a heterogeneous compression onto rib/channel patterns in the fuel cell assembly. In the present study, a complex behavior of the GDL response is experimentally revealed when the material is loaded with a rib/channel pattern, compared to uniform compression. The tests are simulated by finite element modeling using a classical strain-dependent elastic law, using parameters fitted from uniform compression experiments. It is shown that the numerical results do not reproduce the effect of pattern observed experimentally. Hypotheses to interpret these results involve mechanisms at the fiber microscale including fiber fracture, cross-link breakage and fiber rearrangement, which are exacerbated by larger material deformation caused by the heterogeneous loading. • Unexpected impact of rib/channel patterns on GDL compression. • Experimental investigation of the effect of rib/channel width on GDL deformation. • Numerical study with classical model unable to reproduce experimental results. • Interpretations based on mechanisms at the fiber microscale. [ABSTRACT FROM AUTHOR]

• The PBAT/PLA coated paper shows high methane yield under AD condition. • Plastic film residues remain after the digestion of PBAT/PLA coated paper. • The decrease of hydrophobicity for PBAT/PLA bags is due to the formation of PLA monomers. • The bacterial community shows difference between PBAT/PLA coated paper and bags. • Methanoculleus is enriched on the plastic surface under mesophilic AD. Poly (lactic acid) (PLA) and Poly(butylene adipate-co-terephthalate) (PBAT) are two of biodegradable plastics with the highest production capacities in 2021. Bioplastic waste management can be easily integrated with organic waste management, especially when bioplastics are used as food packaging material, since they are potentially biodegradable. The aim of this study was to assess the biodegradability of biodegradable polymer-coated paper (BPCP) and bioplastic bags made from PBAT/PLA blend during mesophilic and thermophilic anaerobic digestion (AD) and to reveal the changes in the physicochemical properties of the bioplastics. BPCP obtained 155 NmL-CH 4 /g VS and 307.3 NmL-CH 4 /g VS under mesophilic and thermophilic conditions, respectively, but left bioplastic film residues. The bioplastic bags did not exhibit significant biodegradation during the AD processes. 1H NMR results indicated that the ratio of PLA to PBAT decreased significantly after AD of the BPCP film and that PLA monomers were formed from the bioplastic bags, leading to a decrease in the hydrophobicity on the surfaces of the materials. Methanoculleus was found to be enriched on the bioplastic surface after mesophilic AD. From the perspective of coupling bioplastic waste management with the food waste management, the incorporation of BPCP into the AD reactor not only enhances system stability and methane production to a greater extent than biodegradable plastic bags but also raises concerns regarding the residual biofilm when utilizing the digestate for direct land applications. [ABSTRACT FROM AUTHOR]

This paper describes the fabrication and characterization of porous SiC ceramics derived from highly-filled preceramic papers. The SiC ceramics were obtained by spark plasma sintering of stacked preceramic papers at temperatures of 2100 and 2200 °C under pressures of 5–60 MPa for 10 min. The microstructure and phase composition were analyzed by scanning electron microscopy and X-ray diffraction, respectively. Gas permeation tests were performed using hydrogen permeation cell at room temperature. It is revealed that the porosity of sintered SiC can be varied from 9 to 45 % depending on the sintering parameters. The shrinkage of the materials during spark plasma sintering occurs in four stages. The linear shrinkage value of the material increases from 7 to 47 % at 2100 °C and from 20 to 50 % for the samples sintered at 2100 and 2200 °C, respectively. Correlation dependencies between porosity and mechanical properties of the fabricated SiC were established. The obtained porous SiC ceramics exhibit high bending strength of 165 MPa and gas permeation flux of 78 molH 2 /m2/s at the porosity of 36 % that make it suitable for ceramic-based membranes. [ABSTRACT FROM AUTHOR]

As a H 2 O 2 electrochemical biomimetic enzyme sensor, the stability, repeatability and sensitivity of hemin-based composites are closely connected with the loading of hemin on high-performance matrix. Herein, polypyrrole/paper-derived carbon (PPy/PC) nanocomposite was used for the construction of a hemin-based non-enzymatic sensor to detect H 2 O 2. Where the poplar wood is used to obtain crude cellulose through a straightforward paper-making process. This crude cellulose is then subjected to pyrolysis to yield the desired paper-based carbon material. The hemin-decorated PPy/PC was demonstrated possessing remarkable electrocatalytic activity for H 2 O 2 reduction, and the possible mechanism of the reactions was discussed. The electrochemical sensor, utilizing the H-PPy/PC composite, achieved a low detection limit of 30 ​nM, along with enhanced selectivity and stability under optimized conditions. The favorable results observed can primarily be attributed to the superior electrochemical performance of PPy/PC, as well as its unique 3D interconnected structure. This structure effectively impedes the self-dimerization of hemin, thereby ensuring the generation of active catalytic species. [ABSTRACT FROM AUTHOR]

Present work covers the treatment of lignin enriched paper industry wastewater (LEPIW) using electrocoagulation (EC) process with stainless steel (SS) electrodes. In this study, EC operation is optimized in term of % chemical oxygen demand (COD) removal and treatment cost (USD/kg COD removed). Single parameter study has been performed to study the effect of process parameters on % COD removal and treatment cost. Central composite design (CCD) of design of expert (DOE) has been used to corelate the input (time, initial COD, solution pH and current) and output parameters (% COD removal and treatment cost). Single parameter study states that maximum % COD removal of 84.4 & 77% is achieved in 40 & 60 min for initial COD:500 &1000 mg/L while 74, 66.7 & 58% can be achieved in 100 min for initial COD of 2000, 3000 & 4000 mg/L, respectively under optimum condition (solution pH:7, current: 1 A). Cost analysis summarizes that treatment cost decreases with increase in initial organic load (2.036, 2.075, 1.554, 1.247 & 1.127 USD/kg COD removed for initial COD of 500, 1000, 2000, 3000 & 4000 mg/L, respectively) at optimum condition. The caloric study states 2.31and 3.25 J/mg can be generated from the sludge and scum produced during EC process. DOE software suggests − 6.66–6.79% & − 16.73–7.95% error between experimental and designed value for % COD removal and treatment cost. [Display omitted] • COD removal range 84.4–58% is noticed for initial COD 500–4000 mg/l. • Treatment time increases from 60 to 100 min for initial COD range of 500–4000 mg/l. • Treatment cost 1.12–2.07 USD/kg COD R is noted for COD range of 500–4000 mg/l. • 2.31 and 3.25 J/mg energy is found from generated sludge and scum respectively. • Model predicts − 6.66–6.79% & − 16.73–7.95% error for COD removal & treatment cost. [ABSTRACT FROM AUTHOR]

The large-scale development of flexible electrode is urgently needed for water electrosplitting. Herein, the common and low-cost filter paper (FP) is utilized as the substrate to adjust the flexible property of the catalytic electrode. Through an electroless plating method, the NiFeP alloys were deposited onto the filter paper, which acted as the flexible and self-supported electrode for hydrogen evolution reaction (HER) and oxygen evolution reaction (OER). The resultant NiFeP@FPs require low overpotentials of 158 mV for HER and 282 mV for OER to deliver a current density of 10 mA cm−2, and exhibit a good stability of 30 h in 1 M KOH. The synergistic effect of Fe–Ni sites regulates electron structure and boosts the catalytic activity. Benefited from good hydrophilicity and interlaced fiber structure of filter paper, electrolyte penetration and electron transfer in the sample are promoted. The assembled two-electrode electrolyzer only requires 1.814 V to achieve 100 mA cm−2 for overall water splitting and shows excellent stability. This work provides a new strategy for the development of flexible and efficient electrodes for water splitting, which advances the development of wearable electronic devices. [Display omitted] • The flexible filter paper-based electrode was successfully synthesized. • The good hydrophilicity and porous structure facilitated electrolyte permeation. • The sample required low overpotentials of 158 mV for HER and 282 mV for OER. • The two-electrode electrolyzer provided 100 mA cm−2 at a low voltage of 1.814 V. [ABSTRACT FROM AUTHOR]

Aerogel composites reinforced by fibers have found extensive applications in the field of thermal insulation and energy conservation. However, the composites are hindered by their high infrared radiation transmittance and weak interface adhesion in practical applications. Herein, we designed and prepared a novel thin composite called 'fiber/whisker/aerogel paper' (SWAP) with a thickness of less than 1 mm. The SWAP integrated SiC nanowhiskers (SiC nw) as opacifiers and ultrafine SiO 2 fibers as reinforcement, fabricated through wet manufacturing and sol-gel process. The 'fiber/aerogel paper' (SAP) and SWAP exhibited low thermal conductivity at room temperature, measuring 0.025 W/(m·K) and 0.033 W/(m·K), respectively. Additionally, they exhibited low densities of 0.195 g/cm3 and 0.225 g/cm3, respectively. Notably, SWAP exhibited excellent high-temperature insulation performance, primarily due to its low infrared transmittance (50% at 3 μm). The incorporation of SiC nw and ultrafine SiO 2 fibers collectively enhanced the interfacial adhesion with the aerogel matrix even amidst rigorous testing (weight loss less than 3%). SWAP also demonstrated flexibility, high thermal stability, hydrophobicity, and flame resistance. Furthermore, a comprehensive investigation into the performance variations and influencing g factors of the material was conducted under different heat treatment conditions. This research provides guidance for the application of such materials under high temperatures. [ABSTRACT FROM AUTHOR]

The ZrO 2 fiber paper exhibits excellent thermal insulation properties, however, its limited mechanical strength and insufficient thermal stability hinder its widespread applications. The composite fiber papers, using mullite fibers possessing a high aspect ratio and exceptional thermal stability combined with ZrO 2 fibers, were fabricated via a vacuum-assisted filtration method. This method involved the successive stacking of composite fibers with alumina sol, using vacuum-induced directed water flow to create a layered structure reminiscent of nacre. The layered structure of the nacre, which demonstrates remarkable strength and hardness, has also served as a source of inspiration for the architectural design of the fiber paper. The tensile strength of pure ZrO 2 fiber paper was significantly enhanced by the addition of 7 wt% mullite fibers, resulting in a remarkable increase to 0.1805 kN/m. The paper exhibited exceptional resistance to bending, maintaining 96 % of its bending strength even after undergoing 100 cycles. The thermal shrinkage of the composite paper, containing 15 wt% mullite fibers, was reduced from 17.75 % observed in pure ZrO 2 fiber paper to a mere 1.32 % after undergoing heat treatment at a temperature of 1300 °C for 2 h. The composite paper, measuring 5 mm in thickness and consisting of 7 wt% compositions, displayed exceptional thermal insulation properties when exposed to a hot side temperature of 1370 °C. It effectively insulated temperatures up to approximately 1000 °C. [ABSTRACT FROM AUTHOR]

Black liquor (BL) bioconversion into valuable by-products is essential to develop a bioeconomy strategy; however, its furfural content hinders microbial fermentation activities. Hence, this study utilizes paper mill sludge (PMS) to provide extracellular enzymes, furfural-degrading microbial consortia, and electron donor required for promoting the BL hydrogenesis potential. Three up-flow anaerobic sequential batch reactors (UASBRs) are fed with PMS (UASBR1), BL (UASBR2), and PMS + BL (UASBR3) and operated in parallel at 15 min fill, 72 h reaction, and 4 h settling. The UASBR3 achieves the maximum volumetric H 2 of 1.483 ± 0.088 L/L/d and H 2 yield of 2.06 ± 0.12 mol/mol glucose, which drops by 88% in UASBR2 and 24% in UASBR1. The insufficient H 2 productivity values in UASBR2 could be due to a lack of nutrients availability (C:N = 440:1 and C:P = 19:1), higher furfural concentration (2116 ± 422 mg/L), and involvement of the butyrate fermentation pathway. The synergetic effect between PMS and BL overcomes these limitations and enriches the fermentation medium with Proteobacteria phyla (22.8%) and Acinetobacter sp. degrading furfural (6.1%). The microbial community at the phylum level (e.g., Proteobacteria , Firmicutes , and Actinobacteria) in UASBR3 maximizes the migration of electrons (e−eq = 9.34 ± 0.54%) towards efficient H 2 formation. [Display omitted] • Paper mill sludge (PMS) mitigated inhibitory effect of furfural in black liquor (BL). • PMS improved H 2 yield from the BL by 8.3-folds and accounted for 2.1 mol/mol glucose. • e– eq transferred to H 2 was 9.3% in the PMS:BL, 7.4% in PMS, and 1.27% in BL. • Acinetobacter degrading furfural (6.1%) was abundant with PMS addition. • Bacilli (8.9%) and Clostridia (5.4%) was dominant in the hydrogenesis of PMS:BL. [ABSTRACT FROM AUTHOR]

A noble-metal-free bifunctional electrocatalyst with outstanding activity and stability is of great importance for the development of rechargeable zinc-air batteries (ZABs). Herein, we employed a facile strategy to fabricate nitrogen-doped NiCo 2 O 4 nanostructures on carbon paper as a binder-free air cathode for rechargeable ZABs. An optimized process of nitrogen plasma treatment has enhanced the electrical conductivity of the metal oxide and induced abundant active sites into the crystal structures, resulting in enhanced electrocatalytic activities toward oxygen evolution reaction (OER) and oxygen reduction reaction (ORR). Notably, mild plasma treatment leads to efficient N doping while the morphology and specific surface area of the catalyst both remain unchanged. The air cathode with NiCo 2 O 4 doped with nitrogen in 2 min plasma treatment and integrated into a zinc-air battery with liquid electrolyte provided a small charge-discharge voltage gap and distinguished cycling stability superior to the air cathode with noble-metal catalyst counterparts. Furthermore, the solid-state zinc-air battery with this material displays excellent stability with just a small increase of the charge-discharge voltage gap over 20 h of operation. This work illustrates the promising potential of plasma treatment in the fabrication of high-performance catalysts. • N-doped NiCo 2 O 4 was prepared by hydrothermal method and N 2 plasma treatment. • Mild plasma treatment leads to efficient N doping in NiCo 2 O 4. • NiCo 2 O 4 with N 2 plasma treatment of 2 min exhibits excellent OER/ORR performances. • N–NiCo 2 O 4 -2 min worked as a binder-free air cathode in Zn-air batteries. [ABSTRACT FROM AUTHOR]

The importance of shared decision making (SDM) for informed consent has been emphasised in the updated regulatory guidelines. Errors of completion, legibility and omission have been associated with paper-based consent forms. We introduced a digital consent process and compared it against a paper-based process for quality and patient reported involvement in shared decision making. 223 patients were included in this multi-site, single centre study. Patient consent documentation was by either a paper consent form or the Concentric digital consent platform. Consent forms were assessed for errors of legibility, completion and accuracy of content. Core risks for 20 orthopaedic operations were pre-defined by a Delphi round of experts and forms analysed for omission of these risks. SDM was determined via the 'collaboRATE Top Score', a validated measure for gold-standard SDM. 72% (n = 78/109) of paper consent forms contained ≥1 error compared to 0% (n = 0/114) of digital forms (P < 0.0001). Core risks were unintentionally omitted in 63% (n = 68/109) of paper-forms compared to less than 2% (n = 2/114) of digital consent forms (P < 0.0001). 72% (n = 82/114) of patients giving consent digitally reported gold-standard SDM compared to 28% (n = 31/109) with paper consent (P < 0.001). Implementation of a digital consent process has been shown to reduce both error rate and the omission of core risks on consent forms whilst increasing the quality of SDM. This novel finding suggests that using digital consent can improve both the quality of informed consent and the patient experience of SDM. • The paper consent process is associated with errors and omissions of core risks. • A digital consent process improved error rate and omission rate of core risks. • Patients reported a higher level of shared decision making with a digital process. • Documentation of consent can be reliably standardised with an electronic record. [ABSTRACT FROM AUTHOR]

Ni-doped WC/Mo 2 C composites for hydrogen evolution reaction (HER) were synthesized in situ grown on carbon fiber paper (CFP) by molten salt method in argon at 1000 °C for 6 h, named as Ni-xWC-y/2Mo 2 C@CFP. The effects of different W/Mo molar ratios (3:1, 2:1, 1:1, 1:2, 1:3) on the phase composition, microstructures, and HER performances were investigated. The results showed that the W/Mo molar ratio had a synergistic effect in HER of Ni-doped WC/Mo 2 C composites, and as W/Mo molar ratio at 1:1, the composite presented the best electrocatalytic activity. Meanwhile, its surface appeared to have a wrinkle-like structure, and the biphasic heterostructure emerged at the intersection of the dual-phase WC and Mo 2 C lattices. The introduction of a biphasic heterostructure could promote charge transfer and improve HER efficiency. Predictably, the electrocatalysts with the optimal W/Mo molar ratio 1:1 exhibited the best hydrogen evolution performance, needed only 43.7 mV overpotential to reach 10 mA cm−2 current density with a Tafel slope at 21.3 mV dec−1. In this work, the high-efficiency electrocatalysts of Ni-doped 1WC-1/2Mo 2 C@CFP have been prepared, which provides an insight into theoretical research of composite carbon-based electrocatalysts. [ABSTRACT FROM AUTHOR]

To solve the durability problem caused by carbon corrosion in the porous carbon paper gas diffusion layer (GDL) of proton exchange membrane fuel cell (PEMFC), a Cr 7 C 3 ceramic coating on porous carbon paper by molten salt method was prepared. The obtained Cr 7 C 3 coating is dense and shows good adherent with the carbon paper. Based on the corrosion resistance testes, it is concluded that the Cr 7 C 3 coated carbon paper can keep high chemical stability in the long-time acid immersion accelerated corrosion tests and simulated cathodic proton exchange membrane fuel cells environment. The carbon paper with Cr 7 C 3 coating shows a small current density with a value of about 1.1 × 10−5 A cm−2 in the potentiostatic polarization test under 1 M H 2 SO 4 + 2 ppm HF at 70 °C and1.4 V SCE for 72 h. Meanwhile, the resistivity of carbon paper with Cr 7 C 3 coating prepared is 30% lower than that of pure carbon paper, and the conductivity is 1.5 times that of pure carbon paper. [ABSTRACT FROM AUTHOR]

This research investigated the hydrogen production and energy conversion from automobile shredder residues (ASRs) and paper mill sludge (PMS) co-gasified in a full-scale fluidized bed gasification plant. The results obtained from full-scale tests provided important information on the feasible assessment of ASRs-to-energy and the selection of alternative technologies for ASRs. Based on the analysis results of produced gas composition, H 2 , CO, and CH 4 composition produced from paper-mill sludge gasified were 4.17%–6.01%, 3.08%–4.32%, 1.71%–2.4%, respectively. Another C 2 gas composition ranged from 2.9% to 3.59%. The heating value of produced gas ranged between 1.64 MJ/Nm3 and 2.18 MJ/Nm3. In the case of 10% ASR addition, the heating value of produced gas was slightly increased to 1.84 MJ/Nm3-2.34 MJ/Nm3. The dioxin emission concentration of flue gas was approximately 0.064 ng I-TEQ/Nm3. It can comply with Taiwan regulation thresholds. The dioxin leaching concentrations of residues derived from gasification were also in compliance with regulation limits by the TCLP test. Meanwhile, in the case of 10% ASRs addition, the dioxin equivalence concentration of gasified residue was nearly 0.002 ng I-TEQ/Nm3. It was far below the current regulation standard limit. In summary, the results of this research have proved the performance of ASRs-to-energy by co-gasified with paper mill sludge using a full-scale gasification plant. The results obtained from this research also provided the information for selecting ASRs alternative technologies and operating full-scale gasifiers in the future. [Display omitted] • This study has confirmed the feasibility of co-gasification of calcium-rich PMS and chlorine-rich ASRs. • Adding 5%–15% of ASRs can maintain the regular operation of the full-scale commercial gasifier. • The synthesis gas has a composition of 4.91 vol% H 2 and 2.06 vol% CO, with a LHV of 1.93 MJ/Nm3. • The HCl emission could comply with regulation thresholds in co-gasification. • Dioxin reformation reduced significantly in co-gasification of PMS and ASRs. [ABSTRACT FROM AUTHOR]

Alumina-based multilayer laminates with layers of varied porosities and ceramic fiber reinforcements, which can be achieved by including paper-derived ceramic layers, are interesting candidates for chemically stable and thermal shock resistant materials. In order to investigate the complex sintering behavior of these laminates, the sintering of each alumina layer contained within a laminate, each one with its individual sintering anisotropy and sintering shrinkage, has to be considered separately. For this purpose, sintering curves are determined by dilatometry measurements, serving a consecutive examination by an analytical model. Modeling parameters specific to each layer, are applied in finite-element-type sintering simulations for symmetrical multilayer laminates. Differences in the sintering shrinkages may cause internal stresses at layer interfaces and, in turn, may influence the thermal and mechanical properties of multilayer laminates after sintering. Accordingly, the prediction of developing internal stresses within alumina-based multilayer laminates by the presented sintering simulations is a key aspect of this study. [Display omitted] • Individual laminates sintering dilatometry. • Anisotropic sintering assessment by analytic modeling. • Finite element simulation of multilayer laminates sintering. [ABSTRACT FROM AUTHOR]

Lower-limb strength measures can enhance falls risk assessment but due to the lack of clinically applicable methods, such measures are not included in current screening. The enhanced paper grip test (EPGT) is a simple-to-use and cost-effective test that could fill this gap. However, its outcome measure (EPGT force) has not yet been directly linked to the risk of falling. Is the EPGT a good candidate for falls risk screening in older people in the community? Seventy-one older people living independently in the community were recruited for this prospective observational study (median age 69 y, range 65y-79y). Lower-limb and whole-body strength were assessed at baseline using the EPGT and a standardised hand-grip method respectively. Incident falls were recorded monthly for a year through follow-up telephone conversations. The capacity of individual strength measures to predict falls and to enhance an established falls risk assessment tool (FRAT) commonly used by UK's national health service (NHS) was assessed using binomial logistic regression. The analysis was repeated for the subset of participants without history of falling at baseline (prediction of first-ever falls). Increased EPGT force and increased symmetry in strength between limbs were significantly associated with reduced risk of falling. Compared to the NHS-FRAT, the EPGT correctly classified more people (73% vs 69%), it achieved higher sensitivity (56% vs 26%) and higher negative predictive value (76% vs 68%). Complementing the NHS-FRAT with the EPGT produced a more comprehensive model that correctly classified 91% of participants and achieved 98% specificity, 81% sensitivity, 89% negative and 96% positive predictive value. Replacing the EPGT with hand-grip strength consistently undermined prediction accuracy. The EPGT remained highly accurate when focused on the prediction of first-ever falls. The EPGT can substantially enhance falls screening in the community. These results can also inform effective personalised strength exercise interventions. • The enhanced paper grip test (EPGT) accurately predicted the risk of falling. • The EPGT can enhance community screening for falls (recurrent and first-ever). • Higher EPGT force is significantly associated with reduced risk of falling. • Higher strength asymmetry between limbs also decreases the risk of falling. • These results can guide effective personalised strength exercise interventions. [ABSTRACT FROM AUTHOR]

Pen-on-paper pain drawing are an easily administered self-reported measure that enables patients to report the spatial distribution of their pain. The digitalization of pain drawings has facilitated the extraction of quantitative metrics, such as pain extent and location. This study aimed to assess the reliability of pen-on-paper pain drawing analysis conducted by an automated pain-spot recognition algorithm using various scanning procedures. One hundred pain drawings, completed by patients experiencing somatic pain, were repeatedly scanned using diverse technologies and devices. Seven datasets were created, enabling reliability assessments including inter-device, inter-scanner, inter-mobile, inter-software, intra- and inter-operator. Subsequently, the automated pain-spot recognition algorithm estimated pain extent and location values for each digitized pain drawing. The relative reliability of pain extent analysis was determined using the intraclass correlation coefficient, while absolute reliability was evaluated through the standard error of measurement and minimum detectable change. The reliability of pain location analysis was computed using the Jaccard similarity index. The reliability analysis of pain extent consistently yielded intraclass correlation coefficient values above 0.90 for all scanning procedures, with standard error of measurement ranging from 0.03% to 0.13% and minimum detectable change from 0.08% to 0.38%. The mean Jaccard index scores across all dataset comparisons exceeded 0.90. The analysis of pen-on-paper pain drawings demonstrated excellent reliability, suggesting that the automated pain-spot recognition algorithm is unaffected by scanning procedures. These findings support the algorithm's applicability in both research and clinical practice. [ABSTRACT FROM AUTHOR]

In this study, practical application for the industrial-scale hydrogen evolution reaction (HER) process is established using sustainable Cu 2 CoSnS 4 embedded in paper-working electrodes. The Cu 2 CoSnS 4 is produced using a solvent-free solid-phase approach. The effect of a wide pH range of electrolytes on working electrodes for hydrogen evolution reactions is also investigated. The Cu 2 CoSnS 4 embedded paper-working electrodes exhibit goodelectrocatalytic activity for hydrogen evolution reaction with low overpotential values of 233, 310, and 261 mV vs RHE at 10 mA/cm 2 in 0.5 M H 2 SO 4 ,1 M KOH, and 1 M PBS, respectively. These designed electrodes exhibit high double-layer capacitance and electrochemical surface area for a wide pH range. In acidic, alkaline and neutral environments, the catalyst-embedded paper electrodes explicit high turnover frequencies of 2.15 s−1, 2.75 s−1, and 2.11 s−1, respectively. The temperature-dependent hydrogen evolution reaction is studied to calculate the activation energy of the cathodic electrode. Utilising chrono-amperometry for about 118 h in an acidic media, which shows that electrodes have a high degree of stability. In comparison to other previously reported work on catalyst-embedded electrodes, the Cu 2 CoSnS 4 embedded paper-working electrodes offer excellentpotential for HER activity across a wide pH range and are suitable for industrial application. • Cu 2 CoSnS 4 embedded paper working electrodes are developed for hydrogen generation. • The electrodes exhibit universal pH hydrogen evolution reaction. • Electrodes shows excellent stability upto 40hr for continuous hydrogen generation. • The electrode displays good stability at current density more than 200 mA/cm2. [ABSTRACT FROM AUTHOR]

A variety of real-world situations take the form of repeated principal-agent problems with binary evaluation. I evaluate the principal's optimal evaluation effort and quality threshold for acceptance in the setting of dynamic agency with binary evaluation, focusing specifically on the evaluation by a top academic journal of papers submitted by economists. In the baseline model, the journal should statistically discriminate in favour of high-status economists, by setting an acceptance threshold that declines with their prior estimate of the economist's quality, while evaluation effort should likely increase with perceived author quality, as this provides incentives for authors to exert more effort, which is particularly valuable from the highest-quality authors. However, if a first good publication is more valuable than subsequent publications by the same economist, acceptance thresholds will tend to increase after publication success, relative to the threshold that would have followed a rejection. • Considers repeated principal-agent problem with binary evaluation. • Specifically, evaluation by a top academic journal of papers submitted by economists. • Journal should statistically discriminate in favour of high-status economists. • Acceptance threshold declines with prior estimate of economist's quality. • But threshold could increase after publication if first publication is most valuable. [ABSTRACT FROM AUTHOR]

Paper-type gas diffusion layer (GDL) plays the role of structural support, mass transport, electron and heat transfer in the fuel cell. The deformation and fracture behavior of paper-type GDL directly determines its physical characteristics. In this paper, we obtained the distribution function of fiber length among intersections using statistical analysis. Based on the bending theory and fracture analysis, the deformation model and the maximum allowable pressure criterion of paper-type GDL are established. The deformation modulus is related to the modulus and the initial volume fraction of carbon fiber, with an ideal value of 1.4 MPa. The tensile fracture is the main form of fiber fracture. The maximum allowable pressure is related to the expected fracture probability, the strength and the initial volume fraction of carbon fiber. The residual strain increases and the deformation modulus decreases with load range, which means that the strength of the paper-type GDL is weakened when residual strain occurs. [Display omitted] • The fiber length between intersections obeys exponential distribution function. • The compression deformation model of paper-type GDL is established. • The maximum allowable pressure criterion for the paper-type GDL is obtained. [ABSTRACT FROM AUTHOR]

This study presents a novel method for synthesizing hierarchical porous zinc oxide (ZnO) nanostructures by thermally decomposing green-synthesized hydrozincite. The hydrozincite was prepared at room temperature using zinc acetate dihydrate and calcium carbonate (CaCO 3) in cellulose printing papers as the precipitating agent. The resulting ZnO particles exhibit a distinctive flower-like morphology, consisting of porous nanosheets composed of interconnected nanoparticles. The average crystallite size of the hierarchically structured zinc oxide nanoparticles, as determined via X-ray diffraction Rietveld refinement method, was found to be 18.8 nm when calcined at 500 °C. However, with increasing calcination temperature to 600, 700, and 800 °C, the average crystallite size also increased to 24.3, 30.4, and 47.2 nm, respectively. The ZnO synthesized at temperatures of 500 °C, 600 °C, and 700 °C exhibits higher electrocatalytic activity toward the hydrogen evolution reaction (HER) compared to both the ZnO synthesized at 800 °C and commercial ZnO. This enhanced performance can be primarily attributed to the nanosized ZnO particles, which provide a substantial surface area, high accessibility of active sites, and fast charge transfer kinetics. In terms of photocatalytic activity, all the samples show HER improvement under the UV light irradiation, attributed to the generation of photoexcited charge carriers. The ZnO synthesized at 800 °C and the commercial ZnO exhibit greater enhancements in photocatalytic activity compared to the other samples. This implies that larger solid particles with fewer nanopores result in a greater exposed surface area for UV-light absorption. The hierarchically structured ZnO nanoparticles demonstrate promising electrocatalytic and photocatalytic activities, as well as stability, opening up potential applications in various fields, including energy conversion and environmental remediation. [ABSTRACT FROM AUTHOR]

Paper crumb (PC) is a type of paper sludge residue from the wastepaper recycling industry. It is a by-product from the various fiber purification stages that is particularly composed of short cellulose fibers, lignin, organic compounds and inorganic filler residues. Despite representing a reject material for the paper recycling sector, this feedstock can be turned into a bioresource to enable cross-sector industrial symbiosis in the form of a more sustainable concrete, hence an opportunity for novel Net Zero supply chains. This study sought to valorise the PC by the sequential anaerobic digestion to produce methane (CH 4) from the organic compounds, followed by utilization of the digestate as a water replacement in concrete. The 21-day digestion of PC yielded 163 ml CH 4 per gram volatile solids and the resulting digestate improved concrete compressive strength up to 50% water replacement grade, meeting the requirements for structural grade (C32/40) applications with substitution grades up to 50% and 25%, with and without the addition of plasticiser respectively. In a minor capacity, the digestate reduced workability of the concrete mix, however we demonstrate this issue can be resolved by the addition of plasticiser or increased water to cement ratios. The admixture addition is important to facilitate pumpability on site and ensure satisfactory compaction. This study highlights the potential of anaerobic digestate as a concrete supplement (additive), which would improve the sustainability of both the construction and the paper sector. [Display omitted] [ABSTRACT FROM AUTHOR]

• Water retention curves (WRCs) of municipal solid wastes (MSWs) • Hysteresis of WRCs of MSWs with decomposition. • Effects of decomposition and paper content on the WRCs. • Unsaturated hydraulic and gas conductivity of MSWs. This paper investigates the drying and wetting water retention curves (WRCs) of municipal solid wastes (MSWs) with different paper contents, dry unit weights and degrees of biodegradation (DOBs). Fresh synthetic samples were prepared based on the field composition of the MSWs at Mugga Lane Landfill, the Australian Capital Territory (ACT), Australia. The degraded samples were prepared in simulators with MSWs of different initial dry unit weights and decomposition periods with leachate recirculation. The water retention curves (WRCs) of the MSWs were determined using pressure plate tests, in both drying and wetting phases. The outflow from MSWs was analysed using Gardner's method to obtain the unsaturated hydraulic conductivity. The results indicate that the WRCs of the MSWs are greatly affected by the DOB, paper content and dry unit weight. When DOB < 30 %, as DOB increases, the air-entry pressure of MSWs with paper increases, and the residual moisture content decreases regardless of paper content. With DOB > 30 %, the air entry pressure and residual water content depend on the balance between organic matter and highly decomposed organic constituents. The paper content affects the WRCs of MSWs due to its water retention capacity and change in the particle size distribution with decomposition. The increase in the dry unit weight of MSWs significantly increases the air entry pressure and residual moisture content, similar to the borehole samples with combined effects of biodegradation and increase in stress level from literature. Hysteresis effects have been observed during the drying and wetting of MSWs. The hysteresis of WRCs increases with the paper content and DOB. [ABSTRACT FROM AUTHOR]

Persulfate is a potential oxidant in direct liquid fuel cells (DLFCs), and the commercial carbon paper (CP) can directly serve as the cathode due to strong oxidizability of persulfate. However, the poor catalytic activity and low specific surface area of CP limit the electrode performance. Herein, a defect-enriched, pyridine-N-dominated and self-standing carbon paper electrode with abundant carbon nanosheets is successfully prepared by hydrothermal treatment combined with in-situ electrochemical exfoliation. Benefitting from the integrated structure, plentiful defects and high-content pyridine-N dopants of the prepared electrode result in the superior electrocatalytic activity and long-term stability in persulfate reduction reaction. Remarkably, a membraneless DLFC with the prepared electrode as cathode and persulfate as the oxidant acquires prominent cell performance and extremely high open circuit voltage of 2.13 V. The maximum power density of the DLFC achieves 241.0 mW cm−2, far higher than those of the previously reported similar membraneless DLFCs. A three-dimensional computational model for the DLFC is developed, which is help to reveal the importance of improving the reaction kinetics and electrical conductivity for the cathode with persulfate as oxidant. A facile approach for in-situ preparation of highly N-doped CP electrode is provided to yield outstanding cell performance for low-cost DLFCs. [Display omitted] • A facile way to introduce high-content nitrogen on carbon paper is proposed. • Massive defective sites, carbon nanosheets and pyridine-N dopants are introduced. • N doping enhances charge transfer and electrocatalytic activity of the electrode. • Effects of hydrothermal duration and precursor concentration are discussed. • The N-doped cathode yields the outstanding cell performance for low-cost DLFC. [ABSTRACT FROM AUTHOR]

• KAl(SO 4) 2 ·12H 2 O and gelatin in the alum-glue solution play devastating and relatively beneficial roles in paper durability respectively. • A 23 full factorial experiment was performed to explore the effects of KAl(SO 4) 2 ·12H 2 O (denoted as alum), gelatin (denoted as glue), and water contents on rates of paper degradation and color changes, by measuring rates of changes in DP [ k Δ(1/DP)], lightness and b* (k ΔL and k Δb) respectively. • Alum is mainly responsible for lightness decrease of the treated papers,. • Glue content (gelatin) plays a primary role in paper yellowing. In the traditional Chinese conservation mounting process, it is well acknowledged that the alum-glue solution, composed of potassium aluminum sulfate [KAl(SO 4) 2 ·12H 2 O], gelatin, and water, is commonly used for paper sizing. In this study, its adverse effects when prepared in different ratios on the contemporary Xuan paper are explored, demonstrating certain negative influences on material properties and paper durability. We primarily characterized an extra-pure Xuan paper as a reference sample. Then, a 23 full factorial experiment was designed and performed to explore the effects of the three factors, i.e., KAl(SO 4) 2 ·12H 2 O (denoted as alum), animal glue or gelatin (denoted as glue), and water contents on rates of paper degradation [ k Δ(1/DP)] and color changes (k ΔL and k Δb). The results show that the unsized extra-pure Xuan paper sample has good stability due to appreciable alkaline reserve, weakly alkalinity, and no presence of transition metals. Fourier transform infrared (FTIR) spectra and scanning electron microscope (SEM) images demonstrate the presence of sizing. Given that the alum-glue solution has been widely used in paper conservation, the results in this study demonstrate the devastating role of KAl(SO 4) 2 ·12H 2 O and the protective effects of gelatin on durability of treated papers, verified by the DP-related data. Additionally, it was found that the presence of alum is mainly responsible for the lightness decrease of the treated papers, and animal glue plays a primary role in paper yellowing. The findings in this research can deepen our understanding of the rate of paper degradation and color changes for the Xuan paper treated with the alum-glue solution. [ABSTRACT FROM AUTHOR]

Thermodynamically favorable selective electrooxidation reactions coupled with hydrogen evolution reaction (HER) is a promising strategy for simultaneous production of value-added chemicals and hydrogen. In this work, a binder-free gold nanoflowers electrode based on carbon paper is prepared and used as anode catalyst, which results in good charge transfer, high stability and superior catalytic activity for electrooxidation of glycerol. We develop an integrated system of glycerol electrooxidation with HER, and the effect of potential on the distribution of anodic electrooxidation products and cathodic hydrogen production are investigated. At 1.0 V, the overall reaction reaches 10 mA cm−2 and the selectivity of glyceric acid (GLA) reaches 97.2%. At 1.2 V, hydrogen production reaches the highest value of 960 μmol L−1 and the anode product consists of a mixture of glyceric acid, glycolic acid (GA) and formic acid (FA). At 1.3 V, the selectivity of FA reaches 87.3%. Operando technique in situ infrared spectroscopy is used to monitor the immediate evolution and study the pathway of controlled glycerol electrooxidation. This work demonstrates carbon paper is a promising substrate material of binder-free electrode applied in thermodynamically favorable electrocatalytic reactions boosting hydrogen evolution. [Display omitted] • A binder-free electrode based on carbon paper is developed. • Hydrogen production is increased by 24 times with the addition of glycerol. • The selectivity of glyceric acid on carbon paper supported gold nanoflowers is 97.2%. • In situ FTIR reveals the pathway for electrooxidation of glycerol. [ABSTRACT FROM AUTHOR]

• Starch paste was destroyed more easily than the paper fibers under UV-A irradiation. • Paper coated with high concentration of paste could cause fiber breakage due to the photodegradation of paste. • Paper coated with low concentration of paste could damage both the paste and paper fibers. • It's important to keep an appropriate concentration of starch paste to improve the irradiation stability of paste-restored paper artifacts. Starch paste has been the main adhesive of choice for paper conservation until now. Studies evaluating the properties of paste-coated paper under UVA irradiation conditions are limited but necessary to enable conservators for a proper choice of materials in terms of durability. In this paper, SEM, FTIR, Raman, and measurements of mechanical properties were used to investigate the aging features of UVA-irradiated paste-coated paper. The increased macro and micro physical and chemical changes with increasing UVA exposure time indicated the degradation of paste and paper polymers. The pH and spectroscopic analyses indicated that the carboxyl groups, which led to the acidity of the sample, were slowly produced with increasing irradiation, and the pH of the paste was lower than that of the paper samples when exposed for the same amount of time. The change in crystallinity also affected the degradation rate of paste-coated papers. SEM observations showed that the paste was destroyed more easily than the paper fibers, a higher concentration of paste caused the paper fibers to break, and a lower concentration of paste damaged both the paste and paper fibers. The present study suggests that an appropriate concentration of paste coated on the paper surface could improve the irradiation stability of paper samples for paste-restored paper artifacts. [ABSTRACT FROM AUTHOR]

• BC/ZnO nanocomposite strengthens paper and improves aging resistance. • The nanocomposite imparts antifungal properties to paper. • The nanocomposite helps in deacidification of paper. Paper, commonly used as an information carrier, can become acidified and brittle over time. In this study, 0.3 % bacterial cellulose (BC) composite with 1.0% zinc oxide (ZnO) nanoparticles was prepared and used to coat brittle book paper for deacidification and consolidation. The BC/ZnO nanocomposite was characterized using zeta potential, micro morphology, elemental mapping, X-ray photoelectron spectra, Fourier transform infrared, and thermogravimetric analyses. The results indicated that the composite exhibited good stability. ZnO nanoparticles were bonded to the hydroxyl groups on BC, enhancing the thermal stability of BC. The composite was uniformly sprayed on the paper surface, and the mechanical properties, color difference, readability, pH, and micromorphology of the paper samples were examined before and after the treatment. The BC/ZnO nanocomposite exhibited good deacidification and consolidation effects on paper samples with low impact on the original paper appearance. Moreover, the BC/ZnO nanocomposite showed a good inhibitory effect on fungi growth on paper. [ABSTRACT FROM AUTHOR]

• Adding kaolin reduces the volatility and leachability of heavy metals. • Xerogel with high porosity was successfully synthesized for heavy metal adsorption. • Silica-alumina xerogel can effectively adsorb heavy metals in pyrolysis gas. • Heavy metal species can form ionic or covalent bonds with kaolinite. It is of great significance to reduce the secondary risk of heavy metals during the pyrolysis of paper sludge. This study used kaolin and alumina-silica-based xerogels to control heavy metals released during sludge pyrolysis. Pyrolyzing a mixture of sludge and 7% kaolin at 400 °C achieved high retention rates for Cu (95.85%), Zn (95.97%), Pb (97.15%), Cd (84.23%), and Cr (84.05%) when the pyrolysis tail gas was treated with 9 g of xerogel. The addition of kaolin facilitated the transformation of Cu, Zn, Pb, and Cr from the unstable fraction to the stable fraction in pyrolysis biochar, reducing their leachability. The xerogels also played a crucial role in adsorbing and stabilizing the heavy metals. The results of thermodynamic equilibrium calculations showed that Pb(g), PbS(g), PbCl 2 (g), PbCl(g), Zn(g), ZnCl 2 (g), and Cd(g) were the main gaseous products of Zn, Pb, and Cd during paper sludge pyrolysis. The Pb atoms in PbCl 2 and PbS, and the Zn atoms in ZnCl 2 bond with the oxygen atoms on the kaolin surface by covalent bonds, while the Cl atoms in PbCl and the Pb atoms of elemental lead form ionic bonds with H and O atoms on the kaolinite surface, respectively. These experimental and simulation results offer new ideas for controlling heavy metals during sludge pyrolysis. [ABSTRACT FROM AUTHOR]

• Use of Ag-functionalized nanocrystalline cellulose on two paper types is studied. • Spectral reflectance is measured and CIE L*a*b* coordinates under D65 are obtained. • The treatment induces a pinkish coloration mainly evident in the inoculation region. • Reactions to the treatments of the two types of paper are different. • The proposed method can be applied to analyze effects of any type of treatment. Artifacts made of paper (books, manuscripts, and other documents) represent a valuable part of cultural heritage. They are particularly fragile compared to other objects due to the multiple physical, chemical, and biological factors able to degrade the paper basic constituents, i.e., cellulose, hemicellulose, and lignin. Moreover, hemicellulose and lignin represent an ideal growth substrate for proliferation of microorganisms and fungi. Regarding this latter aspect, researchers have experimented several methods to prevent and control fungal development on paper documents, but, sometimes, these treatments present themselves collateral effects, being responsible for the variation of paper chromatic appearance. Recently, a suspension made of crystalline nanocellulose with the adding of silver nanoparticles was tested as antifungal method. Actually, the crystalline nanocellulose has been already experimented as starting material for preservation and consolidation treatments on paper, but the adding of silver nanoparticles also provided the suspension with a broad-spectrum antimicrobial action. The aim of the research is to investigate the potential effects of the so-prepared suspension in modifying the optical characteristics of the treated paper. To do that, two different types of paper were analyzed: Whatman and Amalfi. Squared paper samples (3 cm side) were prepared, subjected to artificial ageing, and then inoculated with nanocrystalline cellulose (CNC) and with Ag-functionalized nanocrystalline cellulose (CNC/Ag). Spectral reflectance measurements were performed on the samples, and the CIE L*a*b* chromatic coordinates under D65 were obtained. Comparing the measurements referred to samples treated with CNC and those treated with CNC/Ag, it has been possible to describe the effects due to the presence of silver in the suspension. Obtained results demonstrate that the chromatic variations of the samples treated with CNC/Ag are higher than those referred to the samples treated with CNC. Specifically, the chromatic variations ΔE* D65 range from 0.2 to 10.5 for the Whatman paper and from 0.3 to 5.1 for the Amalfi one. Moreover, it has been shown that the two types of paper react in a different way to the treatments and that the alterations are not homogenous on the entire paper sample, but more evident in the inoculation region in which pinkish spots arise. Finally, it has been proved that the alterations are not stable over time, but, especially for Whatman paper, they become more evident after one month and half from the preparation of the samples. [ABSTRACT FROM AUTHOR]

As a result of its excellent analytical performance and high economic efficiency, the lateral flow immunoassay (LFIA) has proved to be a robust bioanalytical method. To achieve the application of LFIA in health care, several issues still need to be addressed, including a dramatic increase in sensitivity and reliability which is vital to enable early disease diagnosis and to avoid false-negative results. Electrokinetics in paper-based biosensors allows an integrated solution that simultaneously enables separation, preconcentration, and detection of different target analytes. Miniaturized electrokinetic biosensing platforms that incorporate all necessary electronics and use portable batteries for power sources enable their practical use at the point of care (PoC). The potential of electrokinetic phenomena in biosensing is still in its infancy, and there is still work to be done to boost the analytical sensitivity. In order to decentralize health care, the development of point-of-care (PoC) assays has gained significant attention in recent decades. The lateral flow immunoassay (LFIA) has emerged as a promising bioanalytical method due to its low cost and single-step detection process. However, its limited sensitivity and inability to detect disease biomarkers at clinically relevant levels have hindered its application for early diagnosis. This review explores the potential of merging different electrokinetic phenomena into paper-based assays to enhance their analytical performance, offering a versatile and affordable approach for PoC testing. The review exposes the challenges faced in integrating electrokinetic phenomena with paper-based biosensing and concludes by discussing the issues that need to be improved to maximize the potential of this technology for early diagnosis. [ABSTRACT FROM AUTHOR]

Paper with simultaneous fire-resistance and hydrophobicity have greatly potential applications in the fields of packing, storage and delivering information, which attracts increasing attention recently. Different from the traditional cellulose-based paper which is extremely easily damaged by water and fire, a new type of highly flexible, fire-resistant and hydrophobic paper based on Si 3 N 4 nanowires and polydimethylsiloxane (PDMS) is reported. Specially, the Si 3 N 4 @PDMS core-shell nanowires with 3D interlocking structure are designed, in which the Si 3 N 4 nanowires act as the inorganic fire-resistant frameworks and the PDMS shell with low surface energy provides the hydrophobic surface. The Si 3 N 4 @PDMS core-shell nanowires are intertwined and interlaced to form a highly flexible Si 3 N 4 @PDMS paper. The tensile strength of Si 3 N 4 @PDMS paper is 6.19 MPa, indicating the good mechanical property. The obtained Si 3 N 4 @PDMS paper has the characteristics of writability, fire-resistance and hydrophobicity. The high thermal stability of Si 3 N 4 nanowires makes Si 3 N 4 @PDMS paper exhibit excellent fire resistance. No obvious change is observed for the commercial paper with Si 3 N 4 @PDMS paper as the fire-shielding layer after heating for 30 min. In addition, the contact angles of water droplets are all greater than 110° over the surfaces of Si 3 N 4 @PDMS paper after mechanical damages, chemical corrosions and thermal treatments. Si 3 N 4 @PDMS paper can be used in oil/water separation and oil collection. More importantly, Si 3 N 4 @PDMS paper can be used for writing without being damaged by fire or water. The present work may inspire the development and application of functional paper and is expected to become a breakthrough in the traditional paper industry. [ABSTRACT FROM AUTHOR]

Fontan-type surgery is the final step in the sequential palliative surgical treatment of infants born with a univentricular heart. The resulting long-term haemodynamic changes promote liver damage, leading to Fontan-associated liver disease (FALD), in virtually all patients with Fontan circulation. Owing to the lack of a uniform definition of FALD and the competitive risk of other complications developed by Fontan patients, the impact of FALD on the prognosis of these patients is currently debatable. However, based on the increasing number of adult Fontan patients and recent research interest, the European Association for The Study of the Liver and the European Reference Network on Rare Liver Diseases thought a position paper timely. The aims of the current paper are: (1) to provide a clear definition and description of FALD, including clinical, analytical, radiological, haemodynamic, and histological features; (2) to facilitate guidance for staging the liver disease; and (3) to provide evidence- and experience-based recommendations for the management of different clinical scenarios. [ABSTRACT FROM AUTHOR]

Through the pyrolysis of cellulose-based paper templates infiltrated with a suitable polymer precursor, ceramic composites exhibiting a paper-like structure can be conveniently prepared. Such polymer-derived ceramic papers (PDCPs) unite the unique morphology of regular cellulose papers with the properties of the ceramic system utilized. Here, two paper templates, made from eucalyptus and cotton, respectively, were infiltrated with two polysilazane-based polymer precursors modified with either Fe, Ni, or Pd and converted into multi-phasic ceramic papers. In addition to the type of paper template, precursor composition, and transition metal used, the present study aims to rationalize the influence of pyrolysis temperature and atmosphere on the morphology, microstructure, and phase composition of the ceramic papers generated. For this purpose, scanning electron microscopy, SEM, and (scanning) transmission electron microscopy, (S)TEM, in conjunction with EDS analyses were used to elucidate the microstructural features of the ceramic composites in great detail. It is shown that the transition metals precipitate as nanosized metallic particles and silicides in the case of Pd and Ni, while the introduction of Fe features oxide and carbide phases in addition to that. Moreover, the metals catalyze both the graphitization of the cellulose fibers and, at higher temperatures, the generation of whisker-like Si-based nanostructures composed of either SiC or Si 3 N 4 , depending on the processing atmosphere used. [ABSTRACT FROM AUTHOR]

Rewritable paper is of great significance for environmental and sustainable development. Specially, the water rewritable paper based on hydrochromism has aroused extensive research interesting for being clean, convenient and compatible with the current ink jet printer. Nevertheless, previously reported water rewritable paper requires complex and time-consuming fabricating process. Here, we report a facile strategy to fabricate structural colored water rewritable paper simply via two step infiltration on commercially available paper. After infiltration of graphene laminates and SiO 2 colloidal spheres in sequence, the obtained paper is integrated with assembled graphene laminates (AGLs)/amorphous colloidal arrays (ACAs) hierarchical composite structure. Owing to the advantageous micro-topography, selective separation capacity and high visible light absorption property of the underlying AGLs, SiO 2 ACAs with vivid structure color can be realized. Moreover, the hydrochomism of the hierarchical composite structure is resulted from the synergistic contribution of the hydrophilic structural color and the visible light absorption property of AGLs. Our strategy is based on the environmental-friendly structural color and convenient to realized, which offers a promising alternative to rapidly fabricate colored water rewritable paper. [Display omitted] [ABSTRACT FROM AUTHOR]

[Display omitted] • Semi-automated generation of regionalized paper recycling life-cycle inventories. • National impacts on climate change of recycling three paper grades in 191 countries. • Life-cycle assessment case study of Quebec's mixed wastepaper recycling system. Recycling is a commonly acknowledged strategy to reduce the environmental impacts linked to primary resource exploitation. Large regional variations can be observed in recycling processes' parameters, like efficiency, energy mix and treatment of rejects. Life-cycle assessment (LCA) is widely used to evaluate the environmental impacts of recycling processes, but existing studies are neither harmonized nor sufficient to provide a comprehensive geographical and technological coverage of recycling processes. The purpose of this research is to develop an efficient and iterative approach for the parametrized generation of semi-automated regionalized life-cycle inventories that take into account technological and geographical variabilities in the recycling sector. The regionalization framework is then applied to create a parametrized paper recycling regionalization tool. This tool is used in the results section to compare the national climate change impacts of recycling three paper grades. Results show a significant global warming impact variability between countries for recycled graphic paper (0.36 to 2.25 kg CO 2 -Eq/kg wastepaper recycled), newsprint (0.27 to 1.84 kg CO 2 -Eq/kg wastepaper recycled) and corrugated cardboard (0.28 to 1.68 kg CO 2 -Eq/kg wastepaper recycled) productions. A regionalized LCA of the international recycling of the mixed wastepaper exported from Quebec's (Canada) sorting centers is also performed with the tool and compared to the non-regionalized mixed wastepaper recycling process available in the ecoinvent database. Only nine midpoint ReCiPe impact categories remain environmentally advantageous compared to virgin paper production when applying the regionalization methodology, compared to sixteen when using the ecoinvent process, illustrating how regionalization can substantially influence LCA results. [ABSTRACT FROM AUTHOR]

A thermal method of synthesis and fixation of Pt nanoparticles (Pt NPs) on carbon paper is proposed in this paper. Carbon paper was coated with H 2 PtCl 6 by simple immersion in an ethanol solution containing the Pt precursor. Thereafter, H 2 PtCl 6 was decomposed in inert atmosphere into Pt NPs by applying a temperature of 600 °C. Formed Pt NPs were able to oxidize the surrounding carbon fiber surface. This local thermal oxidation of carbon promoted the generation of nano-roughness and Pt NPs were embedded in the carbon fiber, thus favoring their fixation on carbon paper. Pt load can be easily controlled by the number of coating processes applied. The proposed method combines the advantage of achieving small size nanoparticles (5–10 nm) with enhanced fixation of Pt NPs when compared with electrochemical synthesis. The optimal number of coatings applied was three, which produced a complete coverage of carbon paper surface (with a Pt load of 0.18 mg cm−2). • Thermal method of synthesis of PtNPs on carbon paper. • Formed PtNPs locally oxidize carbon paper support. • Pt nanoparticles are embedded in carbon paper fibers. • Size of Pt nanoparticles obtained is around 5–10 nm. • Thermal synthesis of PtNPs produce more electroactive NPs than electrochemical one. [ABSTRACT FROM AUTHOR]

[Display omitted] • PCB was co-pyrolyzed in fixed and fluidized bed (FB) pyrolyzers with Ca-based additives. • Catalytic and dehalogenation capacities of CaO, Ca(OH)2, and CaO + Ca(OH)2 were compared. • CaO reduced the halogen content of bio-oil up to 80 and 92% in fixed bed and FB. • Halide fixation in the solid phase by additives was more effective in FB than fixed bed. • Up to 40.6% liquid recovery was achieved in a FB containing CaO + Ca(OH) 2. This study compares the impact of the calcium-based additives and the pyrolyzer on the recovery and the halide content of the oil produced from the pyrolysis of paper-laminated phenolic resin printed circuit boards (FR2-PCB). The preliminary experiments showed that the maximum liquid recovery (40.6%) was achieved in a fluidized bed pyrolyzer containing a 50:50 mixture of CaO and Ca(OH) 2 operating at T = 620 °C and PCB-to-additive ratio (FR2/A) = 5.4 g/g for 22 min. Extra tests were then carried out under these conditions in fixed and fluidized bed pyrolyzers to separately explore the impact of CaO, Ca(OH) 2 , and CaO + Ca(OH) 2 on the liquid recovery (L R) and the halogen content of the non-solid products. In the fluidized bed, L R in the presence of CaO, Ca(OH) 2 , and CaO + Ca(OH) 2 was 34.5%, 41.2%, and 38.9 wt%, respectively. The fraction of phenolic compounds in the pyrolysis oil ranged from 86% to 93%, about 1–3% higher than the corresponding values in the fixed bed. Using additives led to lower halide content in the pyrolysis oil of the fluidized bed than that of the fixed bed. However, the opposite trend was observed in the absence of additives. Regardless of the type of pyrolyzer, Ca(OH) 2 was more successful than CaO in increasing L R , whereas CaO was more effective than Ca(OH) 2 in pyrolysis oil dechlorination. Co-pyrolysis of FR2-PCB and CaO + Ca(OH) 2 in a fluidized bed reactor was identified as a practical approach to enhance the recovery of pyrolysis oil comprising only 5% of the original halogen content of the feedstock. [ABSTRACT FROM AUTHOR]

• Nutrition care should be individualized using clinical data and goals of PwCF. • Consider potential CV complications associated with the legacy, high fat/high calorie CF diet. • FI is a concern in PwCF from all socioeconomic sectors and screening should be part of standard. • There is a lack of data to make specific suggestions about salt intake in those PwCF and hypertension. • Inline enzyme cartridges are effective for digesting nutrients and promoting weight gain in PwCF. To provide interim advice and considerations to the CF Community around CF nutrition in the current era. The Cystic Fibrosis (CF) Foundation organized a multidisciplinary committee to develop a Nutrition Position Paper based on the rapidly changing nutrition landscape in CF, due in part to widespread use of cystic fibrosis transmembrane regulator highly effective modulator therapy (HEMT). Four workgroups were formed: Weight Management, Eating Behavior/Food Insecurity, Salt Homeostasis and Pancreatic Enzyme use. Each workgroup conducted their own focused review of the literature. The committee summarized current understanding of issues pertaining to the four workgroup topics and provided 6 key take-aways around CF Nutrition in the new era. People with CF (pwCF) are living longer, particularly with the advent of HEMT. The traditional high fat, high calorie CF diet may have negative nutritional and cardiovascular consequences as pwCF age. Individuals with CF may have poor diet quality, food insecurity, distorted body image, and an higher incidence of eating disorders. An increase in overweight and obesity may lead to new considerations for nutritional management, given potential effects of overnutrition on pulmonary and cardiometabolic parameters. [ABSTRACT FROM AUTHOR]

This quality improvement project aimed to transition completion of Edmonton Symptom Assessment System (ESAS) at our supportive care clinic from paper to electronic format. Proportion of patients who completed electronic ESAS (eESAS). Starting July 2018, patients could complete eESAS 24h before check-in (eESAS-before), eESAS after check-in (eESAS-after) or on paper (pESAS). A total of 6631 cancer patients had 25,767 clinic visits between July 13, 2018 and November 5, 2021. The ESAS completion rate was 100%. eESAS uptake gradually increased over time, first reaching ≥75% eESAS completion in 5/2019 (eESAS-after 61.9%; eESAS-before 14.0%; pESAS 24.1%). We observed a sharp uptake in eESAS-before since adoption of telehealth during the pandemic (May 2020) and the ≥75% eESAS target was consistently achieved from November 2020 onwards (eESAS-after 0.6%; eESAS-before 76.7%; pESAS 22.7%). In an anonymous survey, we identified several modifiable barriers to implementing eESAS. Transition to eESAS was a gradual process and was catalyzed by the pandemic. [ABSTRACT FROM AUTHOR]

• Preparation of ZIF-67/PEDOT/CP self-supporting electrodes using simple in situ hydrothermal. • The addition of PEDOT to ZIF-67 helps to achieve high electrical conductivity and large specific surface area. • The sensor has a high detection performance for CGA. • ZIF-67/PEDOT/CP provided a new sensor for the detection of CGA in real sample. The design of efficient electrocatalysts for the determination of chlorogenic acids (CGA) is crucial in the biological and medical fields. In this paper, ZIF-67/poly(3,4-ethylenedioxythiophene) (PEDOT) nanocomposites were synthesised. The introduction of PEDOT increased the electrical conductivity of the ZIF-67/PEDOT composites, inhibited the Co atom agglomeration, led to the exposure of more active sites and increased the transport channels. An ultrasensitive CGA sensor based on ZIF-67/PEDOT nanocomposite modified carbon paper (CP) electrode was developed. The nanomaterials were characterised using scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray diffraction spectroscopy (XRD). Cyclic voltammetry (CV) and differential pulse voltammetry (DPV) were used to study the electrochemical properties of the modified CP electrode. In addition, the effects of different experimental conditions such as pH, scan rate and concentration on the peak current of CGA were investigated. Under the optimised conditions, the linear range of ZIF-67/PEDOT/CP for the determination of CGA was 0.1 ∼ 40 μM, and the limit of detection (LOD) was as low as 0.003 μM (S/N = 3). Furthermore, the sensor was successfully used for the quantitative analysis of CGA in real samples. [ABSTRACT FROM AUTHOR]

[Display omitted] • Designing materials using rice-leaf-mimetic paper as a substrate. • Engineering rice-leaf-mimetic paper with hydrochromic dyes or biolubricants. • Processes based on mass-producible papermaking unit operations. Biomimetics has revolutionized materials innovation by drawing inspiration from biological systems. Cellulosic paper, a sustainable biomaterial, offers immense potential for biomimetic research. Paper-based biomimetic materials, which replicate the structures and functionalities of natural materials by utilizing the cellulosic fiber network as a substrate or skeleton, provide customizable functional properties, thereby enabling advanced applications. Here, we introduce rice-leaf-mimetic paper, inspired by the leaf's microstructure and biowax-based cuticle. This paper exhibits self-cleaning superhydrophobicity and showcases possibilities for additional functionalities, including antibacterial properties and food preservation, as evidenced in our prior research. We propose its utilization as a substrate for rewritable and biolubricant-infused surfaces. These somehow distinct surfaces draw inspiration from the chemistry and microstructure of the rice leaf. Although incorporating hydrochromic dyes enables rewritability, controlling the retention time of colors remains challenging. The biowaxy structure of the paper prolongs color maintenance by inhibiting water evaporation. Moreover, the hierarchically rough microstructure of rice-leaf-mimetic paper effectively stores biolubricant molecules, reducing friction and enhancing slipperiness. Surface microcavity ratio analysis provides insights into the paper's biolubricant-storability. The surface engineering of rice-leaf-mimetic paper using hydrochromic dyes or biolubricants holds potential for designing novel materials. Unveiling the vast potential of easily scalable papermaking processes alongside biomimetics and surface engineering opens new avenues for materials innovation. [ABSTRACT FROM AUTHOR]

• Liquid water saturation in carbon paper is measured • Quantifies the capillary trapping effect of isolated water drops in carbon papers • Proposes a model describing liquid water drops transport In previous macroscopic average models of proton exchange membrane fuel cells (PEMFCs), liquid water was assumed to be continuous throughout the carbon paper. The transport of disconnected water drops in carbon paper has long been neglected in these models, which tend to underestimate water saturation in carbon paper. This study proposes a two-phase flow model that considers the transport of disconnected water drops to simulate the air-water transport in carbon paper. The proposed model was established based on the relationship between capillary force and liquid water saturation, and this relationship was obtained by conducting centrifuge experiments. In the centrifuge experiment, initially, the water saturation inside the carbon paper sample was one, and the centrifugal acceleration was zero. As the centrifugal acceleration increased, the water saturation decreased owing to the centrifugal force. After twenty seconds, the water saturation no longer decreases because the centrifugal force on the liquid water is balanced by the capillary force. Centrifugal acceleration was used to evaluate the capillary force. When the centrifugal acceleration was 185 m s − 2 , the saturation of the water drops in the balanced state was 32.0%. As the centrifugal acceleration increases to 739 m s − 2 , the saturation decreases to 6.5%. According to the experimental results, a function correlating the saturation and centrifugal acceleration, that is, the capillary force, was established. Finally, the results show that the centrifugal acceleration is more than 18.5 times that of the gravitational acceleration, indicating that the effect of gravity on the motion of water drops is negligible. [Display omitted] [ABSTRACT FROM AUTHOR]