Search

Unlike the conventional one-dimensional (1D) core–shell nanowires (NWs) composed of p-type shells and n-type cores, in this work, an inverse design is proposed by depositing n-type ZnO (shell) layers on the surface of p-type CuO (core) NWs, to have a comprehensive understanding of their conductometric gas-sensing kinetics. The surface morphologies of bare and core–shell NWs were investigated by field emission scanning electron microscope (FE-SEM). The ZnO shell layer was presented by overlay images taken by electron dispersive X-ray spectroscopy (EDX) and high-resolution transmission electron microscopy (HRTEM). The pronounced crystalline plane peaks of ZnO were recorded in the compared glancing incident X-ray diffraction (GI-XRD) spectra of CuO and CuO–ZnO core–shell NWs. The ZnO shell layers broaden the absorption curve of CuO NWs in the UV-vis absorption spectra. As a result of the heterostructure formation, the intrinsic p-type sensing behavior of CuO NWs towards 250 and 500 ppm of hydrogen (H2) switched to n-type due to the deposition of ZnO shell layers, at 400 °C in dry airflow.

Green nanotechnology is a rapidly growing field linked to using the principles of green chemistry to design novel nanomaterials with great potential in environmental and health protection. In this work, metal and semiconducting particles (AuNPs, AgClNPs, ZnO, AuZnO, AgClZnO, and AuAgClZnO) were phytosynthesized through a “green” bottom-up approach, using burdock (Arctium lappa L.) aqueous extract. The morphological (SEM/TEM), structural (XRD, SAED), compositional (EDS), optical (UV–Vis absorption and FTIR spectroscopy), photocatalytic, and bio-properties of the prepared composites were analyzed. The particle size was determined by SEM/TEM and by DLS measurements. The phytoparticles presented high and moderate physical stability, evaluated by zeta potential measurements. The investigation of photocatalytic activity of these composites, using Rhodamine B solutions’ degradation under solar light irradiation in the presence of prepared powders, showed different degradation efficiencies. Bioevaluation of the obtained composites revealed the antioxidant and antibacterial properties. The tricomponent system AuAgClZnO showed the best antioxidant activity for capturing ROS and ABTS•+ radicals, and the best biocidal action against Escherichia coli, Staphylococcus aureus and Pseudomonas aeruginosa. The “green” developed composites can be considered potential adjuvants in biomedical (antioxidant or biocidal agents) or environmental (as antimicrobial agents and catalysts for degradation of water pollutants) applications.

Orthorhombic HfO2 exhibits nanoscale ferroelectricity that opens the perspective of ultra-scalable CMOS integration of ferroelectric memories. However, many aspects of the metastable orthorhombic crystallization mechanisms still need to be elucidated and new fabrication methods are of high interest. In this paper, the atomically resolved crystal structure of HfO2 is a 3-layer structure with a Ge-rich HfO2 intermediate layer capped by a top (cap) HfO2 layer and cladded by a bottom HfO2 layer. There is a continuity of crystal growth from the top and bottom HfO2 layers into the intermediate layer. A spatial transition from a monoclinic phase to an orthorhombic phase was revealed within a region of a few atomic layers at the interface between capped and intermediate HfO2 layers. This result suggests the mechanism of orthorhombic and monoclinic phase formation by a martensitic-like transformation of the initially grown tetragonal phase. The sample fabrication method we used involved magnetron sputtering deposition of the 3-layer structures, i.e. a stack of top HfO2/Ge-rich HfO2 intermediate/bottom HfO2 layers, followed by rapid thermal annealing. It results in self-optimized orthorhombic crystallization of HfO2 by Ge nanoparticle segregation in the intermediate layer. The ferroelectric effects are revealed by polarization–voltage hysteresis loops and piezoresponse force microscopy measurements. The atomistic computations performed by using the density functional theory support the experimental results by showing that the Ge doping of HfO2 leads to orthorhombic phase stabilization and increased Berry phase polarization.

Continuous development of Si photonics requires ecological and cost-effective materials. In this work, SiGe nanocrystals (NCs) embedded in TiO2 are investigated as a photosensitive material for vis...

The role of Ag addition on the structural, dielectric, and mechanical harvesting response of 20%(xAg − (1 − x)BaTiO3) − 80%PVDF (x = 0, 2, 5, 7 and 27 vol.%) flexible composites is investigated. The inorganic fillers were realized by precipitating fine (~3 nm) silver nanoparticles onto BaTiO3 nanoparticles (~60 nm average size). The hybrid admixtures with a total filling factor of 20 vol.% were embedded into the PVDF matrix. The presence of filler enhances the amount of β-PVDF polar phase and the BaTiO3 filler induces an increase of the permittivity from 11 to 18 (1 kHz) in the flexible composites. The addition of increasing amounts of Ag is further beneficial for permittivity increase; with the maximum amount (x = 27 vol.%), permittivity is three times larger than in pure PVDF (εr ~ 33 at 1 kHz) with a similar level of tangent losses. This result is due to the local field enhancement in the regions close to the filler-PVDF interfaces which are additionally intensified by the presence of silver nanoparticles. The metallic addition is also beneficial for the mechanical harvesting ability of such composites: the amplitude of the maximum piezoelectric-triboelectric combined output collected in open circuit conditions increases from 0.2 V/cm2 (PVDF) to 30 V/cm2 for x = 27 vol.% Ag in a capacitive configuration. The role of ferroelectric and metallic nanoparticles on the increasing mechanical-electric conversion response is also been explained.

The present study aimed to assess the feasibility of developing low-cost multipurpose iron oxide/TiO

The high-k-based MOS-like capacitors are a promising approach for the domain of non-volatile memory devices, which currently is limited by SiO2 technology and cannot face the rapid downsizing of the electronic device trend. In this paper, we prepare MOS-like trilayer memory structures based on high-k ZrO2 by magnetron sputtering, with a 5% and a 10% concentrations of Zr in the Zr–ZrO2 floating gate layer. For crystallization of the memory structure, rapid thermal annealing at different temperatures between 500 °C and 700 °C was performed. Additionally, Al electrodes were deposited in a top-down configuration. High-resolution transmission electron microscopy reveals that ZrO2 has a polycrystalline–columnar crystallization and a tetragonal crystalline structure, which was confirmed by X-ray diffraction measurements. It is shown that the tetragonal phase is stabilized during the crystallization by the fast diffusion of oxygen atoms. The capacitance–voltage characteristics show that the widest memory window (ΔV = 2.23 V) was obtained for samples with 10% Zr annealed at 700 °C for 4 min. The charge retention characteristics show a capacitance decrease of 36% after 10 years.

Due to its physical and chemical properties, the n-type tungsten oxide (WO3) semiconductor is a suitable photoanode for water decomposition reaction. The responses of the photoelectrochemical PEC water-splitting properties as an effect of structural and optical changes of WO3 thin films, as well as the nature of electrolyte solutions, were studied in this work. The WO3 thins films have been obtained by pulsed laser deposition (PLD) on silicon (Si(001)) covered with platinum substrates using three different laser wavelengths. As the XRD (X-ray diffraction) and XTEM (cross-section transmission electron microscopy) analysis shows, the formation of highly crystalline monocline WO3 phase is formed for the film deposited at 1064 nm wavelength and poor crystalline phases with a large ordering anisotropy, characteristic of 2D structures for the films deposited at 355 nm and 193 nm wavelengths, respectively. The photogenerated current densities Jph depend on the laser wavelength, in both alkaline and acidic electrolyte. The maximum values of the photocurrent density have been obtained for the sample prepared with laser emitting at 355 nm. This behavior can be correlated with the coherent crystallized atomic ordering that appear for long distances (10&ndash, 15 nm) in the (001) plane of the monoclinic WO3 phase structure films obtained at 355 nm laser wavelength. All the samples show poor current density in dark conditions and they are very stable in both acidic and alkaline solutions. The highest photocurrent density value is obtained in acidic solution for the WO3 thin film prepared by 355 nm laser (29 mA/cm2 at 1.6 V vs. RHE (1.35 V vs. Ag/AgCl)).

In the field of research for designing and preparing innovative nanostructured systems, these systems are able to reveal the presence of heavy metals in water samples, and can efficiently and selectively interact with them, allowing for future applications in the field of water remediation. We investigated the electronic and molecular structure, as well as the morphology, of silver nanoparticles stabilized by mixed biocompatible ligands (the amino acid L-cysteine and the organic molecule citrate) in the presence of cadmium and arsenic ions. The molecular, electronic, and local structure at the ligands/silver nanoparticles interface was probed by the complementary synchrotron radiation-induced techniques (SR-XPS, NEXAFS and XAS). The optical absorption (in the UV-Vis range) of the nanosystem was investigated in the presence of Cd(II) and As(III) and the observed behavior suggested a selective interaction with cadmium. In addition, the toxicological profile of the innovative nanosystem was assessed in vitro using a human epithelial cell line HEK293T. We analyzed the viability of the cells treated with silver nanoparticles, as well as the activation of antioxidant response.

Plasmonic nanostructures based on AuAg nanoalloys were fabricated by thermal annealing of metallic films in an argon atmosphere. The nanoalloys were chosen because they can extend the wavelength range in which plasmon resonance occurs and thus allow the design of plasmonic platforms with the desired parameters. The influence of initial fabrication parameters and experimental conditions on the formation of nanostructures was investigated. For the surface morphology studies, chemical composition analysis and nanograin structure, Scanning Electron Microscopy (SEM), X-Ray Photoelectron Spectroscopy (XPS), Energy Dispersive X-Ray Spectroscopy (EDS) and High-Resolution Transmission Electron Microscopy (HR TEM) measurements were performed. The position of the resonance band was successfully tuned in the 100 nm range. The EDS together with the XPS analysis confirmed the formation of an alloy with the aspect ratio of individual metals in a single nanoisland similar to the ratio of the thicknesses of the initially sputtered layers. The experimental research was complemented by the neural network model, which enables the calculation of the absorbance peak depending on the thickness of Au and Ag layers and the annealing time. The proposed model of machine learning makes it possible to fine-tune the desired position of the plasmon resonance.

Metal−organic frameworks (MOFs) are a class of porous coordination networks extraordinarily varied in physicochemical characteristics such as porosity, morphologies, and compositions. These peculiarities make MOFs widely exploited in a large array of applications, such as catalysis, chemicals and gas sensing, drug delivery, energy storage, and energy conversion. MOFs can also serve as nanostructured precursors of metal oxides with peculiar characteristics and controlled shapes. In this work, starting from MIL125-(Ti), a 1,4-benzenedicarboxylate (BDC)-based MOF with Ti as metallic center, mesoporous TiO2 powders containing both anatase and rutile crystalline phases were produced. A challenging utilization of these porous MOF-derived Ti-based oxides is the optically-based quantitative detection of molecular oxygen (O2) in gaseous and/or aqueous media. In this study, the photoluminescence (PL) intensity changes during O2 exposure of two MOF-derived mixed-phase TiO2 powders were probed by exploiting the opposite response of rutile and anatase in VIS-PL and NIR-PL wavelength intervals. This result highlights promising future possibilities for the realization of MOF-derived doubly-parametric TiO2-based optical sensors.

In this paper, we report studies on Al2O3/Ge/Al2O3 trilayer memory structures deposited by magnetron sputtering at room temperature on p-Si substrates coated with 3 nm SiO2. The changes of the structure, morphology and memory properties induced by rapid thermal annealing (RTA) in a broad temperature range 550–900 °C have been carefully investigated. High resolution transmission electron microscopy (HRTEM) revealed the existence of distinct RTA effects for different temperature ranges, in correlation with memory properties measured on Al/Al2O3/Ge/Al2O3/SiO2/p-Si/Al devices. Thus, at temperatures smaller than 650 °C, Ge diffuses into adjacent Al2O3, the layers remaining amorphous. The memory window increases from as-deposited samples to those annealed at 600 °C reaching the maximum of 5.4 V. After RTA at 700 °C, Ge nanocrystals (NCs) in intermediate Ge layer and Ge-rich amorphous nanoparticles in Al2O3 tunnel oxide are formed. Increasing RTA temperature to 800 and 900 °C, Ge NCs are no longer formed due to Ge strong diffusion. Instead, Ge-rich mixed GeAl oxide NCs of unknown crystalline structure are evidenced by HRTEM. The memory window continuously decreases with annealing temperature in the range 650–900 °C. The ON (OFF) charge loss of only 11% (9.8%) was found by extrapolation to 10 years.

A new method based on transformation of magnetron sputtered platinum thin films into platinum nanostructures enclosed by high-index facets, using electrochemical potential cycling in a twin working electrode system is reported. The controllable formation of various Pt nanostructures, described in this paper, indicates that this method can be used to control a selective growth of high purity Pt nanostructures with specific shapes (facets or edges). The method opens up new possibilities for electrochemical preparation of nanostructured Pt catalysts at high yield.

The films of SiGe nanocrystals in SiO 2 on Si substrate were obtained by co-sputtering Si, Ge, and SiO 2 followed by rapid thermal annealing. The films structure and morphology together with electrical and photoelectrical properties were studied by x-ray diffraction, transmission electron microscopy, current - voltage and spectral photocurrent measurements. The photocurrent spectra at 300, 200 and 100 K were correlated with results obtained from X-ray diffractograms and transmission electron microscopy. The photocurrent spectra show an extension in near infrared due to the enriching SiGe nanocrystals in Ge.

To avoid the deleterious effects of dopant segregation, synthesis methods that facilitate a homogenous dopant distribution in the ceria lattice were employed. Though doping ceria by wet impregnation was also credited to induce a homogeneous solid solution even in the heavy regime (concentration ≥20%, A. Corma, P. Atienzar, H. Garcia and J. Chane-Ching, Nat. Mater., 2004, 3, 394–397), no follow up investigation has been reported. Herein, we investigated ceria nanoparticles (1%Tm-CeO2 and 1%Eu-CeO2) wet-impregnated with trivalent rare-earth (Yb, 20%), bivalent (Ca, 20%) and isovalent (Zr, 30%) metals, followed by annealing in air. Homogeneity of the solid solutions of Yb-impregnated ceria was confirmed by a two-feature characterization toolbox that included X-ray diffraction, Raman spectroscopy, transmission electron microscopy, as well as up-conversion emission as a probe tool. Since the up-conversion emission of Tm was not detectable in the absence of Yb while its efficiency depends on the average distance between Yb and Tm ions, the Yb incorporation and its migration from the surface to the lattice bulk sites in wet-impregnated ceria can be “visualized” and compared with that of the Yb bulk-doped counterpart. The use of Eu luminescence as a local probe confirmed the homogeneity of solid solutions of Ca and Zr-impregnated ceria and also sustained the opposite roles of Ca and Zr as the repeller and the scavenger of oxygen vacancies, respectively. All these results suggested that heavy doping of ceria by wet impregnation with metals with +2, +3 and +4 valencies represent a facile alternative to conventional doping approaches. Therefore, the effects of the amount and the type of metal dopant on the structural properties of CeO2 could be investigated in a more systematic and probably a more reproducible manner, which would significantly increase the potential of ceria in catalysis and other applications.

The paper describes an innovative bio-design of some hybrid nanoarchitectures containing bioartificial membranes and silver nanoparticles phytogenerated by using a natural extract Caryophyllus aromaticus (cloves) that contains many bioactive compounds. Two kinds of liposomes with and without chlorophyll a (Chla) obtained through thin film hydration method were used to achieve bio-green-generated hybrids by a simple, cost effective bottom-up approach. The characteristic peaks of CE-nAg monitored by UV–Vis absorption have firstly demonstrated the biohybrids formation. The slightly blue shift and fluorescence quenching observed by fluorescence emission spectra highlighted the formation of hybrid systems by biointeraction between lipid vesicles and silver nanoparticles. The incorporation of silver nanoparticles in lipid vesicles resulted in significant changes of FT-IR spectra of liposomes, indicating a reorganization of biomimetic membranes. All the microscopic methods (SEM, AFM and TEM) confirmed the biosynthesis of “green” AgNPs together with associated biohybrids, their spherical and quasi-spherical shapes with nano-scaled size. By TEM assay it was shown that CE-nAg are surrounded by petal like cloud structures that consist of biopolymers like proteins or polysaccharides and other phytochemicals arising from clove extract. EDS spectra confirmed the formation of phyto-nanoAg and also the presence of silver in the biohybrids. In addition, Selected Area Electron Diffraction showed characteristic polycrystalline ring patterns for a cubic structure of the clove-generated AgNPs. The hybrid materials showed efficient physical stability, i.e. ξ value of −28.0 mV (for biohybrids without Chla, BH) and of −31.7 mV (for biohybrids labelled with Chla, Chla-BH), assured by strong electrostatic repulsive forces between particles. The “green” nano-silver particles (CE-nAg) showed remarkable antioxidant activity (AA = 90.2%). The biohybrids loaded with clove-AgNPs proved to be more effective, scavenging about 98.8% of free radicals (in case of Chla-BH), and of 92.6% (in case of BH). The antibacterial effectiveness showed that green AgNPs combine in a synergistic manner the antibacterial properties of clove extract with those of silver, resulting in an enhancement of inhibition diameter, by 20%. Chla-BH proved to be more potent against Escherichia coli, than BH, exhibiting an inhibition diameter of 42 mm. Regarding the in vitro cytotoxicity against tumour cells, the CE-nAg concentration significantly influenced the cell viability, i.e. IC50 was 3.6% (v/v) for HT-29 cells. Chla-BH was more effective against HT-29 cancer cells at the concentrations ranging from 0 to 18% (v/v), when the normal cells were not affected. Clove-generated AgNPs exhibited haemolytic activity against hRBCs, while the biohybrids were haemocompatible. The action mechanism on the two cell lines (mouse fibroblast L929 cells and human colorectal adenocarcinoma HT-29 cells) investigated by fluorescence microscopy demonstrated that CE-nAg killed almost all the cells (94%) through necrosis at a concentration of 33.4% (v/v). The treatment of HT-29 cells with BH resulted in: 71.5% viable cells, 19.5% apoptotic and only 9% necrotic cells, while in the case of Chla-BH treatment, only 77.5% cells were viable, 16% cells were apoptotic and 6.5% were necrotic. In this way, the developed silver-based nanoparticles can represent viable promoters to develop new biohybrids with improved features, e.g. antioxidant and antibacterial effectiveness, haemolytic activity and greater specificity towards tumour cells.

The storage and catabolism of Ultrasmall SuperParamagnetic Iron Oxide (USPIO) nanoparticles were analyzed through a multiscale approach combining Two Photon Laser Scanning Microscopy (TPLSM) and High-Resolution Transmission Electron Microscopy (HRTEM) at different times after intravenous injection in an atherosclerotic ApoE(-/-) mouse model. The atherosclerotic plaque features and the USPIO heterogeneous biodistribution were revealed down from organ's scale to subcellular level. The biotransformation of the nanoparticle iron oxide (maghemite) core into ferritin, the non-toxic form of iron storage, was demonstrated for the first time ex vivo in atherosclerotic plaques as well as in spleen, the iron storage organ. These results rely on an innovative spatial and structural investigation of USPIO's catabolism in cellular phagolysosomes. This study showed that these nanoparticles were stored as non-toxic iron compounds: maghemite oxide or ferritin, which is promising for MRI detection of atherosclerotic plaques in clinics using these USPIOs. From the Clinical Editor: Advance in nanotechnology has brought new contrast agents for clinical imaging. In this article, the authors investigated the use and biotransformation of Ultrasmall Super-paramagnetic Iron Oxide (USPIO) nanoparticles for analysis of atherosclerotic plagues in Two Photon Laser Scanning Microscopy (TPLSM) and High-Resolution Transmission Electron Microscopy (HRTEM). The biophysical data generated from this study could enable the possible use of these nanoparticles for the benefits of clinical patients.

Graphene is widely used in nanotechnologies to amplify the photocatalytic activity of TiO2, but the development of TiO2/graphene composites imposes the assessment of their risk to human and environmental health. Therefore, reduced graphene oxide was decorated with two types of TiO2 particles co-doped with 1% iron and nitrogen, one of them being obtained by a simultaneous precipitation of Ti3+ and Fe3+ ions to achieve their uniform distribution, and the other one after a sequential precipitation of these two cations for a higher concentration of iron on the surface. Physico-chemical characterization, photocatalytic efficiency evaluation, antimicrobial analysis and biocompatibility assessment were performed for these TiO2-based composites. The best photocatalytic efficiency was found for the sample with iron atoms localized at the sample surface. A very good anti-inhibitory activity was obtained for both samples against biofilms of Gram-positive and Gram-negative strains. Exposure of human skin and lung fibroblasts to photocatalysts did not significantly affect cell viability, but analysis of oxidative stress showed increased levels of carbonyl groups and advanced oxidation protein products for both cell lines after 48 h of incubation. Our findings are of major importance by providing useful knowledge for future photocatalytic self-cleaning and biomedical applications of graphene-based materials.

Lowering the temperature of crystallization by deposition of thin films on a heated substrate represents the easiest way to find new means to develop and improve new working devices based on nanocrystals embedded in thin films. The improvements are strongly related with the increasing of operation speed, substantially decreasing the energy consumption and reducing unit fabrication costs of the respective semiconductor devices. This approach avoids major problems, such as those related to diffusion or difficulties in controlling nanocrystallites size, which appear during thermal treatments at high temperatures after deposition. This article reports on a significant progress given by structuring Ge nanocrystals (Ge-NCs) embedded in silicon dioxide (SiO2) thin films by heating the substrate at 400 °C during co-deposition of Ge and SiO2 by magnetron sputtering. As a proof-of-concept, a Si/Ge-NCs:SiO2 photo-sensitive structure was fabricated thereof and characterized. The structure shows superior performance on broad operation bandwidth from visible to near-infrared, as strong rectification properties in dark, significant current rise in the inversion mode when illuminated, high responsivity, high photo-detectivity of 1014 Jones, quick response and significant conversion efficiency with peak value reaching 850% at −1 V and about 1000 nm. This simple preparation approach brings an important contribution to the effort of structuring Ge nanocrystallites in SiO2 thin films at a lower temperature for the purpose of using these materials for devices in optoelectronics, solar cells and electronics on flexible substrates.