Search

PURPOSE To compare the flexural properties and the adhesion of Lactobacillus salivarius (LS), Streptococcus mutans (SM), and Candida albicans (CA) on heat-polymerized (CV), CAD-CAM milled (CAD), or 3D-printed (3D) Poly (methylmethacrylate) (PMMA). METHODS Ultimate Flexural Strength (UFS), Flexural Strain (FS) (%) at Flexural Strength, and Flexural Modulus (FM) of specimens (65.0×10.0×3.3 mm) from each PMMA group (n=6) were calculated by using the 3-point bending test. The surface roughness profiles (R) were measured before and after polishing with a contact profilometer. LS, SM, and CA adhesion on PMMA specimens (n=18) (10 mm in diameter, 3 mm in height) was assessed after 90 minutes and 16 hours by using scanning electron microscopy. The Kruskal-Wallis test with post hoc analysis was performed to compare the groups (alpha=0.05). RESULTS Mean UFS values were 80.79±7.64 MPa for CV, 110.23±5.03 MPa for CAD, and 87.34±6.39 MPa for 3D. Mean FS values were 4.37±1.04% for CV, 4.71±0.62% for CAD, and 6.19±0.13 % for 3D. Mean FM values were 2542±301 MPa for CV, 3435±346 MPa for CAD, and 2371±197 MPa for 3D. CAD had the lowest average R value (0.29±0.16 µm) before polishing, and bacterial adhesion after 90 minutes of incubation. R value and microbial adhesion were not different amongst groups after polishing and 16 hours of incubation, respectively. CONCLUSION The CAD group displayed the best flexural properties, except for FS, the lowest roughness before polishing and bacterial adhesion after 90 minutes of incubation. All tested PMMAs had similar surface roughness after polishing, and microbial adhesion after 16 hours of incubation.

Dental calculus is the result of dental plaque mineralization, originating by tooth associated bacterial biofilm. Recent evidence revealed that the dental calculus microbiome has a more complex composition than previously considered, including an unstructured mix of both aerobes and anaerobes bacteria. Actually, we lack information about the influence of host lifestyle factors, such as diet and health on this highly biodiverse ecosystem. Here, we provide a pilot study investigating dental calculus microbial biodiversity and its relation with host diet.We collected 40 dental calculus samples during routine dental inspection; DNA was extracted and analysed through 16S amplicon sequencing, while dietary information were retrieved through a questionnaire. Associations between diet and oral bacteria taxonomy and functional pathways were statistically tested.Overall, microbiome composition was dominated by 10 phyla and 39 bacterial genera, which were differently distributed among samples. Cluster analysis revealed four main groups based on the taxonomic profile, and two groups based on functional pathways. Each taxonomic cluster was dominated by different microbial biomarkers: Streptococcus, Rothia, Tannerella, Lautropia and Fusobacterium. Bacteria genera and pathways were also associated to specific dietary element, especially vegetable and fruit intake suggesting an overall effect of diet on dental calculus microbiome.The present study demonstrate that it exists an inter-variability in the microbial composition of dental calculus among individuals of a rather homogenous population. Furthermore, the observed biodiversity and microbial functions can find an association to specific dietary habits, such as a high fiber diet or a protein rich diet. This article is protected by copyright. All rights reserved.

Oral health is fundamental to our well-being, especially in adolescence. The aim of this study is to investigate oral hygiene knowledge through a questionnaire in a sample of adolescents, paying particular attention to those wearing orthodontic braces. The study was designed as a descriptive report of a local survey. An anonymous questionnaire was distributed to individuals born between 2000 and 2005, both on paper and online. Among 213 adolescents answering the questionnaire, 206 went to the dentist at least once (most of them between 5 and 9 years old), and 144 experienced at least one session of professional oral hygiene. Approximately 83% of the sample brushed their teeth at least twice a day, while only 7% used dental floss daily. Only 54% of respondents wearing orthodontic braces were advised to undergo professional oral hygiene during their orthodontic treatment. Education on oral hygiene at home came only from their parents for 61% of the whole sample. Most respondents had their first visit to the dentist apparently too late. Flossing was rare, whether the adolescents wore orthodontic braces or not. In many cases, professional oral hygiene was not common during orthodontic treatment. Adolescents did not learn about oral hygiene from a dental specialist.

PURPOSE: To describe the possible adverse effects of sodium hypochlorite (NaOCl) solutions, high-concentration alcohol solutions, and povidone-iodine products, which are indicated for disinfection of inanimate surfaces against human coronavirus of the severe acute respiratory syndrome (SARS-CoV), on prosthesis materials, including zirconia, lithium disilicate, and acrylic resin. MATERIALS AND METHODS: A systematic literature research for articles published between January 2010 and February 2020 was conducted in Scopus, PubMed/Medline, Web of Science, Embase, and Science Direct using a combination of the following MeSH/Emtree terms and keywords: sodium hypochlorite, alcohol, ethanol, povidone-iodine, dental ceramic, zirconia, lithium disilicate, and acrylic resin. RESULTS: A total of 538 studies were identified in the search during initial screening, of which 44 were subject to full-text evaluation, and 24 fulfilled the inclusion criteria. Seven articles on zirconia and lithium disilicate investigated the effect of NaOCl (0.5% and 1%), 96% isopropanol, and 80% ethanol on bond strength after saliva contamination. The remaining articles evaluated color alteration, surface roughness modifications, decrease in flexural strength, and bonding strength of all cleaning agents on acrylic resin. CONCLUSION: NaOCl (1%) solution for 1 minute is recommended to reduce SARS-CoV infectivity and to minimize the risk of cross-contamination through prosthetic materials. The increase in surface roughness and color alteration were recorded using 1% NaOCl on acrylic resin, but this increase was not clinically significant. A decrease in bonding strength was determined after using 1% NaOCl, 96% isopropanol, and 80% ethanol solutions on lithium disilicate. Silanization before the try-in procedure and the application of the second layer of silane after cleaning methods are recommended to improve the bonding strength.

To compare the flexural properties and the adhesion of Lactobacillus salivarius (LS), Streptococcus mutans (SM), and Candida albicans (CA) on heat-polymerized (CV), CAD-CAM milled (CAD), or 3D-printed (3D) Poly (methylmethacrylate) (PMMA).Ultimate Flexural Strength (UFS), Flexural Strain (FS) (%) at Flexural Strength, and Flexural Modulus (FM) of specimens (65.0×10.0×3.3 mm) from each PMMA group (n=6) were calculated by using the 3-point bending test. The surface roughness profiles (R) were measured before and after polishing with a contact profilometer. LS, SM, and CA adhesion on PMMA specimens (n=18) (10 mm in diameter, 3 mm in height) was assessed after 90 minutes and 16 hours by using scanning electron microscopy. The Kruskal-Wallis test with post hoc analysis was performed to compare the groups (alpha=0.05).Mean UFS values were 80.79±7.64 MPa for CV, 110.23±5.03 MPa for CAD, and 87.34±6.39 MPa for 3D. Mean FS values were 4.37±1.04% for CV, 4.71±0.62% for CAD, and 6.19±0.13 % for 3D. Mean FM values were 2542±301 MPa for CV, 3435±346 MPa for CAD, and 2371±197 MPa for 3D. CAD had the lowest average R value (0.29±0.16 µm) before polishing, and bacterial adhesion after 90 minutes of incubation. R value and microbial adhesion were not different amongst groups after polishing and 16 hours of incubation, respectively.The CAD group displayed the best flexural properties, except for FS, the lowest roughness before polishing and bacterial adhesion after 90 minutes of incubation. All tested PMMAs had similar surface roughness after polishing, and microbial adhesion after 16 hours of incubation.

Purpose Compare the accuracy of intraoral digital impression in full-arch implant-supported fixed dental prosthesis acquired with eight different intraoral scanner (Ios). Methods A polymethyl methacrylate acrylic model of an edentulous mandible with six scan-abutment was used as a master model and its dimensions measured with a coordinate measuring machine. Eight different Ios were used to generate digital impression: True Definition, Trios, Cerec Omnicam, 3D progress, CS3500, CS3600, Planmeca Emelard and Dental Wings. Fifteen digital impressions were made. A software called “Scan-abut” was developed to analyse and compare the digital impression with the master model, obtaining the scanning accuracy. The three-dimensional (3D) position and distance analysis were performed. Results Mean value of the 3D position analysis showed that the True Definition (31 μm ± 8 μm) and Trios (32 μm ± 5 μm) have the best performance of the group. The Cerec Omnicam (71 μm ± 55 μm), CS3600 (61 μm ± 14 μm) have an average performance. The CS3500 (107 μm ± 28 μm) and Planmeca Emelard (101 μm ± 38 μm) present a middle-low performance, while the 3D progress (344 μm ± 121 μm) and Dental Wings (148 μm ± 64 μm) show the low performance. The 3D distance analysis showed a good linear relationship between the errors and scan-abutment distance only with the True Definition and CS3600. Conclusions Not all scanners are suitable for digital impression in full-arch implant-supported fixed dental prosthesis and the weight of the output files is independent from the accuracy of the Ios.

Background: We compare the accuracy of new intraoral scanners (IOSs) in full-arch digital implant impressions. Methods: A master model with six scan bodies was milled in poly(methyl methacrylate), measured by using a coordinate measuring machine, and scanned 15 times with four IOSs: PrimeScan, Medit i500, Vatech EZ scan, and iTero. The software was developed to identify the position points on each scan body. The 3D position and distance analysis were performed. Results: The average and ± standard deviation of the 3D position analysis was 29 μm ± 6 μm for PrimeScan, 39 μm ± 6 μm for iTero, 48 μm ± 18 μm for Mediti500, and 118 μm ± 24 μm for Vatech EZ scan (p < 0.05). Conclusions: All IOSs are able to make a digital complete implant impression in vitro according to the average misfit value reported in literature (150 μm); however, the 3D distance analysis showed that only the Primescan and iTero presented negligible systematic error sources.

STATEMENT OF PROBLEM The choice of retention type of an implant-supported fixed dental prosthesis (FDP) becomes critical when the dental implant is not placed in a prosthetically ideal location. In recent years, computer-aided design and computer-aided manufacturing (CAD-CAM) technology has enabled the correction of the location of screw access hole depending on the clinical needs of the patient. However, how FPDs with angulated screw channels (ASCs) perform clinically is unclear. PURPOSE The purpose of this prospective clinical study was to evaluate the mechanical complications and crestal bone loss (CBL) when posterior monolithic zirconia implant-supported FDPs with an ASC are used. MATERIAL AND METHODS Participants (N=37) with a missing single posterior tooth or multiple teeth, sufficient bone height, and an implant site without infection were included. Each participant received parallel-walled implants (Nobel Parallel CC) of 7-, 8.5-, or 10-mm length by using a 1-stage approach. After 4 months of healing, a conventional impression was made, and a digital workflow was followed. Monolithic zirconia restorations (Katana ML) were milled, stained, and mechanically attached to a titanium base (NobelProcera ASC abutment). CBL was measured from radiographs at 6, 12, 24, and 36 months after the placement of the prosthesis. Implant and prosthetic characteristics including implant diameter, implant length, screw channel angle (angle≤15 degrees versus angle>16 degrees), prosthetic type (single crown versus multiple-unit FDP), and antagonist dentition (natural versus prosthesis) were also recorded. A generalized linear mixed model with a log link was estimated to assess the independent predictors of CBL among the angles of ASC-retained definitive restorations and the clinically relevant variables (α=.05). RESULTS Thirty-seven participants received 51 implants, and the median follow-up period was 30 months (interquartile range: 22-36). Two single-crown implants failed within the first 12 months of delivery. The implant and restoration survival rate was 96% at 36 months. Screw loosening was recorded in 2 study participants. After a follow-up of 36 months, the mean ±standard deviation CBL value was 0.15 ±0.14 mm with an increase over time (P.05). CONCLUSIONS CBL was not associated with the angle of ASC, implant diameter, implant length, prosthetic type, or antagonist when posterior monolithic zirconia implant-supported FDPs with ASCs were used. Screw loosening in 2 situations was the only mechanical complication during the first 3 years of service.

A method is described for minimizing errors in positioning a surgical template during the insertion of implants immediately after extraction and the placement of interim prostheses with immediate loading. The technique, called sequential template immediate loading (STIL), uses modular templates to fix pins before extracting the teeth, thus giving a reliable position for the subsequent templates for inserting the implant and placing the interim prosthesis.

PURPOSE Reconstructing the occlusal morphology of posterior teeth in definitive dental prosthesis can be challenging. The use of the correlation technique enables replication of the information and occlusal anatomy of interim dental prostheses to the definitive ones. The purpose of this controlled clinical trial was to compare the static and dynamic contacts (SDC) of monolithic zirconia crowns designed with correlation and library techniques. MATERIAL AND METHODS Twenty-four patients were included in the study for a total of 28 molars. For each abutment tooth, an interim crown was fabricated and two digital scans, with and without the interim crown in place were made. Two single crowns were designed using correlation and library techniques. Fifty-six monolithic zirconia crowns were milled. The interim and definitive crowns were evaluated intraorally for SDC by using a 24-μm-thick blue articulating foil. After removing the interim and definite crowns, extraoral photographs were taken to calculate the SDC area using software (ImageJ) and analyzed by the Kruskal-Wallis test. RESULTS The average and ± standard deviation (SD) of area of the occlusal marks on interim crowns was 32.27 ± 3.45 mm2 . Definitive crowns designed by using the correlation technique had an area of 31.01 ± 3.73 mm2 ; the area in the library technique was 36.85 ± 5.78 mm2 . No statistically significant difference was found (p = 0.091) between the occlusal mark areas of the interim and definitive crowns designed by using the correlation technique. Whereas, there were significant differences between the areas of occlusal marks of the interim and definitive crowns designed by using the library technique, and between the areas of occlusal marks of definitive crowns designed by using the correlation and library techniques (p < 0.001). CONCLUSION The average area of the SDC of monolithic zirconia crowns designed by using the correlation technique was similar to that of interim crowns. The library technique was less effective when replicating the SDC compared to the correlation technique.

Statement of problem: The effect of prophylactic polishing pastes on composite resin materials has been extensively investigated, but little is known about their effect on ceramic materials. Purpose: The purpose of this in vitro study was to evaluate the effect of prophylactic polishing pastes on the 2D and 3D roughness, translucency, and gloss of different ceramic materials. Material and methods: A total of 120 flat specimens (thickness: 2 mm) obtained from computer-aided design and computer-aided manufacturing (CAD-CAM) blocks of leucite glass-ceramic (Empress CAD), lithium disilicate glass-ceramic (e.max CAD), and zirconia (Zenostar MT) were glazed and sintered. Forty specimens from each material were then divided into 4 groups and polished with Cleanic fine, Nupro fine, or Proxyt fine pastes, leaving the control group untreated. The specimens were polished for 2 minutes with a prophylaxis cup mounted on a handpiece, applying a constant load of 3.9 N at 2000 rpm. Surface roughness was measured by using a contact profilometer and a 3D optical profilometer. The translucency parameter and gloss value were calculated by using a spectrophotometer and a glossmeter. One specimen per group was observed by scanning electron microscopy at ×200 magnification. Differences in means were compared by using 2-way ANOVA followed by the Tukey honestly significant difference (HSD) test (α=.05). Results: The 2D roughness of Empress was lower than that of e.max (P.05). The gloss of Empress was higher than that of Zenostar and e.max (P

Statement of problem The marginal gap and ceramic bond strength of metal-ceramic restorations are important for success. However, studies evaluating the marginal gap and ceramic bond strength of fixed partial dentures (FPDs) produced with 3D printing technologies such as selective laser melting (SLM) are scarce. Purpose The purpose of this in vitro study was to investigate the marginal gap of cobalt-chromium (Co-Cr) alloy frameworks produced by SLM technology before and after ceramic firing. Additionally, the metal-ceramic bond strength was evaluated with the Schwickerath crack-initiation test according to the International Standards Organization (ISO) 9693-1:2012. Material and methods Conventional impressions were made, and the definitive cast of a patient requiring a 4-unit FPD was scanned. After designing the FPD, the files were sent to a service center for the fabrication of a metal master model, 80 Co-Cr frameworks, and 80 flat specimens (25×3×0.5 mm) with SLM technology. The marginal gap between frameworks and the abutment tooth of the metal master model was nondestructively measured by using an optical coordinate-measuring machine. A total of 80 sets, consisting of 1 framework and 1 flat specimen, were sent to 80 dental laboratory technicians for ceramic firing. Detailed instructions for correct manipulation of the framework and flat specimen were provided. The marginal gap was remeasured, and the 3-point bend test was used to evaluate metal-ceramic bond strength. Results Only 28 of the 80 dental technicians returned the specimens within a prespecified time and/or in adequate condition. The mean ±standard deviation marginal gap of the framework before ceramic firing was 25 ±9 μm and 34 ±12 μm after firing. The difference was statistically significant (P=.001). The mean ±standard deviation 3-point bend strength was 33 ±9 MPa. Conclusions Ceramic firing affected the marginal gap; however, all Co-Cr frameworks had a marginal gap lower than 120 μm, which is reported to be a clinically acceptable limit. Most of the specimens (80%) had a metal-ceramic bond strength value higher than the 25-MPa ISO 9693 requirement. Five of 28 dental laboratory technicians were not able to comply with ceramic firing instructions.

Background: The purpose of this review is to describe the possible effect of toothbrushing on surface roughness of resin-contained CAD/CAM materials. Methods: Systematic literature search for articles published in peer-reviewed journals between January 2000 and February 2020 has been conducted, which evaluated the effect of brushing on surface roughness of resin-contained CAD/CAM dental materials. The research was conducted in Scopus, PubMed/Medline, Web of Science, Embase, and Science Direct using a combination of the following MeSH/Emtree terms: “brushing”, “resin-based”, “dental”, “CAD/CAM”, and “surface roughness”. Results: A total of 249 articles were found in the search during initial screening. Fifty-five articles were selected for the full-text evaluation after the steps of reading of abstract/title and remotion of duplicate. Only six articles fulfilled the inclusion criteria. The Cohen’s Kappa agreement test showed an index of 0.91 for full-text. Discussion: Four of five selected articles identified an increase of surface roughness on resin-contained CAD/CAM materials after toothbrushing. Although all the articles examined used different toothpastes with no homogeneous relative dentine abrasivity (RDA) and cycles of brushing, the findings are about the same. The possible reason is attributable to the compositions of the resin-contained CAD/CAM materials. Conclusions: The surface roughness of most resin-contained CAD/CAM materials was affected by artificial toothbrushing. Correct knowledge of the composition of the dental material and toothpastes is fundamental to avoid an increase of surface roughness on prosthetic rehabilitation.

Purpose To evaluate the influence of the crown-to-implant ratio (CI) on marginal bone loss (MBL) around short dental implants placed in the posterior mandible. Materials and methods All patients treated with short implants (7 mm length) in the posterior mandible between 1994 and 2003 at the Dental Clinic of the Department of Neuroscience of the University of Padua (Italy) were retrospectively included in the analysis. MBL and clinical CI (cCI) were measured on the radiographs. Implant characteristics including implant diameter, prosthetic type, retention mode, antagonist type, veneering material, and implant surfaces were retrieved from local medical records. A generalized linear mixed model was estimated to identify the predictors of MBL. Results A total of 108 dental implants placed in 51 patients were included in the analysis. Mean follow-up was 16 years (range: 11 to 20 years). Mean cCI was 2.21 (SD = 0.31) with a mean crown height of 10.86 mm (SD = 0.99). Mean MBL was 1.42 mm (SD = 0.38). At multivariable analysis, cCI ≥ 2 was associated with higher MBL (regression coefficient: 0.27; 95% CI: 0.15 to 0.40), while implant characteristics, follow-up, and site were not associated with MBL. The effect of a cCI ≥ 2 was estimated in an increase of 0.28 mm in MBL (95% CI: 0.14 to 0.43 mm). Conclusion Higher cCI was associated with greater MBL of implant-supported fixed dental prostheses in short dental implants placed in the posterior mandible, while implant characteristics, follow-up, and site were not associated with MBL. However, the increase of 0.28 mm of MBL in patients with a cCI ≥ 2 may be not clinically relevant.

The objective of this paper is to review the current knowledge on the development of nanostructured zirconia-based ceramics and composites suitable for application in dentistry. Isi Web of Science, Science Direct, Scientific.net databases, and Google were searched electronically for the period of 1980 to the present, matching the keywords “nano” with the keywords: “Zirconia, ZrO2, Y-TZP, and dental, dentistry”. A total of 74 papers were found, with the majority coming from Asia, indicating a more active scientific interest on the topic in this geographic area, followed by Europe, South America, and North America. The research shows, even though the scientific activity on nanostructured ceramics was intense in the last fifteen years, the development of fully dense zirconia-based nanoceramics is yet at an initial stage, most of all from the point of view of the clinical applications. It has been demonstrated that nanostructured ceramics can show improved properties because of the reduction of the grain size to the nanoscale. This is also true for zirconia-based nanoceramics, where some improvements in mechanical, optical, as well as resistance in low-temperature degradation have been observed. Potential applications of this class of material in the dental field are discussed, summarizing the results of the latest scientific research.

Background: Discordant opinions have emerged among clinicians and researchers regarding a digital impression for full-arch implant-supported fixed dental prostheses (FDPs). The purpose of this study was to assess the fit of screw-retained milled frameworks on six implants realized from digital impressions through the Sheffield test. Methods: One patient received a maxillary full-arch implant-supported FDP. Six months after the surgical procedure, ten intraoral full-arch digital impressions were performed to mill ten frameworks. To clinically assess the fit, the Sheffield test was applied for all frameworks. The gaps among the frameworks and the implant analogs were measured using a microscope on the master model realized with a traditional impression. The Wilcoxon sum-rank test was used to compare the misfit value among the different implant positions. Results: The Sheffield test did not show gaps in the framework–implant interfaces when the screw was completely tightened on the more distal implant for all the milled frameworks. The mean misfit value calculated after microscope examination was 38 ± 5 μm. Differences that were statistically significant emerged when the misfit values of central positions were compared with other values. Conclusions: The use of full-arch implant digital impressions represents a viable alternative to traditional impressions for the fabrication of implant-supported FDPs.

background: resin-bonded fixed dental prosthesis (RBFDP) represents a highly aesthetic and conservative treatment option to replace a single tooth in a younger patient. The purpose of this in vitro study was to compare the fracture strength and the different types of failure on anterior cantilever RBFDPs fabricated using zirconia (ZR), lithium disilicate (LD), and PMMA-based material with ceramic fillers (PM) by the same standard tessellation language (STL) file. Methods: sixty extracted bovine mandibular incisives were embedded resin block, scanned to design one master model of RBFDP with a cantilevered single-retainer. Twenty cantilevered single-retainer RBFDPs were fabricated using ZR, LD, and PM. Static loading was performed using a universal testing machine. Results: the mean fracture strength for the RBFDPs was: 292.5 Newton (Standard Deviation (SD) 36.6) for ZR, 210 N (SD 37.6) for LD, and 133 N (SD 16.3) for PM. All the failures of RBFDPs in ZR were a fracture of the abutment tooth, instead, the 80% of failures of RBFDPs in LD and PM were a fracture of the connector. Conclusion: within the limitations of this in vitro study, we can conclude that the zirconia RBFDPs presented load resistance higher than the maximum anterior bite force reported in literature (270 N) and failure type analysis showed some trends among the groups

The transfer of extraoral and intraoral clinical information into the virtual environment is necessary to optimize prosthetic treatment planning. The purpose of this article was to describe a digital workflow designed to superimpose the different 3D files obtained with an intraoral scanner, a cone bean computed tomography (CBCT) device, and a facial scanner and their clinical application with the Digital bite device.

PURPOSE To evaluate patient perception and operating time of digital (DW) and conventional (CW) workflows for the rehabilitation of a screw-retained, single-implant crown. MATERIALS AND METHODS A convenience sample of 10 patients with single implants in posterior sites was recruited for treatment with screw-retained single crowns, fabricated with either a DW or a CW protocol. Operating time and clinical adjusting time were recorded with a stopwatch, and patient preference and self-perception of the esthetic outcome were evaluated with a visual analog scale. RESULTS The mean operating time for the DW crowns was 16:21 minutes and for the CW crowns was 28:28 minutes. The mean total adjustment times were 118.1 seconds for the DW protocol and 181.5 seconds for the CW protocol. The mean score regarding self-perception of the esthetic outcome was 73 for DW crowns and 69 for CW crowns; for discomfort, the mean score was 15.5 for DW and 62 for CW. CONCLUSION The DW approach resulted in a time reduction for both the impression phase and operative time.

PURPOSE The study aims to evaluate three-dimensionally (3D) the accuracy of implant impressions using a new resin splinting material, "Smart Dentin Replacement" (SDR). MATERIALS AND METHODS A titanium model of an edentulous mandible with six implant analogues was used as a master model and its dimensions measured with a coordinate measuring machine. Before the total 60 impressions were taken (open tray, screw-retained abutments, vinyl polysiloxane), they were divided in four groups: A (test): copings pick-up splinted with dental floss and fotopolymerizing SDR; B (test): see A, additionally sectioned and splinted again with SDR; C (control): copings pick-up splinted with dental floss and autopolymerizing Duralay® (Reliance Dental Mfg. Co., Alsip, IL, USA) acrylic resin; and D (control): see C, additionally sectioned and splinted again with Duralay. The impressions were measured directly with an optomechanical coordinate measuring machine and analyzed with a computer-aided design (CAD) geometric modeling software. The Wilcoxon matched-pair signed-rank test was used to compare groups. RESULTS While there was no difference (p = .430) between the mean 3D deviations of the test groups A (17.5 μm) and B (17.4 μm), they both showed statistically significant differences (p

Implant site preparation through drilling procedures may cause bone thermonecrosis. The aim of this in vitro study was to evaluate, using a thermal probe, overheating at implant sites during osteotomies through 2 different drilling methods (continuous drilling technique versus intermittent drilling technique) using irrigation at different temperatures. Five implant sites 13 mm in length were performed on 16 blocks (fresh bovine ribs), for a total of 80 implant sites. The PT-100 thermal probe was positioned 5 mm from each site. Two physiological refrigerant solutions were used: one at 23.7°C and one at 6.0°C. Four experimental groups were considered: group A (continuous drilling with physiological solution at 23.7°C), group B (intermittent drilling with physiological solution at 23.7°C), group C (continuous drilling with physiological solution at 6.0°C), and group D (intermittent drilling with physiological solution at 6.0°C). The Wilcoxon rank-sum test (2-tailed) was used to compare groups. While there was no difference between group A and group B (W = 86; P = .45), statistically significant differences were observed between experimental groups A and C (W = 0; P =.0001), B and D (W = 45; P =.0005), and C and D (W = 41; P = .003). Implant site preparation did not affect the overheating of the bone. Statistically significant differences were found with the refrigerant solutions. Using both irrigating solutions, bone temperature did not exceed 47°C.

This article describes the case history of a 59-year-old female patient who sought advice for temporomandibular joint (TMJ) pain and sounds but who was actually diagnosed with a primary lung cancer with metastasis to the TMJ. The patient had a history of TMJ pain and deflection in jaw movement that progressively worsened over a few months and did not improve with the usual standard of care treatment provided by an orofacial pain practitioner. Magnetic resonance and computed tomography (CT) prescribed at a tertiary clinic showed an osteolytic bone mass within the right TMJ condyle. The neoformation was surgically removed and histologic assessment revealed it was a metastasis of a silent lung carcinoma. Thorax CT confirmed the presence of a formation within the apical segment of the right lung superior lobe. While this scenario of a silent lung cancer metastasis to the TMJ condyle mimicking classical symptoms of temporomandibular disorders (TMD) is rare, it does indicate that the path to differential diagnosis is often difficult in TMD and orofacial pain patients, and that practitioners managing such patients should be aware of the variegate spectrum of possible TMD-mimicking conditions to avoid dangerous diagnostic delays.

The aim of this retrospective study is to investigate the medium- to long-term prognosis of short implants in partially and totally edentulous patients with mandibular bone atrophy.The study involved 109 patients with 280 implants placed in the mandible. The implants were 7 or 8.5 mm long and 3.75 or 4 mm in diameter. The implant surfaces were machined (M; n = 176) or rough (R; n = 104). Patients were asked to attend a radiographic and clinical follow-up, and their previous clinical records and radiographs were assessed. Implant-related and prosthetic failures and complications were recorded.The mean follow-up was 9 years (range of 5 to 16 years). The survival rate (SSR) and success rate (SR) were calculated using life-table analysis for both M and R short implants. The M implants had a 16-year SSR of 95.7% and a corresponding SR of 93.9%, whereas the 16-year SSR and SR for the R implants were 97.2% and 95.2%, respectively. The mean ± SD bone resorption for all implants was 1.37 ± 0.5 mm. For marginal bone loss, there was no statistically significant difference between the two implant lengths (P = 0.38) or diameters (P = 0.34) or between the M and R implant surfaces (P = 0.47).Different implant lengths, diameters, and surface treatments do not appear to influence the prognosis of the implant. Within the limitation that most of the short implants were splinted to longer implants, the reduced length of the fixtures did not worsen the long-term survival of the implant-supported fixed prostheses.

The study aimed at evaluating the effect of chlorhexidine (CHX) in preventing plaque biofilm (PB) formation on healing abutments (HAs) in patients rehabilitated with osseointegrated implants.Fifty HAs were placed in 34 voluntary patients 1 week after implant surgery (test group). After 7 days, a new set of 50 HAs was placed in the same implant sites and removed 1 week after (control group). During the 2 testing periods, patients were instructed to apply: CHX mouth rinsing twice daily and no brushing (test); no CHX mouth rinsing and no brushing (control). Scanning electron microscopy and image analysis were blindly used to objectively quantify PB amount on removed HAs.Median values and interquartile ranges of the percent ratio of titanium surface covered from PB were 0.9 (0.1-4.1) and 1.2 (0.1-11.6) for test and control groups, respectively (P = 0.0275).CHX mouth rinsing significantly limited plaque formation on HAs, being a valid contribution to mechanical brushing in early phases of plaque control on dental implants.

Female patients on estroprogestinic therapy undergoing extraction of the third lower molar have a higher incidence of postoperative complications (dry socket -DS- pain). The purpose of this study is to verify such data and analyse if there are risk factors for the appearance of other postoperative complications.One hundred eighteen non-smoking healthy patients were included who underwent extraction of the impacted third lower molar (38 on oral contraceptives, OC, 80 as control). After the extraction, patients were prescribed with a pharmacological therapy, consisting of a per os antibiotic and antiseptic rinse. Each patient was examined after 7 days following surgery to verify the state of tissues. In addition subjective postoperative pain (VAS - Visual Analogue Scale) and intake of analgesic drugs were recorded.One case of DS (2.64%) occurred in the OC group, and 1 case of DS occurred in control-patients group (1.25%) (P=0.4436). The postoperative pain proved significantly higher in OC compared to control (first and fifth postoperation day). In OC a predisposition to dehiscence of the wound (86.84% P=0.0021) and emergence of laterocervical lymphadenitis (81.57% P=0.0010) was found, while no cases of postextractive abscesses and trismus of the masseter were found.Although no correlation between DS and estroprogestinic therapy has been found, a more difficult healing of tissues has been observed as well as a significantly higher subjective pain index in the postoperative days considered in OC patients.