Search

We employed a microwave-assisted two-pot in-situ deposition technique to incorporate zinc oxide particulates in the structure of filter paper to produce antimicrobial paper. The process involved successive immersion of filter paper samples in ZnSO4 (precursor solution) and NaOH (precipitating agent) to form Zn(OH)2, which transformed into ZnO during microwave treatment. Successful deposition of ZnO particles on the filter paper was confirmed via X-ray diffraction and the corresponding morphologies were observed using field emission scanning electron microscopy. The ZnO-deposited papers were tested for antimicrobial activity and were found to be more effective against Staphylococcus aureus (gram-positive) than Escherichia coli (gram-negative). Bacterial populations were reduced by up to 92 ± 2% and 57 ± 4% for S. aureus and E. coli, respectively. Also, it was found that the samples prepared using higher concentrations of ZnSO4 and NaOH exhibited better antimicrobial properties.

Free-standing flexible supercapacitive electrodes have practical application for wearable energy storage devices. In this paper, graphene paper (GP), a flexible electrode substrate, was prepared by one-step reduction of graphene oxide (GO) using HI solution. GP can be used independently as a flexible electrode with specific capacitance of 227 F/g. In order to make up for the shortage of GP specific capacitance storage, polyaniline (PANI) with high specific capacitance and good electrical conductivity was selected to composite with GP by electrochemical polymerization approach. This method to fabricate electrode material by direct electrochemical polymerization avoids the use of conductive binder and organic solvent. Owing to the specific capacitance contribution of PANI and GP, the PANI/GP composites exhibit higher specific capacitance when the polymerization time is 30 s and the polymerization voltage is 0.8 V. At 1 A/g current density, the specific capacitance of composite is up to 759 F/g, which is 3.34 times of neat GP.

The construction industry had approached a critical limit which led to the increase of cement production. The production of cement would cause a broader environmental implication. Cement production is a major source of carbon dioxide emission. Carbon dioxide gas contributes about 63.33% of global warming since the production of one ton of cement would emit about one ton of carbon dioxide to the environment. To mitigate this issue, the research community has investigated the use of waste materials that possess similar chemical properties with cement content as a material for partial cement replacement. The use of rice husk ash has shown to be a contending candidate in the literature. Therefore, this paper attempts at reviewing the performance of rice husk ash as partial cement replacement. It could be observed from the literature that concrete with 5% up to 15% of rice husk ash showed an equivalent performance to ordinary concrete in compressive, flexural, and tensile strength. Thus, rice husk ash can be used as a material replacement in concrete and reduces pollution that originates from cement production and open burning of rice husk.

The rapid economic growth and environmental concerns have led to high demands on paper and paper-based products in terms of variety, quantity, quality, and specialty. Enhancement and functionalization with additives are constantly required. Moving away from traditional petroleum-based additives, researchers have attempted to use “green” nanoadditives by introducing renewable environmentally friendly nanocellulose. This article studies the functions of nanocellulose as bio-additives (enhancer, retention and filtration reagent, and coating aid) in paper and paper products, and overviews the research development of nanocellulose-based additives and their applications in the paper industry for both efficient production and paper functionalization. The review shows that (1) a variety of nanocellulose-based bioadditives have been reported for various applications in paper and paper-based products, while commercially viable developments are to be advanced; (2) nanocellulose was mostly formulated with other polymer and particles as additives to achieve their synergistic effects; (3) major interests have concentrated on the nanocellulose in the specialty papers as representing more value added products and in the efficient utilization of recycled fibers, which remains most attractive and promising for future development. This report shall provide most useful database information for researchers and industries for paper recycling and enhancement, and paper-based products innovation and application.

The appearance and quick spread of the new severe acute respiratory syndrome coronavirus disease, COVID-19, brought major societal challenges. Importantly, suitable medical diagnosis procedures and smooth clinical management of the disease are an emergent need, which must be anchored on novel diagnostic methods and devices. Novel molecular diagnostic tools relying on nucleic acid amplification testing have emerged globally and are the current gold standard in COVID-19 diagnosis. However, the need for widespread testing methodologies for fast, effective testing in multiple epidemiological scenarios remains a crucial step in the fight against the COVID-19 pandemic. Biosensors have previously shown the potential for cost-effective and accessible diagnostics, finding applications in settings where conventional, laboratorial techniques may not be readily employed. Paper- and cellulose-based biosensors can be particularly relevant in pandemic times, for the renewability, possibility of mass production with sustainable methodologies, and safe environmental disposal. In this review, paper-based devices and platforms targeting SARS-CoV-2 are showcased and discussed, as a means to achieve quick and low-cost PoC diagnosis, including detection methodologies for viral genomic material, viral antigen detection, and serological antibody testing. Devices targeting inflammatory markers relevant for COVID-19 are also discussed, as fast, reliable bedside diagnostic tools for patient treatment and follow-up., The authors acknowledge funding through projects Eco2Covid (POCI-01-02B7-FEDER-068174) and TecniCov (POCI-01-02B7-FEDER-069745), co-funded by FEDER through COMPETE2020 and Lisboa2020. T.P., A.R.C. and A.C.M. acknowledge funding to National Foundation for Science and Technology, I.P., FCT, through their PhD grants, references DFA/BD/8606/2020, SFRH/BD/130107/2017 and SFRH/BD/115173/2016, respectively, info:eu-repo/semantics/publishedVersion

Graphene-based nanomaterials possess broad applications because of their excellent multi-functional properties. In this work, a facile self-assembling method was presented for preparing one kind of graphene oxide-based paper/hollow microspheres hybrid. It was found that most of the hollow microspheres can strongly anchored on the surface of graphene oxide paper (GOP) by an in-situ scanning electron microscope peeling testing combining with molecular dynamics (MD) simulation. In addition, the uniform distribution of hollow microspheres on the surface of GOP cannot only provide a better surface wettability, but also can effectively improve the interfacial stress-transfer capability between such hybrid and polymer matrix. Our work provides a guidance for the structural designs of graphene-based nanomaterials and broaden their applications.

Cellulose paper, a material that is naturally derived, low cost, lightweight, eco-friendly, and mechanically deformable, plays important roles in producing next-generation flexible electronics. Following the booms in the development of functional electronics, the soft actuators built from cellulose paper have attracted great attention. In this focused review, the milestones and recent achievements of cellulose paper-based actuators are summarized. Electro-, thermal, moisture and magnetic actuation mechanisms are utilized to acquire energy from external stimuli. Corresponding functional materials and available fabrication techniques like film assembly and layer deposition are described. Programmable actions for the emerging applications in bionics, paper grippers and robots are realized by pursuing different strategies to control the responding deformation. Along with a conclusion, the existing challenges and possible solutions in evaluating and improving the performance of cellulose paper are summarized in the final section.

Hydrothermal liquefaction derived hydrochar produced from industrial paper sludge was used as an adsorbent to remove phenol derivatives from an industrial wastewater stream. Removal efficiency for phenol was determined using synthetic solutions (10–150 ppm) using batch adsorption experiments at a constant solution pH (8), temperature (25 ± 2 °C) and rotary speed (150 rpm). The adsorption of phenol onto hydrochar followed a Freundlich isotherm and could be described with pseudo-second-order kinetic models. Analysis of the adsorption mechanisms showed that particle film mass transport was the rate-determining step in the adsorption process. A COD removal efficiency of 31 ± 1% was achieved for the industrial wastewater stream. All phenol components in the wastewater stream could be removed, but not all organic acids and cyclic ketones. The performance of the paper sludge-based hydrochar compared well with that of activated carbon (44% COD removal). The final phenol concentration in the wastewater stream was below the acceptable phenol concentration for industrial effluents (1 mg/L). The results show that paper sludge can be converted to a valuable marketable commodity that could reduce waste management costs for a paper mill, while also reducing the cost of expensive adsorbents. Highlights Industrial paper sludge waste was successfully converted to effective bio-adsorbent.; HTL-based biochar was used as adsorbent without any pretreatment.; 77.83% COD removal from industrial wastewater could be obtained.; Final total phenol concentration was below 1 ppm.; Bulk fluid mass transfer was the rate determining step in the adsorption process.

With the increased awareness of reusing solid wastes for higher sustainability and the concern of water pollution associated with phosphorus over-emission, there are strong interests in developing solid waste based adsorbents for purifying phosphorus-containing wastewater. As a rich calcium resource, paper mill sludge (i.e., a major solid waste from pulping industry) can be used as phosphorus removal adsorbent after calcination. Thus, in this work, a simple and clean thermally treating route has been proposed for preparing calcium-containing biochar from paper mill sludge. The effect of the physicochemical properties of paper mill sludge and its carbonization condition on phosphorus adsorption has been analyzed. Moreover, the influence of some key adsorption parameters, e.g., biochar dosage, initial pH of solution, co-existing anions, initial phosphorus concentration and contact time has also been investigated. The results showed that the phosphorus adsorption data could be fitted well with pseudo-second-order kinetic and Langmuir isothermal models. The calculated maximum adsorption capacity of the as-prepared optimal calcium-containing biochar could reach to 68.49 mg·g−1 at 25 °C. Combined with the characterization results, it can be reasonably inferred that the adsorption process was chemisorption-dominated. Lastly, the application of this spent adsorbent in agriculture field has also been discussed. In brief, this work provided a feasible strategy for converting paper mill solid waste to an environmental functional material (i.e., calcium-rich biochar) for remediation of eutrophic water.

Cellulose based nanomaterials have the great potential to be applied to paper as bulk additive or coating material to improve overall final properties, especially in secondary fiber. In the present work, the effect of applying different kinds of cellulose nanofibrils (CNF) to papers obtained from recycled fibers using size press on physical, mechanical and barrier properties was investigated and compared with the sole use of starch as coating material. The coating process of CNF was carried out by the addition of size press grade starch to coating suspension. As a cellulose source, wheat straw was evaluated and CNF was obtained through oxidative and enzymatic pretreatments. Results indicate that starch/CNF suspension improves the overall paper properties. As a result of the deposition of coating suspension contains of 4 % wt. periodate-oxidized CNF onto paper surface, tensile and burst indices of papersheets increased as 52.2 % and 194.4 %. Significant decreases were observed in air permeability as 69.8 %. Compression tests also have been conducted to evaluate papersheets end-use properties. In comparison to the other pretreated CNF, due to is lower viscosity, applying periodate-oxidized CNF as size press significantly increased the mechanical properties of the papers fabricated from the recycled pulps. TUBITAK-TEYDEBTurkiye Bilimsel ve Teknolojik Arastirma Kurumu (TUBITAK) [1505]; Scientific and Technological Research Council of Turkey, Technology and Innovation Funding Programs Directorate [1505, 5180044] This work was supported by TUBITAK-TEYDEB 1505 (The Scientific and Technological Research Council of Turkey, Technology and Innovation Funding Programs Directorate 1505), Project No. 5180044. WOS:000703585400013 2-s2.0-85108063350

This study optimizes a novel surfactant-assisted green liquor dregs (GLD) pretreatment of paper mill sludge (PMS), both of which are wastes from the kraft pulping industry, using a combined Response Surface Methodology (RSM) design. Optimized conditions give a maximal reducing sugar release of 16.38 g/L. A substantial reduction in heavy metals aluminum, chromium, cobalt, arsenic, lead, and copper after pretreatment illustrates the enhancement of substrate digestibility by reducing toxic elements. Separate hydrolysis and fermentation (SHF) and simultaneous saccharification and fermentation (SSF) for hydrogen production are assessed. SSF produced a hydrogen yield of 3.72 mL/g, displaying a 36.26% increase from pretreated PMS compared to SHF. These findings provide insights into possible methods of reducing process duration, energy input, and costs incurred with waste disposal within the paper industry. Furthermore, improved hydrogen yield using an SSF process demonstrates the potential beneficiation of pulp and paper GLD and PMS wastes.

The fiber of paper mulberry, which is mostly grown in the East Asian region, varies in both length and width—even if from the same species—depending on the country, soil, and climate where it is grown. This accounts for differences in the quality of handmade paper between domestic and imported products. Once handmade paper is manufactured as sheets, its origin cannot be determined from a morphological perspective, regardless of macroscopic and microscopic observations. Therefore, this study attempted to determine the origin of Korean and imported products using mulberry bast fiber and handmade paper from a chemometrics perspective. The inorganic components of wood are absorbed from the soil and exist in the bark of trees; thus, metal and rare-earth elements in the bast fibers and handmade papers were quantitatively analyzed using inductively coupled plasma-atomic emission spectroscopy/mass spectrometry (ICP-AES/MS). Following this, a prediction model of their origin was constructed by applying multivariate statistical analysis, i.e., a partial least squares-discriminant analysis (PLS-DA) loading plot was constructed, which helped in identifying the discrimination factors resulting from their origin. According to the ICP-AES results, Pb was only detected in the Gyeongbuk Mungyeong dak sample of the Korean bast fibers. The Chinese bast fiber sample had high contents of Ca, and B and Zn were detected only in the Chinese bast fiber samples. Bast fiber samples from China, Japan, and Thailand showed relatively high contents of Al, Ca, and Na. Meanwhile, Cu and Zn were detected in the handmade paper manufactured from the imported materials. According to the ICP-MS results, among the Korean handmade papers, the products from Gyeongbuk Mungyeong, Andong, and Chungbuk Goesan exhibited a high U content and that from Gapyeong had high Sc, Rb, Sr, and Ba contents. Thus, the elemental analysis employed in this study effectively identified the origin of the papers. The origin prediction by PLS-DA for the domestic and imported products revealed an accuracy of 86.4% and 72.7% for ICP-AES and ICP-MS methods, respectively, which is deemed acceptable to assess the origin. We believe this method significantly contributes to determining the origin of paper mulberry bast fiber and handmade paper manufactured in East Asia.

Lignin/tannin/ZnONP composite coatings were designed for paper-based green packaging. Multiple functions, such as high strength, moisture resistance, low air permeance, heat endurance, UV aging resistance, and antibacterial/mold properties, were successfully integrated into one biobased coating. Prepolymerization improved the physical properties of coatings at high lignin contents. The best ingredient ratio was: 40% lignin, 15% tannin, and 10% ZnONPs (based on tannin weight), and the as-prepared biocoating was labeled LTZn-10. After coated with LTZn-10, the tensile strength and bursting strength of the packaging were efficiently enhanced by more than 3 times and were dramatically increased by 51.6 and 5.6 times at the wet state, respectively, which reveals that the packaging has favorable moisture resistance and it can be used in high humidity environments. Scanning electron microscopy (SEM) proved that most of the pores on the paper were blocked by the coatings, which helped to decrease the air permeance by 10.3 times. Meanwhile, ZnONPs were evenly spread on the coatings, which endowed the packaging with excellent antibacterial/mold performance. No colony or mycelium was found in the test against Gram-negative/positive bacteria and eight common molds. Besides, antibacterial activity is only available while the bacteria come in contact with the coating and no active substances were released into the culture medium, which is a good property that can keep the cargo from contamination of antibacterial agents. In addition, the coated paper presented an improved Tg and thermal degradation temperature, indicating that the coated package has favorable thermostability and can maintain its outstanding physical properties in a wider temperature range. Lignin and tannin promoted the UV stability and service life of the coated paper, as a rare physical decrease was observed after UV aging for 72 h. The function-integrated biobased coating with favorable sustainability is a good candidate to be widely used in paper-based green packaging fields.

Funding Information: The financial support of the Austrian Federal Ministry of Digital and Economic Affairs and the National Foundation for Research, Technology and Development , Austria, is gratefully acknowledged. We also thank the industrial partners Mondi, Canon Production Printing, Kelheim Fibres, and SIG Combibloc for their support. Publisher Copyright: © 2021 Copyright: Copyright 2021 Elsevier B.V., All rights reserved. Hydrophobization of cellulosic materials and particularly paper products is a commonly used procedure to render papers more resistant to water and moisture. Here, we explore the hydrophobization of unsized paper sheets via the gas phase. We employed three different compounds, namely palmitoyl chloride (PCl), trifluoroacetic anhydride/acetic anhydride (TFAA/Ac2O)) and hexamethyldisilazane (HMDS) which were vaporized and allowed to react with the paper sheets via the gas phase. All routes yielded hydrophobic papers with static water contact angles far above 90° and indicated the formation of covalent bonds. The PCl and TFAA approach negatively impacted the mechanical and optical properties of the paper leading to a decrease in tensile strength and yellowing of the sheets. The HMDS modified papers did not exhibit any differences regarding relevant paper technological parameters (mechanical properties, optical properties, porosity) compared to the non-modified sheets. XPS studies revealed that the HMDS modified samples have a rather low silicon content, pointing at the formation of submonolayers of trimethylsilyl groups on the fiber surfaces in the paper network. This was further investigated by penetration dynamic analysis using ultrasonication, which revealed that the whole fiber network has been homogeneously modified with the silyl groups and not only the very outer surface as for the PCl and the TFAA modified papers. This procedure yields a possibility to study the influence of hydrophobicity on paper sheets and their network properties without changing structural and mechanical paper parameters.

Superhydrophobic surfaces have high potential in self-cleaning and oil-water separation applications. We developed a three-step method for the preparation of superhydrophobic filter paper. It involved citric acid (CA) pretreatment to activate cellulose fibers, coating with cellulose nanofibrils/functionalized silica (CNFs/m-SiO2) slurry to increase surface roughness, and grafting of hexadecyltrimethoxysilane (HDTMS) to enhance water resistance. The water contact angle (WCA) and siding angle (SA) of the prepared filter paper reached 151.5° and 7.5°, respectively. The results showed that, compared to the coated filter paper without the added CNFs, the coated paper with CNFs had higher retention of m-SiO2, thus roughness required for superhydrophobic surface was achieved. Further test under frequent abrasion and acid or alkali conditions showed that CA pretreatment improved the durability of superhydrophobic filter paper due to chemical crosslinking between the modified substrate and m-SiO2. Besides, the prepared superhydrophobic filter paper had outstanding self-cleaning property and high oil-water separation efficiency for various oil-water mixtures. Therefore, it is expected to be used for the treatment of oily wastewater.

Graphical abstract Enzyme-linked immunosorbent assay (ELISA) is widely used for the detection of disease biomarkers. However, it utilizes time-consuming procedures and expensive instruments, making it infeasible for point-of-care (POC) analysis especially in resource-limited settings. In this work, a multicolorimetric ELISA biosensor integrated on a paper/polymer hybrid microfluidic device was developed for rapid visual detection of disease biomarkers at point of care, without using costly equipment. This multicolormetric ELISA platform was built on multiple distinct color variants resulted from the catalytic oxidation of 3,3′,5,5′-tetramethylbenzidine (TMB) and the etching of gold nanorods (AuNRs). The vivid color changes could be easily distinguished by the naked eye, and their red mean values allowed quantitative biomarker detection, without using any sophisticated instruments. When this multicolorimetric ELISA was integrated on a paper/polymer hybrid analytical device, it not only provided integrated processing and high portability but also enabled fast assays in about 50 min due to the unique advantages of paper/polymer hybrid devices. The limit of detection of 9.1 ng/μL of the hepatitis C virus core antigen, a biomarker for hepatitis C, was achieved using this multicolorimetric ELISA platform. This multicolor ELISA analytical device provides a new versatile, user-friendly, affordable, and portable immunosensing platform with high potential for on-site detections of various viruses, proteins, and biomarkers for low-resource settings such as at home, public venues, rural areas, and developing nations. Supplementary Information The online version contains supplementary material available at 10.1007/s00216-021-03359-8.

The in-situ synthesis of calcium silicate in the fiber can not only meet the requirements for high loading of paper, but also make up and improve the reduction of paper performance caused by filling. In this investigation, the effects of pulp type, beating degree, fiber ratio, reaction time, rotational speed, dosage of lime milk and dispersant on calcium silicate loading and paper properties were investigated. The results showed that when the beating degree was 40 °SR, the ratio of softwood and hardwood pulp was 1:1, the reaction time was 60 min, the rotation speed was 600 r·min−1, the dosage of lime milk was 1.33 times of the theoretical amount, and the dosage of cationic polyacrylamide was 0.3 % (absolutely dry pulp), the ash content of hand-made sheet was 41.2 %, and the loading amount of calcium silicate was 26.3 %. Under this condition, the comprehensive performance of paper was the best.

A simple electrochemical approach has been strategically developed for in situ generations of ZnO nanoparticles using Zn rods as electrodes and hydrogen peroxide as the oxidant without the formation of any by-product. These ZnO nanoparticles were extended for remediation of pollutants present in paper mill effluents, and separation efficiency was found to be above 90% for hydrocarbons, 92% for lignin, 99% for phenol, and 93% of chemical oxygen demand (COD), as confirmed by gas chromatography-mass spectrometry and COD analysis. It was also observed that the experimental setup could successfully remove 99% of the color from the sample. These ZnO nanoparticles have been proven in the past to be antibacterial and were explored for its ability to inhibit the growth of both Gram-positive and Gram-negative bacteria in the effluent samples after the removal of toxic pollutants. Therefore, we proposed an electrochemical reaction for the in situ synthesis of ZnO nanoparticles for remediation of paper mill effluent as well as inhibit the bacterial growth in the treated effluent sample.

Graphical abstract During epidemics, such as the frequent and devastating Ebola virus outbreaks that have historically plagued regions of Africa, serological surveillance efforts are critical for viral containment and the development of effective antiviral therapeutics. Antibody serology can also be used retrospectively for population-level surveillance to provide a more complete estimate of total infections. Ebola surveillance efforts rely on enzyme-linked immunosorbent assays (ELISAs), which restrict testing to laboratories and are not adaptable for use in resource-limited settings. In this manuscript, we describe a paper-based immunoassay capable of detecting anti-Ebola IgG using Ebola virus envelope glycoprotein ectodomain (GP) as the affinity reagent. We evaluated seven monoclonal antibodies (mAbs) against GP—KZ52, 13C6, 4G7, 2G4, c6D8, 13F6, and 4F3—to elucidate the impact of binding affinity and binding epitope on assay performance and, ultimately, result interpretation. We used biolayer interferometry to characterize the binding of each antibody to GP before assessing their performance in our paper-based device. Binding affinity (KD) and on rate (kon) were major factors influencing the sensitivity of the paper-based immunoassay. mAbs with the best KD (3–25 nM) exhibited the lowest limits of detection (ca. μg mL−1), while mAbs with KD > 25 nM were undetectable in our device. Additionally, and most surprisingly, we determined that observed signals in paper devices were directly proportional to kon. These results highlight the importance of ensuring that the quality of recognition reagents is sufficient to support desired assay performance and suggest that the strength of an individual’s immune response can impact the interpretation of assay results. Supplementary Information The online version contains supplementary material available at 10.1007/s00216-021-03317-4.

In this research, simultaneous quantification of cysteine (Cys) and histidine (His) using a paper-based sensor was investigated for the first time. A microfluidic paper-based sensor is a promising amino acid determination tool due to its low cost, low sample consumption, and fast analysis and is easy to make. We used SBA-15 as porous materials that are crystalline compounds formed with surfactants and TEOS as a silica source. The SBA-15 sample was characterized by X-ray diffraction, Fourier transform infrared, and scanning electron microscope techniques. The microfluidic paper-based sensors were fabricated using a wax pen, and the mesoporous SBA-15 modified filter paper. The fabricated sensors for Cys and His determination are operated based on an indicator-displacement assay. A comparative determination study of Cys and His on the sensors was carried out. The results illustrated that the addition of silica nanoporous material led to an immediate and uniform color change. The sensors were successfully exploited in the simultaneous determination of urinary Cys and His levels, thus providing the potential opportunity for clinical diagnosis. The linear range of 1.0 to 90.0 μM and 1.0 to 100 μM for His and Cys was obtained from the calibration data. The detection limits were also calculated (S/N = 3) for His and Cys of 0.5 μM and 1.5 μM, respectively. The proposed method showed a good agreement with the results achieved by a standard method.

A high-barrier, strong, and antibacterial paper was fabricated by coating the acetylated cellulose solution with different contents of cinnamaldehyde (CIN) on Kraft paper. The antibacterial, antioxidant, mechanical, and barrier properties of coated paper were investigated. When the amount of CIN added in coating reached 6% v/v, the coated paper exhibited excellent antioxidant activity and antibacterial activity against Escherichia coli and Staphylococcus aureus. Notably, the dry and wet tensile strength of paper after coating was increased by 26.4 and 10.6 MPa, respectively. Furthermore, the coated papers' barrier properties against oil, water, water vapor, and oxygen were dramatically improved, especially for the water barrier rate up to 96.4%. Our coated papers with over 6% v/v CIN could extend beef's shelf-life for at least 4 days, which exhibited a promising prospect in eco-friendly antibacterial packaging.

A newly developed research topic, fabricated paper-based microfluidic sensors, was discussed in the field of low-cost environmental detection. Distinguished with the traditional dipstick or lateral-flow setups, these paper-based microfluidic sensors can serve as a tool for onsite quantitative and semi-quantitative measurements, without risks to cause environmental pollution. They have attracted increasing interest since the first easy-fabricated paper-based setup reported by Whitesides group in 2007. Most of the publications utilized paper-based sensors in clinical detection. In recent years, some groups started to use these sensors in environmental measurement, leading to precise, easy operation, low-cost, and eco-friendly methods for onsite detection. In this review, paper-based microfluidic sensors were briefly introduced, followed by literatures review and discussion for future perspectives.

BackgroundThe analysis of the quality of food is important to protect humans from food-borne or food-based illnesses caused by pathogens, such as bacteria, fungi, viruses, and protozoa. Rapid identification of these pathogens is critical to ensure food safety. Various detection and identification strategies exist; however, they are laborious and time consuming and hence the detection takes longer time. The aim of this study was to develop the specific and fast method for the detection of contaminants in milk.ResultsIn this study, we have developed a simple paper-based PCR method with minimum sample preparation process. The 16S rDNA universal primers were used for the detection of bacterial contaminants. LacZ primers were used for coliform detection which causes serious illness and hence their detection is crucial. ITS region primers were used for fungal detection. The most unique thing about this study is use of Whatman paper no. 1 as sample carrier material. We developed and validated the paper-based PCR method and used it for the detection of microbes and coliforms using milk as a representative sample.ConclusionWe evaluated this method for its suitability in the detection of contaminant microbes using different milk samples. The paper-based method could successfully detect contaminants in the milk samples and the results were comparable to the traditional microbial detection method. The traditional microbiological method takes at least 18–20 h for detecting the presence of microbes in any sample but the developed paper-based PCR method can confirm the microbial presence in 2–3 h. This is very promising especially in the testing where sample sterility is crucial.

The present study reports the characterization of reverse osmosis (RO) technology at water treatment plant Cogen-2 in paper and Board mills, Pakistan. RO is a commonly used process to obtain de-mineralized water for high-pressure boiler operation in thermal power plants. Scaling and fouling in three-stage RO plants is a major challenge in chemical industry due to the use of raw brackish water in the power plant of paper and board mills. In our study, the feed water quality of RO was changed from soft water to raw water to make it economical. The cleaning frequency was increased three times than normal, which was unsafe for operation and it was required to control scaling and fouling to achieve the desired result. Differential pressures behavior of all stages for 2-month data was observed without acid treatment, and the results of Langelier Saturation Index (LSI) control parameters (temperature, pH, total dissolved solids, calcium hardness, and alkalinity) clearly showed the abnormality. To optimize scaling and fouling of RO, the LSI factor was controlled in total reject water for the next 2 months by acid treatment in feed water. Duration of chemical cleaning and membranes’ life has been extended by fouling and scaling control. Understanding the effect of operational parameters in RO membranes is essential in water process engineering due to its broad applications in drinking water, sanitation, seawater, desalination process, wastewater treatment, and boiler feed water operation. The product flow increased from 18.3 to 19.9 m3/h, and this was due to a decrease in the rejection flow from 8.2 to 6.7 m3/h. The total reject stream pressure also increased from 8.1 to 9 bar. A lower value of LSI of 1.6 is obtained in the reject water stream after the acid treatment.

Environmentally friendly and energy saving treatment of black liquor (BL), a massively produced waste in Kraft papermaking process, still remains a big challenge. Here, by adopting a Ni CaO Ca12Al14O33 bifunctional catalyst derived from hydrotalcite-like materials, we demonstrate the feasibility of producing high-purity H2 (∼96%) with 0.9 mol H2 mol−1 C yield via the sorption enhanced steam reforming (SESR) of BL. The SESRBL performance in terms of H2 production maintained stable for 5 cycles, but declined from the 6th cycle. XRD, Raman spectroscopy, elemental analysis and energy dispersive techniques were employed to rationalize the deactivation of the catalyst. It was revealed that gradual sintering and agglomeration of Ni and CaO and associated coking played important roles in catalyst deactivation and performance degradation of SESRBL, while deposition of Na and K from the BL might also be responsible for the declined performance. On the other hand, it was demonstrated that the SESRBL process could effectively reduce the emission of sulfur species by storing it as CaSO3. Our results highlight a promising alternative for BL treatment and H2 production, thereby being beneficial for pollution control and environment governance in the context of mitigation of climate change.

By continuously varying the structure of graphene oxide paper (PRGP) using Joule heating annealing, we are able to tune its electrical conductivity (σ) and thermal diffusivity (α) in a very wide range: more than three orders of magnitude for σ (186–503009 S/m) and 10-fold for α (8.31 × 10−7 m2/s to 9.31 × 10−6 m2/s). Excellent coherency-linear relationship between σ and α is discovered although they are sustained by different carriers: electrons and phonons. Such coherency exists over two sections: σ > 2 × 104 S/m, and 103

Currently, most of the collected waste medium-density fiberboards (MDF) is incinerated or landfilled, as economically viable recycling methods are yet to be developed. By steam refining waste medium-density fiberboards (MDF), it is possible to hydrolyze the incorporated resins and isolate a high yield fiber fraction. Further refining of the steam treated fibers might enable the fibers to be utilized in applications such as paper packaging, facilitating a cascading use of the waste material stream. To this end, intimate knowledge of the material is needed. In this study, the steam refined fibers of two waste MDF samples containing differing amounts of softwood and hardwood underwent refining and beating. The resulting fibers were characterized regarding their morphology and paper test sheets were produced to evaluate their strength (compression-, tensile- and tear-strength). Distinct differences in response to refining between the MDF samples were apparent. For the sample with the higher hardwood share an increase in strength properties with increasing steam treatment severities could be observed and it was possible to produce test sheets with comparable compression strength to recycled pulp for industrial corrugated paperboard. For the sample with a higher share of softwood, the steam treatment severity did not show any influence on fiber morphology or paper properties, and the resulting paper strength was low in comparison to the other steam refined waste MDF sample. Graphic Abstract

Cellulose nanofibers isolated from unbleached pulp are characterized by different surface properties due to presence of lignin at their surface, in addition to lower cost than isolated from bleached pulp. In the current work, the effect of cellulose nanofibers isolated from unbleached neutral sulfite and bleached soda rice straw pulps (so called UBCNF and BCNF) on improving paper sheet properties of unbleached and bleached rice straw pulp (so called UBP and BP) was studied. The effect on mechanical properties (tensile strength, burst strength, and tearing resistance) and physical properties (porosity and water vapor permeability) was studied. Scanning electron microscopy (SEM) was used to assist in explaining the obtained results. The result showed that using BCNF and BP resulted in better improvement in mechanical properties and also more effective in reducing porosity of paper sheets than in case of using UBCNF and UBP. These results indicated stronger bonding between nanofibers and pulps’ fibers in case of using BCNF and BP (surfaces rich in cellulose hydroxyl groups) than in case of UBCNF and UBP (surfaces rich in lignin). Water vapor permeability of paper sheets made from unbleached or bleached pulps did not significantly affect by the addition the nanofibers.

The development of industry and of the Internet of Things (IoTs) have brought energy issues and huge challenges to the environment. The emergence of triboelectric nanogenerators (TENGs) has attracted wide attention due to their advantages, such as self-powering, lightweight, and facile fabrication. Similarly to paper and other fiber-based materials, which are biocompatible, biodegradable, environmentally friendly, and are everywhere in daily life, paper-based TENGs (P-TENGs) have shown great potential for various energy harvesting and interactive applications. Here, a detailed summary of P-TENGs with two-dimensional patterns and three-dimensional structures is reported. P-TENGs have the potential to be used in many practical applications, including self-powered sensing devices, human–machine interaction, electrochemistry, and highly efficient energy harvesting devices. This leads to a simple yet effective way for the next generation of energy devices and paper electronics.

Research by the paper industry into new materials to expand the raw material base for pulp is on the ascendancy due to growing demand for pulp and paper products. This study assessed the anatomical...

Cellulose triacetate (CTA) forward osmosis (FO) membrane from Hydration Technology Innovation (HTI), USA was tested in a locally fabricated FO system to concentrate synthetic and pulp and paper mill wastewater. The industry is among the 17 most polluted industries with intensive water consumption and wastewater generation (MoEFCC, Government of India). The CTA membrane was studied with deionized water as feed solution and 1 M NaCl as draw solution, which resulted into water flux of 5.8 L/m2h and reverse salt flux of 0.2 g/L. A concentration stepping method was used to determine the critical draw concentration with lignin solution as the model feed. There was no deviation in flux between the baseline (deionized water feed) and the lignin solution up to 1.5 M NaCl, but a marginal deviation (8% and 21% respectively at 2 M and 3 M) was seen thereafter. The average water flux after 24 h FO study with synthetic wastewater as feed solution (draw solution 2 M NaCl) was 8 L/m2h, and 80% water recovery. Similar study with pulp and paper wastewater as feed solution (draw solution of 1.5 M NaCl) was 5.4 L/m2h was with 62% water recovery. Lignin and COD rejection in pulp and paper mill wastewater was 90% and 64% respectively. The preliminary results indicate that FO is promising for water and lignin recovery from waste streams.

Paper and pulp mills generate substantial quantities of cellulose-rich sludge materials that are disposed in landfills at a large scale. For sustainability purposes, sludge materials can be bioprocessed to produce renewable fuels and useful chemicals. The enzymatic hydrolysis of cellulose is the process bottleneck that affects the conversion economics directly by using zero-cost raw materials. In order to study and optimize the process, the characteristics of the sludge raw materials should be first evaluated. In this work, sludge samples were obtained from paper mills located at different locations in Wisconsin and Minnesota. Part of the sludge samples was washed (de-ashed) with hydrochloric acid while the other part remained unwashed. The samples were subjected to multiple spectroscopic analyses techniques to evaluate the morphological properties of cellulose fibers and to estimate the total structural carbohydrate content. The results showed that the de-ashing process changed some fiber characteristics and cellulose crystallinity structure in all sludge samples. Sludge sample A (obtained from Kraft pulp and recycled paper mill region) showed a high percentage of fiber, with crystalline cellulose, compared to the other two sludge samples suggesting that sludge A is a valuable source to make value-added products. Aspen Plus mass and energy calculations performed in view of the ‘zero’ cost and the reliable supply of sludge raw materials producing 2 mol H2/mol glucose. Moreover, the results showed that extracting crystalline cellulose from these sludge samples is more profitable than crystalline cellulose made from the other lignocellulosic feedstocks. The results reported here showed that the utilization of these sludge materials would be an economically attractive and promising alternative for the production of hydrogen.

Virgin pulp is made by splitting up cellulose fibers from the woods by mechanical and chemical process without adding any recycled pulp content. The demand for trees, which are the basic raw material for making virgin pulp, increasing constantly in enormously growing paper manufacturing industry. The paper, which is made from virgin pulp is called as virgin paper and this is considered as better quality paper than the recycled paper. Now there is a need to increase the quality of recycled paper to equalize the quality of virgin paper, to reduce the demand for trees to make virgin pulp. In recycling, dispersive system is responsible for the de-inking process, which is one of the pulp purifying process which removes the printing ink from fibers. Chemicals are added in this deinking process which causes a serious problem by increasing the chemical concentration level of industrial outlet water. In conventional deinking technology, dispersive system is controlled by DCS which is quite complicated to control complex loop of operations. To overcome these problems, the dispersive system operations are controlled by PLC along with sensors which make the process easier and replacing the chemicals with enzymes will reduce the chemical concentration level of industrial outlet water and increases the quality of paper.

Rewritable paper is meaningful to the recyclable and sustainable utilization of environmental resources and thus has been extensively investigated for several decades. In this work, we demonstrated an efficient and convenient strategy to fabricate rewritable paper based on reversible hydrochromism of donor-acceptor Stenhouse adducts (DASAs). The kinetics and efficiency of isomerization could be well-controlled by adjusting the surrounding temperature and humidity. Monocolored rewritable paper was prepared by coating cyclic DASA·xH2O on the paper surface. Writing, printing, stamping and patterning were realized on the rewritable paper. The information could be controllably erased by treatment in a humid atmosphere. More importantly, the rewritable paper was upgraded to multicolored by combination of two DASA materials. The color of chirography was switched by controlling the writing speed.

The salivary glands are closely associated with stress conditions and the neuroendocrine system. The concentrations of these salivary biomarkers fluctuate with a person’s disease status. Until now, salivary diagnostics have been promising; however, the analytical tools for detecting salivary biomarkers have remained burdensome due to the lack of user-friendly and cost-effective equipment. In this study, we used a microfluidic starch-coated paper-based chip to isolate ɑ-amylase from human saliva. The concentration of ɑ-amylase on the head and tail sections of the paper-based chip was compared in the presence or absence of starch. We found that ɑ-amylase was highly concentrated only in the head section of the starch-coated paper-based chip through Western blotting (WB) and enzyme-linked immunosorbent assay (ELISA). We expect our designed paper-based chip will aid in α-amylase detection technologies using saliva and small amounts of other biofluids including blood, tears, pancreatic juice, and urine.

In this elucidation, we synthesized novel molecularly imprinted polymers (MIPOH1-4) that were used as organic fillers on bagasse pulp to form cellulosic paper sheets, the formation of MIPOH1-4 from the reaction of enaminone 3 with methyl methacrylate monomer in the presence of ethylene glycol dimethyl acrylate and 2,2’-azobisisobutyronitrile. The obtained MIPOH1-4 was confirmed via FT-IR and SEM with different pore sizes. And we noticed that the increase of template 3 increases the hydrogen bond between monomer and template and gave sponge surface of MIPOH4. Furthermore, the computational energies of the template with different monomers utilize DFT/B3LYP/6-31G (d) level to know the stability of polymers and hydrogen bonding between them. So that we applied that in paper manufacture through the adsorption of MIPOH4 as an organic filler on bagasse pulp to form novel cellulosic paper sheets with different concentrations and these sheets which characteristic through FT-IR, SEM, sizing test, tensile strength, and elucidation their antimicrobial activity with theoretical and docking studies. The MIPOH4 and cellulosic paper sheets showed the thermal stability and high tendency of sizability of these paper sheets and concluded the interaction between cellulose fibers of pulp with MIPOH polymer with physical hydrogen bonding.

One of the most cited limitations of biochemical detection is its poor sensitivity, owing to the relatively high complexity of micro-samples. Moreover, some samples cannot be easily self-replicated and their abundance cannot be increased through traditional technologies. Therefore, the preconcentration of low-abundance samples is a key requirement for microfluidic biological analysis. In recent years, the ion-concentration polarization phenomenon has aroused widespread interest in the application of microfluidic technology. In addition, paper-based materials are readily available, easy to modify, and exhibit good hydrophilicity. The study of the ion-concentration polarization preconcentration of micro-samples in paper-based microfluidic chips is of considerable significance. In this review, we discuss the development and applications of ion-concentration polarization paper-based preconcentrator in the past 5 years, with emphasis on key progresses in chip fabrication and performance optimization under different conditions. The current needs and development prospects in this field have also been discussed.

Microfluidic paper-based analytical devices (μPADs) have developed rapidly in recent years, because of their advantages, such as small sample volume, rapid detection rates, low cost, and portability. Due to these characteristics, they can be used for in vitro diagnostics in the laboratory, or in the field, for a variety of applications, including food evaluation, disease screening, environmental monitoring, and drug testing. This review will present various detection methods employed by μPADs and their respective applications for the detection of target analytes. These include colorimetry, electrochemistry, chemiluminescence (CL), electrochemiluminescence (ECL), and fluorescence-based methodologies. At the same time, the choice of labeling material and the design of microfluidic channels are also important for detection results. The construction of novel nanocomponents and different smart structures of paper-based devices have improved the performance of μPADs and we will also highlight some of these in this manuscript. Additionally, some key challenges and future prospects for the use of μPADs are briefly discussed.

Plant fiber classified as environmentally friendly material is a promising renewable engineering material rich in lignocellulose that can be employed in the pulp and paper industry as a substitutio...

All-cellulose paper-based composites with underwater superoleophobicity and high-wet-strength were developed by casting a barrier layer of bacterial cellulose (BC) on a filter paper substrate. To optimize the pore structure of barrier layer, slow gel process of BC dispersion was conducted via acidification and solvent exchange. 1,2,3,4-butanetetracarboxylic acid was used to improve the wet strength and surface hydrophilicity through the crosslinking reaction between fibers. The underwater oil contact angles are higher than 150° in neutral environment, and slightly decrease under acid and alkali conditions. Combined with the micron-sized pore structure of BC barrier layer, the composite papers show good separation performance of oil-in-water emulsion. A denser BC layer can significantly improve the separation efficiency, but also lead to the reduction of flux. During the gelation of BC barrier layer, the increase in the ethanol/water ratio of the dispersion medium is able to increase the flux without obvious negative impact on the separation efficiency. When the ethanol/water ratio is 80%, the separation efficiency and water flux reach 99.2% and 1320 L m−2 h−1·bar−1 for the emulsified soybean oil with the average size of 13 μm, respectively. This type of all-cellulose composite papers provides a new idea for the fabrication of membrane materials for oil–water separation.

Cellulose bromo-isobutyl ester was prepared using filter paper as raw material through esterification reaction with 2-Bromoisobutyryl bromide (BIBB) in N, N-Dimethyl-formamide (DMF). Cellulose esters with different degree of substitution were obtained. FTIR result indicated the successful introduction of bromo isobutyryl group in cellulose to obtain cellulose ester (Cell-Br). The surface of modified filter paper become rough and grooves could be observed by SEM. The thermal stability of the cellulose ester decreased in comparison with unmodified filter paper. Besides, the hydrophobicity of the filter paper was improved and the water contact angle increased from 73.4° to 116.5° with increasing degree of substitution. The water vapor barrier property was improved by 26 %. Furthermore, it was also found the modified filter paper possessed antibacterial activity against S. aureus bacteria. The modified filter paper obtained could be potentially used in food packaging fields and the results provide a simple method to prepare functional filter paper.

The dispute over the paternity of western paper is a longstanding problem. In Italy, a country that has a long tradition of papermaking, many cities compete for the leadership in the production of this material; on the other hand, several studies attribute to Fabriano (13th century), a little center in Marche region, the birth of modern paper and its diffusion throughout Europe. During the 14thcentury, the nearby town of Camerino imposed itself on the paper market, triggering a historic rivalry with the manufacture of Fabriano. As scientific studies on these different productions are missing, a comparative, multidisciplinary investigation has been carried out to characterize a set of thirteenth-fifteenth century handmade papers from Camerino-Fabriano area. Several analytical techniques–some non-invasive such as Fourier-transform infrared spectroscopy (FTIR) and portable magnetic resonance (unilateral NMR), joined to micro-destructive ones such as scanning electron microscopy (SEM), 13C CPMAS NMR spectroscopy, thermo-gravimetric analysis (TGA), sodium dodecyl sulphate-polyacrylamide gel electrophoresis (SDS-PAGE) and reverse-phase liquid chromatography (RP-HPLC)–have been employed in order to study the morphology of the paper documents, to identify the substances used in production process and to define their preservation state. Moreover principal component analysis (PCA) has been applied to the spectroscopic data, allowing the clustering of Fabriano documents with respect to Camerino ones and dividing the samples in two sets. This work improves and confirms knowledges on paper production in Marche region, and the experimental data collected highlight similarities and differences between Camerino and Fabriano manufactures.

A paper-based membrane coated by graphitic carbon nitride (g-C3N4) is prepared via a dip-coating method and used as a separator for sodium metal batteries with merits of low cost and environment-friendliness. Introduction of g-C3N4 effectively improves the ionic conductivity and the structural stability of the separator. Compared with traditional polyethylene separators and Al2O3-coated separators, the g-C3N4-coated separators show better electrolyte wettability, thermal stability, and electrochemical stability. Therefore, Na||Na3V2(PO4)3 battery using the g-C3N4-coated separator exhibits better cycling stability and higher rate capability. These results prove that the g-C3N4-coated paper-based separator is expected to become the next generation of low-cost and high-safety separator in sodium metal batteries.

Compared with a single chemical indicator, the use of multivariate chemical indicators in aging status assessment of transformer cellulose paper insulation can improve the reliability of the evaluation. In this study, a non-destructive method based on multivariate chemical indicators was proposed to evaluate the remaining life of cellulosic paper insulation. The selected chemical indicators closely related to the aging of the insulating paper were analyzed. Additionally, by applying the subjective and objective weighting method, the evaluation information of each indicator was fully extracted to obtain reasonable comprehensive evaluation weights. Besides, the comprehensive evaluation index of multivariate chemical indicators was obtained by using the technique for order preference by similarity to ideal solution method, which is consistent with the deterioration law of paper insulation. Then, the correlation lifespan model between the comprehensive evaluation index of multivariate chemical indicators and the degree of polymerization of insulating paper under different aging stages was established. The effectiveness of the proposed model was verified by experiments. This promising model can increase the accuracy of the condition assessment for the transformer cellulosic paper insulation.

Flexible paper-based sensors may be applied in numerous fields, but this requires addressing their limitations related to poor thermal and water resistance, which results in low service life. Herein, we report a paper-based composite sensor composed of carboxylic carbon nanotubes (CCNTs) and poly-m-phenyleneisophthalamide (PMIA), fabricated by a facile papermaking process. The CCNT/PMIA composite sensor exhibits an ability to detect pressures generated by various human movements, attributed to the sensor's conductive network and the characteristic "mud-brick" microstructure. The sensor exhibits the capability to monitor human motions, such as bending of finger joints and elbow joints, speaking, blinking, and smiling, as well as temperature variations in the range of 30-90 °C. Such a capability to sensitively detect pressure can be realized at different applied frequencies, gradient sagittas, and multiple twists with a short response time (104 ms) even after being soaked in water, acid, and alkali solutions. Moreover, the sensor demonstrates excellent mechanical properties and hence can be folded up to 6000 times without failure, can bear 5 kg of load without breaking, and can be cycled 2000 times without energy loss, providing a great possibility for a long sensing life. Additionally, the composite sensor shows exceptional Joule heating performance, which can reach 242 °C in less than 15 s even when powered by a low input voltage (25 V). From the perspective of industrialization, low-cost and large-scale roll-to-roll production of the paper-based sensor can be achieved, with a formed length of thousands of meters, showing great potential for future industrial applications as a wearable smart sensor for detecting pressure and temperature, with the capability of electric heating.

The plasmonic properties of gold nanoparticles (AuNPs) are a promising tool to develop sensing alternatives to traditional, enzyme-catalyzed reactions. The need for sensing alternatives, especially in underdeveloped areas of the world, has given rise to the application of nonenzymatic sensing approaches paired with cellulosic substrates to biochemical analysis. Herein, we present three individual, low-step, wet-chemistry, colorimetric assays for three target biomarkers, namely, glucose, uric acid, and free cholesterol, relevant in diabetes control and their translation into paper-based assays and microfluidic platforms for multiplexed analysis. For glucose determination, an in situ AuNPs synthesis approach was applied into the developed μPAD, giving semiquantitative measures in the physiologically relevant range. For uric acid and cholesterol determination, modified AuNPs were used to functionalize paper with a gold-on-paper approach with the optical properties changing based on different aggregation degrees and hydrophobic properties of particles dependent on analyte concentration. These paper-based assays show sensitivity ranges and limits of detection compatible for target analyte level determination and detection limits comparable to those of similar enzymatic, colorimetric systems, relying only on plasmonic transduction without the need for enzymatic activity or other chromogenic substrates. The resulting paper-based assays were integrated into a single 3D, multiplex paper-based device using paper microfluidics, showing the capability for performing different colorimetric assays with distinct requirements in terms of sample flow and sample uptake in test zones using a combination of both horizontal and vertical flows inside the same device. The presented device allows for multiparametric, colorimetric measures of different metabolite levels from a single complex sample matrix drop using digital color analysis, showing the potential for development of low-cost, low-complexity tools for diagnostics toward the point-of-care.

Gelatine sizing was used extensively for western papermaking before the nineteenth century and this technique is still applied nowadays for restoration purposes. Despite its wide use, the relationships between gelatine types, the strength of the size and its distribution inside the paper sheet are still unclear. Different concentrations of three gelatines of various origins and types (A/B) were used to size model papers. The gelatine uptake, the strength of the size and the presence of gelatine at the papers surface were investigated by using a water drop test method and ATR-FTIR spectroscopy. At a given concentration, similar uptakes were found for all gelatines but great variations were observed in terms of size strength and of gelatine ability to cover the surface of paper sheets. In addition, Scanning transmission X-ray microscopy was performed on paper fibres cross sections to map the distribution of the organic compounds (both cellulosic and proteinaceous) on a nanometer scale. This showed that gelatine coats but does not penetrate the fibres. It can be inferred that the different size strengths observed between the tested gelatines are mainly due to different ways of filling holes between fibres inside the paper mat, some gelatines being more prone to go inside the sheet than others which remain mostly distributed near the surface.

Loop-mediated isothermal amplification (LAMP) has been widely used to detect many infectious diseases. However, minor inconveniences during the steps of adding reaction ingredients and lack of simple color results hinder point-of-care detection. We therefore invented a fluorometric paper-based LAMP by incorporating LAMP reagents, including a biotinylated primer, onto a cellulose membrane paper, with a simple DNA fluorescent dye incubation that demonstrated rapid and accurate results parallel to quantitative polymerase chain reaction (qPCR) methods. This technology allows for instant paper strip detection of methicillin-resistant Staphylococcus aureus (MRSA) in the laboratory and clinical samples. MRSA represents a major public health problem as it can cause infections in different parts of the human body and yet is resistant to commonly used antibiotics. In this study, we optimized LAMP reaction ingredients and incubation conditions following a central composite design (CCD) that yielded the shortest reaction time with high sensitivity. These CCD components and conditions were used to construct the paper-based LAMP reaction by immobilizing the biotinylated primer and the rest of the LAMP reagents to produce the ready-to-use MRSA diagnostic device. Our paper-based LAMP device could detect as low as 10 ag (equivalent to 1 copy) of the MRSA gene mecA within 36-43 min, was evaluated using both laboratory (individual cultures of MRSA and non-MRSA bacteria) and clinical blood samples to be 100% specific and sensitive compared to qPCR results, and had 35 day stability under 25 °C storage. Furthermore, the color readout allows for quantitation of MRSA copies. Hence, this device is applicable for point-of-care MRSA detection.

Natural cellulose paper is flame retarded using ammonium polyphosphate/montmorillonite (APP/MMT) nanocompound through coating method. Their morphologies are assessed by scanning electron microscopy, chemical components by energy dispersive X-ray spectroscopy and X-ray photoelectron spectroscopy, chemical structure by Fourier transform infrared, thermal stability by thermo-gravimetric analysis and fire retardancy by 45° horizontal burning test. The results show that the thermal stability and flame retardancy of coated paper samples are enhanced obviously, and all samples are self-extinguishing during the tests due to the char formation reaction between APP/MMT and cellulose. Then the treated paper, AM-18.3, as surface flame retardant treatment for low specific surface area (SSA) polypropylene (PP) specimens (PP@AM-18.3) also is investigated using cone calorimeter. Compared with two controlled samples, PP@AM-18.3 shows significantly increased time to ignition, the lowest fire growth index and highest fire performance index. This may give a new flame retarded approach for low SSA polymer materials with little amount flame retardants.

Herein, combined with a pervasive smartphone installed with a color recognition app, dual-responsive CDs@Eu/GMP ICPs were designed as a red-to-blue paper-based colorimetric sensor for the point-of-use analysis of cerebral acetylcholinesterase (AChE) upon Cd2+ exposure. Blue-emitting CDs with multi-functional groups as guests were encapsulated into the network of Eu/GMP ICPs to obtain CDs@Eu/GMP ICPs with the sensitized red fluorescence of Eu3+. With the presence of thiocholine (TCh), derived from acetylthiocholine (ATCh) hydrolyzed by AChE, the coordination environment of the CDs@Eu/GMP ICPs was interrupted, leading to the collapse of the CDs@Eu/GMP ICP network and the corresponding release of guest CDs into the surrounding environment. Consequently, the sensitized red fluorescence of Eu3+ decreased and the blue fluorescence of the CDs increased. This obvious red-to-blue fluorescent color changes of CDs@Eu/GMP ICPs on test paper could then be integrated with the smartphone for point-of-use analysis of cerebral AChE upon Cd2+ exposure, which not only offers a new analytical platform for a better understanding of the environmental risk of Alzheimer's Dementia (AD), but also holds great potential in the early diagnosis of AD even at the asymptomatic stage with the decrease in CSF AChE as an early biomarker.