Search

An investigation was carried out of the effect of various surfactants added during the wet vibrogrinding of zircon on the degree of dispersion of the powder and on the sintering of specimens molded from the powders. When added in proportions up to 0.2% all surfactants tested (naphthenate soap, Asidol, titanium soap, GKZh-94, GKZh-10, triethanolamine, and sugar) helped to reduce the time required to grind the zircon to a given fineness from 15–20 to 4 h, i.e., by a factor of about 2.5–4.

International audience; Abstract:This paper details an extraction procedure to fully model the transient self-heating of transistors from a GaN HEMT technology. Frequency-resolved gate resistance thermometry (f-GRT) is used to extract the thermal impedance of HEMTs with various gate widths. A fully scalable analytical model is developed from the experimental results. In the second stage, transient thermoreflectance imaging (TTI) is used to bring deeper insights into the HEMTs' temperature distribution by individually extracting the transient self-heating of each finger. TTI results are further used to successfully validate the f-GRT results and the modeling of the thermal impedance. Overall, f-GRT is demonstrated to be a fast and robust method for characterizing the transient thermal characteristics of a GaN HEMT. For the first time to the authors' knowledge, a scalable model of the thermal impedance is extracted fully from experimental results.

Under microwave irradiation, raw sludge was pyrolyzed mainly by evaporation of water, with a weight loss ratio of 84.8% and a maximum temperature not exceeding 200 °C. High-temperature pyrolysis of SiC sludge could be realized, with a weight loss ratio of 93.4% and a final pyrolysis temperature of 1131.7 °C. Variations between the electric field intensity distribution are the main reason for the differences of pyrolysis efficiencies. HFSS simulation showed that the electric field intensity of the raw sludge gradually decreased from 2.94 × 10 4 V/m to 0.88 × 10 4 V/m when pyrolysis ends, while that of SiC sludge decreased from 3.73 × 10 4 V/m at the beginning to 1.28 × 10 4 V/m, then increased to 4.03 × 10 4 V/m. The electromagnetic effect is the main factor (r ≥ 0.91) influencing the temperature increase and weight loss of raw sludge. Both the electromagnetic effect and heat conduction effect influenced temperature rise and weight loss of SiC sludge, but the former’s influence was comparatively larger.

Scaling of bulk MOSFET faces great challenges in nanoscale integration technology by producing short channel effect which leads to increased leakage. FinFET has become the most promising substitute to bulk CMOS technology because of reducing short channel effect. Dual-gate FinFET can be designed either by shorting gates on either side for better performance or both gates can be controlled independently to reduce the leakage and hence power consumption. A six transistor SRAM cell based on independent-gate FinFET technology is described in this paper for simultaneously reducing the active and standby mode power consumption. A work is focused on the independent gate FinFET technology as this mode provides less power consumption, less area consumption and low delay as compared to other modes. Leakage current and power consumption in independent gate FinFET is compared with tied gate or shorted gate FinFET SRAM cell. Moreover, delay has been estimated in presented SRAM cells. Further, leakage reduction technique is applied to independent gate FinFET 6T SRAM cell.

International audience; The aim of this work was to analyse the material behaviour of thermally modified and native spruce by load applied perpendicularly to the grain. Therefore, thermally modified and native samples were prepared for bending tests with the load in tangential direction. The bending strength in radial direction decreases significantly with the thermal treatment. The fracture surfaces in the tangential section of the bending samples after testing were analysed with a scanning electron microscope. For native samples, the typical failure was found in the intercellular area. For thermally modified samples, failure of the entire cell wall was observed. The material behaviour is more brittle, as demonstrated by the load-deflection curves, but also by anatomical studies of the fracture surfaces.

(Ba,Ca)(Ti,Zr)O3 solid solutions are promising lead-free piezoelectrics near their polymorphic phase boundary, which is believed to be linked to the interplay between B-site driven ferroelectricity and A-site driven ferroelectricity. Focusing on (Ba,Ca)TiO3, we support this picture from first-principles calculations. In particular, we show how steric effects related to the partial substitution of Ba by Ca largely enhance the Ca-driven ferroelectricity, already virtually allowed in the parent CaTiO3. The emergent interplay between the Ca-driven and Ti-driven mechanisms lowers the energy barrier between different polar states, which eventually results in a quasi-isotropic polarization under substitution of a small concentration of Ba by Ca. A sizeable enhancement of the piezoelectric response directly results from these features.(Ba,Ca)(Ti,Zr)O3 solid solutions are promising lead-free piezoelectrics near their polymorphic phase boundary, which is believed to be linked to the interplay between B-site driven ferroelectricity and A-site driven ferroelectricity. Focusing on (Ba,Ca)TiO3, we support this picture from first-principles calculations. In particular, we show how steric effects related to the partial substitution of Ba by Ca largely enhance the Ca-driven ferroelectricity, already virtually allowed in the parent CaTiO3. The emergent interplay between the Ca-driven and Ti-driven mechanisms lowers the energy barrier between different polar states, which eventually results in a quasi-isotropic polarization under substitution of a small concentration of Ba by Ca. A sizeable enhancement of the piezoelectric response directly results from these features.