Search

The merit of deacetylation of corn stover prior to pretreatment is decreasing the formation of inhibitors and improving enzyme hydrolysis, proved in dilute acid pretreatment. However, few studies are done on how deacetylation would affect bioconversion process containing steam explosion. In this study, the effect of deacetylation on steam explosion was conducted using poplar as substrate. About 57 to 90% of acetyl group in poplar, depending on alkaline types and concentration, was removed by dilute alkaline deacetylation in 6 h. Deacetylation eliminated over 85% of inhibitor formation during downstream steam explosion. However, deacetylation prior to steam explosion decreased the dissolution of hemicellulose, thus reducing the cellulose accessibility of pretreated poplar, finally resulting in 5-20% decrease in glucose yield and 20-35% decrease in xylose yield. The addition of 5% SO 2 during steam explosion significantly improved the hydrolysis of deacetylated and pretreated poplar without significantly increasing the concentration of inhibitors. Incorporating 45 mmol/kg sulfoacid group in lignin fraction of deacetylated and then pretreated poplar dramatically improved the xylose yield to about 100% and increased the glucose yield by 30%.

Accurate protein quantification is necessary in many of the steps during the enzymatic hydrolysis of pretreated lignocellulosic biomass, from the fundamental determination of enzyme kinetics to techno-economic assessments, such as the use of enzyme recycling strategies, evaluation of enzyme costs, and the optimization of various process steps. In the work described here, a modified, more rapid ninhydrin-based protein quantification assay was developed to better quantify enzyme levels in the presence of lignocellulosic biomass derived compounds. The addition of sodium borohydride followed by acid hydrolysis at 130 °C greatly reduced interference from monosaccharides and oligosaccharides and decreased the assay time 6-fold. The modified ninhydrin assay was shown to be more accurate as compared to various traditional colorimetric protein assays when commercial cellulase enzyme mixtures were quantified under typical pretreated lignocellulosic biomass enzymatic hydrolysis conditions. The relatively short assay time and microplate-reading capability of the modified assay indicated that the method could likely be used for high-throughput protein determination.

Sweet sorghum bagasse (SSB) was steam pretreated in the conditions of 190 °C for 5 min to assess its amenability to the pretreatment and enzymatic hydrolysis. Results showed that pretreatment conditions were robust enough to pretreat SSB with maximum of 87% glucan and 72% xylan recovery. Subsequent enzymatic hydrolysis showed that the pretreated SSB at 2% substrate consistency resulted in maximum of 70% glucan-glucose conversion. Increasing substrate consistency from 2% to 16% led to a significant reduction in glucan conversion. However, the decrease ratio of glucan-glucose conversion was the minimum when the consistency increased from 2% to 12%. When the pretreated SSB consistency of 12% was applied for hydrolysis, increase in cellulase loading from 7.5 up to 20 filter paper units (FPU)/g glucan resulted only in 14% increase in glucan-glucose conversion compared to 20% increase with cellulase loading varying from 2.5 to 7.5 FPU/g glucan. More than 10 cellobiase units (CBU)/g glucan β-glucosidase supplementation had no noticeable improvement on glucan-glucose conversion. Additionally, supplementation of xylanase was found to significantly increase glucan-glucose conversion from 50% to 80% with the substrate consistency of 12%, when the cellulase and β-glucosidase loadings were at relatively low enzyme loadings (7.5 FPU/g and 10 CBU/g glucan). It appeared that residual xylan played a critical role in hindering the ease of hydrolysis of SSB. A proper xylanase addition was suggested to achieve a high hydrolysis yield at relatively high substrate consistency with relatively low enzyme loadings.

The amount of sawmill residue available in Canada to support the emerging cellulosic ethanol industry was examined. A material flow analysis technique was employed to determine the amount of sawmill residue that could possibly be available to the ethanol industry per annum. A combination of two key trends--improved efficiency of lumber recovery and increased uptake of sawmill residues for self-generation and for wood pellet production--have contributed to a declining trend of sawmill residue availability. Approximately 2.3 x 10⁶ bone-dry tons per year of sawmill residue was estimated to be potentially available to the cellulosic ethanol industry in Canada, yielding 350 million liters per year of cellulosic ethanol using best practices. An additional 2.7 billion liters of cellulosic ethanol might be generated from sawmill residue that is currently used for competing wood energy purposes, including wood pellet generation. Continued competition between bioenergy options will reduce the industrial sustainability of the forest industry. Recommendations for policy reforms towards improved industrial sustainability practices are provided.

Mountain pine beetle-killed lodgepole pine (Pinus contorta) chips were pretreated using the organosolv process, and their ease of subsequent enzymatic hydrolysis was assessed. The effect of varying pretreatment chemicals and solvents on the substrate's physicochemical characteristics was also investigated. The chemicals employed were MgCl2, H2SO4, SO2, and NaOH, and the solvents were ethanol and butanol. It was apparent that the different pretreatments resulted in variations in both the chemical composition of the solid and liquid fractions as well in the extent of cellulolytic hydrolysis (ranging from 21% to 82% hydrolysis after 12 h). Pretreatment under acidic conditions resulted in substrates that were readily hydrolyzed despite the apparent contradiction that pretreatment under alkaline conditions resulted in increased delignification (approximately 7% and 10% residual lignin for alkaline conditions versus 17% to 19% for acidic conditions). Acidic pretreatments also resulted in lower cellulose degree of polymerization, shorter fiber lengths, and increased substrate porosity. The substrates generated when butanol/water mixtures were used as the pretreatment solvent were also hydrolyzed more readily than those generated with ethanol/water. This was likely due to the limited miscibility of the solvents resulting in an increased concentration of pretreatment chemicals in the aqueous layer and thus a higher pretreatment severity.

The potential economic benefits of surfactants addition on enzymatic hydrolysis of steam-exploded lodgepole pine (SELP) and ethanol-pretreated lodgepole pine (EPLP) were investigated in this study. Free cellulase readsorption on fresh substrate was used to recover and recycle cellulase enzymes during the hydrolysis of SELP and EPLP substrate. Supplementing Tween 80 during the hydrolysis could facilitate enzyme recycling for EPLP substrate. A logarithmic correlation was established between surfactant concentration and free cellulase content after lignocellulosic hydrolysis, which was used to compute enzyme cost savings over various Tween 80 concentrations. A simple economic analysis of enzyme cost savings versus the cost of surfactant was undertaken. The results indicated that the addition of Tween 80 (priced at US $0.25/kg) during the hydrolysis of the EPLP substrate could save 60% of the total enzyme cost at concentrations in the 0.025% to 0.2% range. The addition of Tween for the hydrolysis of the SELP substrate significantly reduced the material cost by 24% per 1 gal of ethanol produced, and the ethanol production cost could be reduced by 8.6% with the addition of Tween and enzymes recycle for the hydrolysis of SELP substrate. A schematic concept of recycling enzyme and surfactant was also presented with a recirculation of process streams during hydrolysis. Further analysis indicated a 66% reduction in total enzyme cost could potentially be achieved under the concept.

Hybrid poplar (Populus nigra x P. maximowiczii) chips were pretreated using an organosolv ethanol process. The effect of pretreatment conditions (temperature, time, catalyst, and ethanol concentration) on the substrate characteristics, including fiber size, crystallinity, and degree of polymerization of cellulose, was investigated using an experimental matrix designed with response surface methodology. The conditions ranged 155-205 degrees C, 26-94 min, 0.83-1.67% catalyst (H(2)SO(4)) on oven-dry wood chip (w/w), and 25-75% ethanol concentration (v/v). The results indicated that the substrate characteristics are controllable and predictable. Desirable substrates can be prepared by fine-tuning the processing parameters. The regression models developed, allowed the quantitative prediction of the substrate characteristics from the pretreatment conditions used.

Seven cellulase preparations from Penicillium and Trichoderma spp. were evaluated for their ability to hydrolyze the cellulose fraction of hardwoods (yellow poplar and red maple) pretreated by organosolv extraction, as well as model cellulosic substrates such as filter paper. There was no significant correlation among hydrolytic performance on pretreated hardwood, based on glucose release, and filter paper activity. However, performance on pretreated hardwood showed significant correlations to the levels of endogenous beta-glucosidase and xylanase activities in the cellulase preparation. Accordingly, differences in performance were reduced or eliminated following supplementation with a crude beta-glucosidase preparation containing both activities. These results complement a previous investigation using softwoods pretreated by either organosolv extraction or steam explosion. Cellulase preparations that performed best on hardwood also showed superior performance on the softwood substrates.

A lignocellulosic-based biorefining strategy may be supported by biomass reserves, created initially with residues from wood product processing or agriculture. Biomass reserves might be expanded using innovative management techniques that reduce vulnerability of feedstock in the forest products or agricultural supply chain. Forest-harvest residue removal, disturbance isolation, and precommercial thinnings might produce 20-33 x 10(6) mt/yr of feedstock for Canadian biorefineries. Energy plantations on marginal Canadian farmland might produce another 9-20 mt. Biomass reserves should be used to support first-generation biorefining installations for bioethanol production, development of which will lead to the creation of future high-value coproducts. Suggestions for Canadian policy reform to support biomass reserves are provided.

Softwoods are generally considered to be one of the most difficult lignocellulosic feedstocks to hydrolyze to sugars for fermentation, primarily owing to the nature and amount of lignin. If the inhibitory effect of lignin can be significantly reduced, softwoods may become a more useful feedstock for the bioconversion processes. Moreover, strategies developed to reduce problems with softwood lignin may also provide a means to enhance the processing of other lignocellulosic substrates. The Forest Products Biotechnology Group at the University of British Columbia has been developing softwood-to-ethanol processes with SO2-catalyzed steam explosion and ethanol organosolv pretreatments. Lignin from the steam explosion process has relatively low reactivity and, consequently, low product value, compared with the high-value coproduct that can be obtained through organosolv. The technical and economic challenges of both processes are presented, together with suggestions for future process development.

The biorefinery is a key concept used in the strategies and visions of many industrial countries. The potential for Canadian biorefineries based on lignocellulosic forest and agricultural residues is examined. The sector is described in terms of research interests, emerging companies, and established corporate interests. It is found that the Canadian biorefining sector currently has an emphasis on specific bioproduct generation, and the process elements required for a true sugar-based process are in the research phase. A Canadian national strategy should focus on increasing forest industry participation, and increasing collaboration with the provinces, particularly in western Canada.

Pretreatment of Douglas-fir by steam explosion produces a substrate containing approx 43% lignin. Two strategies were investigated for reducing the effect of this residual lignin on enzymatic hydrolysis of cellulose: mild alkali extraction and protein addition. Extraction with cold 1% NaOH reduced the lignin content by only approx 7%, but cellulose to glucose conversion was enhanced by about 30%. Before alkali extraction, addition of exogenous protein resulted in a significant improvement in cellulose hydrolysis, but this protein effect was substantially diminished after alkali treatment. Lignin appears to reduce cellulose hydrolysis by two distinct mechanisms: by forming a physical barrier that prevents enzyme access and by non-productively binding cellulolytic enzymes. Cold alkali appears to selectively remove a fraction of lignin from steam-exploded Douglas-fir with high affinity for protein. Corresponding data for mixed softwood pretreated by organosolv extraction indicates that the relative importance of the two mechanisms by which residual lignin affects hydrolysis is different according to the pre- and post-treatment method used.

Good enzymatic hydrolysis of steam-exploded Douglas fir wood (SEDW) cannot be achieved owing to the very high lignin content ( >40%) that remains associated with this substrate. Thus, in this study, we investigated the use of alkali-oxygen treatment as a posttreatment to delignify SEDW and also considered the enzymatic hydrolyzability of the delignified SEDW. The results showed that under optimized conditions of 15% NaOH, 5% consistency, 110 degrees C, and 3 h, approx 84% of the lignin in SEDW could be removed. The resulting delignified SEDW had good hydrolyzability, and cellulose-to-glucose conversion yields of over 90 and 100% could be achieved within 48 h with 20 and 40 filter paper units/g of cellulose enzyme loadings, respectively. It was also indicated that severe conditions, such as high NaOH concentration and high temperature, should not be utilized in oxygen delignification of SEDW in order to avoid extensive condensation of lignin and significant degradation of cellulose.

A quantitative approach was taken to determine the inhibition effects of glucose and other sugar monomers during cellulase and beta-Glucosidase hydrolysis of two types of cellulosic material: Avicel and acetic acid-pretreated softwood. The increased glucose content in the hydrolysate resulted in a dramatic increase in the degrees of inhibition on both beta-Glucosidase and cellulase activities. Supplementation of mannose, xylose, and galactose during cellobiose hydrolysis did not show any inhibitory effects on beta-Glucosidase activity. However, these sugars were shown to have significant inhibitory effects on cellulase activity during cellulose hydrolysis. Our study suggests that high-substrate consistency hydrolysis with supplementation of hemicellulose is likely to be a practical solution to minimizing end-product inhibition effects while producing hydrolysate with high glucose concentration.

A batch reactor was employed to steam explode corn fiber at various degrees of severity to evaluate the potential of using this feedstock as part of an enzymatically mediated cellulose-to-ethanol process. Severity was controlled by altering temperature (150-230 degrees C), residence time (1-9 min), and SO2 concentration (0-6% [w/w] dry matter). The effects of varying the different parameters were assessed by response surface modeling. The results indicated that maximum sugar yields (hemicellulose-derived water soluble, and cellulose-derived following enzymatic hydrolysis) were recovered from corn fiber pretreated at 190 degrees C for 5 minutes after exposure to 3% SO2. Sequential SO2-catalyzed steam explosion and enzymatic hydrolysis resulted in a conversion efficiency of 81% of the combined original hemicellulose and cellulose in the corn fiber to monomeric sugars. An additional posthydrolysis step performed on water soluble hemicellulose stream increased the concentration of sugars available for fermentation by 10%, resulting in the high conversion efficiency of 91%. Saccharomyces cerevisiae was able to ferment the resultant corn fiber hydrolysates, perhydrolysate, and liquid fraction from the posthydrolysis steps to 89, 94, and 85% of theoretical ethanol conversion, respectively. It was apparent that all of the parameters investigated during the steam explosion pretreatment had a significant effect on sugar recovery, inhibitory formation, enzymatic conversion efficiency, and fermentation capacity of the yeast.

The impetus for this paper is Canada's commitment under the United Nations Framework Convention on Climate Change to reduce national greenhouse gas emissions as well as reducing our dependency on fossil fuels. Wood-based ethanol offers an excellent opportunity for greenhouse gas mitigation due to market potential, an ability to offset significant emissions from the transportation sector, a reduction of emissions from CO2-intensive waste-management systems, and carbon sequestration in afforested plantations. While there are technological and economic barriers to overcome, using wood-biomass as a source of ethanol can be an economically viable tool for reducing greenhouse gas levels in the atmosphere. This paper examines the costs and mitigation potential of the production of ethanol from biomass supplied from industrial wood waste as well as from trees harvested from afforested land.

Corn fiber, a by-product of the corn wet-milling industry, represents a renewable resource that is readily available in significant quantities and could potentially serve as a low-cost feedstock for the production of fuel-grade alcohol. In this study, we used a batch reactor to steam explode corn fiber at various degrees of severity to evaluate the potential of using this feedstock in the bioconversion process. The results indicated that maximum sugar yields (soluble and following enzymatic hydrolysis) were recovered from corn fiber that was pretreated at 190 degrees C for 5 min with 6% SO2. Sequential SO2-catalyzed steam explosion and enzymatic hydrolysis resulted in very high conversion (81%) of all polysaccharides in the corn fiber to monomeric sugars. Subsequently, Saccharomyces cerevisiae was able to convert the resultant corn fiber hydrolysates to ethanol very efficiently, yielding 90-96% of theoretical conversion during the fermentation process.

In an attempt to elucidate the effect of reduced mixing on the enzymatic hydrolysis of lignocellulosic feedstocks, a pretreated softwood substrate was hydrolyzed under various mixing regimes using a commercial cellulase mixture. The substrate was generated by SO2-catalyzed steam explosion of Douglas fir wood chips followed by alkali-peroxide treatment to remove lignin. Three mixing regimes were tested; continuous mixing at low (25 rpm) and high (150 rpm) speeds, and mixing at low-speed interspersed with 5-min intervals of high-speed agitation at 150 rpm. At both substrate concentrations (7.5 and 10% [w/w]), the mixed-speed mixing was able to produce sufficiently high conversion rates and yields (93% after 96 h), close or slightly better than those obtained under vigorous mixing (150 rpm). The low-speed shaking produced appreciably lower conversion yields at both levels of substrate concentration. Therefore, the mixed-speed regime may be a viable process option, because it does not seem to have an adverse impact on the cellulose conversion yield and can be an effective means of reducing the mixing energy requirements of an enzymatic hydrolysis process.

The sugar yield and enzyme adsorption profile obtained during the hydrolysis of SO2-catalyzed steam-exploded Douglas-fir and posttreated steam-exploded Douglas-fir substrates were determined. After hot alkali peroxide posttreatment, the rates and yield of hydrolysis attained from the posttreated Douglas-fir were significantly higher, even at lower enzyme loadings, than those obtained with the corresponding steam-exploded Douglas-fir. The enzymatic adsorption profiles observed during hydrolysis of the two substrates were significantly different. Ultrafiltration was employed to recover enzyme in solution (supernatant) and reused in subsequent hydrolysis reactions with added, fresh substrate. These recycle findings suggested that the enzyme remained relatively active for three rounds of recycle. It is likely that enzyme recovery and reuse during the hydrolysis of posttreated softwood substrates could lead to reductions in the need for the addition of fresh enzyme during softwood-based bioconversion processes.

One of the limiting factors restricting the effective and efficient bioconversion of softwood-derived lignocellulosic residues is the recalcitrance of the substrate following pretreatment. Consequently, the ensuing enzymatic process requires relatively high enzyme loadings to produce monomeric carbohydrates that are readily fermentable by ethanologenic microorganisms. In an attempt to circumvent the need for larger enzyme loadings, a simultaneous physical and enzymatic hydrolysis treatment was evaluated. A ball-mill reactor was used as the digestion vessel, and the extent and rate of hydrolysis were monitored. Concurrently, enzyme adsorption profiles and the rate of conversion during the course of hydrolysis were monitored. alpha-Cellulose, employed as a model substrate, and SO2-impregnated steam-exploded Douglas-fir wood chips were assessed as the cellulosic substrates. The softwood-derived substrate was further posttreated with water and hot alkaline hydrogen peroxide to remove >90% of the original lignin. Experiments at different reaction conditions were evaluated, including substrate concentration, enzyme loading, reaction volumes, and number of ball beads employed during mechanical milling. It was apparent that the best conditions for the enzymatic hydrolysis of alpha-cellulose were attained using a higher number of beads, while the presence of air-liquid interface did not seem to affect the rate of saccharification. Similarly, when employing the lignocellulosic substrate, up to 100% hydrolysis could be achieved with a minimum enzyme loading (10 filter paper units/g of cellulose), at lower substrate concentrations and with a greater number of reaction beads during milling. It was apparent that the combined strategy of simultaneous ball milling and enzymatic hydrolysis could improve the rate of saccharification and/or reduce the enzyme loading required to attain total hydrolysis of the carbohydrate moieties.

Douglas-fir sapwood and heartwood were impregnated with SO2 and steam exploded at three severity levels, and the cellulose-rich, water-insoluble component was enzymatically hydrolyzed. The high-severity conditions resulted in near complete solubilization and some degradation of hemicelluloses and a significant improvement in the efficiency of enzymatic digestibility of the cellulose component. At lower severity, some of the hemicellulose remained unhydrolyzed, and the cellulose present in the pretreated solids was not readily hydrolyzed. The medium-severity pretreatment conditions proved to be a good compromise because they improved the enzymatic hydrolyzability of the solids and resulted in the recovery of the majority of hemicellulose in a monomeric form within the water-soluble stream. Sapwood-derived wood chips exhibited a higher susceptibility to both pretreatment and hydrolysis and, on steam explosion, formed smaller particles as compared to heartwood-derived wood chips.

Effective utilization of the lignin by-product is a prerequisite to the commercial viability of ethanol production from softwood wastes using a steam explosion (SE)/enzymatic hydrolysis (EH)/fermentation process. Changes in the chemical composition of Douglas fir wood on SO2-catalyzed SE followed by EH were assessed using conventional analytical methods and new halogen-probe techniques. A significant solubilization of hemicelluloses was observed in the SE stage, the severity of which affected subsequent fermentation of cellulose and sorption of enzymes. SE of softwood resulted in dramatic changes in the chemical structure of lignin in the residual material involving chemical reactions via the benzyl cation. This leads to a more condensed lignin with partly blocked alpha-reaction centres. Possible uses for this lignin are discussed.

Techno-economic modeling has been a valuable tool in directing and assessing the research and development efforts for biomass-to-ethanol processes. In developing a techno-economic model of a "generic" wood-to-ethanol process, we decided to follow a three-pronged design approach. This initially consisted of a detailed review of the current definition and technical maturity of the process, which concluded that the process remains complex and immature. More recently, we have critically assessed/compared two inherited models, and examined the historical and current trends in modeling design. We confirmed that process complexity and immaturity, in association with the capabilities of the available modeling tools and the ease with which they can be used, influenced the design and implementation of past models. We have discussed these influences with reference to our own model development decisions. For example, on review of two inherited techno-economic models, we decided that our new model would require a greater degree of flexibility in its structure and user interface.

Thielavia terrestris 255B, a thermophilic ascomycete, produced two major forms of xylanase with pIs of 4.6 (xylanase I) and 6.1 (xylanase II). The latter enzyme could be purified to greater than 99% homogeneity using anion-exchange chromatography and gel filtration. Xylanase II had a mol wt of 25.7 kDa (SDS-PAGE) and a pH and a temperature optimum of 3.6-4.0 and 60-65 degrees C, respectively. The ratio of the enzyme's activity against xylan and carboxymethylcellulose was 500-1000 to 1, indicating a possible application of this enzyme in biobleaching processes. The amino acid sequence of this protein is being determined, and initial data suggest that the enzyme belongs to a group of low-mol wt xylanases that have been isolated from both bacteria and fungi.