Search

Multiple protocols have been reported to fabricate paper-based analytical devices (PADs). However, some of these techniques must be revised because of the instrumentation required. This paper describes a versatile and globally affordable method to fabricate PADs using office paper as a substrate and a laser printing technique to define hydrophobic barriers on paper surfaces. To demonstrate the feasibility of the alternatives proposed in this study, the fabrication of devices for three types of detection commonly associated with using PADs was demonstrated: colorimetric detection, electrochemical detection, and mass spectrometry associated with a paper-spray ionization (PSI-MS) technique. Besides that, an evaluation of the type of paper used and chemical modifications required on the substrate surface are also presented in this report. Overall, the developed protocol was suitable for using office paper as a substrate, and the laser printing technique as an efficient fabrication method when using this substrate is accessible at a resource-limited point-of-need. Target analytes were used as a proof of concept for these detection techniques. Colorimetric detection was carried out for acetaminophen, iron, nitrate, and nitrite with limits of detection of 0.04 μg, 4.5 mg mL−1, 2.7 μmol L−1, and 6.8 μmol L−1, respectively. A limit of detection of 0.048 fg mL−1 was obtained for the electrochemical analysis of prostate-specific antigen. Colorimetric and electrochemical devices revealed satisfactory performance when office paper with a grammage of 90 g m−2 was employed. Methyldopa analysis was also carried out using PSI-MS, which showed a good response in the same paper weight and behavior compared to chromatographic paper. [ABSTRACT FROM AUTHOR]

This report presents an investigation into the use of carbon paper electrodes prepared from chitosan-adhered graphene magnetite nanoparticles for the analysis of Cr(VI). The preparation and storage of carbon paper electrodes is a simple process, and these electrodes are easier to replace than electrodes modified by more conventional methods. The electrochemical detection of Cr(VI) using square wave adsorption cathodic dissolution voltammetry (SWAdCSV) with high selectivity and sensitivity, as well as the optimum conditions for the preparation of the electrodes and the electrode parameters affecting the SWAdCSV signal, were the main points of focus of the investigation. Cr(VI) was detected linearly in the range of 4-40 μg L-1 with a detection limit of 2.84 μg L-1. The electrode output precision, calculated as %RSD, was 7.16% (n = 6), and this was the measurement used for the detection of Cr(VI) in standard and test samples with recoveries between 89% and 114%. The results were consistent with those obtained using the standard UV-Vis spectrophotometric method with a paired t-test at 95% confidence level. [ABSTRACT FROM AUTHOR]

Non-enzymatic electrochemical blood glucose sensors often suffer from issues such as requiring an alkaline environment, limited monitoring range, and poor anti-interference properties. Carbon substrates have been demonstrated to improve the performance of non-enzymatic sensors, but complex and energy-consuming manufacturing processes restrict their use. Herein, a simple and green approach for the preparation of 3D porous Au/Au-Pt networks (PAAPNs) is proposed using tissue paper for recycling as the nanomaterial substrate to deposit Au-Pt bimetallic nanoparticles. The unique structure of the PAAPNs sensor allows for low-potential operation (-1.0 V) with a wide monitoring range (-0.25 to 36 mM) in a neutral environment. Moreover, the sensor exhibited excellent selectivity (<10% response of interference) even without the use of an anti-interference outer membrane. Further investigation using density functional theory (DFT) simulation revealed the synergistic effect between Au and Pt in promoting glucose oxidation. Overall, this work provides a simple and low-carbon footprint method for creating carbon substrates from tissue paper for recycling, offering new opportunities for fabricating novel value-added nanomaterials for medical sensing applications. [ABSTRACT FROM AUTHOR]

Paper-based ratiometric fluorescence sensors are normally prepared using two or more types of fluorescent materials on a paper chip for simple, low-cost and fast detection. However, the choice of multi-step and one-step modifications on the paper chip affects the analytical performance. Herein, a novel paper-based dual-emission ratiometric fluorescence sensor was designed for the selective detection of tetracycline (TC). Carbon dots (CDs) modified with Eu3+ were combined with a sealed paper-based microfluidic chip by two methods: one-step grafting of CDs-Eu3+ on paper and step-by-step grafting of CDs and Eu3+ on paper. The analytical performance was studied and optimized respectively. The red fluorescence of Eu3+ at 450 nm is enhanced and the blue fluorescence of CDs at 617 nm is quenched by energy transfer in the presence of TC. Under optimal conditions, TC is selectively determined in the linear range from 0.1 μM to 100 μM with a detection limit of 0.03 μM by the step-by-step grafting method. In addition, the sealed paper chip could effectively prevent pollution and volatilization from the reagent. This technique has been used to analyze TC in seafood aquaculture water with satisfactory results. [ABSTRACT FROM AUTHOR]

Selective enrichment of La(III) by green material as an industrial raw material is of great research interest. In this study, the selective interaction between P and La(III) was utilized, and waste paper (WP) modified with phytic acid (PA) was used to adsorb La(III) from water using a simple one-pot method. The adsorption capacity was 237.23 mg g−1 (30 °C, pH = 5, initial concentration of 200 mg L−1). The equilibrium isotherm fitted the Langmuir isotherm model well. The adsorption equilibrium was reached after 15 min. The adsorption kinetics followed the pseudo-second-order kinetic model, indicating that the adsorption mechanism of the material towards La(III) is single-layer chemisorption. It selectively adsorbed La(III) from four coexisting substances (Pb, Ni, Cu, and Co). After six cycles, the adsorption efficiency of the adsorbent material remained at 60%. [ABSTRACT FROM AUTHOR]

This paper reports a spin-disc paper-based device with 10 individual detection units containing electromagnetic modules controlling the sample incubation time before chemiluminescence (CL) signal detection. After the sample was added to the top paper chip and incubated with the enzyme, the electromagnet was turned off to allow contact between the top and bottom paper. The H2O2 generated by the sample flowed vertically to the bottom paper and initiated the oxidase of the luminol to generate the CL signal. After one detection the disc was automatically rotated to the next position to repeat the above detection. The advantage of using the device over the lateral flow and the in situ detection was firstly proved using the detection of H2O2 and the glucose/lactate sample with 5 minute incubation. The CL intensity was increased 300 times/1000 times as the glucose/lactate was incubated for 5 minutes compared to the non-incubated samples. Afterward, the device was employed to separately detect glucose and lactate diluted in PBS, artificial sweat, artificial saliva, and fresh cell culture media. Finally, the device was employed to detect the glucose and lactate in the media collected over the 24 hour culture of PC3 cells. The uptake and production rates of glucose and lactate were correspondingly determined as 0.328 ± 0.015 pmol h−1 per cell and 1.254 ± 0.053 pmol h−1 per cell, respectively. The reported device has wide application potential due to its capabilities in automatic detection of multiple samples with very high sensitivity and small sample volume (down to 0.5 μL). [ABSTRACT FROM AUTHOR]

Developing a fluidic platform that combines high-throughput with reconfigurability is essential for a wide range of cutting-edge applications, but achieving both capabilities simultaneously remains a significant challenge. Herein, we propose a novel and unique method for droplet manipulation via drawing surface charge graphics on electrode-free papers in a contactless way. We find that opposite charge graphics can be written and retained on the surface layer of porous insulating paper by a controlled charge depositing method. The retained charge graphics result in high-resolution patterning of electrostatic potential wells (EPWs) on the hydrophobic porous surface, allowing for digital and high-throughput droplet handling. Since the charge graphics can be written/projected dynamically and simultaneously in large areas, allowing for on-demand and real-time reconfiguration of EPWs, we are able to develop a charge-graphic fluidic platform with both high reconfigurability and high throughput. The advantages and application potential of the platform have been demonstrated in chemical detection and dynamically controllable fluidic networks. [ABSTRACT FROM AUTHOR]

Fast detection of contaminants of emerging concern (CECs) in water resources is of great environmental interest. Ideally, sustainable materials should be used in water quality monitoring technologies implemented for such purposes. In this regard, the application of bio-based materials aimed at the fabrication of analytical platforms has become of great importance. This research merges both endeavors by exploring the application of chitosan-coated paper, decorated with silver nanoparticles (AgNPs), on surface-enhanced Raman scattering (SERS) spectroscopy studies of two distinct types of CECs dissolved in aqueous samples: an antibiotic (ciprofloxacin) and a pesticide (thiram). Our results indicate the superior SERS performance of biocoated substrates compared to their non-coated paper counterparts. The detection limits achieved for thiram and ciprofloxacin using the biocoated substrates were 0.024 ppm and 7.7 ppm, respectively. The efficient detection of both analytes is interpreted in terms of the role of the biopolymer in promoting AgNPs assemblies that result in local regions of enhanced SERS activity. Taking advantage of these observations, we use confocal Raman microscopy to obtain Raman images of the substrates using ciprofloxacin and thiram as molecular probes. We also demonstrate that these biobased substrates can be promising for on-site analysis when used in conjunction with portable Raman instruments. [ABSTRACT FROM AUTHOR]

Safe, accurate, and reliable analysis of urinary biomarkers is clinically important for early detection and monitoring of the progression of chronic kidney disease (CKD), as it has become one of the world's most prevalent non-communicable diseases. However, current technologies for measuring urinary biomarkers are either time-consuming and limited to well-equipped hospitals or lack the necessary sensitivity for quantitative analysis and post a health risk to frontline practitioners. Here we report a robust paper-based dual functional biosensor, which is integrated with the clinical urine sampling vial, for the simultaneous and quantitative analysis of pH and glucose in urine. The pH sensor was fabricated by electrochemically depositing IrOx onto a paper substrate using optimised parameters, which enabled an ultrahigh sensitivity of 71.58 mV pH -1 . Glucose oxidase (GOx) was used in combination with an electrochemically deposited Prussian blue layer for the detection of glucose, and its performance was enhanced by gold nanoparticles (AuNPs), chitosan, and graphite composites, achieving a sensitivity of 1.5 μA mM -1 . This dual function biosensor was validated using clinical urine samples, where a correlation coefficient of 0.96 for pH and 0.98 for glucose detection was achieved with commercial methods as references. More importantly, the urine sampling vial was kept sealed throughout the sample-to-result process, which minimised the health risk to frontline practitioners and simplified the diagnostic procedures. This diagnostic platform, therefore, holds high promise as a rapid, accurate, safe, and user-friendly point-of-care (POC) technology for the analysis of urinary biomarkers in frontline clinical settings.

The regular and on-site monitoring of ions in drinking water is essential for safeguarding public health, ensuring high water quality, and preserving the ecological balance of aquatic ecosystems. Thus, developing a portable analytical device for the rapid, cost-effective, and visual on-site detection of multiple environmental pollutants is notably significant. In the present work, a novel ratiometric microfluidic paper-based analytical device (μPAD) was designed and developed for the simultaneous detection of Fe 3+ and Cu 2+ ions in water samples taking advantages from built-in masking zone. The μPAD was functionalized with a greenish-yellow fluorescent Zn-based metal-organic framework@tetracycline (FMOF-5@TC) nanocomposite, and the ratiometric design was based on the change in emission color from greenish yellow (FMOF-5@TC) to blue (FMOF-5). The μPAD consisted of one sample zone linked to two detection zones via two channels: the first channel was for the detection of both ions, while the second was intended for detecting only Cu 2+ ions and comprised a built-in masking zone to remove Fe 3+ ions prior to reaching the detection zone. The corresponding color changes were recorded with the aid of a smartphone and RGB calculations. The linear ranges were 0.1-80 μM for Cu 2+ and 0.2-160 μM for Fe 3+ , with limits of detection of 0.027 and 0.019 μM, respectively. The simple μPAD design enabled the simultaneous detection of Cu 2+ and Fe 3+ ions in drinking water samples with excellent accuracy and precision, with spike recoveries of 81.28-96.36% and 83.01-102.33% for Cu 2+ and Fe 3+ , respectively.

This article introduces distance-based paper analytical devices (dPADs) integrated with molecularly imprinted polymers (MIPs) and carbon dots (CDs) for simultaneous quantification of cytokine biomarkers, namely C-reactive protein (CRP), tumor necrosis factor-alpha (TNF-α), and interleukin-6 (IL-6) in human biological samples for diagnosis of cytokine syndrome. Using fluorescent CDs and MIP technology, the dPAD exhibits high selectivity and sensitivity. Detection is based on fluorescence quenching of CDs achieved through the interaction of the target analytes with the MIP layer on the paper substrate. Quantitative analysis is easily accomplished by measuring the distance length of quenched fluorescence with a traditional ruler and naked eye readout enabling rapid diagnosis of cytokine syndrome and the underlying infection. Our sensor demonstrated linear ranges of 2.50-24.0 pg mL -1 ( R 2 = 0.9974), 0.25-3.20 pg mL -1 ( R 2 = 0.9985), and 1.50-16.0 pg mL -1 ( R 2 = 0.9966) with detection limits (LODs) of 2.50, 0.25, and 1.50 pg mL -1 for CRP, TNF-α, and IL-6, respectively. This sensor also demonstrated remarkable selectivity compared to a sensor employing a non-imprinted polymer (NIP), and precision with the highest relative standard deviation (RSD) of 5.14%. The sensor is more accessible compared to prior methods relying on expensive reagents and instruments and complex fabrication methods. Furthermore, the assay provided notable accuracy for monitoring these biomarkers in various human samples with recovery percentages ranging between 99.22% and 103.58%. By integrating microfluidic systems, nanosensing, and MIPs technology, our developed dPADs hold significant potential as a cost-effective and user-friendly analytical method for point-of-care diagnostics (POC) of cytokine-related disorders. This concept can be further extended to developing diagnostic devices for other biomarkers.

A new method utilizing fluorescent ratiometry is proposed for detecting putrescine and spermidine. The method involves the use of a fluorescent probe comprising a 2D halide perovskite synthesized from octadecylamine-iodine and PbI 2 via a grinding-sonicating technique, along with a Eu 3+ -complex. Upon excitation at 290 nm, the probe fluoresces at two distinguishable wavelengths. The addition of putrescine and spermidine significantly decreases the emission of the 2D halide perovskite at 496 nm, while the emission of the Eu 3+ -complex at 618 nm remains stable. The color changes of the probe depend on the concentration of putrescine and spermidine, and the assay offers linearity over a wide concentration range (30-4000 ng mL -1 ), a low detection limit (4 ng mL -1 for spermidine), and a quick response time. Furthermore, a portable device based on a smartphone can be used to record the color change of the paper test strip using the prepared fluorescent materials. The fluorescence quenching mechanism of the probe is explained as dynamic quenching.-1 for spermidine), and a quick response time. Furthermore, a portable device based on a smartphone can be used to record the color change of the paper test strip using the prepared fluorescent materials. The fluorescence quenching mechanism of the probe is explained as dynamic quenching.

Paper-based electrochemical sensors have the characteristics of flexibility, biocompatibility, environmental protection, low cost, wide availability, and hydropathy, which make them very suitable for the development and application of biological detection. This work proposes electrospun cellulose acetate nanofiber (CA NF)-decorated paper-based screen-printed (PBSP) electrode electrochemical sensors. The CA NFs were directly collected on the PBSP electrode through an electrospinning technique at an optimized voltage of 16 kV for 10 min. The sensor was functionalized with different bio-sensitive materials for detecting different targets, and its sensing capability was evaluated by CV, DPV, and chronoamperometry methods. The test results demonstrated that the CA NFs enhanced the detection sensitivity of the PBSP electrode, and the sensor showed good stability, repeatability, and specificity ( p < 0.01, N = 3). The electrochemical sensing of the CA NF-decorated PBSP electrode exhibited a short detection duration of ∼5-7 min and detection ranges of 1 nmol mL -1 -100 μmol mL -1 , 100 fg mL -1 -10 μg mL -1 , and 1.5 × 10 2 -10 6 CFU mL -1 and limits of detection of 0.71 nmol mL -1 , 89.1 fg mL -1 , and 30 CFU mL -1 for glucose, Ag85B protein, and E. coli O157:H7 , respectively. These CA NF-decorated PBSP sensors can be used as a general electrochemical tool to detect, for example, organic substances, proteins, and bacteria, which are expected to achieve point-of-care testing of pathogenic microorganisms and have wide application prospects in biomedicine, clinical diagnosis, environmental monitoring, and food safety.

A new analytical method for chronic kidney disease (CKD) detection utilizing paper spray mass spectrometry (PS-MS) combined with machine learning is presented. The analytical protocol is rapid and simple, based on metabolic profile alterations in urine. Anonymized raw urine samples were deposited (10 μL each) onto pointed PS-MS sample strips. Without waiting for the sample to dry, 75 μL of acetonitrile and high voltage were applied to the strips, using high resolution mass spectrometry measurement (15 s per sample) with polarity switching to detect a wide range of metabolites. Random forest machine learning was used to classify the resulting data. The diagnostic performance for the potential diagnosis of CKD was evaluated for accuracy, sensitivity, and specificity, achieving results >96% for the training data and >91% for validation and test data sets. Metabolites selected by the classification model as up- or down-regulated in healthy or CKD samples were tentatively identified and in agreement with previously reported literature. The potential utilization of this approach to discriminate albuminuria categories (normo, micro, and macroalbuminuria) was also demonstrated. This study indicates that PS-MS combined with machine learning has the potential to be used as a rapid and simple diagnostic tool for CKD.

MicroRNAs (miRNAs) have emerged as a promising class of biomarkers for early detection of various cancers, including ovarian cancer. However, quantifying miRNAs in human blood samples is challenging owing to the issues of sensitivity and specificity. In this study, hsa-miR-200a-3p of the miR-200a sub-family, which is a biomarker of ovarian cancer, was used as the analyte to demonstrate the analytical capability of an integrated biosensing platform using an extremely sensitive surface-enhanced Raman scattering (SERS) nanotag-nanoaggregate-embedded beads (NAEBs), magnetic nanoparticles (MNPs), a pair of highly specific locked nucleic acid (LNA) probes, and a semi-automated paper-based electrowetting-on-dielectric (pEWOD) device to provide labor-less and thorough sample cleanup and recovery. A sandwich approach where NAEBs are modified by one LNA-1 probe and MNPs are modified by another LNA-2 probe was applied. Then, the target analyte miRNA-200a-3p was introduced to form a sandwich nanocomplex through hybridization with the pair of LNA probes. The pEWOD device was used to achieve short cleanup time and good recovery of the nanocomplex, bringing the total analysis time to less than 30 min. The detection limit of this approach can reach 0.26 fM through SERS detection. The versatility of this method without the need for RNA extraction from clinical samples is expected to have good potential in detecting other miRNAs.

The Cu(i)-catalyzed Huisgen cycloaddition click chemistry reaction is of particular interest in the production of paper sheets or natural fiber composites since it leads to the formation of chemically stable bonds between two fibers. This study focuses on the click chemistry modification of kraft pulp fibers. We based our approach on prior research that treated kraft fibers using click chemistry, including propargylation and tosylation reactions. Our focus was on enhancing these treatments to achieve better final sheet properties. After the azidation of tosylated fibers, the crosslinking is carried out with and without a catalyst using water as a solvent to form enhanced kraft fiber sheets. The chemical characterization and the mechanical properties of fibers obtained at intermediate stages confirmed the presence of various functions on the surface of the modified fibers, with a very high degree of substitution and the inter-fiber cross-linking by click chemistry. The presence of inter-fibers covalent bonds led to significant improvements in the mechanical strength and tensile stiffness of the sheets., Competing Interests: There are no conflicts of interest to declare., (This journal is © The Royal Society of Chemistry.)

Parkinson's disease (PD), the second most frequent neurodegenerative illness, is a neurological ailment that produces unintentional or uncontrolled body movements, which should be diagnosed in its early stages to hinder the progression. Monitoring the concentration of α-synuclein (α-Syn) in body fluids can be one of the most efficient ways for PD early detection. In this work, a paper-based electrochemical immunosensor was designed for α-Syn bio-assay in human plasma samples based on encapsulation of the biotinylated antibody on novel dendritic fibrous nanosilica ((KCC-1- nPr -CS 2 )-Ab). For this purpose, a three-electrode system was prepared using stabilization of silver nano-ink on photographic paper. Then, the (KCC-1-NH-CS 2 )-Ab was immobilized on its surface and used to detect the target antigen (α-Syn). After characterization of the prepared substrate by FE-SEM and EDS, the redox behavior of the biosensor was evaluated using chronoamperometry techniques. Under optimal experimental conditions and using a label-free strategy, the engineered immunosensor showed a linear relationship between peak current and antigen concentration in the linear range from 0.002 to 128 ng mL -1 with the lower limit of quantification of 0.002 ng mL -1 . Moreover, this work involves unprecedented use of conductive nano-inks for the manufacture of α-Syn immunosensor, which is aided by the use of a mesoporous silicate dendrimer in encapsulating the α-Syn antibody, thus offering a robust and simple point-of-care device for early PD diagnosis. The ability of the proposed platform to detect small amounts of α-Syn offers a promising approach to developing low-cost, sensitive, and transportable biosensors for Parkinson's disease screening in its early stages., Competing Interests: There are no conflicts to declare., (This journal is © The Royal Society of Chemistry.)

Biogenic amines (BAs) are a group of organic compounds that are produced through the decarboxylation of amino acids by microorganisms. These compounds are commonly found in a variety of foods and are known to cause adverse health effects if consumed in high concentrations. Therefore, the development of sensitive and rapid detection methods for detection and determination of BAs is essential for ensuring food safety. In this study, a novel colorimetric affordable test strip (CATS) was developed for the colorimetric and naked-eye detection of two BAs of ethylenediamine (EDA) and histamine (HIS) in meat samples. Also, triangular silver nanoparticles (AgNPrs) were used as a diagnostic optical probe, and CATS used as a simple, environmentally friendly, inexpensive diagnostic substrate for on - site recognition of meat spoil. The AgNPrs-based optosensor demonstrated high sensitivity and selectivity towards EDA and HIS, allowing for the detection of low concentrations of the BAs in real food samples such as raw chicken and beef. The system presented a UV-vis technique for HIS and EDA analysis in the linear range of 0.1 μM to 0.01 mM, with an LLOQ of 0.1 μM, and 0.05 to 1 μM, with an LLOQ of 0.05 μM, respectively. Additionally, the performance of the designed CATS in the analysis of produced gases was evaluated, highlighting the potential of this simple and cost-effective strategy for the development of BAs diagnostic kits. This approach provides a simple and cost-effective method for detecting BAs in food, which could be beneficial for ensuring food safety and preventing the harmful effects associated with their consumption., Competing Interests: There are no conflicts to declare., (This journal is © The Royal Society of Chemistry.)

A novel, simple, affordable, and reliable colorimetric paper-based analytical device (PAD) was developed for the point-of-use quality testing of ethanol-based hand sanitizers, mainly against adulteration by water. The principle was based on the novel solvatochromism of methylparaben (MPB)-Fe 3+ complex, where water is essential for complex formation and ethanol is necessary for MPB solubility. The intensity of the formed violet color, measured at 528 nm, showed a good correlation ( R 2 ions and MPB on chitosan-modified filter paper. The developed PAD was successfully applied for the quality testing of ethanol-based hand sanitizers using an established color index, where clearly distinct colors were observed as a function of the percentage ethanol (0-100%). The developed test strips could achieve on-site lab-quality results without expensive or sophisticated instruments using a few milligrams of FeCl 3+ and MPB in addition to regular filter paper. Accordingly, it can be used as a test strip for the quality checking of ethanol-based hand sanitizers by end users.3 and MPB in addition to regular filter paper. Accordingly, it can be used as a test strip for the quality checking of ethanol-based hand sanitizers by end users., Competing Interests: The authors declare that they have no known competing financial interests or personal relationships that could have influenced this work., (This journal is © The Royal Society of Chemistry.)

Paper-based ratiometric fluorescence sensors are normally prepared using two or more types of fluorescent materials on a paper chip for simple, low-cost and fast detection. However, the choice of multi-step and one-step modifications on the paper chip affects the analytical performance. Herein, a novel paper-based dual-emission ratiometric fluorescence sensor was designed for the selective detection of tetracycline (TC). Carbon dots (CDs) modified with Eu 3+ were combined with a sealed paper-based microfluidic chip by two methods: one-step grafting of CDs-Eu 3+ on paper and step-by-step grafting of CDs and Eu 3+ on paper. The analytical performance was studied and optimized respectively. The red fluorescence of Eu 3+ at 450 nm is enhanced and the blue fluorescence of CDs at 617 nm is quenched by energy transfer in the presence of TC. Under optimal conditions, TC is selectively determined in the linear range from 0.1 μM to 100 μM with a detection limit of 0.03 μM by the step-by-step grafting method. In addition, the sealed paper chip could effectively prevent pollution and volatilization from the reagent. This technique has been used to analyze TC in seafood aquaculture water with satisfactory results.

In the present work, four CaCO 3 -rich solid residues from the pulp and paper industry (lime mud, green liquor sludge, electrostatic precipitator dust, and lime dregs) were assessed for their potential as co-sequestrating agents in carbon capture. Carbonic anhydrase (CA) was added to promote both CO 2 hydration and residue mineral dissolution, offering an enhancement in CO 2 -capture yield under atmospheric (up to 4-fold) and industrial-gas mimic conditions (up to 2.2-fold). Geological CO 2 storage using olivine as a reference material was employed in two stages: one involving mineral dissolution, with leaching of Mg 2+ and SiO 2 from olivine; and the second involving mineral carbonation, converting Mg 2+ and bicarbonate to MgCO 3 as a permanent storage form of CO 2 . The results showed an enhanced carbonation yield up to 6.9%, when CA was added in the prior CO 2 -capture step. The proposed route underlines the importance of the valorization of industrial residues toward achieving neutral, or even negative emissions in the case of bioenergy-based plants, without the need for energy-intensive compression and long-distance transport of the captured CO 2 . This is a proof of concept for an integrated strategy in which a biocatalyst is applied as a CO 2 -capture promoter while CO 2 storage can be done near industrial sites with adequate geological characteristics., Competing Interests: There are no conflicts to declare., (This journal is © The Royal Society of Chemistry.)

Sodium (Na) metal batteries such as Na-ion batteries and Na-CO 2 batteries are considered to be excellent alternatives to lithium batteries in terms of their potential applications because of their high specific capacity and low cost. However, the sodium anode showed low efficiency and poor cycling in Na-metal battery performance due to the formation of sodium dendrites and serious corrosion. In this work, nitrogen (N), phosphorus (P) co-doped carbon paper (NP-CP) modified with cobalt tetroxide (Co 3 O 4 ) nanoparticles was prepared as the Na anode carrier (Co 3 O 4 @NP-CP), and a sodium-based composite anode (Na-Co@NP-CP) was further prepared by electrodepositing sodium. The experimental results indicate that the N, P and Co 3 O 4 multi-doped carbon paper has good sodiophilicity, which can induce the uniform plating/stripping of Na + ions and inhibit the growth of Na dendrites. The N, P doped carbon paper provides a high surface area and tremendous three-dimensional (3D) framework to effectively reduce the areal current density, facilitate the transfer of electrons, and enhance battery life. Therefore, Na-Co@NP-CP based symmetric cells exhibit stable cycling of over 1100 hours at current densities of 1 mA cm -2 and fixed capacity of 1 mA h cm -2 . When the Na-Co@NP-CP anode couples with CO 2 , the assembled batteries can deliver a stable cycling of 165 cycles at current densities of 500 mA g -1 and limited capacity of 500 mA h g -1 . When Na-Co@NP-CP anode couples with Na 3 V 2 (PO 4 ) 3 (NVP) cathode, the assembled cells exhibit lower hysteresis and batter cycling performance., Competing Interests: There are no conflicts to declare., (This journal is © The Royal Society of Chemistry.)

Exosomal microRNAs (miRNAs) play a pivotal role in intercellular communication, regulating gene expression in target cells, and hold significant promise as cancer biomarkers for early detection and screening. However, achieving precise and viable detection of exosomal miRNAs remains a challenge. This paper proposes an all-in-one detection strategy for breast cancer-derived exosomal miRNA-21 on a pen-based paper chip (PPC). The PPC is constructed using a modified automatic pen and lateral flow assay (LFA), which results in a cost-effective fabrication process. The user only needs to add the sample and trigger the top of the self-contained PPC after a period of time to complete the entire detection process. To enhance the sensitivity of exosomal miRNA testing, an enzyme-free catalyzed hairpin assembly (CHA) is further introduced, enabling highly sensitive detection of miRNA-21 with a limit of detection (LOD) of 25 fmol. Additionally, the detection of miRNAs in differentially-expressed cells and clinical samples has also been successfully achieved with high specificity. Overall, the proposed PPC provides an effective tool for detecting early cancer, monitoring diseases, and establishing point of care testing (POCT).

Albuminuria is a clinical condition associated with poor kidney function, diagnosed by determining the ratio of albumin to creatinine concentrations in patient urine samples. We present a high-throughput paper spray mass spectrometry (PS-MS) method for simultaneous quantitation of urinary albumin and creatinine for potential diagnosis of albuminuria. Minimal (urine dilution) or no sample preparation is required. The analytical performance of the method was evaluated, achieving linear calibration curves ( R 2 > 0.99) with little inter-day variability in the slope ( N = 5 days), exhibiting coefficient of variation (CV) of 8% and 3% for albumin and creatinine, respectively. LOD and LOQ for albumin were 2.1 and 7.0 mg L -1 , and for creatinine were 0.01 and 0.03 mmol L -1 , respectively. Intra- and inter-day ( N = 5) precisions (%CV) and accuracies (%bias) were <10% and ±11%, respectively, for both analytes. The method was applied to determine albumin-to-creatinine ratios in anonymous human patient urine samples ( N = 56), and a correlation of R 2 = 0.9744 was achieved between the PS-MS results and validated clinical method results. This work demonstrates the utility of PS-MS to simultaneously quantify a large (albumin) and a small (creatinine) molecule directly in patient urine samples, and its potential as a tool for clinical albuminuria diagnostics.

π-Conjugated polymers such as polythiophene provide intramolecular wire effects upon analyte capture, which contribute to sensitive detection in chemical sensing. However, inherent aggregation-induced quenching causes difficulty in fluorescent chemical sensing in the solid state. Herein, we propose a solid-state fluorescent chemosensor array device made of a paper substrate (PCSAD) for the qualitative and quantitative detection of metal ions. A polythiophene derivative modified by dipicolylamine moieties (1 poly ), which shows optical changes upon the addition of target metal ions ( i.e. , Cu 2+ , Cd 2+ , Ni 2+ , Co 2+ , Pb 2+ , Zn 2+ , and Hg 2+ ), was highly dispersed on the paper substrate using office apparatus. In this regard, morphological observation of the PCSAD after printing of 1 poly suggested the contribution of the fiber structures of the paper substrate to the homogeneous dispersion of 1 poly ink to suppress aggregation-induced quenching. The optical changes in the PCSAD upon the addition of metal ions was rapidly recorded using a smartphone, which was further applied to imaging analysis and pattern recognition techniques for high-throughput sensing. Indeed, the printed PCSAD embedded with 1 poly achieved the accurate detection of metal ions at ppm levels contained in river water. The limit of detection of the PCSAD-based sensing system using a smartphone (48 ppb for Cu 2+ ions) is comparable to that of a solution-based sensing system using a stationary spectrophotometer (16 ppb for Cu 2+ ions). Therefore, the methodology based on a combination of a paper-based sensor array and a π-conjugated polymer will be a promising approach for solid-state fluorescent chemosensors., Competing Interests: There are no conflicts of interest to declare., (This journal is © The Royal Society of Chemistry.)

Cellulose, as a naturally abundant and biocompatible material, is still gaining interest due to its high potential for functionalization. This makes cellulose a promising candidate for replacing plastics. Understanding how cellulose interacts with various additives is crucial for creating composite materials with diverse properties, as it is the case for plastics. In addition, the mechanical properties of the composite materials are assumed to be related to the mobility of the additives against the cellulose. Using a well-defined cellulose model surface (CMS), we aim to understand the adsorption and desorption of two polymeric particles (core-shell particles and microgels) to/from the cellulose surface. The nanomechanics of particles and CMS are quantified by indentation measurements with an atomic force microscope (AFM). AFM topography measurements quantified particle adsorption and desorption on the CMS, while peak force AFM measurements determined the force needed to move individual particles. Both particles and the CMS exhibited pH-dependent charge behavior, allowing a tunable interaction between them. Particle adsorption was irreversible and driven by electrostatic forces. In contrast, desorption and particle mobility forces are dominated by structural morphology. In addition, we found that an annealing procedure consisting of swelling/drying cycles significantly increased the adhesion strength of both particles. Using the data, we achieve a deeper understanding of the interaction of cellulose with polymeric particles, with the potential to advance the development of functional materials and contribute to various fields, including smart packaging, sensors, and biomedical applications.

A new method utilizing fluorescent ratiometry is proposed for detecting putrescine and spermidine. The method involves the use of a fluorescent probe comprising a 2D halide perovskite synthesized from octadecylamine-iodine and PbI2via a grinding-sonicating technique, along with a Eu3+-complex. Upon excitation at 290 nm, the probe fluoresces at two distinguishable wavelengths. The addition of putrescine and spermidine significantly decreases the emission of the 2D halide perovskite at 496 nm, while the emission of the Eu3+-complex at 618 nm remains stable. The color changes of the probe depend on the concentration of putrescine and spermidine, and the assay offers linearity over a wide concentration range (30–4000 ng mL−1), a low detection limit (4 ng mL−1 for putrescine, and 7 ng mL−1 for spermidine), and a quick response time. Furthermore, a portable device based on a smartphone can be used to record the color change of the paper test strip using the prepared fluorescent materials. The fluorescence quenching mechanism of the probe is explained as dynamic quenching. [ABSTRACT FROM AUTHOR]

A novel, biodegradable substrate based, and cost-effective flexible electrochemical sensor was developed for the highly selective and sensitive detection of one of the major neurotransmitters, dopamine, which can be utilised as a disposable electrode for point-of-care diagnostic applications. The active material CuSnB decorated over cellulose paper exhibits good sensitivities of 3.92 μA μM -1 cm -2 with a limit of detection of 0.5 nM. Moreover, the flexible sensor demonstrated superior selectivity towards co-existing metabolites such as ascorbic acid, glucose, and uric acid, in addition to stability at various mechanical deformations.

A paper-based ratiometric fluorescent sensing platform has been developed for glucose detection based on a dual-emission fluorescent probe consisting of carbon quantum dots (C QDs) and CdTe QDs. When the two kinds of QDs are mixed, the fluorescence of C QDs is reversibly quenched by CdTe QDs. However, in the presence of glucose, the fluorescence of CdTe QDs is quenched by H 2 O 2 catalyzed by glucose oxidase (GOx), which restores the fluorescence of C QDs. The proposed paper-based ratiometric fluorescent sensing platform exhibited good sensitivity and selectivity towards glucose. The working linear range was 0.1 mM to 50 mM with a limit of detection (LOD) of 0.026 mM. Additionally, the proposed paper-based sensor possesses viability for the determination of glucose in actual urine samples., Competing Interests: The authors have no conflict to declare., (This journal is © The Royal Society of Chemistry.)

The effective integration of nanomaterials with underlying current collectors is a key factor affecting the performance of nonenzymatic glucose sensors, where an inappropriate integration structure often leads to poor electron transport and instability. In this work, a seamless integrated electrode was constructed by the in situ immobilizing of a nickel-based metal-organic framework (Ni-MOF) on a three-dimensional (3D) conductive nickel foam (NF) for highly sensitive and durable glucose sensing. Facilitated by a rapid microwave-assisted reaction, a robust interfacial interaction between the Ni-MOF and the substrate was established through in situ conversion from nickel oxide (NiO). The fabricated Ni-MOF/NF electrode exhibits an excellent limit of detection (LOD) of 2.65 μM and an impressive sensitivity (14.31 mA cm-2 mM-1) within the linear range (4-576 μM), which is significantly boosted compared with that of an electrode prepared by a typical drop-casting method (3.56 mA cm-2 mM-1 in 4-1836 μM). Characterization and electrochemical tests reveal that this integrated structure on the one hand contributes to fast electron transport and thus has enhanced sensitivity and on the other hand leads to exceptional durability with its structural integrity maintained under bending, shaking, and ultrasonication. Moreover, this seamless integration method was also employed to immobilize the Ni-MOF converted from the pre-chemically deposited NiO layer on another type of substrate, 3D carbon paper (CP), demonstrating the versatility of this facile strategy in creating diverse electrochemical electrodes for applications beyond glucose sensing. [ABSTRACT FROM AUTHOR]

Hydrogel-based flexible electronics have received increasing attention owing to the requirement in a variety of applications. However, the design and development of underwater and self-adaptive high-temperature strain sensors remain a significant challenge because of the swelling and dehydration of hydrogels in aquatic environments and extreme climate conditions. Herein, a versatile gel with superior self-adhesiveness, long-lasting underwater stability, excellent high-temperature tolerance and long-term non-drying properties is successfully prepared, which can serve as a wearable sensor for precisely and reliably detecting diverse body movements and the direction of human movements in air and aquatic environments. Meanwhile, based on the Morse code expression, the as-fabricated gel sensor can also be utilized as a wearable communication device for delivering various messages to the receiver. Furthermore, a wireless sensor with high-temperature adaptability is constructed, which can transmit in real time the motion signals at high temperature to the specific APP of a smartphone at room temperature via wireless communication. This strategy provides a new perspective and great convenience for motion monitoring under harsh conditions. In particular, the as-prepared gel demonstrates an obvious transparency-shifting behavior in different polar solvents, thus inspiring us to engineer it as a novel water-writing paper for achieving repeatable "writing–erasing" applications. [ABSTRACT FROM AUTHOR]

Organophosphorous pesticides pose a significant threat to public health, making its detection critical. Herein, a new fluorescent metal–organic framework, Eu-NDC, was synthesized, which possessed a 3D supramolecular structure assembled through π⋯π interactions between the naphthalene rings in its adjacent coordination-bonded layers. Then, four different products of the Eu-NDC MOF (Eu-NDC-1/2/3/4) with different morphologies were further obtained by altering the ratio of the raw materials. Among them, the fluorescence properties and BET surface area of the micro-nanoscale Eu-NDC-3 were significantly enhanced, making it the most favorable for detection. Eu-NDC-3 as a turn-off fluorescence probe for methyl paraoxon (DMNP) exhibited excellent sensitivity and selectivity, anti-interference and durability. Thus, considering these features, an intelligent logic gate was designed, showing great promise for application in smart sensing. Furthermore, an Eu-NDC-3-loaded electrospun fibrous strip was fabricated as a portable and in situ platform for visual DMNP assay. [ABSTRACT FROM AUTHOR]

Rapid, sensitive, and quantitative detection of biomarkers is needed for early diagnosis of disease and surveillance of infectious outbreaks. Here, we exploit a plasmonic syringe filter and surface-enhanced Raman spectroscopy (SERS) in the development of a rapid detection system, using human IgG as a model diagnostic biomarker. The novel assay design facilitates multiple passages of the sample and labeling solution through the detection zone enabling us to investigate and maximize sampling efficiency to the capture substrate. The vertical flow immunoassay process in this study involves the utilization of filter paper embedded with gold nanoparticles (AuNPs) to form a plasmonic substrate. Capture antibody (anti-human IgG) is then immobilized onto the prepared plasmonic paper and inserted into a vertical flow device (syringe filter holder). Sample solution is passed through the filter paper and the target antigen (human IgG) is selectively captured by the immobilized antibody to form an antibody–antigen complex. Next, functionalized AuNPs as extrinsic Raman labels (ERLs) are passed through the filter paper to label the captured biomarker molecules forming a layered structure. This sandwiched geometry enhances plasmonic coupling and SERS signal to provide highly sensitive detection of biomolecules. Systematic studies to investigate the impact of multiple infuse/withdraw cycles of the sample and labeling solutions reveal that antigen and ERL binding are maximized with 10 and 20 cycles, respectively. The optimized assay achieves a detection limit of ∼0.2 ng mL−1 for human IgG with a total assay time of less than 5 minutes, meeting the demands for rapid point of care diagnostics. Additionally, the optimized platform was implemented in the quantitative analysis of the SARS-CoV-2 nucleocapsid protein, the typical target in commercial, FDA-approved rapid antigen tests for COVID-19. [ABSTRACT FROM AUTHOR]