Search

• Hydrological and erosive response at event scale for a recently burned catchment. • Comparison of two hydrological models, OpenLISEM and MOHID Land. • Parametrization based on variation in boundary conditions characterizing each event. • Models performance revealed the importance of subsurface flow at event scale. • Ash and sediment movement during large event needs different model parameterization. Wildfires are a source of instability for the natural water cycle in forested watersheds, endangering the water quantity and quality reaching downstream water bodies. The faster hydrological response of a burned area leads to increased runoff and transport of sediment and ash particles during and after rainfall events. Therefore, the use of an adequate spatiotemporal resolution in hydrological models is necessary to properly estimate post-fire impacts. Especially when addressing hydrological events such as flash floods and debris flows, which are highly unpredictable and are characterized by short duration and high impact outside the burned area. This study aims to compare the ability of two hydrological models to simulate the hydrological response and sediment transport during the first year after a fire to ultimately understand which one would best serve as a post-fire hydrological predicting tool at event scale. To achieve this goal, OpenLISEM, an event-based hydrological model, and MOHID Land, a continuous model with variable timestep, were compared. Driven by several limitations identified in previous modeling exercises at this scale during the calibration phase, this work performed a parametrization through the variation in boundary conditions characterizing each event. OpenLISEM and MOHID Land models exhibited similar capabilities in simulating runoff during the first post-fire year. However, the larger erosion input parameters required by MOHID Land increase the complexity of erosion prediction and increase equifinality. In addition, MOHID Land limited capacity to perform sensitivity and uncertainty analyses emerged as a major disadvantage, hindering the assessment of the reliability of the model's predictions. Despite its limitations for not integrating subsurface flow and base flow, OpenLISEM is the most suitable model for assessing post-fire impacts on runoff and sediment production at the event scale, because of its ease of implementation and its reduced computational requirements. [ABSTRACT FROM AUTHOR]

• Mass movement is an important erosion mode and sediment source in gully network. • Mass movement increased sediment concentration and led to peak sediment concentration. • Mass movement was prone to be triggered by rainfall with a medium-duration and moderate-intensity. • Rainfall amount and slope gradiet determined the trigger and total volume of mass movement. Mass movement erosion on the gully sidewalls is recognized as an important erosion mode and sediment source in hilly and gully watersheds. However, the trigger of mass movement erosion and transport of gravity-detached material remain poorly understood. A series of rainfall simulation experiments were conducted on six loess gully sidewall models, with a height (1 m), three rainfall (60 mm, 48 mm and 24 mm) and two slope gradients (70° and 80°), to quantitatively explore the sensitivity factor and transport mechanisms of mass movement. Results revealed that the accumulation volume and initiation of the mass failure were significantly influenced by rainfall amount. The accumulative volume of failure events was observed to increase in a linear pattern with increasing rainfall amount. The minimum cumulative rainfalls for the initiation of mass failure on the loess gully sidewalls were approximately 43.6, 28.2 and 65.6 mm for short-duration and high-intensity, medium-duration and moderate-intensity and short-duration and moderate-intensity rainfalls, respectively. This implied that the initiation of mass failure was more prone to rainfall events with a medium-duration and moderate-intensity than those with a high intensity and short duration. Rainfall amount and initial slope gradient were the most sensitive elements driving the number and volume of the mass movement erosion. Mass movement erosion raised sediment concentration, but the eroded material was unable to be transported by runoff in a timely manner. Average sediment concentrations at the model outlet increased by 1.9–11.9 times following the occurrence of mass failures compared to those before. A low instantaneous sediment delivery ratio of 0.032 for the mass movement erosion. The experimental findings help comprehend the influence of mass movement erosion on sediment supply on the gully sidewall in the hilly and gully network, i.e. the Loess Plateau. [ABSTRACT FROM AUTHOR]

• Ridge slope erosion included inter-rill erosion, headward erosion, and rill erosion process. • Erosion rate reached the maximum during headward erosion process. • The dominated erosion process was detachment-limited after headward erosion occurring. • Re-detachment, transport, and deposition simultaneously occurred with the appearance of headward erosion. Extreme rainfall is becoming more frequent and intense, which no doubt increases the risks and uncertainty of water erosion in widely-used contour ridge systems. Ridge slope erosion can increase the probability of contour failure occurrence and then induce contour ridge losing anti-erosion properties. However, there is little understanding of ridge slope erosive process controlled by contour ridge system responding to extreme rainfall. In this study, five rare earth elements were applied in different ridge segments and soil layers to monitor the successive development of ridge slope erosion process under extreme rainfall in contour ridge system. Simulated rainfall experiments at high rainfall intensity (100 mm h−1) lasting for 60 min were conducted in runoff plots with ridge tillage practices characterized by microtopography indices and ridge geometry indices. Results showed that three sub-processes were observed for ridge slope erosion, including inter-rill erosion, headward erosion, and rill erosion. Headward erosion mainly resulted from the break-point at ridge surface and sidewall collapse at ridge toe, and the pouring of ponding water in furrow greatly promoted rill development. Erosion rate was the largest during headward erosion process, and rill erosion contributed the most to eroded source. The dominated erosion process was transport-limited during inter-rill erosion process, and detachment-limited during headward and rill erosion processes. Sediment transport and deposition processes as well as their transformation occurred simultaneously after the development of headward erosion. Eroded sediment was mainly from the low part of ridge, which was transported by raindrop-impacted sheet flow or overflow. These findings provide better responding of agricultural tillage to global climate change and references for the development of physically-based erosion models. [ABSTRACT FROM AUTHOR]

• The sediment transport capacity was developed for loessal slopes. • Two-dimensional erosion numerical model was developed for loessal slopes. • Erosion numerical model could accurately simulate slope runoff and sediment process. Simulated slope erosion sediment yield and its development process have great significance for quantitative evaluation of erosion and its sources. In this study, a loess slope erosion experiment was implemented indoors to establish a sediment transport capacity formula suitable for loess slope erosion. A two-dimensional slope erosion numerical model was developed with corrected sediment transport capacity formula, and the model was verified by a simulated indoor slope rainfall erosion experiment. The results showed that the corrected slope sediment transport capacity formula is suitable for loess slopes. The proposed two-dimensional slope erosion numerical model could simulate runoff and sediment processes in a relatively more accurate. The most severely eroded areas were the middle and lower parts on erosion spatial contribution based on the simulation erosion results. Good agreements between the simulated and observed results were found for erosion and its spatial distribution. The research results can further improve loessal slope erosion process simulation and prediction. [ABSTRACT FROM AUTHOR]

In this paper, we examine the effect of vegetation on soil erosion, runoff generation and sediment transport on saline rangeland hillslopes. Rainfall simulations were conducted at a fixed 114 mm/h intensity on 6 m × 2 m erosion plots with varying degrees of vegetation. Plots were grouped into three categories (L, M and H) based on their canopy cover (L: <5%, M: 5–19%, H: >19%) and selected to limit variations in slope across canopy cover groups. Runoff and sediment samples were combined with three dimensional (3D) reconstruction data used to monitor soil surface microtopographic changes. Runoff initiation was significantly delayed on the L plots but cumulative runoff after 20 min of rainfall simulation indicated a positive effect of vegetation on infiltration processes. Cumulative sediment after 20 min of rainfall was similar across vegetation cover categories. The 3D data suggest that vegetation reduced net sediment delivery from the plots by primarily increasing opportunities for deposition while marginally affecting gross soil erosion. Plots with H vegetation cover experienced lower 3D-estimated erosion volumes but average erosion depth on L plots was lower than that on plots with M and H vegetation covers. Lower runoff volumes on M and H plots may have been compensated by greater runoff erosivity on these plots as runoff was concentrated in a narrower inter-patch space compared to L plots. This study highlights the need for an increased integration between traditional runoff measurement techniques and 3D reconstruction methods. [ABSTRACT FROM AUTHOR]

• Effective sediment sizes were determined along a gradient of soil structural stability. • Sediment average size exhibited a unimodal variation with soil structural stability. • Suspension-saltation dominated sediment transport for low and high stable soils. • Suspension-saltation and rolling jointly dominated erosion for medium stable soils. • Soil structural stability determined rainfall intensity effect on sediment transport. Sediment transport patterns (suspension, saltation and rolling) not only depend on flow hydrodynamic characteristics, but also on sediment properties, both of which are largely influenced by soil structural stability. However, how sediment sizes and transport patterns response to original soils over a wide range of structural stability remains unclear. Herein, field plot rainfall simulation experiments on five soils along an increased gradient of structural stability were conducted at two rainfall intensities of 45 and 90 mm h−1 to investigate effective sediment size characteristics and associated transport patterns in sheet erosion. Differing from runoff and sediment yield, sediment sizes were most influenced by soil structural stability (F = 386.9) rather than rainfall intensity (F = 246.7, p < 0.001). Mean weight diameter of sediment (0.16–0.84 mm) and the proportion of coarse particles (>0.25 mm) exhibited a unimodal variation with increased soil structural stability. The effective sediment size distribution shifted from unimodal with the peak at < 0.10 mm for low and high stable soils to bimodal with two peaks at < 0.10 mm and 0.5–1 mm for medium stable soils. Correspondingly, suspension-saltation (>74 %) dominated sediment transport for low and high stable soils, which was determined by fine sized fragments from aggregate breakdown and small flow transport capacity, respectively; while both suspension-saltation (<0.10 mm) and rolling (>0.25 mm) jointly contributed to sediment transport for medium stable soils, which was controlled by the interaction between fragment size and flow transport capacity. Moreover, the positive effect of rainfall intensity on sediment sizes was more remarkable for the medium than for the low and high stable soils. A conceptual model of sediment transport mechanisms in response to soil structural stability is firstly proposed, which merits consideration in the future development of erosion modeling and soil conservation techniques. [ABSTRACT FROM AUTHOR]

• Demonstration of rise and fall of carbon discharge with time. • Demonstration of enrichment of sand in loose layer above soil. • Demonstration of no carbon enrichment is sediment at the steady state. Soil carbon losses from sheet and interrill erosion areas have an impact on the global carbon cycle. Sediment discharged in many experiments where artificial rainfall has been applied to sloping soil surfaces show greater proportions of carbon in the sediment than found in the cohesive soil source. In many cases, conclusions drawn from these experiments fail to recognise that the enrichment of carbon in the sediment discharge is a result of unsteady conditions that occur before the steady state develops. It is known that particles of sand of different sizes move at different rates when raindrop induced salation occurs with the result that initially the particle size distribution is finer than the source but tends towards that of the source as time progresses. The presence of carbon in aggregates influences the density of aggregates. Here a qualitative model of sediment transport of sand and coal particles by raindrop induced saltation is used to demonstrate time varying enrichment of coal resulting from the effect of carbon on particle settling velocity. The model also demonstrates how the layer of loose particles that develops on top of the cohesive soil surface influences the relative amounts of carbon and sand in the sediment discharges. The steady state is not achieved until the slowest moving particle detached at the farthest distance from the downslope boundary is discharged. That may not be achieved in many of the experiments reported in the literature. [ABSTRACT FROM AUTHOR]

Computer based landscape evolution models can provide insight into both erosion rates and processes (i.e. sheetwash, rill, gully erosion). One important data requirement of these models is long term, high quality, high-temporal resolution rainfall data (given that the physical nature of the erosion process is strongly related to rainfall). However, in many cases such data is limited - data is often short, incomplete or not of a sufficient temporal resolution. Therefore, the aim of this study was to test the sensitivity of modelled erosion rates to small changes in rainfall input. To achieve this we firstly assess the existing rainfall data from an established weather station and secondly, stochastically generate rainfall time series based on the longest and most reliable rainfall data. We then test the sensitivity of different rainfall sequences on sediment output using a well-tested landscape evolution and sediment transport model (CAESAR-Lisflood) over a simulated period of 100 y on a proposed rehabilitated mine landform. It was found that each rainfall scenario produces a unique pattern of erosion (i.e. the location and extent of the gullies is variable). Further, each rainfall scenario produces a unique pattern of sediment output that suggests non-linear processes. Importantly, this is the first time stochastically generated rainfall has been employed in landform evolution modeling and provides a statistical approach to quantify sediment transport and landform evolution. The method demonstrates a risk based approach and allows rainfall, runoff and sediment transport studies to be conducted in data poor environments. The findings clearly demonstrate that rainfall variability can greatly affect sediment transport and form of erosion as well as landscape evolution. This information is of particular importance for the design and testing of rehabilitated landscape systems such as post-mining landscapes. [ABSTRACT FROM AUTHOR]

• Physically based 2D hydrodynamic and sediment transport model, CCHE2D. • High resolution mesh, topography photogrammetry, experimental landform evolution. • Watershed hydrology, raindrop soil detachment, displacement, erosion and transport. • Distributed solution, tilled watershed, cornfield tillage ridge and furrow morphology. • Simulated runoff, sediment transport, landform evolution; channel network analysis. Soil and gully erosion is a critical threat to sustainable agricultural land management and productivity. Soil erosion by rain splash, sheet runoff, and concentrated flow are complex problems conditioned by the combined interactions of soil physical properties, hydrology, human activity, landscape topography, and climate. Effective management of erosion processes driven by rainfall and surface runoff requires a combined effort of field observation, physical experimentation, and numerical simulation. A physically-based hydrodynamic numerical model, CCHE2D with updated raindrop erosion effects, is applied to simulate landscape evolution processes as a result of raindrop impact and overland flow. The numerical model simulates a thin layer of runoff and concentrated flow over complex terrains, and predicts sediment transport due to raindrop splash detachment, transport and soil surface erosions. Soil erosion and landform evolution simulations due to rainfall are presented for an experimental landscape and a tilled large scale agricultural field. Photogrammetric field data were collected using an unmanned aerial system (UAS) following planting and subsequent rainstorms. Numerical simulation results agreed well with the observed experimental soil surface topography, sediment yield, and drainage network developments. The simulated soil and gully erosion in the tilled field also agreed well with observations. This research successfully demonstrates how high resolution spatial and temporal topographic measurements in experimental and field landscapes can be simulated and interrogated by 2D physically-based hydrodynamic and morphodynamic models. The accurate predictions of tillage field and gully erosion process in agriculture watersheds with complex tillage conditions also indicated the usefulness of the model for studying soil and landscape degradation. [ABSTRACT FROM AUTHOR]

[Display omitted] • Total volume and peak discharge are the most important drivers of sediment transport. • Antecedent moisture condition is correlated only with the initial discharge of floods. • Hysteresis loops between SSC and Q are analyzed with the hysteresis index (HI). • Negative HI are predominant indicating delayed SS transport and distant SS sources. • In the catchment soil erosion from hillslopes is the dominant process. This study aimed to evaluate the drivers of suspended sediment (SS) transport by analyzing the flood events recorded from July 2010 to June 2011 in the Celone River basin (Apulia, S-E Italy). High-resolution data of rainfall, streamflow (Q), and measurements of suspended sediment concentrations (SSC) were used to carry out the multivariate analysis. Among the initial 18 variables, the Principal Component Analysis revealed that total volume (m3), peak discharge (Qmax, m3/s), and the flood duration were the most important factors influencing SS transport. Total rainfall and total kinetic energy recorded in the gauging station located in the lowland were also important factors, whereas the same rainfall variables recorded in the remote mountainous area of the basin had a minor influence on SS transport. Antecedent moisture conditions were significantly correlated only with the initial discharge of the flood. Hysteresis loops between SSC and Q were analyzed for each flood event by using the hysteresis index (HI). Results showed that this catchment was dominated by anticlockwise loops (negative values of HI) representative of delayed SS transport and of distant SS source areas in terms of the gauging station. These results also suggested that soil erosion from hillslopes was the dominant process compared with channel and bank erosion and that there was no exhaustion of sediment availability in the basin. [ABSTRACT FROM AUTHOR]

• Linkage between soil surface microrelief and overland flow was examined. • Differently oriented wheel tracks served as water flow paths or as sediment sinks. • Increase of surface connectivity after a rain was shown by functional connectivity. • Structural connectivity showed reorganization of the surface runoff pathways. Although wheel tracks cover only a small portion of the surface of agricultural fields, their effect on surface runoff and sediment transport is substantial. Wheel tracks change the microrelief of the soil surface, and influence how the surface is further altered by rainfall and runoff. This study presents a plot-scale microrelief analysis of a tilled surface with wheel tracks under simulated rainfall. Digital elevation models of the microrelief with 1 cm spatial resolution were obtained using the Structure from Motion method. The random roughness, the structural connectivity, and functional connectivity were calculated for before-rainfall and after-rainfall soil surface conditions. The experiments were carried out on inclined, freshly-tilled plots (8 m long, 2 m wide). The wheel tracks were created by four passages of machinery in the slope direction (SWT) and in the contour-line direction (CWT). The experiments were compared to reference plots without wheel tracks (NWT). The wheel tracks increase water and sediment connectivity if they are oriented in slope-wise direction. Microrelief analysis shows that SWT drains water from the surrounding soil. The soil surface adjacent to SWT can also become more connected with the wheel track, due to changes in microrelief introduced by rainfall and runoff. The calculated higher connectivity in the SWT plot corresponded to the measured increased sediment loads. This suggests faster overland flow and therefore shorter flow pathways on the soil surface microrelief. CWT leads to a decrease in the water and sediment connectivity compared to the NWT and SWT plots. Although the surface runoff can overflow the CWT, the network of flow paths results in decreased flow velocity and a slower sediment transport rate. However, the CWT effect is not permanent, and declines as the wheel tracks become silted with the deposited sediment. It is shown that detailed microrelief data provide relevant information for a study of the changes in flow routing in a tilled agricultural field with the presence of a wheel track. SWT accelerates the runoff and especially the sediment transport. During a rainfall event, the hydraulic connection between the wheel track and the surrounding soil increases dramatically. CWT reduces the surface runoff and also the sediment transport. In the long term, rainfall events and surface runoff alter the microrelief connectivity, causing the soil surface to be more hydraulically connected, irrespective of the wheel track orientation. This study demonstrates the effect of wheel tracks on water and sediment transport. The results draw attention to the importance of appropriate soil protection measures, as a bare unprotected surface microrelief exposed to rainfall leads to increased sediment connectivity. [ABSTRACT FROM AUTHOR]