Search

As a kind of organic basic compound containing nitrogen, biogenic amine is released from food spoilage and considered as an indicator for monitoring food freshness. Herein, an excellent dual-emission ratiometric fluorescent sensor for eight kinds of biogenic amines was established via the facile mixing of pH-responsive carbon dots and Rhodamine B. The developed sensor shows a rapid response (10 s), low limit of detection (0.733–3.943 μM) and a wide linear range (0–150 μM). More importantly, a portable fluorescent filter paper was prepared by simple dispersing the filter paper in a solution mixture of carbon dots and Rhodamine B. The obtained fluorescent filter paper based sensor showed an obvious color change in the presence of biogenic amine vapor derived from shrimp and mushroom. The results revealed that this sensor could realize the on-site and visual detection of biogenic amines in real food samples, making it suitable for potential application in food safety monitoring. [ABSTRACT FROM AUTHOR]

A simple, rapid chemical coating and patterning method was developed and optimized for paper-based substrates for use in paper spray mass spectrometry (PS-MS). A variety of chlorosilanes were explored for coating paper substrates, and their effectiveness in forming hydrophobic surfaces was characterized via contact angle goniometry, scanning electron microscopy, and energy dispersive X-ray spectroscopy. Trichloromethylsilane was selected as the primary coating agent because of the short time required to produce a hydrophobic surface (contact angle > 130°), as well as the ease of patterning. Patterning was performed using 3D-printed masks and an oxygen/plasma cleaner. Optimal mask thickness and oxygen/plasma cleaning parameters were determined to produce channels varying from 0.5 to 2.5 mm in width. The effectiveness of the patterned substrates for PS-MS was determined via analysis of four antiretrovirals: emtricitabine, lamivudine, efavirenz, and dolutegravir. Calibration curves were made for each antiretroviral at varying channel widths, and the limits of detection and limits of quantification for each drug were determined. These results show that this patterning method results in an average 7.2-fold improvement in sensitivity and an average 190-fold improvement in limits of detection over uncoated paper substrates in a neat matrix. In a proof-of-concept experiment, calibration curves were generated for each antiretroviral in urine. A patterned paper substrate with a 2-mm channel resulted in an average 7.4-fold improvement in sensitivity and an average 18-fold improvement in limits of detection over uncoated paper substrates. [ABSTRACT FROM AUTHOR]

Based on surface biomolecular imprinting technology, a rotary microfluidic electrochemical paper-based chip (MIP-ePADs) was proposed for sensitive and selective detection of human interleukin 6 (IL-6) and procalcitonin (PCT). Compared with the traditional method, the sample can be added directly on the MIP-ePAD by rotating the working electrode, which avoids the loss of the liquid to be tested and greatly simplifies the process of electropolymerization imprinting and template elution. Our experimental results show that linear concentration ranges of IL-6 and PCT in the electrochemical molecularly imprinted microfluidic paper-based chip ranged from 0.01 to 5 ng mL−1, with their detection limits being 3.5 and 2.1 pg mL−1, respectively. For the detection of actual serum samples, there was no significant difference between the results of MIP-ePADs and the traditional electrochemiluminescence method used in hospitals, indicating that the paper-based chip can be used for stable and accurate analysis and detection. The chip greatly reduces the cost of clinical trials due to its advantages of easy preparation and low cost. The chip can be used for the analysis of non-antibody inflammation markers and can be widely used in home and hospital treatment detection. This method will not only play an important role in rapid detection, but also provide new ideas for the improvement of rapid detection technology. [ABSTRACT FROM AUTHOR]

We created novel Pd/CB-Ni@rGO nanomaterials for glucose detection. The as-synthesized nanomaterials were dropped on the electrode surface using the drop casting technique. The prepared electrode was then attached to a paper-based device containing the sample zone and the reaction zone, enabling plasma isolation and an enzymatic reaction for glucose detection in whole blood. The nanomaterials and surfaces of electrodes were characterized by FTIR, TEM, and SEM. The proposed approach is a disposable glucose detection method that is unaffected by protein fouling on the electrode, and it requires only one drop of human blood. Therefore, there is no need for extensive sample preparation, and there is less sample consumption. Under optimal conditions, Pd/CB-Ni@rGO can accurately measure blood glucose levels with a linear range of 7 to 7140 μM (R2 = 0.9986) and a low detection limit of 0.82 μM. Besides, the developed sensor shows excellent anti-interference capacity, stability, and satisfactory reproducibility and repeatability. Importantly, Pd/CB-Ni@rGO was successfully applied for glucose in whole blood from 4 volunteers, with results that correlated well with those obtained using an Accucheck glucometer at a 95% confidence level. Given its low cost, high accuracy, and ease of use, the blood glucose sensor holds significant potential for clinical use and broadens the area of future noninvasive sensor development. [ABSTRACT FROM AUTHOR]

This communication describes the development of polyvinyl chloride electrochemical system in which a paper layer loaded with reagents is inserted into the device, demonstrating a new concept of a paper card-like pad for a reagent-free and easy measurement of the target analyte in solution. This device detects glucose in artificial tears in the range of 0.2–2 mM with a detection limit of 50 μM by simply adding the artificial tears to the paper card-like pad. The novel configuration goes beyond the state of the art, widening the application range of paper in the design of smart analytical devices. [ABSTRACT FROM AUTHOR]

Pesticide residues are a serious problem towards agriculture, environment and food safety, so it is highly desirable to develop a swift, efficient and portable pesticide detection method. A fluorescence visual sensing method for glyphosine based on a nitrogen-doped biomass carbon quantum dot (N-CQD) paper-based sensor was developed. The fluorescence signal was quenched by Fe3+ in a static quenching process, and then the fluorescence of N-CQDs was recovered after adding glyphosine. Under the optimal experimental conditions and when tested with a fluorescence spectrofluorometer, the detection of glyphosine showed a two-stage linear pattern in the range of 0.1–0.6 μM and 0.6–1.6 μM with a detection limit of 0.075 μM. Then, the RGB values of different concentrations of glyphosine on the filter paper chip were detected by the software of the smartphone-color identifier. The logarithm of the glyphosine concentration was linearly related to the G value of RGB in the range of 0.25–10.00 mM and with a detection limit of 0.15 mM. The method was applied to measuring glyphosine-spiked juice and flour samples, and the recovery rates were 87.60–112.69% and 93.27–105.83%, respectively. The proposed N-CQDs/Fe3+ system had wide applications, and it was expected to be fast and effective at detecting pesticide residues. [ABSTRACT FROM AUTHOR]

Sodium thiocyanate (NaSCN) is a naturally antibacterial component in milk, but excessive consumption of thiocyanate may cause potential risks to human health. Currently available methods for the detection of thiocyanate have some disadvantages such as poor sensitivity and high price. Here, we report a robust and cost-effective method to detect NaSCN based on paper substrates deposited with in situ reduced Ag nanoparticles by surface-enhanced Raman spectroscopy (SERS). Densely packed multilayer AgNPs provide uniform narrow nanogaps, which exponentially enhance the Raman signals. Moreover, these homogeneous narrow hotspots ensure that this method has high sensitivity (the limit of detection is 10−12 mol L−1), a wide linear range (from 10−9 mol L−1 to 10−4 mol L−1), and remarkable reproducibility (the coefficient of variation within a SERS sensor is 6.5%). Spiked milk samples were detected and the recovery rates of NaSCN were in the range of 95.1%–108.0%. This paper-based SERS sensor offers great potential for sensitive NaSCN detection and milk analysis. [ABSTRACT FROM AUTHOR]

Herein, a unique electrochemiluminescence (ECL) sensor combined with a paper electrode was proposed for the detection of phenylalanine (L -Phe) in blood samples. The L -Phe detection was performed by converting L -Phe into ammonia using phenylalanine ammonia-lyase (PAL) enzyme and the ECL signal of Ru(bpy)32+ was produced in combination with ammonia as a co-reactant. In this report, we used AuNP decorated paper electrodes to obtain the ECL signal of Ru-(bpy)32+ in the presence of NH3. The produced ammonia molecules were carried to the working electrode and their contact with the sample was cut off. Since there was no contact between the sample matrix and the electrode, the developed method achieved excellent selectivity. According to experimental data, a linear increase of the ECL signals with the logarithms of varying L -Phe concentrations between 1.5 × 10−2 and 1.211 mM was observed with a correlation coefficient (R2) of 0.9898 and a limit of detection (LOD) of 8.4 × 10−3 mM. The proposed method was efficiently applied for L -Phe detection in reference blood samples and the average recovery was calculated as 96.8%. Furthermore, the HPLC-UV method as a comparison verified that the recovery values provided by the proposed method were acceptable with a similarity of 95.1% for L -Phe detection in a reference blood sample. The results showed that the developed ECL sensor combined with the paper electrode can be considered as a promising unique and powerful technique for a point-of-care diagnosis of PKU. [ABSTRACT FROM AUTHOR]

Paper-based microfluidic solution sampling is a viable option for potentiometric sensors to be used for the determination of analytes in samples with high solid-to-liquid ratios. Unfortunately, heavy metal sensitive electrodes cannot be easily integrated with paper-based solution sampling as heavy metals have strong physicochemical adsorption affinity towards paper substrates. In this work, paper substrates were modified with an ion-selective membrane (ISM) cocktail (used for the preparation of Pb2+-ion-selective electrodes (ISEs)) and coupled with model heavy metal Pb2+-ISEs. It was found that the super-Nernstian response of Pb2+-ISEs was eliminated when 10 to 50 mg ml−1 of the ISM cocktail was used for the modification of paper substrates. The modification of the paper substrates by Pb2+-ISM allowed the elimination of adsorption sites. In addition, it resulted in an improvement of sensor performance in terms of their detection limits to be similar to those for conditioned electrodes in standard beaker-based measurements. It is believed that the elimination of super-Nernstian response of the electrodes and improving the potentiometric responses and detection limits of ISEs were attributed to the compatibility improvement of the paper substrates and Pb2+-ISEs to the same type of ISM. [ABSTRACT FROM AUTHOR]

As a part of our ongoing research, we have synthesized a new fluorescence probe, p-C4A, based on a calix[4]arene substituted with 4-aminoquinoline moieties with amide linkages. p-C4A can selectively recognize Li+ and PO43− ions and has been characterized via an emission study, an absorption study, ESI-MS spectroscopy, a 1H NMR study and cyclic voltammetry. The fluorescence sensor p-C4A can operate over a concentration range of 5–170 nM for Li+ sensing and 5–80 nM for PO43− sensing. The R2 values obtained for the sensing of Li+ and PO43− ions are 0.9962 and 0.9911, respectively. p-C4A demonstrates a minimum detection limit of 6.15 nM for Li+ and 9.0 nM for PO43−. The quantum yields of p-C4A as its Li+ and PO43− ion complexes were found to be 0.014 and 0.27, respectively. Herein, we report an easy-to-use, low-cost, disposable, paper-based, fluorescent, wax-printed device for the rapid chemical screening of Li+ and PO43−. This device can be used as a quick, portable, multiple-test panel that is simple, lightweight, and disposable. Moreover, in order to assess its analytical applicability, the prepared sensor was successfully used for the determination of Li+ and PO43− from wastewater samples, validating the proposed ion recovery method with 96–99% recovery rates. [ABSTRACT FROM AUTHOR]

Exosomes are vesicles released by healthy and cancer cells into the extracellular matrix and bodily fluid. Cancer cell-derived exosomes have attracted much attention in early-stage detection and prognostication of treatment response. Thus, detecting exosomes is of great interest to biology and medicine. However, many conventional detection methods require high-cost equipment and centralized laboratory facilities, making diagnostics inaccessible in limited-resource settings. This study reports a proof-of-concept low-cost electrochemical paper-based analytical device to quantify both the total bulk and cancer cell-derived exosomes in cell culture media. The device employs a sandwich immune assay design, where exosomes are initially captured using the electrode-bound generic antibodies (i.e. CD9) and subsequently detected via ovarian cancer-specific CA125 antibodies. Our proposed device quantifies the total bulk exosome concentration with a detection limit of 9.3 × 107 exosomes per mL and ovarian cancer cell-derived exosomes with a detection limit of 7.1 × 108 exosomes per mL, with a relative standard deviation of <10% (n = 3). We suggest that this low-cost and simple electrochemical paper-based device could be an alternative tool for detecting disease-specific exosomes in biological samples with the potential to be further developed for point-of-care diagnosis. [ABSTRACT FROM AUTHOR]

A direct mass spectrometry method utilizing reactive paper spray ionization was developed for sensitive cannabinoid quantitation in biofluid matrices. The ca. 2-minute sample measurements used on-paper derivatization to significantly increase paper spray mass spectrometry (PS-MS) positive ion mode sensitivity while minimizing sample preparation steps. Calibrations demonstrate high linearity, with R2 > 0.99 for (−)-trans-Δ9-tetrahydrocannabinol (THC) in oral fluid and 11-nor-9-carboxy-Δ9-tetrahydrocannabinol (THC-COOH) in urine. The limit of detection and lower limit of quantitation were 0.78 and 10 ng mL−1 for THC in oral fluid and 1.3 and 10 ng mL−1 for THC-COOH in urine, respectively. THC-COOH levels measured by reactive PS-MS in seven spiked human urine samples showed bias of −9.4 to 5.9%, and percent difference values of −16.8 to 9.8% in comparison with a reference LC-MS method. Based upon the method simplicity, validation experiments, sensitivity, and rapidity, we conclude that reactive PS-MS has potential applications for rapid cannabinoid drug testing in urine and oral fluid. [ABSTRACT FROM AUTHOR]

tert-Butylhydroquinone (TBHQ) residues in foods pose a threat to human health. Therefore, it is necessary to develop a rapid method for TBHQ detection. In this study, a sensitive monoclonal antibody 5C3 (IgG2a subclass) against TBHQ was produced. It possessed a half maximal inhibitory concentration of 7.43 ng mL−1. A gold nanoparticle-based immunochromatographic assay (ICA) was established for the rapid and sensitive screening of TBHQ in soybean oil. Qualitative analysis results were obtained within 10 min and observed with the naked eye. The visual limit of detection (LOD) was 50 ng g−1 and the cut-off value was 1000 ng g−1. A hand-held strip reader was used for quantitative analysis, in which the calculated LOD was defined as 18.68 ng g−1. The average recoveries of TBHQ ranged from 89.55% ± 2.70% to 100.66% ± 3.02% for soybean oil, with a coefficient of variation of 2.89%–7.05%. Therefore, our developed ICA is a useful tool for the rapid and on-site detection of TBHQ in real food samples. [ABSTRACT FROM AUTHOR]

One of the primary challenges for the development of electrochemical sensors for dopamine (DA) is the lack of selectivity due to the major interference from ascorbic acid (AA) which is oxidized at a potential close to the working potential of DA. In this work, we present a means for simple and cost-effective electrochemical detection of DA in the presence of interference using a microfluidic paper-based analytical device (eμPAD) to improve the selectivity and sensitivity. The device was made by incorporating the sample separation and the electrochemical detection elements into a single device, which required a single drop of the sample solution. For sample separation, Nafion was cast on the sample zone and microfluidic channel to block AA, before the solution was allowed to continuously flow to the detection zone. A multilayered eμPAD was fabricated by placing a round cotton pad on the detection zone to enable the generation of a quasi-steady flow rate. Thereafter, a packing tape was used to seal the top part of the device to increase the flow rate and prevent volatilization of the sample on the eμPAD. The concentration of DA that could be measured by the poly(glutamic acid) modified screen-printed graphene electrode was in the range of 1–200 μM, and the limit of detection (LOD) was 0.41 μM (3SD/slope). The proposed platform provides an accurate and satisfactory method for the detection of DA in real samples compared with UV-Vis spectroscopy. [ABSTRACT FROM AUTHOR]

We report for the first time a highly sensitive and rapid quantitative method for the detection of Salmonella Typhimurium (S. Typhimurium) using a conductive immunosensor on a paper-based device (PAD). S. Typhimurium monoclonal antibodies (MA) were first immobilized on a paper-based device and then captured by S. Typhimurium. After an immunoreaction on the device, the polyclonal antibody-colloidal gold conjugate (PA-AuNPs) was dropped to bind with S. Typhimurium. After a complete sandwich reaction, a dark red color appeared on the paper-based device, which can be observed by the naked eye for a rapid screening test. The electrical conductivity of PA-AuNPs between the screen-printed electrodes on the paper-based device was also measured for an accurate quantitative analysis. The electrical conductivity correlated well with the concentration of S. Typhimurium, which was controlled by the amount of S. Typhimurium attached to the polyclonal antibody-colloidal gold conjugate. The device showed a linear correlation for the concentration of the S. Typhimurium in the range of 10–108 CFU mL−1 in a logarithmic plot, with an R2 value of 0.9882 and a limit of detection (LOD) as low as 10 CFU mL−1. This simple, highly sensitive, and rapid method for the S. Typhimurium detection was successfully performed within 30 min, and it can be developed into small portable measuring devices in order to facilitate preliminary screening tests. [ABSTRACT FROM AUTHOR]

A microfluidic paper-based analytical method is developed for determination of Hg(II) using gold nanoparticles functionalized with N,N′-bis(2-hydroxyethyl)dithiooxamide. Fabrication of the μPAD in this work is free of any expensive equipment and could be performed by untrained personnel. The color of modified AuNPs in the test zone instantly changes after addition of Hg(II), and this color change can be detected by the naked eye, or a digital camera. Under optimized experimental conditions, the linear range is 0.020–8.0 μM of Hg(II) with 12.5 nM (2.5 ppb) detection limit in aqueous solution. In the case of the μPAD, the linear concentration range is 0.025–2.0 μM Hg(II) with a detection limit of 15 nM (3.0 ppb). This method is used for the determination of mercury in real samples such as salmon fish and dusty days in Sanandaj, Iran. The results determined by this method agreed well with those determined according to the ASTM standard method. [ABSTRACT FROM AUTHOR]

In this study, we describe the design and successful synthesis of a new hapten, which we used to prepare an anti-zilpaterol mouse monoclonal antibody (mAb) with an IC50 of 0.31 ng mL−1 and a limit of detection (LOD) of 0.02 ng mL−1. A colloidal gold immunochromatographic test strip was further developed and optimized using the antibody, and cross-reactivity experiments were carried out to prove its good specificity. Semi-quantitative and quantitative detections of zilpaterol were evaluated in swine urine and pork samples using the test strips. For semi-quantitative detection in swine urine and pork samples, the visual limit of detection values were 0.5 μg kg−1 and 0.5 μg kg−1, and the cut-off values were 5 μg kg−1 and 5 μg kg−1, respectively. For quantitative detection, the calculated limit of detection values were 0.08 μg kg−1 and 0.12 μg kg−1, and the remaining values were 10 μg kg−1 and 10 μg kg−1. The developed gold nanoparticle-based immunochromatographic assay is highly suitable for on-site detection and rapid preliminary screening of zilpaterol in swine urine and pork samples. [ABSTRACT FROM AUTHOR]

Here, we present a new diacetoxy-functionalized UiO-66 metal–organic framework (MOF) for the trace level detection of hydrazine in water. The MOF material (1) was solvothermally prepared by the reaction between ZrOCl2·8H2O and 2,5-diacetoxy-1,4-benzenedicarboxylic acid (H2BDC–(OCOCH3)2). The desolvated material (1′) showed a highly selective fluorescent turn-on signal towards hydrazine in water, which can be visualized by the naked eye under a UV lamp. Within 1 min of hydrazine addition, there was 14-fold fluorescence enhancement. The probe can detect hydrazine up to the nanomolar level (detection limit = 78.8 nM) in water. This detection limit is the lowest among MOF-based fluorescent probes for hydrazine. The material was also utilized for the sensing of hydrazine in paper strips and environmental water samples. Hydrazine-selective deprotection of ester groups anchored with the ligand is the principal reason behind the switch-on nature of sensing. [ABSTRACT FROM AUTHOR]

The monosaccharide 1,5-anhydroglucitol (1,5-AG) is a known indicator of glucose levels. Conventional 1,5-AG quantification methods with enzyme-based sensors using pyranose oxidase (PROD) require elimination of interference from the sample (a laborious and time-consuming process), as PROD cannot distinguish 1,5-AG from other sugars. We developed a one-step paper-based sensor for detecting 1,5-AG using glucose oxidase, catalase, and mutarotase that eliminates excess glucose, which interferes with 1,5-AG detection. This sensor consists of two compartments for the quantification of glucose and 1,5-AG and reflects the concentration of these targets after reaction with water or spiked human urine. The limit of detection of the sensor was 0.9 mg dL−1 for glucose and 3.2 μg mL−1 for 1,5-AG. [ABSTRACT FROM AUTHOR]

In the present article we report a new hybrid microfluidic device (hyFlow) comprising a disposable paper electrode and a three-dimensional (3D) printed plastic chip for the electrochemical detection of a magnetic bead–silver nanoparticle (MB–AgNP) bioconjugate. This hybrid device evolved due to the difficulty of incorporating micron-scale MBs into paper-only fluidic devices. Specifically, paper fluidic devices can entrap MB-containing conjugates within their cellulose or nitrocellulose fiber matrix. The hyFlow system was designed to minimize such issues and transport MB conjugates more efficiently to the electrochemical detection zone of the device. The hyFlow system retains the benefit of fluid transport by pressure-driven flow, however, no pump is required for its operation. The hyFlow device is capable of detecting either pre-formed MB–AgNP conjugates or conjugates formed in situ. The detection limit of AgNPs using this device is 12 pM, which represents just 22 AgNPs per MB. [ABSTRACT FROM AUTHOR]

A novel platform of microfluidic paper-based analytical devices (μPADs) for dual detection of bisphenol A (BPA), a model analyte, was fabricated using an electronic digital plotter to create the stacked layer of μPADs and generate the lateral-flow channel without using an external pump. Two detection techniques, including electrochemical detection and laser desorption ionization mass spectrometric detection (LDI-MS), were used complementarily to improve the precision in the detection of BPA. The fluid sample was delivered to both detection zones by the capillary action, automatically generated from the fabricated microfluidic device. For an electrochemical sensor, two ballpoint pens filled with silver nanoparticles (AgNPs) and multiwall carbon nanotube (MWCNT) ink were used to print onto the paper with a contact printing method using a digital plotter. To further improve the sensitivity, zinc oxide (ZnO) was used to modify both electrochemical and LDI-MS detection zones. For BPA detection, high electrocatalytic properties and strong UV absorption of ZnO promote the electron transfer in the electrochemical sensor and ionization efficiency in LDI-MS with low interferences compared with a conventional organic matrix. Under optimal conditions, this platform showed a dual detection capability for BPA with a detection limit of 0.35 μM for electrochemical detection and with an ultralow detection limit of 0.01 pM for LDI-MS. This novel platform might be very useful for trace analyses requiring high precision detection of various analytes. [ABSTRACT FROM AUTHOR]

This communication describes the rational design of a transparent paper-based chemosensing platform for multi-target detection by wavelength-dependent absorbance/transmittance. The platform was successfully applied in the examination of bovine serum albumin (BSA) and cholesterol in serum with a low detection limit of 0.1 μM and 0.1 mM, respectively. With low cost and high sensitivity, the paper-based platform shows great promise for multiplexed bioassays. [ABSTRACT FROM AUTHOR]

An increasing number of patients are living with Alzheimer's disease (AD); thus, the need for a method to detect AD early and sensitively has become urgent, and the demand for an intelligent analytical platform is growing year by year. Abnormal levels of acetylcholinesterase (AChE) and butyrylcholinesterase (BChE) are known to be indicative of AD. In this work, a novel conjugated polythiophene (CP) compound was successfully combined with CdTe quantum dots (QDs) to improve their selectivity and sensitivity. The QDs successfully enabled the detection of low concentrations of AChE by turning on the fluorescence of the CdTe/CP via the interaction between CP and thiocholine produced by ATCh hydrolysis and aggregation induced emission enhancement (AIEE). Under optimal conditions, we reached a low detection limit of 0.14 U L−1, which is 7.9 times lower than that of pristine QDs. More importantly, an efficient, inexpensive, and disposable paper-based platform, which allows the efficient visual detection of AChE activity via the color variation of CdTe/CP, was designed. Moreover, the accuracy of the method was demonstrated by conducting a recovery test in human serum, in which the recoveries reached 107% and 110%, proving that CdTe/CP has considerable potential to be used for analyzing real biological samples. The advantages of this method are its simplicity, fast detection capability, affordability, and the fact that it can be used for on-site detection of AChE activity. Furthermore, it has certain guiding significance for detecting AD. [ABSTRACT FROM AUTHOR]

A fluorescent probe for the colorimetric detection of cysteine (Cys) was synthesized by combining resorufin with 7-nitrobenzofurazan. The resultant probe was characterized by FT-IR spectroscopy, fluorescence detection, mass spectrometry and NMR spectroscopy. After reacting with Cys, resorufin is released and the color changes from light yellow to red on paper-based analytical devices. The results were recorded using a common cell phone and subsequently analyzed using Photoshop software. The color intensity of the RGB channel increased linearly in the 0.04 to 70.04 μM Cys concentration range when the probe concentration was 2.6 mM (R = 0.9965), and the limit of detection was 16 nM. The effects of detection conditions have been investigated and are discussed. The interference deviations of 13 substances to Cys were in the range of −2% to +2%. The Cys concentration was determined as 270.8 ± 19.3 μM in human plasma, and the recovery was from 99.7% to 100.4%. The work demonstrates the potential of the method to detect Cys in real samples with low cost and high sensitivity. [ABSTRACT FROM AUTHOR]

A supramolecular complex of syn-(methyl,methyl)bimane (1) and β-cyclodextrin demonstrates a sensitive (limit of detection = 0.60 nM) and selective fluorescence turn-off response in the presence of cobalt in aqueous media, with calibration curves enabling quantitation in solution and using filter papers on which bimane and cyclodextrin were adsorbed. 1H NMR spectroscopy provides insight into interactions underlying the sensor performance. [ABSTRACT FROM AUTHOR]

The first discrete bimetallic europium(III)/copper(II) complex for the fast, sensitive and selective luminescent detection of both aqueous and gaseous hydrogen sulfide has been developed. The chemosensor displayed an impressive response time of 30 seconds and a low theoretical limit of detection (100 ppb) for gaseous hydrogen sulfide. [ABSTRACT FROM AUTHOR]

A luminescent trimethylamine (TMA) sensor, PTMA-Ir, has been designed and synthesized through immobilizing a phosphorescent iridium(III) complex on a TMA-imprinted polymer. Detailed study shows that the quenching of phosphorescence of PTMA-Ir can serve as a reporter for the binding of TMA on the imprinting sites, thus providing a sensitive, selective, and rapid detection of TMA in both aqueous solutions and gaseous states. Loading PTMA-Ir on filter paper produced a deposition T-Ir, the phosphorescence of which is quenched within 5 s upon exposure to TMA vapor with detection limits of 9.0 ± 0.1 ppm under argon and 15.0 ± 0.1 ppm in an air atmosphere. This work provided an effective method for establishing an imprinting polymer-immobilized luminescent amine sensor. [ABSTRACT FROM AUTHOR]

We propose a novel microfluidic paper-based phosphorus-detection chip (μPPC) for rapid analysis of trichlorfon, one of the most common organophosphate pesticide residues. The semi-quantification method was established and the limit of detection was 1.65 μg mL−1. We believe that the μPPCs could be a promising approach for the rapid determination of organophosphate pesticides. [ABSTRACT FROM AUTHOR]

4-Aminophenol (4-AP) is a highly toxic environmental pollutant and contaminant of medicine, which is widely used in industries and daily life. Therefore, the development of a reliable sensor for determining the amount of 4-AP is of great importance for the protection of human and environmental health. Herein, by fabricating a Pd@CeO2 composite on a nanoporous gold-coated carbon fiber paper (NPG/CFP), the sensing properties for 4-AP can be largely enhanced. Combining the significant increase in the catalytic activity of the Pd@CeO2 composite (derived from the strong interactions between Pd and CeO2) with the NPG and NPG/CFP hierarchical porous structure having a high electrochemically active surface area, the electrode achieved excellent detection of 4-AP. It manifested an extremely high sensitivity of 75.4 μA μM−1 and 56.5 μA μM−1 in the concentration range from 0.005 μM to 0.03 μM and 0.03 μM to 9 μM, respectively. The detection limit reached as low as 4 nM under optimized conditions (S/N = 3). The electrode also possesses long-term stability and presents great anti-interference ability. All these results demonstrate that the electrode is a promising candidate for future sensors for monitoring 4-AP in water and pharmaceuticals. [ABSTRACT FROM AUTHOR]

In this paper, Tesla coil discharge (TCD) was combined with laser-induced breakdown spectroscopy (LIBS). The TCD successfully enhanced the emission of Al atomic lines and AlO molecular bands in Al LIBS, and improved the sensitivity of quantitative analysis of Cr and Pb elements detected by LIBS in water. Firstly, the paper explored the effect of the distance from the TCD tip to the sample surface on the emission of Al atomic lines and AlO molecular bands, finding that 5 mm was the optimal distance. Secondly, the paper investigated the effect of laser energy on the emission of Al atomic lines and AlO molecular bands, finding that 25.1 mJ was the optimal laser energy. Finally, the paper constructed the calibration curves of Cr and Pb elements in water and calculated the limit of detection (LoD), finding that compared with surface enhanced LIBS (SELIBS), TCD–SELIBS reduced the LoDs of Cr and Pb elements from 16.7 ng mL−1 and 12.2 ng mL−1 to 7.3 ng mL−1 and 5.5 ng mL−1, respectively. It indicated that the combination of TCD and SELIBS can achieve high-sensitivity detection of Cr and Pb elements in the water. The combination of TCD and LIBS is a simple, low-cost, easy-to-operate, industrialized and commercialized technology, and has a promising application prospect in the high-sensitivity analysis of heavy metals in water. [ABSTRACT FROM AUTHOR]

Metal–organic frameworks (MOFs) have unique potential in the field of gas sensing due to their ultra-high specific surface area and abundant mesoporous structure. In this paper, a mesoporous Co3O4 hollow polyhedron structure with high specific surface area (141.6 m2 g−1) was synthesized by annealing at the optimum temperature. The gas response of the mesoporous Co3O4 hollow polyhedron structure to volatile organic compounds such as xylene, ethanol, methanol and acetone was systematically tested. The experimental results show that the mesoporous Co3O4 hollow polyhedron structure has the highest sensitivity (21.33) and excellent stability for xylene gas, and the detection limit is low (1 ppm). The excellent sensing performance benefits from large surface area, high oxygen defect concentration and mesoporous structure. [ABSTRACT FROM AUTHOR]

In this paper, we report on the development of an 'off–on' fluorescent probe for the detection of hydrogen peroxide (H2O2) and mercury ions (Hg2+) using an in situ synthesized carbon quantum dot and gum Arabic silver nanoparticle composite (CQDs@GA-Ag NPs). Electron microscopy measurement clearly shows that CQDs are attached to the surface of the GA-Ag NPs. The fluorescence intensity of the CQDs was dramatically quenched in the synthesized nanocomposite via the inner filter effect (IFE) mechanism. After adding H2O2 to the nanocomposite system, the Ag NPs got oxidized leading to the formation of Ag+ ions, and the CQDs regained their photoluminescence (PL) property. This facilitates the detection of H2O2 with an extremely low detection limit of 1.02 μM. Furthermore, the as-developed nanocomposite was also tested for the detection of Hg2+ ions, obtaining a remarkably low detection limit of 1.82 μM. The developed probe was extremely selective over a wide range of interfering ions and substances. [ABSTRACT FROM AUTHOR]

A volumetric bar-chart chip (V-chip) is a microfluidic device based on distance-based quantitative measurement that visualizes analyte concentration without the need for apparatus or data processing. This typically utilizes special receptors and catalysis parts that generate oxygen, so ink can be moved inside the channels, and enables instant visual quantitation of the analyte. However, the low stability of some macromolecules, the use of expensive catalysts, and difficulty in controlling the process cause inaccurate readings, and therefore, limit further development and the use of these systems. In this article, we introduced a novel approach that eliminates the use of catalysts in V-chips and provides an efficient and simple path in the design of biosensors. The product of the enzymatic reaction of urease with urea is bicarbonate, which turns into CO2 gas in an acidic environment. Therefore, the amount of gas produced is proportional to the amount of urea in the sample, and it can be quantitatively measured by visual detection from the amount of ink movement caused by CO2 gas pressure. This biosensor has a linear response range of 0 to 1000 µg ml-1 and a detection limit of 3.6 µg ml-1 in raw milk. The recovery of urea in raw milk at 100 and 400 µg ml-1 concentrations was 96.5% and 98.9%, respectively. This volumetric chip shows potential for determining urea levels in real samples without requiring additional equipment. The combination of the sensitivity and specificity of enzymatic reactions, inherent gas-generating reactions, and the processability of microchips discussed in this paper can be the basis for the comprehensive development of volumetric chips, which can create a new path for the development of efficient and cheap biosensors. [ABSTRACT FROM AUTHOR]

A europium-functionalized, dual-emissive, metal–organic framework-based fluorescence sensor (EuUCNDA) was constructed via post-synthetic modification of an UiO-66-type precursor through coordination interactions. EuUCNDA exhibited extremely high selectivity and sensitivity for malachite green (MG) with a low detection limit of 13.01 nM, a wide linear concentration range (0.05–50 μM), excellent anti-interference properties, a rapid response (<1 min), and the possibility of recycling. The good sensing performance of EuUCNDA enables the practical detection of MG in fish pond water and grass carp with good recoveries. Moreover, EuUCNDA can be reused for sensing MG and over 90% of fluorescence intensity can be restored after 7 cycles. Furthermore, EuUCNDA-embedded paper-based sensors combined with smartphone imaging afford portable and visual monitoring of MG in real samples. Notably, besides good sensing performance, EuUCNDA could efficiently remove MG from water. Hence, this work provides a recyclable and sensitive fluorescence sensor for portable, visual, rapid detection and efficient removal of MG. [ABSTRACT FROM AUTHOR]

Sensitive detection of glucose is important for public health, but non-enzymatic glucose biosensors still face significant challenges. In this paper, a novel and sensitive non-enzymatic glucose sensor was developed by in situ preparation of CuO nanorod-supported NiCo LDH nanosheet arrays on copper foam (CuO@NiCo LDH NSAs/CF). Because the hierarchical core–shell nanostructure provides more active sites and increases the exposed surface area of the catalyst, the catalytic activity of the electrode was significantly increased. As a working electrode, the CuO@NiCo LDH NSAs/CF catalyst showed good glucose sensing performance in a linear range of 0.6 μM–3 mM and a detection limit of 0.16 μM (S/N = 3). The sensor also showed repeatable responses over a month with negligible interference, and satisfactory recoveries with real human serum samples. [ABSTRACT FROM AUTHOR]

Hypochlorite (ClO−) is closely involved in human health and environmental safety. Therefore, it is of vital importance to realize the detection and separation of ClO−. Herein, a nanoprobe with analysis and removal capabilities of ClO− was synthesized via immobilizing coumarin-based functional molecules on halloysite nanotubes. The probe can easily detect ClO− in aqueous solution without the need for organic solvents, showing a fast detection time (10 s), a wide pH range (4–11), a low detection limit (8.4 nM), and a credible recovery rate range of 93.6–105.1%. The probe was further prepared into convenient test papers to realize the visual detection of ClO−. More importantly, it also enabled the removal of ClO−, and the removal rate was as high as 99.6%. [ABSTRACT FROM AUTHOR]

Environmental water pollution caused by hexavalent chromium (Cr(VI)) is a threat to living beings due to its carcinogenic nature. Herein, we report the synthesis of a highly fluorescent water-soluble conjugated polyelectrolyte PPMI and its application as a fluorescence sensor to monitor traces of carcinogenic Cr(VI) ions in water. PPMI was synthesized via the oxidative polymerization method followed by post-polymer functionalization. Fluorescent PPMI exhibited a photoluminescence quantum yield of 23.87 and displayed a rapid, very selective, and sensitive turn-off fluorescence signal in response to Cr(VI), with a significantly high quenching constant of 1.32 × 106 M−1. The mechanism of sensing was found to be static quenching. The limit of detection of this highly accessible analytical method was found to be in nanomolar ranges, i.e. 0.85 nM. Additionally, sensing on solid platforms such as economical paper strips was successfully achieved, which is very challenging and highly recommended for any reliable, portable, and economical analytical method. [ABSTRACT FROM AUTHOR]

The development of sensors with high sensitivity, selectivity, long-term stability and other excellent performances is still the focus of current research on gas sensors. In this paper, biomorphic zinc oxide composite reduced graphene oxide nanomaterials (C–Z–ZnO–rGO) based on a metal–organic framework are synthesized by an impregnation calcination method using cotton as a biological template. The microscopic morphologies and structural composition of the composites are characterized. The response value of C–Z–ZnO–rGO to acetic acid gas is much higher than that of other gas sensors. At an operating temperature of 350 °C, the C–Z–ZnO–rGO gas-sensitive sensors have a response value of 410 for 100 ppm acetic acid, a response time of 43 s, and a recovery time of 18 s, and have good repeatability and long-term stability. The response value of 2.614 for 1 ppm of acetic acid gas further indicates that the C–Z–ZnO–rGO sensor has a low detection limit. The hollow structure of the C–Z–ZnO–rGO composites has the advantages of high specific surface area, multiple pores, diverse structures and abundant active sites, which improves the adsorption performance on acetic acid gas. [ABSTRACT FROM AUTHOR]

Development of an effective and convenient sensor for sensitive detection of nitrites is of great concern since excessive amounts of nitrites can be harmful to both human health and the environment. In this work, Cu-MOF modified exfoliated graphite paper (EGP) was employed as a signal reporter to enable the visual and electrochemical dual-mode sensing of nitrites. Cu-MOFs were in situ synthesized on EGP, which exhibited an excellent oxidase enzyme-like activity to oxidize 3,3′,5,5′-tetramethylbenzidine (TMB) into its oxidation product (oxTMB). The multi-layer structure and the superior electrical conductivity of EGP not only facilitated the loading of the Cu-MOF nanozyme for colorimetric sensing but also enabled its use as an underlying backbone to support electroanalysis. Based on the recognition of nitrite through a highly specific diazo reaction between nitrite and oxTMB, the addition of nitrite caused the colorimetric sensing solution to change color from blue to green, which allowed for the colorimetric sensing of nitrite with a limit of detection (LOD) of 8.5 × 10−6 mol L−1. Meanwhile, the Cu-MOF/EGP electrochemical platform was employed for ratiometric detection of nitrite based on the electrochemical oxidation of nitrite and TMB. Compared with the colorimetric mode, the electrochemical mode possessed higher sensitivity with a LOD of 5.4 × 10−7 mol L−1, indicating the high sensitivity and accuracy of the proposed dual-mode sensing strategy. Furthermore, the determination of nitrite in different pickled food samples is demonstrated. [ABSTRACT FROM AUTHOR]

A ultrasensitive NiFeP based electrochemical sensor was developed for the selective electrochemical detection of dopamine to address the issue associated with neurological disorders including Parkinson's and Alzheimer's diseases. The novel sensor shows superior selectivity and sensitivity with a lowest detection limit of 0.3 nM and a wide detection range of 10 nM–500 μM and is immune to the interference of ascorbic acid at physiological pH (7.4). A novel flexible sensor was developed with NiFeP coated over Whatman filter paper, which exhibits two liner ranges of 10 nM−1 μM and 10 μM–500 μM with an ultra high sensitivity of 756 μA μM−1 cm−2 and 4.6 μA μM−1 cm−2 respectively with a wide detection range of 10 nM to 500 μM. [ABSTRACT FROM AUTHOR]

The development of a rapid and selective method for the identification of dipicolinic acid (DPA), a specific biomarker in Bacillus anthracis spores, is of great importance for the avoidance of anthrax infection. Herein, a chain-based EuIII metal–organic framework with the formula {[Eu3(BTDB)3(μ3-OH)3(H2O)]·solvents}n (JXUST-38, H2BTDB = (benzo[c][1,2,5]thiadiazole-4,7-diyl)dibenzoic acid) was obtained using 2-fluorobenzoic acid as the pH regulator. JXUST-38 exhibits good chemical and thermal stability and can specifically recognize DPA in N,N-dimethylformamide solution through luminescence enhancement and blue-shift effects with a detection limit of 0.05 μM. Furthermore, the significant luminescence enhancement and blue shift under UV lamps are obviously observable by the naked eye. The luminescence sensing mechanism is attributed to absorbance-induced enhancement between JXUST-38 and DPA. Test paper and mixed-matrix membrane based on JXUST-38 are designed for DPA detection. In addition, the feasibility of using JXUST-38 in biosensing is discussed in detail. [ABSTRACT FROM AUTHOR]

In recent years, the development of new scintillation materials with red and near-infrared light emission has had significant advantages based on the development of an avalanche photodiode with high quantum yield. This study used a hydrothermal method to synthesize rare-earth-doped Cs2NaScCl6 crystals, in which a red emission of Cs2NaScCl6:Sm was investigated with high X-ray sensitivity and low detection limit. In addition, a tunable wavelength range of radioluminescence can be achieved, in which a near-white light emission can be generated by precisely controlling the proportion of Sm3+ and Tb3+ doping concentrations. Meanwhile, a Cs2NaScCl6:7%Sm scintillation film has been successfully prepared by direct coating with a thickness of 150 μm, which achieves a spatial resolution of 11.9 lp mm−1 based on X-ray imaging experiments. Therefore, this perovskite material has shown potential application as an eco-friendly multifunctional imaging material. [ABSTRACT FROM AUTHOR]

This paper introduces an enclosed microfluidic chip that integrates sample preparation and the chamber-based digital polymerase chain reaction (cdPCR). The sample preparation of the chip includes nucleic acid extraction and purification based on magnetic beads, which adsorb nucleic acids by moving around the reaction chambers to complete the reactions including lysis, washing, and elution. The cdPCR area of the chip consists of tens of thousands of regularly arranged microchambers. After the sample preparation processes are completed, the purified nucleic acid can be directly introduced into the microchambers for amplification and detection on the chip. The nucleic acid extraction performance and digital quantification performance of the system were examined using synthetic SARS-CoV-2 plasmid templates at concentrations ranging from 101–105 copies per μL. Further on, a simulated clinical sample was used to test the system, and the integrated chip was able to accurately detect SARS-CoV-2 virus particle samples doped with interference (saliva) with a detection limit of 10 copies per μL. This integrated system could provide a promising tool for point-of-care testing of pathogenic infections. [ABSTRACT FROM AUTHOR]

In this work, a simple and sensitive colorimetric fluorescence sensing probe was designed for the detection of uric acid (UA). UA can quench the fluorescence emission of CsPbBr3via hydrogen-bonding interactions. The probe can directly detect UA with an ultralow detection limit of 62.7 ppb and a fast response time of 30 s in a linear range of 0.0031–1.33 μM. The designed sensor displays a gradual color change from green to blue upon conjugation with UA. The applicability of the proposed sensor was also investigated as a paper sensor probe for detecting UA. Further, the method was successfully applied for the detection of UA in human blood serum. This work proposes CsPbBr3 as a novel platform for detecting UA well in clinical diagnosis. [ABSTRACT FROM AUTHOR]

A novel three-dimensional Eu3+-based metal–organic framework with the formula {[(CH3)2NH2][Eu(BTDI)]·H2O·DMF}n (JXUST-25) was prepared by solvothermal method based on Eu3+ and 5,5′-(benzothiadiazole-4,7-diyl)diisophthalic acid (H4BTDI) with benzothiadiazole (BTD) luminescent groups. Due to the presence of Eu3+ and organic fluorescence ligand, JXUST-25 displays turn-on and blue-shift fluorescence toward Cr3+, Al3+ and Ga3+ with limits of detection (LOD) of 0.073, 0.006 and 0.030 ppm, respectively. Interestingly, the alkaline environment can change the fluorescence of JXUST-25 toward Cr3+/Al3+/Ga3+ and the addition of HCl solution realizes the reversible change of the fluorescence of JXUST-25 toward Cr3+/Al3+/Ga3+. It is noteworthy that the fluorescent test paper and light-emitting diode lamp based on JXUST-25 can effectively detect Cr3+, Al3+ and Ga3+ by the visual changes. In addition, the turn-on and blue-shift fluorescence between JXUST-25 and M3+ ions may be caused by the host–guest interaction and the absorbance caused enhancement mechanism. [ABSTRACT FROM AUTHOR]

In this paper, a novel fluorescent probe, TPA-PAT, with continuous recognition based on triphenylamine was designed, synthesized, and characterized by NMR, IR, and fluorescence spectrophotometry techniques. The research results showed that the probe could specifically recognize Cu2+ in DMSO/H2O (99:1, v/v) with a detection limit as low as 0.40 mM and a coordination ratio of 1: 2. On this basis, it was found that its complex TPA-PAT-Cu2+ could achieve a continuous progressive recognition of the anion S2- and amino acids GSH, L-His, and L-Gly, while simultaneously showing high sensitivity for them with low detection limits of 25.7, 18.9, 21.7, and 45.9 nM, respectively. The probe had good reversibility and could be recycled. In addition, the probe TPA-PAT could simultaneously recognize Cu2+ and Hg2+ in acetone/H2O (99:1, v/v) with detection limits of 0.16 and 0.20 mM, respectively, while their coordination ratios were 1: 2. Similarly, its complex TPA-PAT-Hg2+ was able to continuously recognize the amino acids Cys and GSH with detection limits of 0.34 and 0.29 mM, respectively. It was also found that the probe and its complexes were able to be prepared for convenient dipstick applications, which could achieve a rapid fluorescence response to anions and amino acids and suggested its very good application prospects. [ABSTRACT FROM AUTHOR]

A xanthene fluorophore-based probe, Xanth-NO2, has been reported for the detection of thiophenol. Xanth-NO2 exhibited quenched fluorescence in an aqueous buffer due to its aggregate state, which allows a fluorescence turn-on response via the PhSH-induced transetherification process. In an aqueous buffer, the half-time for the reaction of Xanth-NO2 with thiophenol is 15 min. There is a linear overlap between the Xanth-NO2 fluorescence and thiophenol concentrations (0–10 μM), with a 130 nM detection limit. Xanth-NO2 reacted differently with hydrogen sulfide and thiophenol, allowing us to distinguish between these two analytes. Additionally, the ability of Xanth-NO2 to detect thiophenol in the presence of competing molecules or ions was demonstrated. Real-water samples and paper strip-based vapour phase detection of thiophenol were used to show the potential use of the reported probe. [ABSTRACT FROM AUTHOR]

A novel water-stable CdII-based metal–organic framework, namely {[Cd(BIBT)(TDC)]·2H2O}n (JXUST-28, BIBT = 4,7-bi(1H-imidazol-1-yl)benzo-[2,1,3]thiadiazole and H2TDC = 2,5-thiophenedicarboxylic acid), was synthesized using a mixed-ligand strategy. Structural analysis demonstrates that JXUST-28 exhibits a two-dimensional layer structure with 4-connected sql topology. Intriguingly, JXUST-28 presents good stability in boiling water (at least 5 days), common organic solvents and aqueous solutions with different pH values of 2–12 (more than 24 hours). Furthermore, fluorescence experiments revealed that JXUST-28 could sense Hg2+ ions in aqueous solution via a quenching effect with a detection limit of 0.097 μM. Meanwhile, JXUST-28 can also be regenerated at least 5 times to detect Hg2+ ions. In addition, light-emitting diode lamps, luminescent films, and test papers of JXUST-28 have been successfully developed for practical applications. [ABSTRACT FROM AUTHOR]

Antibiotic abuse is considered a serious problem affecting human health, necessitating that great attention be paid to explore robust, simple and sensitive methods for rapid evaluation. In this paper, we developed a fluorescent aptasensor for visual and real-time kanamycin detection by taking advantage of the label-free strategy based on H-aggregate disassembly of a chiral cyanine dye induced by a G-quadruplex aptamer. The good sensitivity and selectivity enabled this aptasensor to have a detection limit as low as 43 nM and have high specificity for kanamycin recognition. Furthermore, this assay was successfully applied for the detection of kanamycin in lake water and urine with excellent recoveries. [ABSTRACT FROM AUTHOR]

In this article, a novel triphenylamine-modified salicylaldehyde Schiff base 2-(((4-(diphenylamino)phenyl)imino)methyl)-4-(pyridine-4-yl)phenol (HL) was synthesized and structurally characterized. HL possessed D–π-A structure and exhibited typical AIE property in THF/H2O. It was applied to selectively recognize Cu2+ through an on–off mode in THF/H2O (1/9, v/v), and the fluorescence attenuation was attributed to a paramagnetic quenching effect of Cu2+ together with the abatement of HL aggregates. Hence, the detection limit achieved was as low as 1.32 × 10−7 M. The spectroscopic and ESI-HRMS results revealed a 1 : 2 complexation ratio of Cu2+ with HL. The mechanism for sensing Cu2+ was further confirmed by performing DFT calculations. Owing to the large affinity between Cu2+ and His, the resultant CuL2 system was further used to detect His via the off–on method based on the displacement of ligands. The detection limit for His reached 5.14 × 10−8 M. Furthermore, HL was available to prepare handy indicator papers for the on-site recognition of Cu2+ and His. Confocal fluorescent imaging demonstrated that HL could sequentially respond to intracellular Cu2+ and His. [ABSTRACT FROM AUTHOR]