Search

Due to the long-term effect of the electric field and the heating from the conductor heating, many bubbles will precipitate on the surface of the oil-paper inside the bushing. When the bubbles move to the strong electric field, the partial discharge is caused, which seriously threatens the safe operation of the transformer hushing. Therefore, the conditions for bubble separation were analyzed based on the physical analysis of the liquid. The test platform for bubble observation inside the bushing oil-paper insulation was established, and lest samples with different water content were tested subsequently. The rapid heating method was employed to study the bubble generation over the oil-paper surface, and the variation of initial temperature of bubbles was obtained. The bubble initiation temperature between 0.5 °C/min and 5.5 °C/min was explored through experiments. The results show that the bubble initiation temperature differed by a maxi-mum of 30 °C at different temperature rise rated. When the rising rate is greater than 3 °C/min, the bubble initial temperature begin to decrease significantly; while when the temperature rising rale is less than 3 °C/min, the bubble generation initial temperature is more dispersive hut the result is normally distributed; When the moisture content increases, the initial temperature of bubble generation decreases significantly. When the moisture content increases from 2. 7% to 6. 8% , the initial temperature of the bubble drops by 44 °C. The research results have engineering application value for analyzing whether there are bubbles inside the bushing during operation, evaluating the internal insulation status of the transformer bushing, and ensuring the safe and stable operation of the power transformer. [ABSTRACT FROM AUTHOR]

《糖尿病足溃疡预防和管理的研究和论文质量评价标准：需要的基本内容和高质量的标 志》一文是由国际糖尿病足工作组和欧洲创面管理学会联合发表的1篇重要文献, 作为衡量已经发表 的糖尿病足溃疡的临床研究与论文质量的标准, 特别是2019国际糖尿病足预防与管理系列指南录选 引用论文的主要标准。文中强调糖尿病足临床研究设计、实施和结果报告及论文发表中需要注意的 问题, 并为糖尿病足溃疡临床研究与相关论文的科学质量评估提出了21条评分标准。笔者对此文进 行摘译和解读. [ABSTRACT FROM AUTHOR]

The porous characteristic of tlie paper substrate causes penetration and difusion of tlie li(_uid material on the surface. Therefore，it is extremely difficult to form an RFIDtag metal antenna by electroless deposition on the surface of the paper substrate. Aiming at this problem，the stannous chloride colloid solution \as applied to avoid the catalytic ink penetration in the paper - based substrate. Moreover， paper substrate was immersed in chitosan solu- tion， which could bring functional group and improve the conductivity and adhesion of RFID metal antenna. The SEM，XRD，EDS and adhesion test of the metal layer antenna of the RFID tag proved that the surface of the metal layer of tlie tag antenna had advantages including dense surface， high crystallinity， good adhesion， low resistivity (2.58X10-8 # + cm)，good mechanical properties (1000 bending test). [ABSTRACT FROM AUTHOR]

[Objective]The present paper aimed to search for some technical methods which could reduce the tar content of reconstituted tobacco effectively. [Method]The effect of some factors such as ratio of stems to leaves, beating degree, basis weight, coating rate, proportion of plus fiber and calcium carbonate on the tar content of paper-making reconstituted tobacco was studied and those factors that could reduce the tar content effectively had also been verified. [Result] (i)Beating degree, basis weight, proportion of plus fiber, potassium salt and calcium carbonate had significant influence on the tar content of paper-making reconstituted tobacco;(ii)The ratio of stems to leaves of raw materials also had a certain influence on the tar content of paper-making reconstituted tobacco, and the tar content was the lowest when the ratio of stems to leaves was 2-1;(iii)There was a positive correlation between the coating rate and the tar content of paper-making reconstituted tobacco, the increase of coating rate would lead to the increase of tar content.(IV) The tar content of paper-making reconstituted tobacco prepared under a set of factors, including fiber proportion, beating degree, basis weight had fallen by more than 50 % ,and blending it in cigarette products had also reduced the tar content of cigarettes obviously. [Conclusion] The tar content of reconstituted tobacco could be reduced by adjusting the process parameters. While the PRT sample integrated with some tar-reduced factors was blended into cigarettes, it could greatly reduce the tar content of cigarettes. Therefore, some technical methods could be taken properly to reduce the tar content of PRT, and achieve ‘ reducing the harmful and tar content’ after blending it into cigarettes. [ABSTRACT FROM AUTHOR]

TOCNs reinforced aramid-mica papers were fabricated by vacuum assisted filtration approach with aramicl fibricl and mica as tbe main materials and TEMPO oxidized nanocellulose (TOCNs) as reinforced material. The structure mechanism, mechanical performance, breakdown strength of the TOCNs reinforced aramid-mica papers with different contents of TOCNs were analyzed and compared. The results showed that,the addition of TOCNs could not only effectively strengthen the interfacial bond between aramid fiber and mica, but also could significantly reduce the structural defects in the papers. When the content of TOCNs was 20 wt. %,the tensile strength and the average breakdown strength of the TOCNs reinforced aramid-mica papers achieved 82% and 72% enhancement from the pristine paper, respectively. [ABSTRACT FROM AUTHOR]

In the early period of Yi Dynasty of Korea, currency and physical transactions were parallel, and the market order was chaotic. During the reign of Emperor Taejong, the Banknote Law was established and carried out, and measures such as replacing physical objects with paper money, establishing joint purchase houses and determining the crime of hiding cloth were adopted to enhance currency credit. Although the law promoted circulation, monetary reform was not smooth. In this study, based on the economic historical data of the dynasty and the game theory method, the author find that the Yi Dynasty tries to improve the relationship between the state and the grassroots society and explore new economic policies through national finance and monetary reform. The failure of monetary reform is not only a policy failure, but also a consequence of uneven distribution of interests among different subjects. [ABSTRACT FROM AUTHOR]

As a type of high performance inorganic fiber, basalt fiber exhibits excellent strength properties? high/low temperature resistance and chemical stability，which can be widely used in the field of construction and building materials, heat insulation and filtration. However,the poor dispersibility and paper strength of paper made of basalt fiber limit its ap­plication in paper industry. In this work，iltrafine basalt fiber was employed as material to in­vestigate the effect of pH of fiber suspension on fiber dispersion. In addition,the influence of the ratio of basalt fiber and unbleached electric insulation pulp on paper properties was also investigated. Results showed that the optimal fiber dispersion can be obtained when fiber suspension pH was 4. 38. And paper physical testing showed that the apparent density, tensile index and breakdown strength of basalt fiber/cellulosic fiber composite paper decreased with increasing basaltfibercontent.Whenbasaltfibercontentwaslower than 50 % ,the tensile strength of paper can satisfy the requirement of manufacturing. Therefore, the addition a­mount of basalt fiber depends on the requirement of paper properties and its application. [ABSTRACT FROM AUTHOR]

Objective: To analyze the bibliometric indicators of SCI papers in the field of pharmacy in China from 2010 to 2019 by Essential Science Indicators (ESI) and InCites databases, so as to know the status quo and development trend of pharmacy in China in the last decade. Methods: In search of papers from ESI and InCites databases, the publication time of papers for retrieval was set within the time span of 2010-2019, the research output location was "mainland China" and the research area was "pharmacology and pharmacy". Then，related SCI papers in the field of pharmacy contributed by researchers in mainland China from 2010 to 2019 were retrieved. Such vital data as publication years, specific journals, location of research institutions, international collaboration and funding for researches were analyzed statistically, and those papers with high influential impact were further retrieved and analyzed. Results: In the field of domestic pharmacy，a total of 81 679 SCI papers were published, including 13 720 international collaborative papers and 470 papers with high influential impact. The amount of SCI papers，the number of international collaborative papers and papers with high influential impact increased year by year. China had international collaboration with 129 countries or regions in the field of pharmacy，and 48 .49% of the papers were sponsored by domestic research funds. Conclusion: In recent 10 years, the scope of research in pharmacy at home has expanded gradually, academic influential impact has arisen steadily, and the number of international collaborative papers and papers with high influential impact has also increased quite noticeably. However, the quality of scientific papers as well as international collaboration demand further improvement. [ABSTRACT FROM AUTHOR]

[Objective] Feasibility study of applying writing paper as sealing materials in oyster mushroom’s cultivation was conducted in or¬der to provide theoretical basis for increasing the safety of oyster mushroomproducts. ' Method】 The experiments and production demonstration were carried out by setting 2 treatments, ie. treatment Awith writing paper as sealing materials and treatment Bwith newspapers! CK) ,and the growth of mycelium, number and fresh weight of fruiting bodies, cost and economic returns as well as heavy metal contents in fruiting bodies were investigated and evaluated. ' Result】 The growth rate of mycelium was 0. 97 cm/d of treatment A, which was significantly higher than that of treatment B (% < 0 . 05 , the same as below), and the average number and fresh weight of fruiting bodies per bag (total of the first flush and second flush, hereafter) were 43.47 ,257. 59 g,5. 57 more and 11 . 7 g higher than that of treatment B, respectively. The results showed that the heavy metal content of Pb, Cd, Hg and As in fruiting bodies of both treatment A and Bwas lower than the limits (1 . 000, 0. 200 ,0. 100,0. 500 mg/kg, respectively) set by both national food safety ytandard and national aaricultural standard for green food mush¬ room, and the content of Pb, Cd, Hg, As of treatment A was only 0. 001, 0. 085 , 0.002 and 0. 037 mg/kg, which was far more lower tlian the safety limits mentioned above, respectively. Besides, Cr was not found in the fruiting bodies of treatment A. The results indicated that the oyster mushroom of treatment A was much safer than that of treatment B. Compared to treatment B， the cost per bag of sealing materials and their processing increased by 0.002 yuan， while the output valiae increased by 0. 140 yuan, thus the eco¬nomic retiams per bag of treatment A was 0. 138 yuan higher than that of treatment B. The results of production demonstra¬tion showed that，when compared witli treatment B，treatment A could shorten the period of spawn running by 3 days and shorten the average harvesting time of the first and second flush by 3 and 4 days, respectively, besides, treatment Acould increase thefresh weight per bag by 24. 00 gin total. ' Conclusion】 Based on the in¬crease of mycelium ’ s growth rate, number and fresh weight of fruiting bodies, economic returns, as well as decrease of heavy metal contents, it is recommended that writing paper could be applied instead of newspapers as sealing materials in oyster mushroom5 s production [ABSTRACT FROM AUTHOR]

The single-factor experiment was used to investigate the effect of filter wrap' s air permeability, tipping paper's air permeability, and perforation row number on the filter ventilation rate of the cigarette. Furthermore, the effects of three factors and their interaction on the filter ventilation rate of the cigarette and the chemical composition of mainstream smoke by split-plot experiment were analyzed. The results showed that the filter ventilation rate of the cigarette increased with the increase of tipping paper's air permeability or perforation row number in single-factor experiment and split-plot experiment. In the range of 3300 ~ 8000 CU, the effect of the permeability of the formed paper on the ventilation rate of the cigarette filter was significant. After exceeding 8000 CU, the effect of filter wrap's air permeability on the filter ventilation rate of the cigarette decreased. The three factors of filter wrap's air permeability, tipping paper's air permeability, and perforation row number had significant interactions, which could coordinately adjust the filter ventilation rate of cigarette. With the increase of the filter wrap's air permeability, tipping paper's air permeability, and perforation row number, the content of nicotine, tar and COin the mainstream smoke of cigarette decreased. According to actual needs, the filter wrap's air permeability was 8000 CU, tipping paper's air permeability was 250 CU, and perforation row number was 3, which could reduce the content of nicotine, tar and CO in the cigarette smoke, and reduce the loss of smoke aroma. [ABSTRACT FROM AUTHOR]

Although Dietrich BonhocfYer’s Wider stand und Ergehung. Briefe und Aufzeichnungen aus der Haft (Letters and Papers from Prison) is fragmented, it is a popular pamphlet, both for nonacademic as well as academic readers. In this pamphlet, the author puts forward some very important concepts, such as "non-religious Christianity’, "this-worldliness of Christianity" and the "crucifixion of God". These concepts have a far-reaching impact on the entirety of Christian theology. The Chinese translations, both the Hong Kong version and the Mainland version, are translated from the English translation, instead of the original German version. Mis-translation stemming from this kind of translation will inevitably affect the acceptance of the original text. The purpose of this article is not to compare the differences between the original German text and the Chinese versions from the translation perspective, but is instead, stalling from the contrast between the original German text and the Chinese versions, to re-interpret BonhoefTer's thoughts, and to explore the ethical dimension of Bonhoeffer’s "non-religious Christianity”. [ABSTRACT FROM AUTHOR]

As the slip zone is the weak zone in the landslide, it is the key part to control the stability of the landslide. The study on the change of unsaturated mechanical properties of the sliding zone soil during the drying-wetting cycle is of great significance to understand the change of shear strength of the sliding zone soil with periodic fluctuation of reservoir water and the resulting landslide deformation and even instability process. The sliding zone soil of a talus landslide in Three Gorges reservoir area was used as the research target. Through the simulation of 0-5 drying-wetting cycles, the direct shear and nuclear magnetic resonance (NMR) tests were carried out on the remolded samples of the sliding zone soil, and the matric suction of the samples after shear was measured by filter paper method. Further, the variation characteristics of pore structure, matric suction, soil water characteristic curve (SWCC) and shear strength of unsaturated sliding zone soil during drying-wetting cycle were analyzed, and the prediction model of unsaturated shear strength under drying-wetting cycle was established based on the test results. The results show that the connection between particles in the soil is constantly damaged and destroyed by the drying-wetting cycle, causing the continuous development and expansion of small pores in the sample to evolve into large pores, and the overall porosity increases because the number of pores in the soil increases; meanwhile, the air intake value and the residual water content of soil gradually decreases with the increase of drying-wetting cycles, which means that the water is easier to penetrate and overflow into the soil pores, and the water holding capacity of soil gradually decreases; besides, the degradation of shear strength of slip zone soil is very obvious under drying-wetting cycle; the cohesion and internal friction angle of slip zone soil decrease gradually with the number of drying-wetting cycles, and the degree of weakening of the cohesion by drying-wetting cycle is greater than that of internal friction angle. Finally, the prediction model of unsaturated shear strength of slip zone soil based on direct shear test and matric suction measurement by filter paper method provides a useful reference for the prediction of shear strength of slip zone soil under drying-wetting cycle. [ABSTRACT FROM AUTHOR]

The experiment was to study the allelopathic effect of alfalfa extract on seed germination of perennial ryegrass. The effect of five extracts (0, 2.5, 5.0, 10.0 and 20.0 g/L) from roots, stems and leaves of alfalfa wl-963-HQ on seed germination and seedling growth of perennial ryegrass were determined by Petri dish filter paper method. The results showed that the germination rate, germination potential, germination index and vigor index of the seeds decreased obviously with the increase of the concentration of the extracts from the roots, stems and leaves of alfalfa. The root and leaf extracts of alfalfa had a stronger inhibitory effect on the germination of perennial ryegrass seeds. When the concentration was 20.0 g/L, perennial ryegrass seeds could not germinate normally. Alfalfa extract had no inhibitory effect on root length and seedling height of perennial ryegrass seedlings, but had significant effect on seedling weight. The extracts from the roots, stems and leaves of alfalfa significantly decreased the chlorophyll content of perennial ryegrass seedlings (P<0.05), and the POD activity was significantly increased (P<0.05). Compared with the control group, CAT activity of perennial ryegrass seedlings was significantly increased when the stem extract of alfalfa was 10.0 and 20.0 g/L (P<0.05). The study indicates that alfalfa extract has obvious allelopathy on perennial ryegrass, and reasonable row spacing was needed to reduce allelopathy when the two herbage are mixed. [ABSTRACT FROM AUTHOR]

Considering the unique users of scholars' social networks, this paper proposed a collaborative association model of paper and project data based on scholars' social networks. Firstly, the proposed model used the two-step feature selection method to preprocess the data, removed the irrelevant and redundant features and obtained the effective features that affected the association between the paper and the project. Then it would adopt TVSM to calculate the text similarity between the paper and the project, then formed recommendation sets for different papers/projects. Through the social network (SCHOLAT) data for researchers, the model was implemented and applied to SCHOLAT. The online application situation and user feedback show that the model has good accuracy and practicability. Furthermore, it can more fully explore the potential relationship between the paper and the project, provide users with better academic research management services, and propose a novel research method for analyzing the academic big data. [ABSTRACT FROM AUTHOR]

Surface-enhanced Raman scattering is a highly sensitive and non-invasive analytical technique. This technique can be widely used for the identification and quantitative analysis of materials. In this paper, a simple method for preparing SERS substrates was proposed. First, graphene oxide (GO) was absorbed on the filter paper by leaching-lifting, followed by homogeneous deposition of noble metal nanoparticles by plasma sputtering on the filters. The surface-enhanced Raman scattering properties of the substrate were analyzed with a concentration of 10-5 mol/L rhodamine 6G (R6G). The results show that GO had a good fluorescence quenching effett in Raman detection. The gold and silver nanoparticles with an absorption peak of 532 nm greatly enhanced the Raman scattering signal of R6G via localized surface plasmon resonance (TSPR). In addition, the fiber structure of the filters was able to capture more R6G molecules. Hence, the substrate exhibited excellent SERS characteristics. [ABSTRACT FROM AUTHOR]

In view of the problem of fuzziness of rating and tag in traditional collaborative filtering algorithms,this paper used trapezoidal fuzzy number to describe the mapping relationship between rating and satisfaction.The algorithm considered the impact of sparseness of the rating,constructed a new trapezoidal fuzzy rating model to determine the similarity based on fuzzy rating,analyzed the degree of membership between the tag and the item,and constructed a fuzzy item-tag matrix to measure the similarity based on the degree of tag membership.Finally,it used the improved scoring prediction strategy to estimate the score.The experimental results on the MovieLens dataset show that the proposed algorithm improves the prediction accuracy while suppressing the cold start of the project,alleviating the problems of fuzziness and sparseness,which indicates the effectiveness of the proposed algorithm. [ABSTRACT FROM AUTHOR]

A ship will bear large vertical and lateral overloads when dropped into water，which imposes adverse effects on the structural strength and stability of the ship. The overloads can be reduced by controlling the pitching angle of the ship. In order to study the influence of the pitching angle on overload reducing, LSDYNA is used to simulate the landing process at different angles. The acceleration curves of landing process under different working conditions are obtained，and the simulation results are verified by the fall-down test. The results show that the reasonable entry angle can effectively reduce the ship’s water overloads. The work in this paper can provide the basis for the landing load reduction of the sea airdrop system. [ABSTRACT FROM AUTHOR]

As the core equipment in power grid, the reliability of transformers directly effects the safe and stable operation of the system. And the moisture content is a significant indicator need to be monitored in running of transformers, which have great influence on operating state of them. In order to study its influence on the breakdown characteristics of oil-paper insulation, the pressboard samples with different moisture content were prepared in laboratory. The changing rules of dielectric characteristics with moisture content were tested, its functional rules of electric field distribution were analyzed by simulation as well. Moreover, the influence of above factors on the breakdown characteristics was verified by experimental method. The measuring results show that the conductivity and relative permittivity rise with the increase of moisture content, which causes the transference of electric field distribution into oil in oil-paper insulation system, and finally leading the decrease of breakdown strength of oil-paper insulation system with high moisture content. [ABSTRACT FROM AUTHOR]

In order to improve the quality and the influence of Journal of Natural Resources (JNR), the authors searched papers published in JNR during 1986-2015 in CNKI as the source data and analyzed the characteristics of zero-cited papers. Changes in the number of published papers and the rate of zero-cited papers, the average download frequency and other related information, such as authors, subjects, funds and paper characteristics, were all taken into consideration. The results are as follows: 1) From quarterly journal to bimonthly and monthly journal, the number of published papers in JNR increased, but the rate of zero-cited papers did not increase. 2) These zero-cited papers were still downloaded, which means they have the possibility of being cited in the future. 3) As far as the information the first authors of the zero-cited papers were concerned, doctoral students take the most proportion, followed by master students, assistant professors and associate professors, and professors take the least proportion, and the authors from colleges/universities and scientific institutes are more than the authors from local departments. Most zero-cited papers were written by single author or authors from single institute. 4) Whether a paper was cited or not had little relation with the number and the type of funds. 5) The subjects of most zero-cited papers are pedology, geoscience, meteorology and environmental biology. Finally, several suggestions are given to reduce the rate of zero-cited papers through the cooperative control of authors, peer reviewers and journal editors. [ABSTRACT FROM AUTHOR]

Conductive silver paste is a key functional material for the preparation of electronic components. Conductive silver paste with silver and starch used as conductive fillers was prepared by redox method with molar ratio of starch to silver nitrate of 2: 1, 1 : 1, 1 : 2 and 1 : 3. The effect of physical factors, such as heating and sintering, ultraviolet light irradiation, soaking water, and ultrasonic wave, on the conductivity of the conductive silver paste was studied by measuring resistance, and the morphology of the conductive silver paste was observed with a microscope. The results showed that when the starch/silver nitrate was 1 : 3, the uniform conductive particles with starch as core and silver particles as shell were formed. When the ratio was 1 : 2 and 1 : 3, the resistivity decreased to 60% to 70% of the initial value during the low-temperature heating and sintering. The resulting silver paste was resistant to UV light, blisters and ultrasound. Among them, the conductivity for the sample prepared with the molar ratio of 1 : 3 was the best. Finally, a silver paste with a starch/silver nitrate ratio of 1 : 3 was mixed with 30%, 45%, or 60% of the ink, coated with paper, and subjected to low-temperature thermal sintering, and the resulting electronic paper had a resistivity of 10 mΩ/cm. [ABSTRACT FROM AUTHOR]

As a kind of renewable fiber, tencel fiber has the characteristics of multiple fibril structure. Tencel fiber prepared by fibrillation treatment can be widely used in materials such as supercapacitors and battery separators. In this paper, the highly fibrillated tencel fiber was selected, and the influence of the structure of tencel fiber paper on its dielectric constant and breakdown voltage was discussed. The results show that the measured values of the relative dielectric constant of the tencel fiber paper were in good agreement with the empirical calculations based on the volumetric empirical formula. Using 40 g/m2 electrolytic capacitor paper prepared with tencel fiber, the dielectric strength after calendering could reach 18.27 kV/mm. Considering the composite dielectric series capacitance model, the breakdown voltage of the double-layer tencel fiber paper could be calculated according to the parameters of single-layer paper, thereby guiding the structural formula design of the doublelayer capacitor separator. [ABSTRACT FROM AUTHOR]

Mil-101(Cr), a metal framework compound with high specific surface area and excellent thermal stability, was synthesized by solvent thermal method. MIL-101(Cr)/PI fiber paper-based composites were made of polyimide fibers and para-aramid fibers as raw material and introducing presynthesized MIL-101(Cr)via modern wet-forming papermaking technique. The influence of content of MIL-101(Cr)on filtration performance of paper for hot gas was analyzed. The results showed that the filtration performance of paper-based composites with MIL-101(Cr)increased remarkably, the quality factor enhanced by 152. 69% and 558. 22% at room temperature and 260°C respectively. [ABSTRACT FROM AUTHOR]

The biodegradable composite material was prepared by injection molding with PHBV as matrix and microcrystalline cellulose and waste paper fiber as reinforcements. The iffects of MCC with different mass fraction and waste paper fiber with different mass fraction on the mechanica properties, water absorption and interfacial properties of the composites were investigated. The results show that the mechanical properties of the composites after adding MCC have been improved and the mechanical properties of the composites are the best when the mass fraction of MCC is 3%. And the composite material after blending and filling has the best combination mechanical properties when the mass fraction of waste paper is 10%. The water absorbency of composites increases with the increase of fiber content in waste paper. Scanning electron microscopy analysis shows that the compatibility of MCC with P-HBV interface is better and the interfacial properties of blended waste paper fibers decrease. [ABSTRACT FROM AUTHOR]

The electro-acoustic (frequency response) characteristics of the loudspeaker usually be affected by the mechanical properties of the paper diaphragm. The mechanical properties of the diaphragm were improved by modifying the natural fiber. In this work, the structure of Manila hemp fiber and the mechanical properties, electro-acoustic performance of paper diaphragm were discussed on the effects of alkali concentration and treatment time. The surface morphology, crystal structure and chemical composition of Manila hemp fiber treated before and after were characterized by SEM, XRD, FT-IR, TGA. The results showed that the fiber surface roughness increased, and the crystallinity of the fiber increased and then decreased as the alkali concentration or the treatment time increased. The lignin and hemicellulose on the fiber surface were decreased. The thermo-stability of cellulose improved the same time lignin’s decreased. When the alkali concentration was too large or the treatment time was too long, the cellulose will be degraded, the mechanical strength of the diaphragm was affected. The fiber diaphragm has the best mechanical properties and electro-acoustic performance with 5 wt% of the alkali concentration, 3 h of the treatment time. [ABSTRACT FROM AUTHOR]

Glass fiber paper is a kind of excellent non-flammable, heat and sound insulation, filterable materials, which is widely used in high-speed rail, aerospace and marine areas. This paper mainly explored pore diameter distribution, air permeability, heat and sound insulation property of glass fiber paper prepared of beating by wet process with different diameter fiber . The results show that with the increase of content of fine glass fiber of paper, the average pore diameter and air permeability decrease firstly and then increase ,the thermal conductivity of paper decrease firstly and increase subsequently, the sound transmission loss of paper increase firstly and decrease subsequently. With the ratio of 50% crude fiber and 50% fine fiber, the glass fiber paper had the best heat and sound insulation properties. [ABSTRACT FROM AUTHOR]

In order to improve the utilization of apple pomace resources, verify the antibacterial activity and antiseptic properties of the ethanol extract of apple pomace, the antibacterial activity of extract from apple pomace were determined by the inhibition zone test. In addition, the antibacterial effect of the extract under different pH and salt concentration had been studied. At the same time, the ethanol extract of apple pomace was applied to the preservation of Passiflora edulia, using sensory scores and various physical and chemical indicators(Vc, soluble solids, total acid, solid acid ratio)as the basis to investigate the antiseptic effect of the extract. The results were as follows:(1)The ethanol extract of apple pomace had no obvious inhibitory effect on yeasts(diameter of inhibition zone <1 mm), but it had obvious inhibitory effect on Staphylococcus aureus and Escherichia coli(diameter of inhibition zone was 6-9 mm).(2)The best inhibitory concentration for these strains was 4.0 g·L-1. In addition, when the antibacterial effect of the extract was optimal, the pH was 6-7 and the salt concentration was 5.0 g·L-1.(3)The optimal concentration for Passiflora edulia was 0.2%, and the rot rate after storage at this concentration was only 6.7%(control group was 67%), and the weight loss rate was 5.5%(control group was 36.3%). The soluble solids and total acid content were not significantly different from those before storage(P>0.05)(control group P<0.05). And most of the fruits were plump, firm, bright and shiny, moderately sweet and sour. The antibacterial extract of apple pomace has antibacterial activity and significant antiseptic effect, and provides a theoretical basis for the development and utilization of apple pomace resources. [ABSTRACT FROM AUTHOR]

This study aims to improve the utilization rate of abandoned corn bracts, while decreasing the production cost of the bag of fruit cultivating in sustainable agriculture. Five representative bags of fruit cultivating were collected in the market as the controlled samples, including the plastic film bag A, special bag B for grape, one-, two- and three-layered bag C, D, and E. The basic structural characteristics of controlled samples were firstly analyzed. Then, alkali cooking was used to degum the corn bracts for the extraction of fibers. Subsequently, the corn bract fibers were cut into (5±0.5) mm long, thereby mixing evenly with the waste paper scraps in a ratio of 1.5:1. The wet mesh forming was adopted to prepare the fruit-cultivating bag material F. The mechanical properties of material F were tested after fabrication. The experimental results showed that the prepared material F behaved a strong tensile resistance, where the tensile loads for the dry and wet material F were up to 20.02 N and 13.79 N, respectively. Moreover, the retention rate reached 68.9% for the tensile load of wet material F. Furthermore, an excellent extension performance was achieved for the high requirements of mechanical properties in the fruit bagging. A scanning electronic microscopy (SEM) was adopted to observe the microstructure of the prepared materials F and the controlled samples in the market, further to analyze the distribution of holes in the matrix. The bagging properties were also measured, including air permeability, heat-insulating property, shading property, and water management ability. The experimental data demonstrated that the fruit-cultivating bag material F presented an excellent air permeability. Specifically, the air-flow rate and permeability of material were 73.5 mm/s and 173.7 L/m2 •s, respectively. In contrast to the controlled samples, the maximum air-flow rate and permeability were only 2.5 mm/s and 0.3 L/m2 •s, respectively. In addition, the heat loss of boiling water was about 265 kJ, when the prepared material was used to keep the boiling water for 60 min. The transmittance of the material F was about 0.4 % in the visible light range, and 0.09 % in the ultraviolet light range. The shielding properties showed that the prepared material ensured the photosynthesis of fruits during the growth process. Meanwhile, material F was expected to protect the fruit from ultraviolet light burning. Excellent ability of water conductivity was also achieved, where the core suction height reached 31 mm within 30 min. As such, the water in the fruit-cultivating bag during rainy days discharged quickly to enhance the quality of fruit products. Low wet evaporation indicated that the water retention performance was obviously better than that of the special bag B for the grape in the market. Most significantly, the thermal insulation performance of the new fabricated material was better than that of the controlled samples in the market. [ABSTRACT FROM AUTHOR]

[Purpose/Significance] The National Preprint Publishing Platform of China had been put into operation by the end of 2022. In order to ensure the quality of papers posted on the Platform and encourage a large number of researchers to submit articles to the Platform, it is necessary to introduce a paper quality assurance mechanism into the Platform. There are deficiencies in existing quality assurance mechanism for a preprint publishing platform. Self-organizing peer review has gradually attracted attention in recent years. In order to achieve the performance expected by the management agency of the National Preprint Publishing Platform, it is necessary to study the optimization design of key parameters of self-organizing peer review. [Method/Process] Design-expert software has been used for Box Behnken experimental design. The number of papers submitted by authors within a year, the distribution of review time, and the parameters of article review time are randomly set. The total number of papers is calculated according to the parameters of Lotka's law, and is not included in the Box-Behnken experimental sampling. We selected four key parameters of rest time, rejection rate, number of researchers, and review qualification ratio as independent variables, took three levels for each variable, and used -1, 0, +1 for coding, representing three levels of low, medium, and high, respectively. The three dependent variables for self-organizing peer review performance evaluation are the completion rate of paper review (CR), the balance of reviewer task allocation (TBD), and the average review time of the paper (A_r_time). A Box-Behnken experiment table was designed separately for each Lotka's law parameter, three repeated experiments were conducted on each key parameter combination in the table, and the summary() function and mean() function in R language were used to calculate the average performance indicators of each key parameter combination. Then, the response surface analysis was carried out on the Box-Behnken sampling data, and the quantitative relationship expression between the dependent variable of performance evaluation and the independent variable of key parameters was obtained. [Results/Conclusions] The ratio of review qualifications and reviewer rest time have greater impact on the performance of self-organized peer review, especially the ratio of review qualifications is much more important than other three key parameters. By combining different values of key parameter independent variables, the National Preprint Publishing Platform can achieve the expected self-organized peer review performance, ensuring the average quality of papers published by the Platform. In addition, because of our limited knowledge of computational resources, there is still room for improvement in simulation accuracy. If equipped with more powerful computational resources, more precise simulation calculation can be carried out based on the methods and parameters proposed in this paper. [ABSTRACT FROM AUTHOR]

This paper proposed an electronic voting scheme based on one-time ring signature and blockchain to solve the problems of the current e-voting system in terms of anonymity, transparency and open vote-counting. This paper introduced one-time ring signature, blockchain and stealth address technology. The one-time ring signature technology solved the problem of voter anonymity, repeated voting and public verification. The blockchain technology could ensure the openness and transparency of the e-voting system. The one-time ring signature technology could ensure no one or institution could obtain the voting intermediate result before the voting ends. In order to improve the efficiency of vote-counting,it used the method of key sharing to improve the vote-counting algorithm. Through security and performance analysis, the scheme conforms to the basic security standards of an electronic voting system. [ABSTRACT FROM AUTHOR]

In order to study the effects of different atmospheres ( nitrogen and air) and temperature ranges (300 ~ 500 °C, 300 ~ 700 °C and 300 ~ 900 °C ) on the composition and amount of pyrolysis products in paper-making reconstituted tobacco substrates, solid phase microextraction, adsorption-desorption and gas chromatography-mass spectrometry methods were used for analysis. The results showed that under the nitrogen and air atmospheres, the pyrolysis products of substrates at the range of 300 ~ 700 °C and 300 ~ 900 °C obviously increased when compared with those at the range of 300 ~500 °C . A large number of polycyclic aromatic hydrocarbons and olefins were produced in these two temperature ranges. Nicotine was only found in the pyrolysis products of substrates at the range of 300 ~ 500 °C. The contents of furfural and phytadiene were higher at these three temperature ranges. In the same temperature range,under the air atmosphere,the release amount of important cleavage products such as crotonaldehyde, 2-methyl-furan and furfural with relatively low molecular weight was higher than that under nitrogen atmosphere. The relative release of alcohols increased, and the presence of oxygen in air promoted the full combustion of substrates, thereby resulting in the reduction of total pyrolysis products. [ABSTRACT FROM AUTHOR]

The DJI MG1-P electric four-rotor plant protection unmanned aerial vehicle was used for spraying in the mid-growth-cotton. And the effects of spray parameters and adjuvant type on the deposition and distribution of pesticide mist droplets on cotton plant leaves were discussed. 22% flonicamidonitrile SC and three kinds of spray adjuvants (Beidatong, ND-800, G-2801) were used as test agents, which were sprayed under different spray parameters and different aerial spray adjuvants. As a tracer of pesticide deposition, allura red was employed to detect the distribution of droplet deposition using water sensitive paper and filter paper. The absorbance value of the filter paper elution solution was measured by a spectrophotometer. The absorbance value of the filter paper elution solution is measured by a spectrophotometer in order to calculate the amount of drug solution deposited per unit area, and the droplet density was analyzed by DepositScan software. The test results showed that the flight speed of unmanned aerial vehicle had the greatest influence on the droplet deposition distribution, and the flight height had no significant effect on the experiments using the middle of cotton growth. The adjuvant had a significant effect on the spray deposition distribution. After adding the spray adjuvants, the droplet densities on the upper, middle and lower parts of the cotton canopy were all significantly improved. After adding ND-800 adjuvant, the droplet density on the back of the upper, middle and lower leaves of the cotton canopy increased by 688.9%, 590.9% and 327.5%, respectively. However, the addition of G-2801 and Bidatong adjuvant had no significant effect on the droplet density on the back of cotton leaves. [ABSTRACT FROM AUTHOR]

[Objective] The present paper aimed to get high efficient cellase-producing bacteria and determine the taxonomy. [Method] Sodium carboxymethylcellulose was selected as the sole carbon source to isolate cellulose-producing microorganism. A total of 51 bacteria and actinomyces were isolated from natural fermentation material of tobacco straw.Nine isolates possessed high cellulase activities in congo dye experiment. The phylogenetic relationships of cellulase producing bacteria and actinomyces were determined through the analyses of phylogenetic trees constructed using 16 S rRNA gene sequences. [Result] Luteibacter sp.L43 possessed the highest cellulase activities in enzyme activity tests. The effects of the single factor including pH, carbon and nitrogen concentration on filter paper enzyme, endo-β-1, 4-glucanases and exo-β-1, 4-glucanases for L43 were determined.Under the condition of pH6, sodium carboxymethylcellulose concentration 12.5 g/L and NaNO3 concentration 5 g/L, the highest cellulase activities of endo-β-1, 4-glucanases and exo-β-1, 4-glucanases of L43 were 16.9 and39.62 U/mL, respectively. [Conclusion] This study provided a good cellulose producing bacteria for tobacco straw fermentation and laid a foundation for the development and utilization L43. [ABSTRACT FROM AUTHOR]

A green starch-based bio-latex was prepared and used as a coating adhesive for par tially replacing styrene butadiene latex, which have been successfully applied in the coated Art Paper. In the study,different proportion of starch-based bio-latex(0% ,10% .20% .30% 40%) was used to replace the styrene-butadiene latex in the coating formulation, and then the coating experiment was carried out on the base paper. Through testing and analyzing the performance of the coating color and coated paper, the best coating color formulation has been determined. And the results indicated that the biological latex could partially replace the SBR latex as an adhesive in the coating. [ABSTRACT FROM AUTHOR]

The effects of different types of combustion supporting agent in cigarette paper on the overall sensory quality of cigarettes were analyzed by sensory evaluation. Variation analysis on the difference of weight difference between the sensory indexes which affect the weight of cigarette smoke was carried out by principal component analysis technique. The results showed that: the overall sensory quality of cigarette with potassium citrate as combustion supporting agent was better, while the overall sensory quality of cigarette with potassium lactate as combustion supporting agent was poor, the order of the effect of the types of combustion supporting agent on seven main indexes of sensory quality was aftertaste > ordor > coordination > aroma > state > drying > stimulation. [ABSTRACT FROM AUTHOR]

In the process of detecting human respiration and heart rate using millimeter wave radar, the static clutter in the environment makes it extremely difficult for the radar to discriminate the information about the movement of the human chest cavity, which affects the separation of respiration and heart rate signals. At the same time, it is difficult to separate the harmonic components of the respiration signal in the high-frequency band and the heartbeat signal in the low-frequency band because the frequencies of the harmonic components in the high-frequency band are similar.To solve the above problems, this paper proposes a joint modal spatial domain estimation detection method, which mainly adopts an single ensemble empirical modal decomposition (SEEMD） algorithm to decompose the thoracic phase signal into each modal component to eliminate the influence of static noise on the respiratory heartbeat signal, and then uses a multiple signal classification (MUSIC) algorithm to convert the heartbeat modal component signals from the time domain to the spatial domain to estimate their frequencies to eliminate the influence of respiratory harmonics.The experimental results show that the accuracy of respiratory rate under the detection of this paper’s method is 95.76%,and the accuracy of heart rate is 98.76%.Compared with the traditional algorithms, the proposed method is more accurate in estimating respiratory rate and heart rate. [ABSTRACT FROM AUTHOR]

Underwater fish target recognition technology is an important technology in ocean exploration. However, the acquisition of underwater resources is very expensive and cannot meet the requirements of training large-scale deep neural networks. Aiming at the problem of small or even zero samples of underwater fish data, this paper proposed a Joint Deep Statistical Feature Alignment（JDSFA) method based on transfer learning to solve the problem of fish target identification in small samples. Using ResNet-50 as the backbone network, the mean square and covariance were incorporated into the weight selection algorithm to construct a joint domain adaptive loss function to align the feature distribution between the source domain and the target domain. In addition, we also designed a global loss function to combine the source domain loss with the inter-domain adaptive loss by using adaptive weights to realize the fish target recognition task. The published underwater fish data set QUT was used for experimental verification, and the results all showed that the effectiveness of JDSFA method in fish identification was 3.59%,4.96% and 5.91% higher than that of the current representative DADAN, PMTrans and DSAN methods, respectively. It is further demonstrated that the JDSFA method proposed in this paper has good application value in fish identification task. [ABSTRACT FROM AUTHOR]

BACKGROUND: With the continuous improvement and progress of the magnetically controlled growing rod technology in the field of the treatment of spinal deformities, numerous studies have been put into this field, but the main research status, hot spots, and development trends are not clear enough. OBJECTIVE: Based on bibliometrics, this paper discusses the quality and quantity of articles in the field of using magnetically controlled growing rods to treat spinal deformities from different countries, aiming to clarify the global development trend of magnetically controlled growing rods and evaluate the research productivity, research trends, and research hotspots in the world. METHODS: The articles published from 1998 to 2023 were retrieved mainly based on the Web of Science database. CiteSpace 5.8 and VOSviewer 1.6.19 software were used to analyze the data and generate a visual knowledge map. The following parameters were evaluated for all studies: the total number of published papers, centrality, h index, the contribution of countries, authors, and journals, and the trend and hot spots were explored through the analysis of co-citation, highly cited literature, and literature keyword explosion. RESULTS AND CONCLUSION: (1) Finally, 138 articles were included. From 2009 to 2020, the number of published articles in this field gradually increased. The United States has the largest number of articles (53, 37.32%), and the United States has the highest h index and centrality of articles. (2) The results of keyword analysis showed that: the top ten keywords, such as early-onset scoliosis, surgery, complications, and so on, objectively and truly reflected the current situation and hot spots of magnetically controlled growing rod in the field of spinal deformity treatment. In recent years, the research focus in this field is the treatment failure caused by risk factors such as the pull-out of the magnetically controlled growing rod, implantation failure, and rod fracture, the accurate use of the corresponding medical classification, the monitoring and treatment of complications such as quality of life and cerebral palsy. (3) The co-citation results showed that: combined with the innovative and effective research of the magnetically controlled growing rod technology, the classification application of spinal deformity and the monitoring and treatment of related complications may be the research trend in this field. (4) Many highly cited articles further emphasized the therapeutic effect of magnetically controlled growing rod technology, providing an effective new idea and technical support for the field of spinal deformity correction. (5) The results of literature keyword explosion analysis demonstrate that the risk factors, medical classification, quality of life, and cerebral palsy of the application of magnetically controlled growing rods may become the research frontier in this field. (6) It can be seen that the application of magnetically controlled growing rod technology in the classification of spinal deformities and the in-depth study of related complications are the development trend in this field, but to further understand the effectiveness and safety of magnetically controlled growing rod technology in the treatment of spinal deformities, we still need long-term follow-up evidence. The overall research level of this field has steadily improved in recent years, but there are also problems such as the small number of high-quality articles and the unbalanced development of research in various regions. [ABSTRACT FROM AUTHOR]

Taking CNKI Full-text Database as the data source, the literatures on the study of Amorpha fruticosa L.published from 2012 to 2021 were retrieved, and the annual change trend of number of articles, literature types, research teams, research institutions, research high-fre- quency words, single citation frequency and literature research direction were analyzed systematically by Excel and VOSviewer softwares. The results showed that from 2012 to 2021, a total of 618 Chinese literatures related to A. fruticosa were included in the CNKI database, of which 261 papers (43.72%) were forestry literatures. Among all these literatures, 193 were supported by fund projects, and 167 (86.53%) were supported by national fund projects. The research institution with the largest number of papers was Northwest A & F University, with a total of 57 papers (25.68%). Journal of Northwest A & F University collected the most related literatures on Amorpha amorpha, number of which was 25 in total. Moreover, the ecology and environment, afforestation and cultivation, plant physiology of A. fruticosa were the research hotspots in recent years. China had achieved high level of scientific research results in these three research directions. Although the number of literatures on A. fruticosa showed a downward trend since 2014, it had increased in 2020, which indicated that the scientific research value of A. fruticosa had regained the attention of scholars. [ABSTRACT FROM AUTHOR]

Urban-rural integration is the only way for rural revitalization and the due meaning of new urbanization. Digital inclusive finance enables new fusion of industrial elements to promote urban-rural integration. Based on the inter provincial panel data from 2011 to 2020, this paper tests the impact of digital inclusive finance on urban-rural integration and its transmission mechanism. The study found that digital inclusive finance can effectively promote urban-rural integration. Further research found that digital inclusive finance promotes the optimization and upgrading of industrial structure and indirectly promotes urban-rural integration; digital inclusive finance and urban-rural integration show strong spatial relevance in space, but have not produced spatial spillover effect. The research of this paper provides evidence, experience and policy enlightenment for guiding the deep integration of digital technology and inclusive finance, optimizing industrial structure, strengthening interval links, breaking administrative barriers and realizing the deep integration of urban and rural areas. [ABSTRACT FROM AUTHOR]

Essential oils are expensive and have the name of "liquid gold". It has a strong aroma and is widely used in food, cosmetics and tobacco. Studying the extraction and application of rose essential oil will improve the economic efficiency of the essential oil industry. This paper reviews the extraction methods and advantages and disadvantages of rose essential oil in recent years, and introduces the antioxidant, antibacterial and anti-anxiety properties of rose essential oil, and summarizes the application of rose essential oil in daily life. This paper also presents an outlook on the subsequent development of essential oil applications in order to provide some theoretical support for the development and research of the extraction and application of rose essential oil. [ABSTRACT FROM AUTHOR]

BACKGROUND: In recent years, numerous studies have shown that long non-coding RNAs (lncRNAs) have an important role in the pathogenesis of periodontitis, including the immune response process and the biological activity and function of cells (periodontal stem cells and osteoblasts). Researchers attempt to regulate periodontal inflammation and periodontal regeneration by regulating lncRNA expression levels. OBJECTIVE: To review the progress of research on lncRNAs in periodontitis, thereby advancing the research of lncRNAs in periodontitis. METHODS: The first author searched PubMed, China National Knowledge Infrastructure (CNKI), Web of Science database, and WanFang Database for relevant literature published up to March 2023. “Long non-coding RNA, lncRNA, periodontitis, periodontium, immunity, inflammation, periodontal ligament stem cells, osteoclasts, osteogenic differentiation, bone resorption, bone formation, recurrence, hypoxia, oxidative stress, static mechanical strain”were used as the Chinese search terms. “lncRNA, periodontitis, periodontal, immunity, inflammation, periodontal membrane stem cells, osteoclasts, osteogenic differentiation, bone resorption, bone formation, recurrence, hypoxia, oxidative stress, static mechanical strain” were used as the English search terms. The title and abstract of each paper were read for initial screening, and 87 papers were finally selected for inductive analysis. RESULTS AND CONCLUSION: Periodontal pathogens stimulate the body, leading to immune imbalance that triggers inflammatory response and destroy periodontal tissue, and lncRNAs are involved in its regulatory mechanism. LncRNAs are involved in the pro-inflammatory regulation of periodontal ligament cells in an inflammatory environment, and their effects on osteoclast differentiation are regulated through ceRNA mechanism, which provides new clues for exploring the pathogenesis of periodontitis. For B cells and macrophages, lncRNAs can regulate the infiltration, cell activity and function of their subsets in periodontitis. LncRNAs participate in the immune response related to periodontitis mainly through two pattern recognition receptors, Toll-like receptors and NOD-like receptors, and nuclear factor-κB signaling pathway. To investigate whether lncRNAs can be used as a biomarker of periodontitis has great value in the diagnosis and prognosis of periodontitis. Animal experiments have demonstrated that the role of lncRNAs in periodontitis can be reversed by modulating the expression level of lncRNAs and thus lncRNAs act as an anti-inflammatory agent, which is of great value for the study of immunotherapy in periodontitis. The regulation of lncRNAs on periodontal ligament stem cells is mainly realized through endogenous competition mechanism and various signaling pathways, and its effects are influenced by various factors, such as inflammatory environment, mechanical strain, hypoxia and oxidative stress. Research on related mechanisms through these related factors provides new ideas for the treatment of periodontitis. [ABSTRACT FROM AUTHOR]

Plant extracts are natural active substances derived from plants, which have the functions of anti-oxidation, anti-inflammation, regulating flora. They are widely used in medicine, food and other fields. Many studies have showed that plant extracts have great beneficial effects in animal husbandry and are important green feed additives. In this paper, the research progress on application of plant extracts in laying hens was reviewed. The regulatory effects of plant polyphenols, plant polysaccharides, plant flavonoids and alkaloids on the productive performance, anti-oxidative, immune function, lipid metabolism and intestinal flora of layers were emphatically described. The purpose of this paper was to provide reference for the application in layer production. [ABSTRACT FROM AUTHOR]

In order to explore the hotspots and research trends of domestic research on biochar in tobacco agriculture in recent years, bibliometric methods were used to analyze papers about biochar application in tobacco planting research included in the China National Knowledge Infrastructure (CNKI). The numbers, annual distribution, author information, publications and research content were statistically analyzed, and the CiteSpace V visualization software was used to predict and analyze research hotspots. The results showed that a total of 114 journal papers and 81 dissertations on the application of biochar to tobacco planting were retrieved, including 8 doctoral dissertations and 73 master’ s dissertations. The institution with the most research in China was Henan Agricultural University, and Liu Guoshun was the scholar with the most published papers. Domestic research on tobacco biochar still lacked a stable core author group, and the number of core authors was small. Tobacco biochar application hotspots focused on tobacco quality, chemical composition and tobacco-growing soil. In recent years, research hotspots tended to be on the effects of biochar on soil microbial communities and heavy metals in tobacco leaves. [ABSTRACT FROM AUTHOR]

Accurately identifying the spatial characteristics of “non-grain” cultivated land and proposing control measures have positive significance for accurate control of “non-grain” cultivated land. Taking Youjiang District as the research area, this paper identified the spatial characteristics of “non-grain” cultivated land in Youjiang District from the aspects of land type composition, slope distribution, landscape pattern, spatial adjacency, farming distance and transportation convenience. This paper proposed optimization and control measures for different types of “ non-grain” cultivated land to in order to guide cultivated land to grow food. The results show that: The total amount of “non-grain” cultivated land in Youjiang District has reached 308. 38 km², mainly dry land, followed by garden land and forest land. The slope of “non-grain” cultivated land is mainly greater than 6°, and when the terrain slope is less than 25°, the area of “non-grain” cultivated land increases with the increase of slope grade. “Non-grain” cultivated land is fragmented, with high spatial proximity to gardens and woodlands, and strong interaction. The closer to rural settlements (less than 800 m) and roads ( less than 1 200 m), the larger the proportion of “ non-grain” cultivated land, and the spatial distribution of “non-grain”cultivated land is affected by cultivation distance and transportation convenience. [ABSTRACT FROM AUTHOR]

Accelerating the citizenization of agricultural migrant population is an important task to realize urbanization, and the fundamental reason for the slow progress of citizens is the excessively high cost of urbanization of agricultural migrant population. At present, there are a considerable number of research findings concerning the cost of agricultural transfer of population urbanization. This paper adopts literature analysis method to review and sort the relevant research results of domestic scholars on the cost-sharing of urbanization for agricultural transfer populations. It elaborates on aspects such as the composition of cost-sharing for urbanization of migrant agricultural populations, precise calculation and quantitative methods of cost-sharing, and the construction of cost-sharing mechanisms. By combing and summarizing the existing research literature, the paper continuously promotes the in-depth study on the cost sharing of citizenization of the migrant agricultural population, so as to promote the development of new urbanization and rural revitalization. [ABSTRACT FROM AUTHOR]

Data classification and grading is the foundation for ensuring the safe circulation of data and promoting the release of data value. This paper focuses on the key task of government data classification and grading in digital reform. Using a theoretical case study method and based on publicly released plans by various provincial governments and ministries, the implementation of government data classification and grading in China is systematically sorted and quantitatively analyzed. This paper summarizes four key processes and five characteristics of the implementation of government data classification and classification in China. Based on the special complexity of the classification and grading of government data, this paper puts forward four problems corresponding solutions in the implementation of the classification and grading of government data in China, such as unclear overall target positioning, different classification and grading objects, separated classification and grading relations, and different security grading standards. Based on the practice of classification and grading government data of a national ministry, this paper verifies the scientificity and effectiveness of the solutions, and provides a reference for constructing a unified national government data classification and grading system. [ABSTRACT FROM AUTHOR]

Building a high-quality big data resource platform for the government is an important basic project to realize the integration of government information across departments, regions and levels, accelerate the construction of digital government and improve the digital intelligence level of public services and social governance. Firstly, this paper reviews the development of China's E-government and summarizes the three construction mode and main problems of traditional big data platforms, i.e., low data freshness, poor data consistency, difficult business collaborative management, weak basic support and high overall investment. Secondly, this paper conducts a case study on the credit information resource management platform in Jiangsu and explains the reasons for using Jiangsu case as an example. This paper proposes corresponding solutions and overall architecture design for the problems existing in traditional construction models as well as four reference value of Jiangsu case. Finally, based on summarizing the research and practical experience in Jiangsu, five suggestions are summarized to provide a reference for various provinces to study and formulate policy documents, such as provincial government big data platform construction guidelines. [ABSTRACT FROM AUTHOR]

News recommendation system plays an important role in news dissemination of new media. This paper proposed a recommendation system based on deep reinforcement learning, which aimed to combine the representation ability of neural network and the strategy selection ability of reinforcement learning to improve the effect of news recommendation. This paper used dynamic action masks to enhance the ability of judging the short-term interests of users, used the optimization cache mechanism to improve the efficiency of experience cache use, and accelerated model training through the reward design of regional masking nature to improve the performance of the recommendation system in the field of news recommendation. Experimental results show that the accuracy of the proposed model in news data sets is comparable to the current mainstream neural network recommendation methods, and its ranking performance is better than others. [ABSTRACT FROM AUTHOR]

In order to ensure that the overall prefabricated underwater push-out final joint can control the safety risk during construction process under offshore conditions, and to meet the design requirements of centimeter-level installation and docking accuracy, this paper explores the issue of the closure width in the final joint construction of steel shell immersed tunnels. By analyzing the actual construction parameters of the installed pipes and the specific weather window conditions, this paper focuses on the entry method of the pipe into the closure, the longitudinal positioning ability of the pipe, and the cumulative length errors of the tunnel prefabrication and installation. The results show that controlling the closure width of the final joint at2.2 m is beneficial for providing space for post-welding operations, enhancing ventilation effects, satisfying large-scale welding operation conditions, facilitating the deployment of large -scale equipment, and improving work efficiency. Meanwhile, it provides an effective space for sinking and docking operations in the construction of immersed pipes, reducing operational risks. This study is of great significance to provide useful references for the final joint construction of steel shell immersed pipes. [ABSTRACT FROM AUTHOR]