Search

The effects of furfural generation and partitioning on the aging assessment of oil-paper insulation of power equipment were investigated. Oil-paper samples with various furfural contents were prepared using an accelerated thermal aging experiment. The mass of the furfural generated during the aging of insulation paper was calculated and used to establish the quantitative equation between the accumulated furfural and the degree of polymerization (DP) of the insulation paper. Results showed that the reciprocal of the DP value was linearly related to the amount of furfural generated by the insulation paper. Effects of temperature, moisture, and temperature on the furfural partitioning ratio between oil and paper were analyzed using a furfural partitioning experiment, and a furfural partitioning model was established. Results showed that the furfural partitioning ratio in oil was positively correlated with temperature and moisture but negatively correlated with the DP of the insulation paper. A method for assessing the age of an insulation paper by integrating the furfural generation and partitioning models was proposed and applied on a 500-kV reactor that was returned for factory maintenance. The application result indicated that the method could accurately assess the overall aging condition of the oil-paper insulation of the power equipment.

Traction transformers are one of the most important equipment in the traction power supply system. Thermal aging of transformer insulation system determines its reliable life. To achieve an estimation of the insulation life of traction power transformers operated under real load condition, the effects of traction loads on the thermal aging of oil-paper insulation in traction transformers were investigated. First, the design principles for the accelerated thermal aging experiment were studied and proposed by considering magnitude (i.e., load rate) and frequency (i.e. spare time and lasting time) of the traction load. Then, an experimental system was established in the laboratory to conduct extensive accelerated thermal aging experiments, in which the traction loads were mimicked by using positive temperature coefficient (PTC) heating plates and a programmable logic controller (PLC). Finally, the experimental results were analyzed and discussed to reveal the effects of traction load on the thermal aging of oil-paper insulation in traction transformers.

Oil-paper insulation ageing of transformer has characteristics of spatial locality due to uneven temperature distribution. The transformer is sealed, it is difficult to obtain the local ageing state of oil-paper insulation by sampling directly. Currently, there are no effective detection method to detect the insulation state of local regions. The oil-immersed paper resistivity inversion method can nondestructively assess the local state of oil-paper insulation. However, the current inversion methods still have shortcomings and need to be improved. In this paper, combining the back propagation neural network (BPNN) and Newton downhill method (NDM), an improved inversion method is proposed to optimize the current inversion method, so as to reduce the effect of initial value on it and make calculated results converge better. Finally, a 3D 10 kV transformer model is established to verify the effectiveness of the proposed method. The resistivity calculated by the improved method show that the method can provide initial resistivity values for technicians and improve the convergence and accuracy of current inversion method, which is more suitable for extending to the engineering practice.

Activation energy is popularly used for the estimation of remaining life of transformer insulation. It is defined as the average rate of all reactions that happen with cellulose. Existing literature shows that the activation energy of oil–paper insulation can be obtained from polarization depolarization current (PDC) and return voltage measurement (RVM) data that are measured at a specific temperature. It is practically difficult to ensure the same measurement temperature for both PDC and RVM data. On the other hand, PDC data and its analysis get influenced by de-trapping current. This de-trapping current is generated by ionic charge carriers that get freed from trap sites during PDC measurement process. Formation of these trap sites is related to physical, chemical reactions that happen at oil–paper interface. This paper proposes a methodology which uses de-trapped charge, dislodged from deep and shallow traps, to assess insulation condition and for the prediction of activation energy. Thus, eliminating the need of RVM data. The proposed method is tested using data collected from various real-life in-service transformers.

The effects of moisture, oxygen, and acidity upon the aging of Kraft and thermally upgraded ("Insuldur/spl reg/") papers have been studied in detail. The results for Kraft are consistent with the kinetic model and parameters proposed earlier by Emsley et al., and with the principle that moisture promotes acid-hydrolysis by causing carboxylic acids to dissociate. Moisture is released during the aging of Kraft and, hence, its aging is auto-acceleratory. In contrast, Insuldur consumed moisture under the same conditions, aged more slowly, and its aging was less accelerated by added moisture. 2-Furfuraldehyde (2FAL), which is a dehydration product of pentosans and, hence, an index of moisture production, is also released from Kraft during aging, but not from Insuldur. Acids are, however, produced from both types of paper. Theoretical explanations for these findings are proposed, and their practical implications for transformer maintenance are discussed.

Compared to conventional ac cables, the current rating of HVDC cable circuits is more complicated because the permissible current is not only limited by the operating temperature, but also by the electrical stress within the insulation. Therefore the IEC60287 current rating standard is considered insufficient for some HVDC applications because it fails to include the stress limitation. This paper presents an analytical methodology to calculate an electrical stress-limited rating for HVDC cables, which considers the maximum dielectric stress as the current limiting factor. This paper represents the first part of a project which has comprehensively reviewed cable rating calculations for mass impregnated HVDC cable systems.

Power capacitors are widely used for regulating voltage and improving the power factor of power systems, and the type in most frequent use today are capacitors made of oil-impregnated paper film, a growing number of which will soon have been in operation in the field for 20 years. This has prompted the authors to study techniques for diagnosing deterioration in oil-impregnated paper film capacitors. It was found that thermal stress causes deterioration of the insulating paper, which increases the amount of dissolved CO and CO/sub 2/ in the oil and lowers the partial discharge inception voltage, determining the useful lifetime of the capacitor. Based on this idea, techniques have been proposed for diagnosing deterioration, consisting of caution level and danger level, from actual stress in the field. Further, a trial calculation was made for the number of years and months it takes for a capacitor to reach this caution level, based on an investigation of capacitors in service for many years.

Disconnecting switch operations in gas insulated equipment cause transient voltages with risetimes as steep as 5 to 20 nanoseconds and magnitudes as high as 2.5 pu. There is very little information on the effect of these transients on oil-paper insulated equipment. There have been reports, however of transformer and bushing failures caused by these transients. The electrical breakdown characteristics of oil-paper insulation under steep front impulse were studied in this project, which was co-sponsored by the Canadian Electrical Association and BC Hydro. V/sub 50/ (50% breakdown probability voltage) breakdown data was obtained with steep front (10 ns/2500 /spl mu/s), lightning and switching impulse waveforms. Insulation breakdown voltage vs breakdown time (V-t) data and multiple impulse breakdown data were obtained with the steep front impulse waveform. The V/sub 50/ results showed that the breakdown strengths were lower for steep front impulses than for lightning impulses. The multiple impulse breakdown results showed that oil-paper insulation breakdown strength can be lower than 100 kV/mm. These results are alarming, since they suggest that oil-paper insulated equipment subjected to steep front transients will fail at voltages below the lightning impulse design level (BIL). The volt-time data had a discontinuity. The breakdown process at risetimes below about 50 ns was different from the breakdown process at risetimes above 50 ns. >

In this paper, we discuss a better method to measure the paper water content of transformers using cellulose isotherms. The advantage of the new method is that the transformer oil and cellulosic insulation do not need to be in thermodynamic equilibrium. Instead, the temperature needs to be cycling in order to determine when the direction of water migration, whether out of or into the oil changes. The reversal in water migration can be used to determine the vapor pressure of the water adsorbed by the cellulose. This method was tested using 12 different conditions similar to those within a normally operating transformer. The results showed close agreement when this method is used. The significance is that isotherm equations can now be used even when insulation media are not in equilibrium.

The electrical characteristics and insulation design strength of liquid-nitrogen-impregnated synthetic insulation were considered. The impregnation of liquid nitrogen into insulation paper can be monitored by measuring the electrostatic capacitance of the cable. in tan delta , an index of the dielectric loss, was 0.31% for cellulose paper and 0.18% for semisynthetic paper, polypropylene laminated semisynthetic paper, and biaxially oriented polypropylene laminated paper. It was found that the decline of the thickness dependence of the breakdown strength of the liquid-nitrogen-impregnated insulating cable was steeper than that of the oil-filled cables. It is possible to design the insulation strength of the 66 kV cable to be 10 kV/mm. >

Dielectric testing techniques, in both time and frequency domains, are currently widely used by power utilities for assessment of the condition of transformer oil-paper insulation systems. However, it has been reported that results of these tests are highly influenced by the operating temperature during measurements. The distribution, migration and equilibrium of moisture between oil and paper in a complicated insulation system is highly temperature dependent. It requires adequate experience and proper understanding to interpret the dielectric response results in the presence of temperature variations and thermal instability. Proper analysis of the dielectric test result is only possible with an understanding of the physical behavior of the insulation system in response to temperature. A circuit model, which describes the dielectric behavior of the transformers main insulation system, has been investigated in this paper. The values of the parameters of the model have been identified from the dielectric tests. A correlation has been observed between the operating temperature and the equivalent model parameters that can be used as additional information for better interpretation of the dielectric test results. This paper thus reports a detailed study on the effects of temperature on dielectric measurements of a transformer under controlled laboratory conditions. Some results of practical on-site testing are also presented to demonstrate the possibility of errors that may be introduced in dielectric test results analysis unless temperature effects are taken into consideration.

Knowledge about moisture content in oil impregnated paper insulation is essential when estimating remaining lifetime of power transformers. Direct evaluation of moisture content is rarely possible due to inaccessibility of the internal insulation system in transformers. Therefore, various indirect estimation techniques are utilized. Frequency domain spectroscopy (FDS) measurements of transformer insulation belong to this group. To perform high quality interpretation of results of FDS measurements a good knowledge on dielectric responses in oil impregnated pressboard and paper is required, especially as it refers to their variation with water content and temperature. The aim of this paper is to provide an open access to the frequency domain spectra of oil impregnated paper and pressboard samples, which can then be used in modeling of the results of diagnostic measurements in power transformers.

Dielectric spectroscopy (dielectric response measurements) has been applied for nondestructive estimation of humidity in oil-paper cable insulation. The experiments have been based upon two field-aged cables, 20 and 50 years old. Paper samples from these cables have been characterized and subjected to environments with different relative humidity. Dielectric loss and capacitance have been measured in a frequency range 1 MHz to 1 kHz and related to the moisture content determined by Karl Fisher titration. A method has been verified where the moisture content is correlated to the minimum value of loss tangent (tan/spl delta/). A number of field measurements have been performed where the method has been applied to estimate the moisture content in the distribution cables.

An extensive revision of the IEEE C37.011 "Application Guide for TRV for AC High-Voltage circuit Breakers" has been in process for the last four years. The main aim was to introduce the two- and the four- parameter description of the transient recovery voltage (TRV) as used in IEC Switchgear standards that have been introduced in the revisions of Standards C37.04 and C37.06. These two standards are being concurrently revised, but IEEE C37.011 provides the necessary explanations on TRV characteristic in advance. Non-specialist engineer users of the guide will better understand these standards

For Pt.I see ibid., vol.19, no.1, p.9-14, January 2004. Dynamics of water penetration in mass impregnated cable insulation has been studied. For experimental purposes, artificial damage has been inflicted to a 40-cm-long cable sample and water ingress has been continuously monitored by frequency response measurements. A similar experiment has been conducted on 2.8-m-long cable sample, where both frequency response and time-domain reflectometry (TDR) measurements have been performed. After termination of both experiments, actual moisture content has been measured radially and axially. Based on dielectric measurements, a model of water ingress has been developed and diffusion coefficients have been estimated for mass impregnated cable paper.

Test methods for evaluating flashover voltage of ceramic and nonceramic insulators under ice, snow, and cold-fog conditions are recommended. The paper describes the procedure to be followed at various stages of an evaluation test including preparation of the test object, insulator precontamination, ice, snow, and cold-fog deposits as well as voltage applications and flashover voltage evaluation. Some relevant parameters for ice accretion, flashover voltage evaluation, artificial pollution, and power source requirements are taken from IEC 60129, IEC 60507, and IEEE Std.-4-1995 on standard techniques for high-voltage testing.

Recently developed monitoring-systems show the need as also the possibilities for online- and offline-onsite-diagnostics. The limit in sensitivity for electrical pd-measurements according to IEC 60270 which is reached using filters for sinusoidal disturbances and compensation for corona impulses is still not satisfactory. The acoustic partial discharge measurement (pd-measurement) is also a well known and reliable method often used by transformer manufacturers in testing. In laboratory setups a gain in sensitivity of the acoustic in comparison to the electrical pd measurements could be established. This is reached by adapting the sensors to the propagation path, a modern but moderately priced acquisition hardware and the introduction of new signal processing algorithms. The developed sophisticated measuring systems show remarkable results in online acoustic pd-measurements onsite.