Search

This paper aimed to determine the characteristics of physical and mechanical properties of rice straw hand sheet and investigated the optimal conditions for making rice straw paper. The chemical composition of rice straw determined with the TAPPI standards. The conditions of making paper hand sheet composed of pulping time: 2 hours, 4 hours, pulping temperature: 100°C, 130°C, pulping solvent: 2 wt% NaOH, 4 wt% NaOH and bleaching: unbleached pulp, bleached pulp with 2% H2O2. The paper hand sheet was tested based on TAPPI methods, basic weight TAPPI- T410-om-93, thickness TAPPI- T411-om-89, moisture content TAPPI- T412-om-93, brightness TAPPI T452 om-92, opacity TAPPI standard T 425 om-91, burst strength TAPPI T403 om-97, tensile strength TAPPI T494 om-01, and tear strength TAPPI-T414-om-88. The results showed that the optimal conditions of rice straw hand sheet including pulping time: 2 hours, pulping temperature: 100°C, pulping solvent: 2 wt% NaOH, and bleaching: unbleached pulp gave the highest the physical and mechanical properties form other conditions. This conditions showed as the basic weight 62.27 g/m2, thickness 259.30 µ, opacity 93.34 ISO%, burst strength 64.75 kPa.m2/g, tensile strength 95.33 N.m/g, and tear strength 473.55mN.m2/g. In this condition, the paper hand sheet used at the lowest concentration of pulping solvent and non-bleached, which reduces environmental pollution.

Anode surface plays important role for extracellular electron transfer (EET) of exoelectrogenic microbes in microbial fuel cell (MFC). In this report, the electrochemical performance of a TiO2nanorod array modified carbon paper electrode (TiO2NRs/CP) is greatly improved by controlled chemical etching process. The etching process keeps the array morphology but yields obvious hollows on tops of TiO2nanorods. The etched electrode (TiO2NRs-HOT/CP) exhibits better hydrophilicity than carbon paper (CP) and TiO2NRs/CP electrode as seen from smaller contact angle (CA) and more attached microbes S.loihica PV-4. Meanwhile, the hollows allow higher local concentration of microbial self-secreted flavins that can act as electron mediators for interfacial electron transfer of PV-4 through in-direct pathway. Accordingly, PV-4 produces larger current density at TiO2NRs-HOT/CP electrode with maximum current density of 0.038 mA cm–2, which was much higher than that at CP electrode, and almost five times higher than that at un-etched TiO2NRs/CP electrode.

Panicum repens is a species of grass known by many common names, including torpedo grass, creeping panic, panic rampant, couch panicum, wainaku grass, quack grass, dog-tooth grass, and bullet grass. The paper has been made from non-wood materials for long times. This research was used Panicum repens for made grass pulp as non-wood fiber. The influence of sodium hydroxide (NaOH) concentrations on properties of pulp from Panicum repens was investigated under room temperature. NaOH concentration levels were varied at 0%, 5%, 10%, 15%, and 20%, respectively. Moreover, Paper pulp from Panicum repens was observed by scanning electron microscope (SEM). This research has controlled the length of fiber approximately 0.5-2.5 cm before soaked with NaOH concentration at 1 hour and soak with water for controlled pH value at 7-8. Paper pulp was formed on a sieve. The result showed that color of paper pulp made from Panicum repens was light brown and green. SEM showed that NaOH concentration affects the physical properties of paper pulp. Moreover, true density of paper pulp was also investigated in this research.

In this study, 12 commercially available paper towels were collected from the local market. Their tensile properties were investigated by Kawabata Evaluation System for Fabric (KES-F). Four tensile properties namely: (i) extensibility (EMT), (ii) tensile energy (WT), (iii) tensile resilience (RT) and (iv) linearity of WT (LT) were evaluated. Experimental results revealed that the tensile properties varied within the products. EMT was used as the key property for discussing the tensile properties of paper towels. However, when the different tensile properties were correlated, it was found that WT/RT, WT/EMT and RT/EMT had strong Pearson correlation. In addition, there was no significant statistically relationship between weight and thickness to EMT. Based on this study, it can provide some information about the tensile properties of paper towels in local market which may help the industry for further improving the product quality.

In this study, we chose 12 commonly available paper towels from the local market. The compression properties of the paper towels were examined by Kawabata Evaluation System for Fabric (KES-F). Three compression properties namely: (i) compressional linearity (LC), (ii) compression energy (WC) and (iii) compressional resilience (RC) were examined. The experimental results revealed that the compression properties varied within the different paper towels. RC vlaue was used as the key property for discussing the compression properties of paper towels. When different compression properties were correlated and analysed, it was found that no relationship was noted within different compression properties. On the other hand, there was not significant statistically relationship between weight and thickness to RC. It is hope that the results from this study can help the indurstry to improve the compression properties of paper towels for local market.

In this paper, we collected 12 commercially available paper towels from the local market and their shearing properties were evaluated by Kawabata Evaluation System for Fabric (KES-F). Three properties namely: (i) shear rigidity (G), (ii) shear stress at 0.5º (2HG) and (iii) shear stress at 5º (2HG5) were studied. Experimental results revealed that the shearing properties varied within the products. G was used as the key property for discussing the shearing properties of paper towels. However, in correlating different shearing properties, it was found that 2HG and 2HG5 had strong Pearson correlation. However, no significant statistically relationship between weight and thickness to G was found. This study may provide data for the industry for the improvement of shearing properties of paper towels for local market.

12 commercially available paper towels were collected from the local market and studied in this paper. Kawabata Evaluation System for Fabric (KES-F) was used for evaluating their bending properties. Two bending properties namely: (i) bending rigidity (B) and (ii) bending moment (2HB) were evaluated. Experimental results indciated that the bending properties varied within the products. B was used as the key property for discussing the bending properties of paper towels. When the correlations of different bending properties were investigated, it was found that no significant was found between B and 2HB. However, there was significant statistically relationship between weight and B but no relationship between thickness and B. With the use of the results, the product developer could improve the bending properties of the paper towels.

In this study, 12 commercially available paper towels were collected from the market. Their shearing properties were evaluated by Kawabata Evaluation System for Fabric (KES-F). Three properties namely: (i) coefficient of friction (MIU), (ii) deviation of MIU (MMD) and (iii) geometric roughness (SMD). Experimental results revealed that the surface properties varied within the products. When different properties were correlated, it was found that there was not significantly relationship between MIU, MMD and SMD. However, weight and thickness had well statistically relationship to SMD.

Examples of solid and liquid electrical insulations for power transformer are mineral oil and cellulose based paper. As transformers performed their function to step-up or step-down voltage level, its’ insulations will be degraded. Paper insulation is considered the most critical component in a transformer insulation system because it is not easily replaced if compared to oil where it is easily reconditioned in-order to remove water and contaminants. Studies show that temperature, moisture contents and oxygen contributed to paper insulation degradation. Moisture and furanic compound were produced from these deterioration processes. This paper is focused on the formation and effect of moisture to Kraft paper’s life. Levels of moisture contents were obtained from in-service power distribution transformers. These data then is used to assess the Kraft paper’s life by means of Weibull plot. This study shows that level of moisture contents can be used to assess the life of Kraft paper insulation.

Noise is one of the problems that often occur in urban areas due to the traffic condition. Noise in a building design depends on the choice of materials as sound absorbers. The type of sound dampening material that already exists is a porous material, a resonator, and a panel. The material often used as an absorber is porous materials, because it is relatively cheaper and lighter, especially to reduce the noise in the narrow spaces such as housing and offices. Various substitutes are made from cheap materials, such as the use of recycled materials of egg tray paper with the size of 40 x 40 centimeters. This is a quantitative research that will measure the place of egg tray paper in reducing noise, using a Sound Level Meter. The use of the egg tray paper is able to show an adequate acoustic quality as noise absorbers, with the average value of NR 22-26 dB.

This paper mainly discuss the effect of beating on OCC pulp fiber morphology and paper physical Strength. After the treatment with PFI, the beating degree were ranged from 25 ° SR rises from 56 °SR, the fiber morphologies were greatly changed, and appeared splitting and brooming. Physical results showed that beating can improve strength properties of OCC pulp in the proper degree, 46°SR was the best result in this study.

Noise pollution is a workplace hazard which causes loss of hearing, depending on the sound pressure level and duration of exposure. Because duration of exposure is usually uncontrollable, sound absorbers are used to reduce the value of sound pressure level. A common method to reduce noise is to use porous sound absorbers made out of mineral wools or glass fibres. However, these materials pose health risks and are non-recyclable. This project aimed to fabricate a sound absorber using recycled paper which is in the form of egg cartons as an alternative to the abovementioned fibres. Paper fibres posses high fibre porosity and can be manufactured in a manner which the properties can be easily controlled, making them ideal to be made into sound absorbers. Furthermore, they are biodegradable, do not pose health risks and can be manufactured into different shapes easily. Recycled paper was first turned into pulp, blended and poured into moulds. Different amounts of pulp was compressed until the sample size was approximately 20 mm thick and then dried in a furnace dryer at 600C for 12 hours. The samples were tested using a two-microphone, transfer function impedance tubes according to the ISO 10534-2 standard. Its porosity was determined using a modified wash basin method. The results indicate that the optimum panel has an average noise reduction coefficient, (NRC) of 0.50, which qualifies it to be used as a sound absorbing material. It also encounters its maximum value of 0.98 which occurred at the 1575-1675 Hz range. When compared to other materials, recycled paper has similar properties as coir fibre and is quite comparable to other commercial sound absorbers at the same thickness.

In order to satisfy the strong demands of learning paper-cut from the public and paper-cut lovers and the needs of art education and training to practical ability for children and teenagers.Taking full use of the advantages and features of 2D interactive animation, we designed and implemented a virtual interactive system based on the classification of paper-cutting technique. Learners without paper-cutting experience can master the basic techniques of paper-cutting, and appreciate the integrity of the production process of paper-cutting through this system, which will promote the inheritance and development of folk paper-cut product techniques.

In order to study the corresponding relationship between the design and fashion of tea gift package, this paper will analyze and discuss the color design and packaging style of tea gift package. Besides, this paper will also do research on the cultural origin of tea and the value of package, and analyze the influence of package on consumers. Finally, based on the research, the author had design a tea gift package that is in accordance with the current trend. This study uses bright yellow and orange as predominant colors to present nobleness of tea of Alishan. The colors used on the packaging will render people associate with harvest in autumn.

The quality of product of manufacturing industries depends on dimension accurately and surface roughness quality. There are many types of surface defects and levels of surface roughness quality. Ironing process is one type of metal forming process, which aims to reduce the wall thickness of the cup-shaped or pipes products, thus increasing the height of the wall. Manually surface inspection procedures are very inadequate to ensure the surface in guaranteed quality. To ensure strict requirements of customers, the surface defect inspection based on image processing techniques has been found to be very effective and popular over the last two decades. The paper has been reviewed some papers based on image processing for defect detection. It has been tried to find some alternatives of useful methods for product surface defect detection of ironing process.

This paper presents the performance investigations of the spatial domain image watermarking for camera-captured images on different types of printers and printable materials. We examine the effects of our previous watermarking method based on the modification of image pixels on three types of printers, i.e. inkjet, laser and photo printers, and four different types of printing papers, i.e. uncoated, matte, glossy and semi-glossy papers. In the experiments, the DSLR camera is used as tool to capture the printed watermarked images, while the image registration technique based on projective transformation is used to diminish the RST and perspective distortions in the captured image. The performances in terms of extracted watermark accuracy at equivalent watermarked image quality on different types of printers and printing papers are measured and compared.

The novel flexible pressure sensor with skin-like stretchability and sensibility has attracted tremendous attention in academic and industrial world in recent years. And it also has demonstrated great potential in the applications of electronic skin and wearable devices. It is significant and challenging to develop a highly sensitive flexible pressure sensor with a simple, low energy consuming and low cost method. In this paper, the silver nanowires (AgNWs) as electrode material were synthesized by polyol process. The polydimethylsiloxane (PDMS) was chosen as a flexible substrate and polyimide (PI) film as dielectric layer. The AgNWs based electrode was prepared in two methods. One is coating the AgNWs on photographic paper followed by in situ PDMS curing. Another one is suction filtration of the AgNWs suspension followed by glass slide transfer and PDMS curing. Then the capacitive pressure sensor was packaged in a sandwich structure with two face to face electrodes and a PI film in the middle. The sensitivity of the sensor as well as the micro-structure of the electrodes was compared and studied. The results indicate that the roughness of the electrode based on AgNWs/PDMS micro-structure plays an important role in the sensitivity of sensor. The as-prepared flexible pressure sensor demonstrates high sensitivity of 0.65kPa-1. In addition, the fabrication method is simple, low energy consuming and low cost, which has great potential in the detection of pulse, heart rate, sound vibration and other tiny pressure.

Magnetic stripe cards and magnetic recording paper are commonly used in credit cards, identity cards, and transportation tickets. Barium ferrite was used to prepare magnetic inks and the magnetic ink was coated onto the paper substrate to obtain the magnetic papers. The crystal structure of barium ferrite was characterized by X-ray diffraction (XRD) and the magnetic property of barium ferrite was tested by vibrating sample magnetometer (VSM) The performance of the magnetic recording paper and the surface morphology of the coating magnetic layer were also characterized. The results show that the magnetic ink based on barium ferrite with the formula of 41wt% of the barium ferrite powder, 14wt% of polyurethane, 36wt% of solvent and 9wt% of PVP has good printing characteristics and the magnetic recording papers have good performance.

There are too many waste that has the capability in undermine the environment, including paper waste. The unused paper waste collected from one office only could reach two tons a year. To decrease the possibility of paper waste in ruining the environment, it can be recycled to be any usable things. One example is recycle the paper waste into paper brick as building material. Before the brick can be used, it needs to be tested whether it can create a thermal comfort or not. So the objectives of the research are to find the ability of paper brick in create thermal comfort, and compare it with the red brick that is commonly used by people. The method used in this research is field measurement using model and hygrometer as a tool. The result of the research is that the paper brick can create a thermal comfort in some hours of a day. But it turns out that it is not better than the red brick in decreasing the outside temperature. The temperature inside the building with a red brick is lower that the temperature in the building with the paper brick.

Peer review is a new phenomenon in the process of internationalization of academic journals, but also a worldwide problem. In this paper, the development and practical application of peer review system are sort out, which are based on objective data research of domestic and international academic journals; the problems of network online published papers in practice are analyzed and explored by modern advanced network technology as the application tool, and how scientific orientation are they to play an effective role. The purpose of paper is in order to ensure the impartiality of the academic council, spread rapidly and use information resources, and further promote to enhance the overall level of academic journals.

The restoration of regular paper fragments can be solved by edge matching. Edge matching is based primarily on the length and location of the break in writing, however, it is possible that the edges of some regular paper fragments are blank. And so the error of restoration is the inevitable. In this case, it needs manual intervention based on the article content and then eliminate errors. Prior to the establishment of a mathematical model, there is a need for binarization of regular paper fragments with Matlab, then establish vector space model and construct edge contrast matrix, get the order after the Q cluster analysis of fragments. Finally the original picturecan be obtained through splicing and restoring in the order.

Tea has been a popular beverage since ancient time and accumulated a great deal of culture. In modern society, tea packaging design attracts a lot of attention. How to reflect the integration of traditional culture and modern culture from the perspectives of shape, pattern and color and cater to consumers needs at home and abroad and make the tea packaging fun has become the key of tea packaging design. The important function of packaging is to attract consumers’ attention and trigger their desire to buy the product. Through the visual design of packaging, it is a vital way to reflect the quality of tea, as well as increase the value of goods. Highlighting the characteristics of tea is the fundamental purpose of packaging. The color, pattern and text attribution are essential element in packaging, meanwhile it conveys the product information. The application of color, pattern and text and other factors in the study make the tea more competitive. It exchanges information between tea and consumer. Good tea packaging can not only improve sales, but also enhance the brand image, and expand spread of traditional tea culture.

In this paper, Genetic Algorithm (GA) method has been applied in the moisture control system for auto tuning (PID) parameters. Proportional – Integral – Derivatives control scheme is used to provide an efficient and quiet easier in control engineering applications. Most of the PID tuning methods are used as manually which is difficult and time consuming. Genetic Algorithm which leads to improve the efficiency of tuning of process. The proposed algorithm is used to tune the PID parameters and its performance has been compared with Fuzzy logic techniques.Compare to the fuzzy logic technique dynamic performance specfications such as rise time, peak time and peak overshoot optimal values produced by GA. The plant model represented by the transfer function is obtained by the system identification tool box.

For the regular rectangular paper scraps recovery problem, at first, I used the edge detection based on the improved wavelet analysis to numerically describe the outline of words on each of the pieces. Secondly, screening according to the line spacing to find out paper scraps which are located in the edge. Thirdly, do initial matching to select the best line as a benchmark for two-dimensional double match splicing. At last, I used two-dimensional double match to make the whole stitching come out. In this paper, the data would use the 2013 China National University Mathematical Modeling Competition topic B official data. The model not only can solve the problem of this article, also can be used to solve the problem of similar cutting conditions.

The restoration of regular paper fragments can be solved just as the Traveling Salesman Problem. Paper pretreatment and edge matching are the main steps during the restoration process, which contain binarization, screening between the left and right boundary depending the width of paper margins. For some longer paper fragments, the transverse splicing can be realized with Greed Algorithm. But the algorithm will get a non-ideal restoration for more fine paper fragments. Therefore the noise-suppressed processing before clustering from line to line through projection is essential in order to make sure that the regular English fragments can get the regularity like Chinese characters. The two experiments get an 100% correct rates when using the method combining the improved genetic algorithm for traveling salesman problem.combining the improved genetic algorithm for traveling salesman problem.

An effective method of trajectory reconstruction is presented in order to identify aerodynamic parameters. A novel smoother URTSS, which can get more optimal ballistic parameters, is introduced because of the biggish error caused by the uncertain initial conditions. Finally the validity of the method is verified by the experimental data. It also proves that URTSS can improves the accuracy of the identification of aerodynamic parameters.

It was found that slagging in high temperature zone is one of the major problems in the refinery, petrochemical, pulp and paper, and steel industries; especially in biomass and coal pulverized power plant. Slagging conditions are critical factors influencing reliability and availability on a biomass utility boiler. In this study, several types of slagging were collected for chemical analysis. It was revealed that the chemical composition and other properties of received slagging showed unique results based on the type of feedstock fuel materials.

India is a fastest growing major economy in 2018, with a growth rate of 7.4 per cent GDP. Energy use in developing countries like India has risen more than fourfold over the past three decades and is expected to continue increasing rapidly in the future. Energy is essential for a economical growth of any county. Biofuels derived from renewable resources will become a alternative supplement for the conventional energy sources in meeting the increasing requirements for transportation fuels. In the present paper, effort are made to evaluate the pongamia biodiesel of 20% Blend (PB20) with neat diesel as an alternative fuel for CI engine. The pongamia oil is converted into pongamia methyl esters (Biodiesel) using two step process Esterification and Transesterification. The fuel properties of raw pongamia methyl ester and blend (PB20) are evaluated as per ASTM/BIS standards to check their feasibility as an alternative fuel. The prepared blend is used to run the computerized CRDI diesel engine at different load conditions. From the experimental investigation made, PB20 has a potential to be as an alternative fuel for diesel engine. The performance of PB20 with respect to Brake Thermal Efficiency (BTHE), Mechanical Efficiency, Brake Mean Effective Pressure (BMEP) and Specific Fuel Consumption (SFC) is comparatively low when compared to neat diesel. The P-Ɵ and P-V diagram shows that the combustion of PB20 is as similar to that of neat diesel.

Ramie solid waste as chips can be used as raw material for pulp. Ligninolytic enzymes of laccase widely used for pretreatment of the pulping process of ramie chips by biodelignification using laccase produced byPenicilliumsp. LX/08 has been done. This study aims to obtain optimal concentrations of lignin and CuSO4as enzyme inducers to increase laccase production fromPenicilliumsp. LX/08 during biodelignification process and its effect on the quality of ramie pulp. The biodelignification process of ramie chips was carried out by solid state fermentation (SSF) method with six days incubation time. Two inducer type treatment factors (CuSO4and lignin), and variations in the concentration of each lignin (0.25 g/L, 0.5 g/L, 0.75 g/L) and CuSO4(0.25 mM, 0.5 mM, 0.75 mM) were investigated in this study. The pulping process was carried out by the soda process in a digester under conditions: 12% active alkaline, temperature of 165°C for 3.5 hours. The results showed that 0.75 mM and 0.5 g/L of lignin were the optimal concentrations which could increase the laccase activity ofPenicilliumsp. LX/08 by 343 U/L and 25,8 U/L, respectively. The quality of ramie pulp showed a decrease in Kappa Number of 9,34% with an increase in pulp yield to 55,43%. Based on these results, the pretreatment method using laccase produced byPenicilliumsp. LX/08 can assist the pulping process of ramie.

Spent catalyst is listed as one of the hazardous wastes. Based on the toxicity characteristic shows that spent catalyst contains some heavy metals at concentration above the regulations limits. This situattion becomes an important issue in nowadays. In this research, fungus Aspergillus niger was investigated to produce weak organic acid (citric acid). Batch experiments were performed to compare the leaching efficiency from spent catalyst of pulp density (2% and 4%) and particle size (212 µm, 150 µm and 75 µm). Result showed that after direct bioleaching process, maximum recovery of valuable metal 24.94%, 7.42%, 1.09%, 3.51%, 4.87% and 1.66% were achieved for aluminum, calcium, iron, copper, silver and platinum respectively at 2% pulp density. Overall data shows that metal recovery at pulp density 2% are higher than 4% pulp density. The maximum recovery based on particle size shows that the smaller particle (75 µm) the higher metal recovery (Al, Ag and Pt) and for some metals was different such as Fe, Cu and Ca.

In this paper, the cockle shell was studied as a catalyzer for biodiesel production. The cockle shell was heated at the various temperatures from 200 to 1300 °C for 4 h in the furnace. Then, the crystal structure and function group of unheated and heated cockle shell were characterized by X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR), respectively. The results indicated that the initial phase of cockle shell is aragonite phase. After heat at 400 °C, the aragonite phase transformed to calcite phase. Moreover, the calcite phase of cockle shell was completely changed to calcium oxide (CaO) after heated at 800 °C. Eventually, the yield of biodiesel used the CaO derived from cockle shell were determined by nuclear magnetic resonance spectroscopy (NMR). The results show that the CaO derived from cockle shell can be used as a catalyzer of biodiesel preparation. However, the biodiesel used CaO from cockle shell after heated at 1100 to 1300 °C as a catalyzer have the higher yield than other heated temperature. Finally, the results of this research indicated that the CaO from cockle shell could be used as a catalyst for biodiesel production.

Biomass fly ash is an ash combustion product. It is composed of the particulates (fine particles of fuel) driven out of biomass-fired boilers together with the flue gases. The understanding of the behaviour and property of fly ash is very important in order to predict the consumable part lifetime inside industrial boiler system. In this research study, the several characterization processes were carried out. It was revealed that biomass fly ash obtained from different sources presented unique property and more results were displayed in experimental result section.

This study was carried out to investigate the characteristics of pulp and paper produced from oil palm oil male flower spikes (OPMFS). The evaluation of the pulping process was studied based on the chemical Soda Anthraquinone pulping process. 60 gsm papersheet of oil palm male flower spikes were prepared from unbeaten and unbleached OPMFS Soda-AQ pulp. All optical, physical and mechanical characteristics were investigated according to TAPPI and MS ISO standards. OPMFS pulp recorded value of 6.42 s, 353 ml, 76.5 %, 36.7 % and 9.35 for drainage time, freeness, moisture content, screened yield percentage and Kappa number respectively. OPMFS paper sheet recorded value of 56.99 g/m2, 131.11 µm and 0.43 g/m3for grammage, bulking thickness and apparent bulk density respectively. Unbleached OPMFS paper also recorded 26.49 % and 43.50 % for brightness and opacity. For mechanical characteristics, OPMFS paper recorded 39.10 N.m/g, 8.32 mN.m2/g, 3.15 kPa.m2/g and 38.50 for tensile index, tear index, burst index and folding endurance (no.) respectively. This research demonstrate some potential characteristics of oil palm male flower spikes (OPMFS) paper to be investigated as a newly explored non-wood based raw material for papermaking.

In the paper experiments and theory of biogas production using industrial waste from paper production as a co-substrate are described. The main aim of the experiments was to evaluate the sensitivity and applicability of the biochemical conversion using the anaerobic digestion of the mixed biomass in the pilot fermentor (5 m3), where the mesophillic temperature was maintained. It was in parallel operation with a large scale fermentor (100 m3). The research was carried out at the biogas plant in Kolíňany, which is a demonstration facility of the Slovak University of Agriculture in Nitra. The experiments proved that the waste arising from the paper production can be used in case of its appropriate dosing as an input substrate for biogas production, and thus it can improve the economic balance of the biogas plant.

The goal of the paper is to determine a possibility to use methyl cameline esters and their mixtures with diesel oil (in ratios of 95:5, 90:10, 85:15, and 80:20) as fuels for compression-ignition engines (diesel engines). The cameline esters obtained in the result of one-step basic transesterification were characterised in respect of kinematic viscosity at 40°C, density at 15°C, acid number, solid impurities content, sulfur content, ignition temperature, temperature of cold filter clogging, and oxidation resistance at 110°C. It was shown that majority of factors of pure cameline esters analysed in the paper, excluding content of impurities and oxidation resistance, met the requirements of the PN-EN 14214, 2012 standard. Whereas, in case of mixtures of diesel oil with varied addition of esters, it was ascertained that 5, 10 and 15% addition of the biocomponent did not affect significantly the physico-chemical properties of the prepared fuel. In turn, the highest, 20% share of a cameline ester caused a slight increase in viscosity, density, content of impurities and ignition temperature of the obtained mixture. However, it is noteworthy that these factors did not exceed the acceptable values according to the standard. In general, it was also ascertained that the only parameter disqualifying use of these samples as a fuel for compression-ignition engines was too high content of impurities.

The aim of this work was to study the potential of the agricultural waste byproduct as a low-cost adsorbent for removal of phosphate ion (PO43-) from synthetic wastewater. The simple preparation of carbonized filter cake (CFC) was performed at 550°C. CFC was also characterized using FTIR, X-ray fluorescence analysis. The adsorptive parameters of batch experiment, such as pH of solution, dosage and contact time were systematically studied in order to the optimization condition. The optimum conditions of pH, contact time and adsorbent dose were to be 6, 60 min, and 2 g/L, respectively. The Langmuir and Freundlich isotherms were used to calculate the adsorption parameters that was able to describe the equilibrium isotherm and adsorptive mechanism. The maximum monolayer adsorption capacity of CFC was estimated as 20.32 mg/g. The optimized condition was applied for phosphate removal from synthetic wastewater. The achieved phosphate removal efficiency from synthetic wastewater sample was to be 92.4%. Filter cake is a low-cost byproduct of sugar cane but it can also highly effective remove phosphate ion from aqueous solution. The modification of filter cake surface via chemical reaction as a new adsorbent in order to increase surface sites and high affinity with phosphate ion will also be further studied.

This study used a sodium hydroxide (NaOH) solution to activate a mixture of water treatment sludge, fly ash, and slag, in order to produce a new alkali-activated controlled low-strength material (CLSM). Fresh properties of this new CLSM were investigated through the tests of workability, setting time, and ball drop time. Test results show that the addition of water treatment sludge (WTS) decreased workability. In addition, the addition of such WTS increased initial setting time and ball drop time, whereas the alkali equivalent (AE) shortened the initial setting time and ball drop time. At a liquid-to-solid ratio (L/S) of 0.9, a WTS content of 10%, and an alkali equivalent of 9%, the fresh properties for the CLSM conforms to the design principles and provisions of the Public Works Department, Taipei City Government, and is ideal for road construction in order to reduce traffic impact.

The depleting Fossil fuels reserves are caused to look into new Renewable energy sources to fulfill Diesel fuel demand in developing countries such as India. Increasing urbanization is lead to the search for new alternative sources like biodiesel. In India demand of diesel fuel in Industry and Transportation sector. To resolve all the above problems, researchers, scientists were produced biodiesel from first, second and third generation biodiesel sources. Among all the sources Algae was the most Oil rich sources. The byproducts in algae to biodiesel conversion process are most valuable than other. In the present work author tried to work in a new approach, i.e. the mixed culture algae particles are emulsified in pure Coconut biodiesel fuel by using TritonX-100 as a surfactant to prepare an emulsified fuel. This fuel sample was applied to DI CI engine to improve performance, emission characteristics. The experimental results were shown that there is the improvement in diesel engine performance; emission characteristics especially break thermal efficiency and NOx emission reduction than diesel fuel due to its clean combustion.

Biomass-derived materials such as kenaf pulp and wood chips are a perfect candidate to produce magnetic paper. Furthermore, by using biomass waste, such as paddy straw, sugarcane, bagasse and durian shell, the cost of producing magnetic paper can be further reduced while giving added value to the waste. This paper investigates the potential of producing magnetic sheet from durian shell. Initially, durian shells were dried before undergoing the pulping process. The resulted sheet was then combined with magnetic particles, the nano magnetite using either lumen loading or in-situ co-precipitation to produce a magnetic composite sheet. After being loaded with magnetic particles, the composite sheets were tested in terms of the homogeneity of the magnetic particles in the samples, degree of loading of the magnetic particles and the magnetic properties of the samples. Results obtained show a great success in producing the magnetic sheet from durian shell waste and nano magnetite particles. It was also found that the lumen loading method gives better magnetic properties compared to the in-situ co-precipitation method.

In this study a high viscous liquid fuel, approximately 20 times more than that of diesel, produced from non- edible oil seed jatropha curcaswhich has been considered as an alternative fuel for the compression ignition engine is reduced through trans-esterification process. During this process, the raw jatropha curcas oil is preheated to 60°C and treated with methanol 20% by volume along with potassium hydroxide (KOH) by 0.568% of the oil weight as alkaline catalyst at 60°C reaction temp to produce Methyl Esters of Jatropha Oil (JOME). Similarly, the above method is followed to produce Ethyl Esters of Jatropha Oil (JOEE) with preheating at 70°C. In addition, 2% glycerol is added to the mixture to improve the reaction rate. The lower viscous fuel biodiesel (JOME and JOEE) produced by trans-esterifying of jatropha oil is blended with pure diesel 50% by volume. An experimental investigation have been carried out without altering the CI engine to examine the performance parameters in terms of brake thermal efficiency, total fuel consumption and brake specific fuel consumption for several engine load from 0 Kg to 8 Kg. The study also includes, separation of crude biodiesel from glycerol, washing of crude biodiesel, examination of calorific value using bomb calorimeter, viscosity measurement using redwood and brookfield viscometer, engine emission test and cost comparison for production of one litre of JOME and JOEE. It is inferred from the above study that the blends of JOME with diesel have closer performance to diesel when compared to the blend of JOEE with diesel. But, on comparison of their exhaust emission, the JOEE showed reasonable lower exhaust emission CO and NOx in spite of its higher calorific value when compared with JOME. The study also revealed that the biodiesel can be adopted as an alternative fuel for existing diesel engine without any modification.

Natural indigo dye was applied on silk fabric by using pad-batch and pad-dry techniques in the present of thiourea dioxide and sodium hydroxide. Alum (AlK(SO4)2), ferrous sulfate (FeSO4), and stannous chloride (SnCl2) were used as mordants. The colour of each dyed fabric was investigated in terms of the L*, a*, b* and K/S values. The effects of different dye concentrations with the use of applying padding techniques in the dyeing process was investigated. The colour fastness to washing, light, rubbing, water, and perspiration of dyed silk fabrics was performed according to the present ISO standard. Silk fabric was dyed by using a natural indigo colourant, applying one with metal mordant and one without giving the silk fabric a blue shade. However, a greenish blue shade was found as a dyeing result by adding a ferrous sulfate mordant. The fastness properties of washing, water, perspiration, and rubbing were very good level. However, a fair rating level was observed using a light fastness dyeing technique.

Soil contamination with used lubricating oil from automobiles is a growing concern in many countries, especially in Asian. This research was conducted on a laboratory scale. The plant used in this research was Spathiphyllum spp. in comparison with controlled (no-plant). The size of reactor used in this research was set at 20 cm width, 20 cm length, and 40 cm height with working volume of the reactor was 0.016 cm3. Moreover, a pH value was controlled in a range of 7 to 8. The soil contaminated with used lubricant oil collected from automobile shop in Nonthaburi province. Soil contaminated and treated soil were extracted by solid-phase extraction (SPE) and analyzed by gas chromatography with mass spectrometer (GC–MS). The results showed that Spathiphyllum spp. could be growth during time operation. Spathiphyllum spp. has a potential in reclaiming hydrocarbon-contaminated soil such as Benzene, Toluene, Ethylbenzene, and Xylene (BTEX) approximately 20 to 60 days operation.

Spent coffee grounds (SCGs) are created in a large amount as a processing waste during making the coffee beverages. Due to its properties, this waste is attractive for different applications such as biofuel production, antioxidant capacity, and renewable materials. In this study, the SCGs were firstly washed by distilled water to remove impurities and contaminations. The washed SCGs were dried in an electric oven at 120 °C for 24 h. The dried SCGs were carbonized at various temperatures from 600-1400 °C for 4 h in normal atmosphere by electric furnace to produce the SCGs powders. The as-received powders were characterized to obtain composed elements and phases by Energy-dispersive X-ray spectroscopy (EDX/EDS) and X-ray diffraction (XRD), respectively. X-ray analysis results indicated that the obtained SCGs powders were dominated by carbon-rich phase with stronger bonding at higher carbonizing temperature. This finding was recommended that the SCGs could be considered as a possible candidate of the environmentally friendly materials to prepare and develop the biomass fuel generation.

The plywood production from coconut coir fiber and water hyacinth was investigated to reduce the residue and be increased of value and to reduce the use of natural wood by using coir and water hyacinth which are pressed to be plywood production. LA - 35A TOA glue and natural powders were used for plywood adhesive. The plywood tests were found in this research. The water absorption, density, and bending strength test as per Japanese Industrial Standard (JIS A 5905) were evaluated in this research. The results showed that coconut coir fiber was suitable for plywood production and contained 1.93 percent of moisture content, 0.52 g per cm3 of density, and 86.5 percent of water absorption and 11.9 MPa of bending strength. The result showed that water absorption value of plywood made from coconut coir fiber and water hyacinth was quite high and this product suitable for use only indoor furniture. Moreover, these research was studied the biodegradation of plywood products that made from coconut coir fiber and water hyacinth.

Many machining operations e.g. turning, milling or grinding are dependent on the application of water-based metalworking fluids (MWF) which contribute significantly to their high level of performance. MWF in-use are exposed to a microbial contamination, which leads to a deterioration of water-based MWF components and can cause a premature failure of the whole coolant system. Expensive monitoring and the addition of biocides are needed to maintain the MWF quality and to reduce the microbial load, regardless of the potential risk for health and environment. To overcome these limitations, the paradigm shift of using microorganisms as a replacement for conventional MWF is investigated in this paper. Microbial cell components and some microbial inclusions are comparable to conventional MWF components like e.g. fatty acids or sulfur compounds. Due to this fact, it is possible to create a regenerative system on a microbiological basis for the substitution of conventional MWF components. In preliminary tribological investigations the basic lubrication properties of microorganisms and their potential as a replacement for conventional MWF were shown. The presented approach intends to investigate the influence of microbial cell counts, cells size and extracellular polymeric substances (EPS) on the lubrication behavior respectively. The results of the tribological tests show that especially microorganisms with a big cell volume or a high EPS productivity exhibit superior Brugger-values (up to 174%) compared to a highly concentrated conventional MWF (emulsion 10%) and indicate the great potential of microorganisms as a replacement for conventional MWF.

Searching for new sources of energy in order to minimize the dependence on fossil fuels and also to preserve the environmentmeets thenecessityfor finding effective solutions to the problem of waste generated in different production levels.In juice pulp processing industrylarge volumes of waste are produced daily and can contribute, with its burning, for energy production. Once it is necessary the removal of moisture from the residue, this study evaluate the conventional drying and microwave drying of the biomass generated by peels of orange, mango and passion fruit with initial mean moisture content higher than 75%. The experiments were performed in oven at a temperature of 150°C and the average time for an almost complete withdrawal of peels studied was 130min. For drying by microwave with power of 900W, the average time required for the total reduction in moisture was 8.5min. The drying Page model was adjusted by non-linear regression to data obtained with correlation coefficients in all cases greater than 0.955. The higher heating value was rated equal to 16,25kJ/g, 19,62kJ/g, 16,35kJ/g for the peels of orange, mango and passion fruit, respectively. The average energy consumption for the drying process in the oven was 81,25kJ/gevaporated water and 12,07 kJ/gevaporatedwaterin the process by microwave, which indicates that drying using microwave is a very interesting option.

Heat treatment is one of the environmental friendly ways to treat timber that will lead to the improvement of timber natural quality and equip the timber with new properties. It is an eco friendly and alternative treatment method that will modify the properties of timber by using high temperature instead of using chemical preservatives as common practice. This paper presents the effect of heat treatment on physical properties which is density for two types of Malaysia hardwood namelykapurandkeruing. Specially design electronic furnace was used as an oven for the heat treatment process. The result shows a reduction in density after heat treatment, however the difference is not merely significant. Lower in density indicates a weight loss which theoretically caused by moisture content loss thus leading to the increment of movement stability.

In recent years, there have been a number of interests on the Palm Oil (PO) and Coconut Oil (CO) as a potential alternative dielectric insulating fluid in transformers which stimulate different types of studies on these oils properties. Among the important studies is the lightning impulse properties. This paper presents the investigation on the lightning impulse breakdown voltage of PO and CO under non-uniform electric field. The PO used in this study is Refined, Bleached and Deodorized Palm Oil (RBDPO) Olein type. The influence of the testing methods, rising-voltage and up-and-down are investigated at 2 gap distances for both oils. It was found that the lightning breakdown voltage performance for some of the RBDPO and CO are comparable to MO.

A portable electronic nose (e-nose) using low-cost dynamic headspace and commercially metal oxide gas sensors has been developed. This paper reports evaluation on the performance of the e-nose to classify vegetable oils (sunflower and grape seed oils) and animal fats (mutton, chicken and pig fats). The e-nose consists of a dynamic headspace sampling, a gas sensor array and a real-time data acquisition system based on ATMega-16 microcontroller. The dynamic headspace can divided into two chambers, i.e. sample and gas sensor array room. It is also equipped with three small fans for adjusting sensing and purging processes. Principal component analysis (PCA) was used for measurement data analysis after all features being extracted. The first two principal components were kept because they accounted for 91.1% of the variance in the data set (first and second principals accounted for 72.9, 18.2% of the variance, respectively). This results show that the e-nose can distinguish vegetable oils and animal fats. This work demonstrates for the future that the e-nose with low-cost dynamic headspace technique may be applied to the identification of oils and fats in halal authentication.

‘Sonication - cryptic growth’ technology can reduce 30-80% excess sludge in wastewater treatment systems. Various mechanisms contribute to the sludge reduction but the role of each one is unclear. This paper quantitatively studied the potential mechanisms in ‘sonication - cryptic growth’. The operation condition was: every day 20% sludge was sonicated under 1.2 Wml-1 for 15 min and then returned to the wastewater treatment reactor for cryptic growth. The results showed that under such conditions, ‘sonication - cryptic growth’ reduced the excess sludge by 57.3% and the effluent met the national discharge standard. Multiple mechanisms were involved in the process. Detailed analysis showed that the ‘lysis-cryptic growth’ mechanism was the most important one and accounted for 49.1% of sludge reduction. Biodegradation of residual sludge was the second important one and contributed 19.5%. Other potential mechanisms included the altered microbial community, longer sludge retention time, and accumulation of persistent materials. But organic load increase had virtually no impact.