Search

Publisher Copyright: © 2022, The Author(s). Direct fire, indirect heat, and extinguishing water cause great damage to cultural assets upon a fire disaster in a library or archive. Conservation and restoration of heat-damaged papers are particularly challenging due to the complexity and severity of the damage. Since valuable originals obviously cannot be used for the development of treatment methods and only to a limited extent for the analysis of the damage, it is necessary to produce model paper materials that have a high degree of similarity to fire-damaged papers, which was addressed in the present study. Three different heating methods were tested to produce model papers of different heating levels. Their altered optical, structural, and chemical properties were analyzed and compared with the results of original fire-damaged samples. The study points out pathways to enable the production of comparable sample materials. Heating between hot plates or in an oven produces papers that have properties quite similar to the originals in terms of surface area, paper structure, cellulose integrity, and interactions with water. Stack heating in the oven has proven to be a particularly effective manufacturing method for larger quantities of model papers.

This column is intended to address the kinds of knotty problems and dilemmas with which many scholars grapple in studying health professions education. In this article, the authors address the question of why papers may be desk rejected (rejected without going out for formal peer review) and describe simple steps for authors to optimize their work so it gets past the desk reject stage. Submitted/Accepted version

A series of new coloring materials in nanoscale based on 5-(2-aminothiazol-5-yl) thiazol-2-amine and 5-(4-aminophenyl) thiazol-2-amine were synthesized. The nanoscale pigments were prepared using a grinding high˗energy ball-milling technique. X-ray diffraction and transmission electron microscopy were employed to determine the particle size of the nanoscale pigments (40–80 nm). The synthesized pigments in normal and nanoscale were applied in the printing of polyester fabrics. The fastness and colorimetric properties of the printed samples were carefully studied. Additionally, the synthesized pigments were applied as water-based flexographic ink for paper and carton. The hue of the color pigments L*, a*, b*, glossiness, and fastness to light were measured. The comparison of the new heterocyclic benzidine analogs in normal and nanoscale with commercial benzidine pigments demonstrated better results, particularly for the nanoscale pigments.

SummaryInhibitors of the cyclin-dependent kinases 4/6 (CDK4/6i) have been practice-changing and are now considered the standard of care in combination with endocrine therapy for the first- or second-line treatment in advanced hormone-receptor-positive, human epidermal growth factor receptor 2‑negative breast cancer. Recently, CDK4/6i have also emerged as an appealing targeted cancer therapy in early breast cancer, however results of large clinical trials are controversial. This position paper summarizes the evidence, and provides guidance for clinical practice.

In this work, we present for the first time, a simplified fabrication of a laminated paper-based analytical device (LPAD) with a free-mobile app, Palette Cam, for image analysis. A filter paper is cut in a rectangular shape (9 × 3 cm) and placed between a top laminating sheet with punched holes and a bottom laminating sheet. The holes allow accessibility of liquid on the paper. Thermal lamination is then employed to complete the fabrication of LPAD. Our simplified design reduces a tedious alignment of small pieces of paper to the holes. We demonstrated the LPAD with an analysis of salicylic acid in pharmaceutical products. Each 4 μL of ferric reagent and sample was dispensed on the LPAD. Smartphone was used to capture images. The RGB (red green blue) color intensity from the Palette Cam was converted into a logarithm color ratio. Our LPAD is simplified, cost-effective and able to be a portable device.

Organic sticky contaminants represent one of the biggest technical challenges in the paper recycling process. These contaminants reduce paper strength, cause plugging of wires and felts, and stick to or deposit on machine parts affecting the runnability of the paper machine. The removal of these sticky contaminants is difficult to achieve along the process due to the heterogeneous nature of these organic contaminants. In this study, the nature of sticky contaminants in multiple wastepaper grades was analyzed and characterized using screening, solvent extraction with subsequent analysis such as FT-IR, GC-MS, and SEM. The content of stickies in wastepaper varies among different paper grades and their recovery methods. The majority of wastepaper grades collected from a recycled paper mill contains 3–5 wt% stickies, while a sample from a curb side collection from a residential area contains about 15 wt% stickies. Polyvinyl acetate (PVA) polymers, styrene butadiene rubber (SBR), paraffin waxes and polyamines are the major components in the extracted sticky contaminants. In addition, these stickies deposit heavily on fibers surface leading to high negative charge in fibers suspension ranging between 2 ~ 4.5 µeq/L. It is expected that these findings will assist addressing the knowledge gaps in understanding the nature of stickies and their behaviors, and to eventually develop highly efficient technologies for contamination removal in the paper recycling process.

Apart from protecting the environment from undesired waste impacts, wastewater treatment is a crucial platform for recovery. The exploitation of suitable technology to transform the wastes from pulp and paper industries (PPI) to value-added products is vital from an environmental and socio-economic point of view that will impact everyday life. As the volume and complexity of wastewater increase in a rapidly urbanizing world, the challenge of maintaining efficient wastewater treatment in a cost-effective and environmentally friendly manner must be met. In addition to producing treated water, the wastewater treatment plant (WWTP) has a large amount of paper mill sludge (PMS) daily. Sludge management and disposal are significant problems associated with wastewater treatment plants. Applying the biorefinery concept is necessary for PPI from an environmental point of view and because of the piles of valuables contained therein in the form of waste. This will provide a renewable source for producing valuables and bio-energy and aid in making the overall process more economical and environmentally sustainable. Therefore, it is compulsory to continue inquiry on different applications of wastes, with proper justification of the environmental and economic factors. This review discusses current trends and challenges in wastewater management and the bio-valorization of paper mills. Lignin has been highlighted as a critical component for generating valuables, and its recovery prospects from solid and liquid PPI waste have been suggested.

The membraneless-gas separation microfluidic paper-based analytical device (ML-GS μPAD), consisting of donor, spacer, and acceptor layers, was developed to monitor total ammonia in fish pond water. The principle of the analysis involved the addition of sodium hydroxide solution to the sample zone in the donor layer containing ammonia/ammonium, and the produced ammonia gas diffuses through the spacer to the detection zone in the acceptor layer containing red rose extract to produce a color change from pink to blue corresponding to the ammonia/ammonium concentration. Under optimum conditions, the proposed method provided good linearity of ammonia in the range concentration of 0-100 mg L

Magnetic Resonance Imaging linear-accelerator (MRI-linac) equipment has recently been introduced to multiple centres in Australia and New Zealand. MRI equipment creates hazards for staff, patients and others in the MR environment; these hazards must be well understood, and risks managed by a system of environmental controls, written procedures and a trained workforce. While MRI-linac hazards are similar to the diagnostic paradigm, the equipment, workforce and environment are sufficiently different that additional safety guidance is warranted. In 2019 the Australasian College of Physical Scientists and Engineers in Medicine (ACPSEM) formed the Magnetic Resonance Imaging Linear-Accelerator Working Group (MRILWG) to support the safe clinical introduction and optimal use of MR-guided radiation therapy treatment units. This Position Paper is intended to provide safety guidance and education for Medical Physicists and others planning for and working with MRI-linac technology. This document summarises MRI-linac hazards and describes particular effects which arise from the combination of strong magnetic fields with an external radiation treatment beam. This document also provides guidance on safety governance and training, and recommends a system of hazard management tailored to the MRI-linac environment, ancillary equipment, and workforce.

The prevalence of diabetes has increased over the past years. Therefore, developing minimally invasive, user-friendly and cost-effective glucose biosensors is necessary especially in low-income and developing countries. Cellulose paper-based analytical devices have attracted the attention of many researchers due to affordability, not requiring trained personnel, and complex equipment. This paper describes a microfluidic paper-based analytical device for the detection of glucose in tear with the naked eye. The paper-based biosensor fabricated by laser CO2, and GOx/HRP enzymatic solution coupled with TMB was utilized as reagents. A sample volume of 10 µl was needed for the biosensor operation and the results were observable within 5 minutes. To evaluate the device performance, color intensity-based and distance-based results were analyzed by ImageJ and Tracker. Distance-based results showed a linear behavior in the range of 0.1–0.6 mM with an R2 = 0.967 and LOD of 0.2 mM. The results could be perceived by the naked eye without any need to further equipment or trained personnel in a relatively short time (3–5 minutes). Moreover, glucose concentration could be obtained non-invasively by tears collected by this µPAD.

Is it really better to print everything, including software models, or is it better to view them on screen? With the ever increasing complexity of software systems, software modeling is integral to software development. Software models facilitate and automate many activities during development, such as code and test case generation. However, a core goal of software modeling is to communicate and collaborate. Software models are presented to team members on many mediums and two of the most common mediums are paper and computer screens. Reading from paper or screen is ostensibly considered to have the same effect on model comprehension. However, the literature on text reading has indicated that the reading experiences can be very different which in turn effects various metrics related to reader performance. This paper reports on an experiment that was conducted to investigate the effect of reading software models on paper in comparison with reading them on a computer screen with respect to cognitive effectiveness. Cognitive effectiveness here refers to the ease by which a model reader can read a model. The experiment used a total of 74 software engineering students as subjects. The experiment results provide strong evidence that displaying diagrams on a screen allows subjects to read them quicker. There is also evidence that indicates that on screen viewing induces fewer reading errors.

Printing technology for electronic devices has received significant attention owing to its fast and massive productivity under ambient conditions. In this study, a facile approach was proposed for manufacturing cellulose paper-based strain sensors with Ni/ multi-walled carbon nanotubes (MWCNT) composites using roll stamping technology. This process enables fabrication of stable sensing structures owing to the formation of stable Ni core enveloping structures in the MWCNT interlacing network. In particular, the rheological properties of the composites revealed shear thinning and thixotropic behaviors, which resulted in fine printing of the sensing electrodes. Furthermore, the shape of the printed patterns, impacted by the pattern morphology, significantly influenced the strain-sensing performance. In particular, the Ni/MWCNT composite-based strain sensor exhibited higher gauge factor of 13.9 with high sensing recovery of 90.4% and stability for 23,500 bending cycles test.

Consistency and clear guidelines on dosimetry are essential for accurate and precise dosimetry, to ensure the best patient outcomes and to allow direct dose comparison across different centres. Magnetic Resonance Imaging Linac (MRI-linac) systems have recently been introduced to Australasian clinics. This report provides recommendations on reference dosimetry measurements for MRI-linacs on behalf of the Australiasian College of Physical Scientists and Engineers in Medicine (ACPSEM) MRI-linac working group. There are two configurations considered for MRI-linacs, perpendicular and parallel, referring to the relative direction of the magnetic field and radiation beam, with different impacts on dose deposition in a medium. These recommendations focus on ion chambers which are most commonly used in the clinic for reference dosimetry. Water phantoms must be MR safe or conditional and practical limitations on phantom set-up must be considered. Solid phantoms are not advised for reference dosimetry. For reference dosimetry, IAEA TRS-398 recommendations cannot be followed completely due to physical differences between conventional linac and MRI-linac systems. Manufacturers’ advice on reference conditions should be followed. Beam quality specification of TPR20,10 is recommended. The configuration of the central axis of the ion chamber relative to the magnetic field and radiation beam impacts the chamber response and must be considered carefully. Recommended corrections to delivered dose are $${k}_{{Q}_{msr}{Q}_{0}}^{{f}_{msr}{f}_{ref}}$$ k Q msr Q 0 f msr f ref , a correction for beam quality and $${k}_{\overrightarrow{B},{Q}_{msr}}^{{f}_{msr}}$$ k B → , Q msr f msr , for the impact of the magnetic field on dosimeter response in the magnetic field. Literature based values for $${k}_{\overrightarrow{B},{Q}_{msr}}^{{f}_{msr}}$$ k B → , Q msr f msr are given. It is important to note that this is a developing field and these recommendations should be used together with a review of current literature.

Purpose The COVID-19 pandemic has been a dramatic trigger that has challenged the intrinsic capacity of older adults and of society. Due to the consequences for the older population worldwide, the Special Interest Group on Comprehensive Geriatric Assessment (CGA) of the European Geriatric Medicine Society (EuGMS) took the initiative of collecting evidence on the usefulness of the CGA-based multidimensional approach to older people during the COVID-19 pandemic. Methods A narrative review of the most relevant articles published between January 2020 and November 2022 that focused on the multidimensional assessment of older adults during the COVID-19 pandemic. Results Current evidence supports the critical role of the multidimensional approach to identify older adults hospitalized with COVID-19 at higher risk of longer hospitalization, functional decline, and short-term mortality. This approach appears to also be pivotal for the adequate stratification and management of the post-COVID condition as well as for the adoption of preventive measures (e.g., vaccinations, healthy lifestyle) among non-infected individuals. Conclusion Collecting information on multiple health domains (e.g., functional, cognitive, nutritional, social status, mobility, comorbidities, and polypharmacy) provides a better understanding of the intrinsic capacities and resilience of older adults affected by SARS-CoV-2 infection. The EuGMS SIG on CGA endorses the adoption of the multidimensional approach to guide the clinical management of older adults during the COVID-19 pandemic.