Search

There has been an increasing interest in recent years in isolating cellulose nanofibers from unbleached cellulose pulps for economic, environmental, and functional reasons. In the current work, cellulose nanofibers isolated from high-lignin unbleached neutral sulfite pulp were compared to those isolated from bleached rice straw pulp in making thin-film ultrafiltration membranes by vacuum filtration on hardened filter paper. The prepared membranes were characterized in terms of their microscopic structure, hydrophilicity, pure water flux, protein fouling, and ability to remove lime nanoparticles and purify papermaking wastewater effluent. Using cellulose nanofibers isolated from unbleached pulp facilitated the formation of a thin-film membrane (with a shorter filtration time for thin-film formation) and resulted in higher water flux than that obtained using nanofibers isolated from bleached fibers, without sacrificing its ability to remove the different pollutants.

Due to the high electric conductivity and large surface area of nanographites, such as graphene and graphite nanoplatlets, these materials have gained a large interest for use in energy storage devices. However, due to the thin flake geometry, the viscosity of aqueous suspensions containing these materials is high even at low solids contents. This together with the use of high viscosity bio-based binders makes it challenging to coat in a roll-to-roll process with sufficient coating thickness. Electrode materials for commercial energy storage devices are often suspended by organic solvents at high solids contents and coated onto metal foils used as current-collectors. Another interesting approach is to coat the electrode onto the separator, to enable large-scale production of flat cell stacks. Here, we demonstrate an alternative, water-based approach that utilize slot-die coating to coat aqueous nanographite suspension with nanocellulose binder onto the paper separator, and onto the current collector as reference, in aqueous metal-free supercapacitors. The results show that the difference in device equivalent series resistance (ESR) due to interfacial resistance between electrode and current collector was much lower than expected and thus similar or lower compared to other studies with a aqueous supercapacitors. This indicates that electrode coated paper separator substrates could be a promising approach and a possible route for manufacturing of low-cost, environmentally friendly and metal-free energy storage devices.

We investigated the properties of the low molecular weight thermo-alkali-stable and mercury ion-tolerant xylanase production from Thermomyces dupontii KKU-CLD-E2-3. The xylanase was purified to homogeneity by ammonium sulfate, Sephadex G–100 and DEAE–cellulose column chromatography which resulted 27.92-fold purification specific activity of 56.19 U/mg protein and a recovery yield of 2.01%. The purified xylanase showed a molecular weight of 25 kDa by SDS–PAGE and the partial peptide sequence showed maximum sequence homology to the endo-1,4-β-xylanase. The optimum temperature and pH for its activity were 80 °C and pH 9.0, respectively. Furthermore, the purified xylanase can maintain more than 75% of the original activity in pH range of 7.0–10.0 after incubation at 4 °C for 24 h, and can still maintain more than 70% of original activity after incubating at 70 °C for 90 min. Our purified xylanase was activated by Cu2+ and Hg2+ up to 277% and 235% of initial activity, respectively but inhibited by Co2+, Ag+ and SDS at a concentration of 5 mM. The Km and Vmax values of beechwood xylan were 3.38 mg/mL and 625 µmol/min/mg, respectively. Furthermore, our xylanase had activity specifically to xylan-containing substrates and hydrolyzed beechwood xylan, and the end products mainly were xylotetraose and xylobiose. The results suggested that our purified xylanase has potential to use for pulp bleaching in the pulp and paper industry.

The fluctuation of domestic wastewater characteristic inhibits the current conventional microbial-based treatment. The bioremediation fungi has received attention and reported to be an effective alternative to treat industrial wastewater. Similar efficient performance is envisaged for domestic wastewater whereby assessed performance of fungi for varying carbon-to-nitrogen ratios in domestic wastewater is crucial. Thus, the performance of pre-grown wild-Serbian Ganoderma lucidum mycelial pellets (GLMPs) was evaluated on four different synthetic domestic wastewaters under different conditions of initial pH (pH 4, 5, and 7) and chemical oxygen demand (COD) to nitrogen (COD/N) ratio of 3.6:1, 7.1:1, 14.2:1, and 17.8:1 (C3.6N1, C7.1N1, C14.2N1, and C17.8N1). The COD/N ratios with a constant concentration of ammonia–nitrogen (NH3–N) were chosen on the basis of the urban domestic wastewater characteristics sampled at the inlet basin of a sewage treatment plant (STP). The parameters of pH, COD, and NH3–N were measured periodically during the experiment. The wild-Serbian GLMPs efficiently removed the pollutants from the synthetic sewage. The COD/N ratio of C17.8N1 wastewater had the best COD and NH3–N removal, as compared to the lower COD/N ratio, and the shortest treatment time was obtained in an acidic environment at pH 4. The highest percentage for COD and NH3–N removal achieved was 96.0% and 93.2%, respectively. The results proved that the mycelium of GLMP has high potential in treating domestic wastewater, particularly at high organic content as a naturally sustainable bioremediation system.

High volumes of formation water comprising of complex mixture of hydrocarbons is generated during crude oil exploration. Owing to ecotoxicological concerns, the discharge of the formation water without remediation of hydrocarbonaceous pollutants is not permitted. Keeping this into mind, we carried out phycoremediation of hydrocarbons in formation water so that it can be safely discharged or re-used. For this, a native algal species was isolated from formation water followed by its morphological and 18S ribosomal RNA based identification confirming the algal isolate to be Chlorella vulgaris BS1 (NCBI GenBank Accession No. MH732950). The algal isolate exhibited high biomass productivity of 1.76 gm L−1 d−1 (specific growth rate: 0.21 d−1, initial inoculum: 1500 mg L−1) along with remediation of 98.63% petroleum hydrocarbons present in formation water within 14 days of incubation indicating an efficient hydrocarbon remediation process. Concomitantly, the hydrocarbon remediation process resulted in reduction of 75% Chemical Oxygen Demand (COD) load and complete removal of sulfate from formation water making it suitable for safe disposal or reuse as oil well injection water respectively. The present process overcomes the bottlenecks of external growth nutrient addition or dilution associated with conventional biological treatment resulting in a practically applicable and cost-effective technology for remediation of oil field formation water.

Biomass-based fly ash and wastewater are undesired products of the pulping industry. Recently, the use of biomass-based fly ash as an adsorbent (i.e., a valued material) for constituents of wastewater effluents was reported. In this work, the settling performance and properties of activated sludge were studied in the presence of fly ash. Upon mixing, fly ash increased the zeta potential of the sludge from −31 mV to −28 mV, which was due to the release of cationic ions from fly ash in the sludge suspension. The sludge settling and its flocculation affinity were improved through the complexation of flocs and released cation ions from fly ash. The relationships between the protein/polysaccharide (PN/PS) ratio and the content of extracellular polymeric substances (EPS) as well as the ratio and the properties of the sludge flocs were determined. A correlation between the total loosely bound-EPS (LB-EPS) content and the effluent suspended solids (ESS) (Pearson’s coefficient, rp = 0.83) was observed. The performance of sludge flocculation and settling were much more closely correlated with LB-EPS than with tightly bound EPS (TB-EPS). Scanning electron microscopy (SEM) analysis of sludge flocs before and after EPS extraction showed that the sludge flocs contained a large number of microorganisms, mainly Bacillus and Cocci. The amount of LB-EPS had an adverse influence on bioflocculation, effluent clarification and sludge settling affinity. The sludge properties had a moderate relationship with the PN/PS ratio of LB-EPS. Also, no correlation could be established between the ratio and the TB-EPS content.

Low permeability oil reservoirs are a widespread petroleum reservoir type all over the world. Therefore, methods to recover these reservoirs efficiently are of importance to guarantee energy supply. Here we report our novel stimulation of indigenous microbes by optimizing the water cut in low permeability reservoirs for green and enhanced oil recovery. We aimed to investigate the characteristics of indigenous bacterial communities with changes in water cut in reservoirs by high-throughput sequencing technology, and reveal the mechanism and characteristics of the crude oil biotreatment under different crude oil-water ratio conditions and the optimum activation time of indigenous functional microbial groups in reservoirs. The indigenous microbial metabolism products were characterized by gas chromatography mass spectrometry. Results showed that Acinetobacter (47.1%) and Pseudomones (19.8%) were the main functional genus of crude oil degradation at the optimal activation time, and can reduce the viscosity of crude oil from 8.33 to 5.75 mPa·s. The dominant bacteria genus for oil recovery after activation of the production fluids was similar to those in the reservoirs with water cut of 60–80%. Furthermore seven mechanism pathways of enhancing oil recovery by the synergistic of functional microbial groups and their metabolites under different water cut conditions in low permeability reservoirs have been established.

Industrial scale-up of microalgal cultures is often a protracted step prone to culture collapse and the occurrence of unwanted contaminants. To solve this problem, a two-stage scale-up process was developed – heterotrophically Chlorella vulgaris cells grown in fermenters (1st stage) were used to directly inoculate an outdoor industrial autotrophic microalgal production unit (2nd stage). A preliminary pilot-scale trial revealed that C. vulgaris cells grown heterotrophically adapted readily to outdoor autotrophic growth conditions (1-m3 photobioreactors) without any measurable difference as compared to conventional autotrophic inocula. Biomass concentration of 174.5 g L−1, the highest value ever reported for this microalga, was achieved in a 5-L fermenter during scale-up using the heterotrophic route. Inocula grown in 0.2- and 5-m3 industrial fermenters with mean productivity of 27.54 ± 5.07 and 31.86 ± 2.87 g L−1 d−1, respectively, were later used to seed several outdoor 100-m3 tubular photobioreactors. Overall, all photobioreactor cultures seeded from the heterotrophic route reached standard protein and chlorophyll contents of 52.18 ± 1.30% of DW and 23.98 ± 1.57 mg g−1 DW, respectively. In addition to providing reproducible, high-quality inocula, this two-stage approach led to a 5-fold and 12-fold decrease in scale-up time and occupancy area used for industrial scale-up, respectively.

Sludge bulking is a major problem that restricts the development of the activated sludge process. The microbial community responsible for sludge bulking varies depending on water quality and operational conditions. This study analysed the microbial community of bulking sludge in oxidation ditch with ultra-low sludge loading and long sludge retention time using high-throughput sequencing. The study found that the relative abundance of bacterial genus Saprospiraceae_norank was the highest in bulking sludge, reaching 13.39–28.83%, followed by Comamonadaceae_unclassified, Ardenticatenia_norank and Tetrasphaera, with the relative abundance of 4.59–11.08%, 0.52–16.60% and 0.17–8.92% respectively. In contrast, the relative abundance of bacteria that easily caused sludge bulking including Microthrix (0.54–2.47%), Trichococcus (0.32–1.71%), Gordonia (0.14–1.28%), and Thiothrix (0.01–0.06%) were relatively low. Saprospiraceae_norank was predominant and induced sludge bulking in oxidation ditch. The relative abundance of fungal genus Trichosporon was the highest in bulking sludge, reaching 16.95–24.98%, while other fungal genera were Saccharomycetales_unclassified (5.59–14.55%), Ascomycota_norank (1.45–13.51%), Galactomyces (5.23–11.23%), and Debaryomyces (7.69–9.42%), whereas Trichosporon was the dominant fungal genus in bulking sludge. This study reported that excessive Saprospiraceae_norank can induce sludge bulking for the first time, which provides important knowledge to control sludge bulking.

Whisky, as a high value product, is often adulterated, with adverse economic effects for both producers and consumers as well as potential public health impacts. Here we report the use of DAPCI-MS to analyse and chemically profile both genuine and counterfeit whisky samples employing a novel ‘direct from the bottle’ methodology with zero sample pre-treatment, zero solvent requirement and almost no sample usage. 25 samples have been analysed from a collection of blended Scotch whisky (n = 15) and known counterfeit whisky products (n = 10). Principal component analysis has been applied to dimensionally reduce the data and discriminate between sample groups. Additional chemometric modelling, a partial least squares regression, has correctly classified samples with 92% success rate. DAPCI-MS shows promise for simple, fast and accurate counterfeit detection with potential for generic aroma profiling and process quality monitoring applications.

To conserve freshwater resources, domestic and industrial wastewater is recycled. Algal systems have emerged as an efficient, low-cost option for treatment (phycoremediation) of nutrient-rich wastewater and environmental protection. However, industrial wastewater may contain growth inhibitory compounds precluding algal use in phycoremediation. Therefore, extremophyte strains, which thrive in hostile environments, are sought-after. Here, we isolated such an alga - a strain of Synechocystis sp. we found to be capable of switching from commensal exploitation of the nitrogen-fixing Trichormus variabilis, for survival in nitrogen-deficient environments, to free-living growth in nitrate abundance. In nitrogen depletion, the cells are tethered to polysaccharide capsules of T. variabilis using nanotubular structures, presumably for nitrate acquisition. The composite culture failed to establish in industrial/domestic waste effluent. However, gradual exposure to increasing wastewater strength over time untethered Synechocystis cells and killed off T. variabilis. This switched the culture to a stress-acclimated monoculture of Synechocystis sp., which rapidly grew and flourished in wastewater, with ammonium and phosphate removal efficiencies of 99.4% and 97.5%, respectively. Therefore, this strain of Synechocystis sp. shows great promise for use in phycoremediation, with potential to rapidly generate biomass that can find use as a green feedstock for valuable bio-products in industrial applications.

Wastewater treatment plants produce hundreds of million tons of sewage sludge every year all over the world. Vermicomposting is well established worldwide and has been successful at processing sewage sludge, which can contribute to alleviate the severe environmental problems caused by its disposal. Here, we utilized 16S and ITS rRNA high-throughput sequencing to characterize bacterial and fungal community composition and structure during the gut- and cast-associated processes (GAP and CAP, respectively) of vermicomposting of sewage sludge. Bacterial and fungal communities of earthworm casts were mainly composed of microbial taxa not found in the sewage sludge; thus most of the bacterial (96%) and fungal (91%) taxa in the sewage sludge were eliminated during vermicomposting, mainly through the GAP. Upon completion of GAP and during CAP, modified microbial communities undergo a succession process leading to more diverse microbiotas than those found in sewage sludge. Consequently, bacterial and fungal community composition changed significantly during vermicomposting. Vermicomposting of sewage resulted in a stable and rich microbial community with potential biostimulant properties that may aid plant growth. Our results support the use of vermicompost derived from sewage sludge for sustainable agricultural practices, if heavy metals or other pollutants are under legislation limits or adequately treated.

To study the influence of diesel fuel blended with polyoxymethylene dimethyl ethers (PODEn), a new alternative fuel with a high oxygen content and large cetane number, on the combustion characteristics, fuel economies, and emission characteristics of heavy-duty diesel engines that meet China VI emission standards, relevant tests were conducted on a supercharged intercooled high-pressure common-rail diesel engine. The PODEn were blended with diesel fuel at three different ratios (volume fractions of 10%, 20%, and 30%). The test results showed that the PODEn could optimize the combustion process of diesel engines that met the China VI emission standards, effectively improve the thermal efficiencies of diesel engines, and reduce the emissions of hydrocarbon (HC), carbon monoxide (CO), and soot. With an increase in the PODEn blending ratio, the peak values of the in-cylinder pressure, average in-cylinder temperature, and instantaneous heat release rate gradually decreased, and each peak progressively moved forward. As the start of combustion gradually moved forward, the combustion duration was shortened by 0.7–2.8°CA, the heat release process became more concentrated, and the effective thermal efficiency was increased by up to 2.57%. The effective fuel consumption gradually increased, yet the equivalent effective fuel consumption gradually decreased, with the largest drop being as high as 4.55%. The nitrogen oxides (NOx) emission increased slightly, and the emissions of HC, CO, and soot gradually decreased. The emissions of CO and soot declined significantly under high-speed and high-load conditions, with the highest reductions reaching 66.2% and 76.3%, respectively.

Industrial development and increased energy requirements have led to high consumption of fossil fuels. Thus, environmental pollution has become a profound problem. Every year, a large amount of agro-industrial, municipal and forest residues are treated as waste, but they can be recovered and used to produce thermal and electrical energy through biological or thermochemical conversion processes. Among the main types of agro-industrial waste, soluble coffee residues represent a significant quantity all over the world. Silver skin and spent coffee grounds (SCG) are the main residues of the coffee industry. The many organic compounds contained in coffee residues suggest that their recovery and use could be very beneficial. Indeed, thanks to their composition, they can be used in the production of biodiesel, as a source of sugar, as a precursor for the creation of active carbon or as a sorbent for the removal of metals. After a careful evaluation of the possible uses of coffee grounds, the aim of this research was to show a broad characterization of coffee waste for energy purposes through physical and chemical analyses that highlight the most significant quality indexes, the interactions between them and the quantification of their importance. Results identify important tools for the qualification and quantification of the effects of coffee waste properties on energy production processes. They show that (SCG) are an excellent raw material as biomass, with excellent values in terms of calorific value and low ash content, allowing the production of 98% coffee pellets that are highly suitable for use in thermal conversion systems. Combustion tests were also carried out in an 80kWth boiler and the resulting emissions without any type of abatement filter were characterized.

Cellulase (mainly endoglucanase, EG) has been used in pulp modification for improving paper quality through environmentally friendly process. But low activity in alkaline pH and high filter paper activity (FPA) were still obstacles for extending the cellulase application in papermaking industry. In the study, an alkali-tolerant EG gene of Bacillus subtilis Y106 was homologous over-expressed for obtaining suitable enzyme used in pulp modification. The engineering strain could produce the crude enzyme with more alkali-tolerant EG and little PFA. Potential of the crude enzyme in modification of different pulps were investigated. It was found that the enzyme could be used for improving drainage and strength properties of pulps from softwood, hardwood and non-wood materials, especially non-wood pulp such as wheat straw pulp. The underlying mechanisms of pulp modification and different effects on various types of pulps by the EG treatment were also discussed by studying the change in fibers characteristics and fiber bonding.

Sugarcane bagasse is a significant renewable energy source for the sugar and bioethanol industries. Bagasse ash is the waste from the combustion process and is mostly disposed of as landfill. Only a small quantity of bagasse ash is utilized as pozzolan in concrete, and a considerable quantity is left unused due to its high carbon and crystallite content. Generally, bagasse ash is rich in silica (SiO2), and it is thus an alternative source for silica extraction. In this paper, a low-energy and low-chemical consumption method is proposed to obtain silica from bagasse ash using alkali extraction and acid precipitation. The physical and chemical properties of the extracted silica are described. A silica yield of 80% and moisture absorption of 73% were achieved. The silica had amorphous phases and was light gray in color owing to the presence of carbon from incomplete combustion. Bagasse silica was used as an extender filler in an expensive photochromic pigment to increase the bulk volume. It was found that a pigment-to-silica mass ratio up to 1:10 could be used for thick-layer painting. However, a ratio of up to 1:3 is recommended for thin-layer screen-printing on fabrics. The bagasse ash silica-pigment blends have very good color fastness when washing; however, frequent aggressive washing should be avoided.

This work presents an alternative method for fabricating Li-ion electrodes in which the use of aluminum/copper current collectors and expensive binders is avoided. Low-cost natural cellulose fibers with a 2-mm length are employed as binder and support for the electrode. The objective of this method is to eliminate the use of heavy and inactive current collector foils as substrates and to replace conventional costly binders with cellulose fibers. Moreover, no harmful solvents, such as N-methylpyrrolidone, are employed for film fabrication. Water-soluble carbons are also utilized to reduce the preparation time and to achieve a better repartition of carbon in the electrode, thus improving the electrochemical performance. Flexible and resistant LiFePO4 (LFP), Li4Ti5O12 (LTO), organic 3,4,9,10-perylenetetracarboxylic dianhydride (PTCDA), and graphite electrodes are obtained with active mass loadings similar to those obtained by the current casting method. The initial discharge capacity of approximately 130 mAh·g−1 at 2 C is obtained for an LFP/LTO paper battery with an approximately 91.6% capacity retention after 1000 cycles. An all-organic prelithiated PTCDA/graphite cell without a transition metal is prepared and electrochemically tested. It is one of the first self-standing batteries that is composed of organic redox active molecules and biodegradable components reported in literature.

The prevention of decrease of quality caused by microbial activity in footwear materials entails the use of biocides. However, these substances may pose a hazard to humans and to the natural environment. The paper presents the results of antimicrobial effect investigation for cowhide leather treated with oregano oil. In these studies oil was applied by spraying onto the finished leather surface and examined to determine its antimicrobial activity by using the Agar Diffusion Plate Test. These results were compared with those where a cowhide leather was treated with oil at the stage of fatliquoring. In addition, the oregano oil toxicity level was assessed and compared with biocides used in the tanning industry. Introducing oregano oil into the leather at the stage of fatliquoring provides a better antimicrobial effect than by spraying, however hygienic finishing of leather can be obtained by introducing oil into the raw material by these both methods. The oregano oil is characterised by the lowest number of hazards and toxicity as compared with commercial biocides. The use of essential oils as natural biocides in the tanning industry seems to be especially important and suitable solution considering the harmful effects of synthetic biocides to humans and the environment.

Proper drying of hands after washing is an integral part of hand hygiene. An experimental study on 30 subjects using multiple comparisons of six hand drying methods including 1) drying on own clothes, 2) drying with one paper towel, 3) drying with two paper towels, 4) drying with a warm air dryer while holding hands stationary for 20 s, 5) drying with a warm air dryer while hand rubbing for 20 s, and 6) drying with a jet air dryer until complete dryness was achieved. It aimed to determine the effectiveness of different hand drying methods for removing bacteria from washed hands, so as to identify the optimum method using minimum resources. Our study demonstrated that the use of jet air dryers is the best method to eliminate bacteria on hands, whereas drying hands on one’s own clothes is the least effective. Drying hands in a stationary position could remove more bacteria than rubbing hands when using a warm air dryer for 20 s, which mimics people’s usual hand-drying practice. No significant difference in bacteria reduction was detected between the use of one or two paper towels for hand drying; therefore, using fewer resources is recommended to maintain environmental sustainability.

Lignocellulosic biomass is an attractive renewable resource to produce biofuel or platform chemicals. Efficient and cost-effective conversion systems of lignocellulosic biomass depend on their appropriate pretreatment processes. Alkali or dilute acid pretreatment of biomass requires a high temperature (> 150 °C) to remove xylan (hemicellulosic sugar) and lignin partially. In this study, peracetic acid was used to pretreat biomass feedstocks, including hardwood and softwood species. It was found that the thermally-assisted dilute acid pretreatment of biomass conducted under the mild temperature of 90 °C up to 5 h resulted in the effective removal of lignin from the biomass with a negligible loss of carbohydrates. This thermally-assisted pretreatment achieved 90% of delignification, and this result was compared with the microwave-assisted pretreatment method. In addition, the crystallinity index (CrI), surface morphology, and chemical structure were significantly changed after the acid pretreatment. The biomass digestibility increased significantly with increased reaction time, by 32% and 23% for hardwood and softwood, respectively. From this study, it is clear that peracetic acid pretreatment is an effective method to enrich glucan content in biomass by delignification.

The requirement of continuous and stringent growth on filtration performance, including longer life span, higher overall efficiency, lower initial pressure drop and more cost effective, has still drove filter media manufactures to research and develop. One of the possible way to achieve these challenges, was to utilize a dual-channel head-box with two sets of pulp conveying system, which can produce filter media with bulky and gradient properties. In this study, three kinds of commercial cellulose were chosen to make two layers filtration media, analyzed the effect of fiber blend on physical properties and filtration performance. By fine-tune the slurry ratio of top layer, we made one single layer and two layers composition filter media, the thickness and air permeability of composition media were higher than single layer media. According to ISO 5011, filtration performance test has been done to compare single layer media with composition media, this composition gradient profiles that provided the life span 37.0% improvement to the terminal pressure drop during dust injecting, and the dust hold capacity improved 34.7%, the main contributor of dust hold capacity was decided by top layer, however, the overall efficiency was depended on wire side layer.

Dragon fruit (Hylocereus spp.), an important tropical fruit belonging to the family Cactaceae, is rich in essential nutrients such as vitamins, minerals, complex carbohydrates, dietary fibres and antioxidants. This study aims to distinguish three dragon fruit species well adapted to Andaman and Nicobar Island through morphological (34 quantitative and 26 qualitative traits), biochemical (5 traits) and molecular (14 ISSR primers) characterization. Morphological characterization revealed that presence of considerable amount of genetic variations among them especially for fruit characters viz., colour of peel and pulp. Cladode characters such as number of spines (3–5), length of areoles (mm) as 1–4, margin ribs of cladode (convex or concave) and its waxiness (weak or strong white waxy or light waxy) could be used for identification of three Hylocereus spp. under present study. Highest co-efficient of variation (%) obtained for pulp weight (88.7), whereas, lowest in distance of anthers belowstigma (3.3). Fruit and pulp weight (g) ranged from 26.5–419.3 and 10.3–258.8 with mean value of 204.8 and 125.3, respectively. Comparatively, high phenol (71.3–161.3) and flavonoid (26.6–508.2) content observed in peels than pulp (32.5–130.0 and 45.0–258.2) of fruit indicating higher antioxidant potential. Highest total carotenoids (µg 100 g−1), β-carotene (µg 100 g−1) and xanthophyll (µg g−1) content obtained in pulp on DGF3 (33.8), DGF4 (55.9) and DGF3 (32.7), whereas, in peel on DGF2 (24.3), DGF4 (18.5) and DGF2 (24.1), respectively. DPPH-based scavenging activity (%) revealed higher scavenging activity of peels (55.6–81.2) than pulp (36.0–75.3) extracts. Comparatively, ABTS-based scavenging activity (%) was found more than DPPH-based one. Sixteen ISSR primers screened, 14 were produced 178 reproducible amplified bands. Number of amplified bands varied from 5 in UBC887 to 19 in UBC811 with an average of 12.71 bands per primer. Range of polymorphic bands and % polymorphism observed were 1–13 and 20.0–92.8, respectively. The polymorphic information content value of ISSR marker ranged from 0.42 (UBC895) to 0.91 (UBC 856). Cluster analysis distinguished three different Hylocereus species on the basis of geographic origin and pulp colour by forming separate groups and two genotypes each showed 52% (DGF1 and DGF3) and 76% (DGF2 and DGF4) genetic similarity. Key traits identified for distinguishing three different Hylocereus species were: Pulp/ peel colour of fruits, number of spines and length of areoles in cladode. Genotypes with high carotenoid and xanthophylls content (DGF4 and DGF2) identified under present study may be of industrial importance for development of nutraceutical products to meet out the vitamin-A deficiency among humans in tropical regions needed future focus.

This study investigated a novel agricultural low-cost bio-waste biochar derived from wood apple fruit shell waste via the pyrolysis method, which is modified by ball milling and utilized to remove toxic phenol and chlorophenols (4-CPh and 2,4-DCPh) from contaminated aqueous media. The ball-milled wood apple fruit shell waste biochar (WAS-BC) sorbent was systematically analyzed by BET, CHN, and FTIR as well as particle size, SEM–EDS, XPS and TGA studies. The sorption equilibrium and kinetic studies exhibit that the sorption capacity was greater than 75% within the first 45 min of agitation at pH 6.0. The uptake capacity of 2,4-DCPh onto WAS-BC was greater than those of 4-CPh and phenol. Equilibrium results were consistent with the Langmuir isotherm model, while the kinetic data were best represented by the Elovich and pseudo-second-order model. The maximum uptake of phenol, 4-CPh, and 2,4-DCPh was 102.71, 172.24, and 226.55 mg/g, respectively, at 30 ± 1 °C. Thus, this study demonstrates that WAS-BC is an efficient, low-cost sorbent that can be used for the elimination of phenol and chlorophenol compounds from polluted wastewater.

The present study was conducted to qualitatively and quantitatively elucidate dynamic changes of ginsenosides in ginseng pulp steamed under different temperatures (100 or 120 °C) for different durations (1–6 h) through UPLC-QTOF-MS/MS and HPLC with the aid of as numerous as 18 authentic standards of ginsenosides. Results show that levels of eight polar ginsenosides (i.e., Rg1, Re, Rb1, Rc, Rb2, Rb3, F1, and Rd) declined but those of 10 less-polar ginsenosides [i.e., Rf, Rg2, 20(S)-Rh1, 20(R)-Rg2, F4, 20(S)-Rg3, 20(R)-Rg3, PPT, Rg5, and 20(R)-Rh2] elevated with increases of both steaming temperature and duration; the optimum steaming conditions for achieving the highest total ginsenosides were 100 °C for 1 h. Particular, 20(R)-Rg3, a representative less-polar ginsenoside with high bioactivity such as potent anti-cancer effect, increased sharply but Re, the most abundant polar ginsenoside in fresh ginseng pulp, decreased dramatically. More importantly, ginsenoside species enhanced from 18 to 42 after steaming, mainly due to transformation of polar into less-polar ginsenosides. Furthermore, four malonyl-ginsenosides were detected in fresh ginseng pulps and ten acetyl-ginsenosides were formed during steaming, demonstrating that demalonylation and acetylation of ginsenosides were the dominant underling mechanisms for transformation of polar into less-polar ginsenosides.

In present study, the effects of carbon sources on compost process and quality were evaluated in the lab-scale sewage sludge (SS) composting. The composting experiments were performed for 32 days in 5 L reactors. The results showed that carbon sources could change the nitrogen conversion and improve the compost quality. Especially, the readily degradable carbon source could promote organic matter degradation, improve nitrogen conversion process and accelerate compost maturation. The addition of glucose and sucrose could increase dissolved organic carbon, CO2 emission, dehydrogenase activity, nitrification and germination index during the SS composting. That's because glucose and sucrose could be quickly used by microbes as energy and carbon source substance to increase activity of microbes and ammonia assimilation. What's more, the NH3 emission was reduced by 26.9% and 32.1% in glucose and sucrose treatments, respectively. Therefore, the addition of readily degradable carbon source could reduce NH3 emission and improve compost maturity in the SS composting.

In the present study, five lignocellulosic biomass namely, corn cobs (Zea mays), rice husks (Oryza sativa), cassava peels (Manihot esculenta), sugar cane bagasse (Saccharum officinarum), and white yam peels (Dioscorea rotundata) of two mesh sizes of 300 and 425 microns and a combination of some and all of the biomass were pretreated using combined hydrothermal and acid-based, combined hydrothermal and alkali-based and hydrothermal only processes. The raw and pretreated biomass were also characterized by Fourier transform infrared spectroscopy (FT-IR), Brunauer–Emmett–Teller (BET), X-Ray diffraction (XRD), and Scanning electron microscopy (SEM) to determine the effects of the various pretreatments on the biomass being studied. The cellulose values of the raw biomass range from 25.8 wt% for cassava peels biomass to 40.0 wt% for sugar cane bagasse. The values of the cellulose content increased slightly with the pretreatment, ranging from 33.2 to 43.8 wt%. The results of the analysis indicate that the hydrothermal and alkaline-based pretreatment shows more severity on the different biomass being studied as seen from the pore characteristics results of corn cobs + rice husks biomass, which also shows that the combination of feedstocks can effectively improve the properties of the biomass in the bioethanol production process. The FTIR analysis also showed that the crystalline cellulose present in all the biomass was converted to the amorphous form after the pretreatment processes. The pore characteristics for mixed corn cobs and rice husks biomass have the highest specific surface area and pore volume of 1837 m2/g and 0.5570 cc/g respectively.

Global warming has become a serious issue nowadays as the trend of CO2 emission is increasing by years. In Malaysia, the electricity and energy sector contributed a significant amount to the nation’s CO2 emission due to fossil fuel use. Many research works have been carried out to mitigate this issue, including carbon capture and utilization (CCUS) technology and biological carbon fixation by microalgae. This study makes a preliminary effort to screen native microalgae species in the Malaysian coal-fired power plant’s surrounding towards carbon fixation ability. Three dominant species, including Nannochloropsis sp., Tetraselmis sp., and Isochrysis sp. were identified and tested in the laboratory under ambient and pure CO2 condition to assess their growth and CO2 fixation ability. The results indicate Isochrysis sp. as the superior carbon fixer against other species. In continuation, the optimization study using Response Surface Methodology (RSM) was carried out to optimize the operating conditions of Isochrysis sp. using a customized lab-scale photobioreactor under simulated flue gas exposure. This species was further acclimatized and tested under actual flue gas generated by the power plant. Isochrysis sp. had shown its capability as a carbon fixer with CO2 fixation rate of 0.35 gCO2/L day under actual coal-fired flue gas exposure after cycles of acclimatization phase. This work is the first to demonstrate indigenous microalgae species' ability as a carbon fixer under Malaysian coal-fired flue gas exposure. Thus, the findings shall be useful in exploring the microalgae potential as a biological agent for carbon emission mitigation from power plants more sustainably.

Odors due to the emission of hydrogen sulfide (H2S) have been a concern in the sewage treatment plants over the last decades. H2S fate and emissions from extended aeration activated sludge (EAAS) system in Muharram Aisha-sewage treatment plant (MA-STP) were studied using TOXCHEM model. Sensitivity analysis at different aeration flowrate, H2S loading rate, wastewater pH, wastewater temperature and wind speed were studied. The predicted data were validated against actual results, where all the data were validated within the limits, and the statistical evaluation of normalized mean square error (NMSE), geometric variance (VG), and correlation coefficient (R) were close to the ideal fit. The results showed that the major processes occurring in the system were degradation and emission. During summer (27 °C) and winter (12 °C), about 25 and 23%, 1 and 2%, 2 and 2%, and 72 and 73% were fated as emitted to air, discharged with effluent, sorbed to sludge, and biodegraded, respectively. At summer and winter, the total emitted concentrations of H2S were 6.403 and 5.614 ppm, respectively. The sensitivity results indicated that aeration flowrate, H2S loading rate and wastewater pH highly influenced the emission and degradation of H2S processes compared to wastewater temperature and wind speed. To conclude, TOXCHEM model successfully predicted the H2S fate and emissions in EAAS system.

The two types of cellulose nanofiber (CNF) surface characteristics were evaluated by oil contact angle under ethanol–water solution at several concentrations as well as in air. Wood pulp-based 2,2,6,6-tetramethylpiperidine-1-oxylradical (TEMPO)-oxidized cellulose nanofiber (TOCNF) sheets and bamboo-derived mechanical counter collision cellulose nanofiber (ACC-CNF) sheets were fabricated by casting followed by drying. The CNF shows underwater superoleophobic mimicking fish skin properties and slippery surface mimicking Nepenthes pitcher. The underwater superoleophobic properties of CNF was evaluated theoretically and experimentally. The theoretical calculation and experimental results of contact angle showed a large deviation. The roughness, zeta potential, and water absorption at different concentrations were key factors that determine the deviation. Antifouling investigation revealed that CNF was a good candidate for antifouling material.

Drying and storage methods are fundamental for maintaining the grain quality until processing. Therefore, the aim of this study was to evaluate the associations of the drying temperature with storage systems and conditions as a strategy for preserving the quality of maize grain postharvest on laboratory and field scales. An increase in temperature accelerated the reduction in grain moisture, but increased the deterioration. The wetting during the storage period reduced the grain quality. Hermetic and aerated storage systems maintained the chemical quality of the grains. The control with healthy and whole corn dried at 80 °C and stored in silos with natural aeration provided a satisfactory quality, equivalent to those of controlled drying and storage under airtight conditions and at low temperatures. Different conditions of drying and storage of corn on the laboratory and field scales were evaluated, which provides an appropriate management of these operations to maintain the grain quality.

Cellulose nanofiber (CNF) with high crystallinity has great mechanical stiffness and strength. However, its length is too short to be used for fibers of environmentally friendly structural composites. This paper presents a fabrication process of cellulose long fiber from CNF suspension by spinning, stretching and drying. Isolation of CNF from the hardwood pulp is done by using (2, 2, 6, 6-tetramethylpiperidine-1-yl) oxidanyl (TEMPO) oxidation. The effect of spinning speed and stretching ratio on mechanical properties of the fabricated fibers are investigated. The modulus of the fabricated fibers increases with the spinning speed as well as the stretching ratio because of the orientation of CNFs. The fabricated long fiber exhibits the maximum tensile modulus of 23.9 GPa with the maximum tensile strength of 383.3 MPa. Moreover, the fabricated long fiber exhibits high strain at break, which indicates high toughness. The results indicate that strong and tough cellulose long fiber can be produced by using ionic crosslinking, controlling spinning speed, stretching and drying.

An amendment to this paper has been published and can be accessed via a link at the top of the paper.

Polyphenols based bioactive compounds from vegetables and fruits are known for impressive antioxidant activity. Ingestion of these antioxidants may promote human health against cardiovascular diseases and cancer. Mango is a popular tropical fruit with special taste, high nutritional value and health-enhancing metabolites. The aim was to investigate the diversity of phytochemicals between two mango cultivars of china at three stages of fruit maturity. We used ESI-QTRAP-MS/MS approach to characterize comprehensively the metabolome of two mango cultivars named Hongguifei (HGF) and Tainong (TN). HPLC was used to quantify selected catechin based phenolic compounds. Moreover, real-time qPCR was used to study the expression profiles of two key genes (ANR and LAR) involved in proanthocyanidin biosynthesis from catechins and derivatives. A total of 651 metabolites were identified, which include at least 257 phenolic compounds. Higher number of metabolites were differentially modulated in peel as compared to pulp. Overall, the relative quantities of amino acids, carbohydrates, organic acids, and other metabolites were increased in the pulp of TN cultivar. While the contents of phenolic compounds were relatively higher in HGF cultivar. Moreover, HPLC based quantification of catechin and derivatives exhibited cultivar specific variations. The ANR and LAR genes exhibited an opposite expression profile in both cultivars. Current study is the first report of numerous metabolites including catechin-based derivatives in mango fruit. These findings open novel possibilities for the use of mango as a source of bioactive compounds.

Made available in DSpace on 2021-06-25T10:15:02Z (GMT). No. of bitstreams: 0 Previous issue date: 2020-12-01 The adoption of dicamba-tolerant soybean varieties has increased the concern and demand for new drift and volatility reduction technologies. Potential spray nozzles and adjuvants should be studied to determine its effects on drift and volatility of dicamba tank-mixtures. The objective of this study was to evaluate physicochemical characteristics of spray solutions containing dicamba; to analyze droplet size effect with air induction nozzles; and to assess dicamba volatilization on soybean plants with a proposed methodology. Treatments included dicamba only and mixtures with herbicides and adjuvants. Dicamba mixed with lecithin + methyl soybean oil + ethoxylated alcohol adjuvant had the greatest efficacy potential among treatments considering tank-mixture pH, surface tension, contact angle and droplet size. The MUG11003 nozzle produced the coarsest droplet size and was better suited for drift management among nozzle types. The proposed volatilization methodology successfully indicated dicamba volatilization in exposed soybean plants and among the evaluated treatments, it showed greater volatilization for dicamba with glyphosate + lecithin + propionic acid adjuvant. Departamento de Ciências da Produção Agrícola UNESP Jaboticabal Campus Departamento de Ciências da Produção Agrícola UNESP Jaboticabal Campus

Residues from the wine industry constitute an abundant feedstock for biodiesel production in wine-producing countries. The use of grapeseed oil, together with bioethanol obtained from distillation of wine surplus or grape skins and stalks and wine lees, as reagents in the transesterification reaction, results in a mixture of fatty acid ethyl esters (FAEE), which is a fully renewable, autochthonous, and waste-derived biofuel. In this work, a blend of FAEE produced from grape seed oil with diesel fuel was selected based on a study of fuel properties, and the optimal blend, with 30% v/v of FAEE, was tested in a Euro 6 engine following the Worldwide harmonized Light-duty Test Cycle (WLTC) and a Real Driving Emissions Cycle (RDE), as required in the new certification procedures. Engine performance and emissions from this blend and a commercial diesel fuel were compared. The FAEE blend showed a significant potential to reduce particle emissions, both in mass and number (from 23% in number to 46.5% in mass for WLTC, and from 56% in number to 61% in mass for RDE), and CO (25.5% for WLTC and 39% for RDE) but penalized NOx (32% higher in WLTC and 26.4% higher in RDE).

Fuels and their components accumulate in soil, and many soil organisms are exposed to this pollution. Compared to intensive research on the effect of conventional fuel on soil, very few studies have been conducted on soil ecotoxicity of biofuels. Considering the limited information available, the present study evaluated the changes caused by the presence of biodiesel and diesel fuel in soil. The reaction of higher plants and soil organisms (microbial communities and invertebrates) was analysed. Conventional diesel oil and two types of biodiesel (commercial and laboratory-made) were introduced into the soil. Two levels of contamination were applied—5 and 15% (w/w per dry matter of soil). The plate method was used to enumerate microorganisms from soil contaminated with biodiesel and diesel fuel. Phytotoxicity tests were conducted by a 3-day bioassay based on the seed germination and root growth of higher plant species (Sorghum saccharatum and Sinapis alba). Fourteen-day ecotoxicity tests on earthworm were performed using Eisenia fetida. Based on the results of the conducted tests it was found out that the organisms reacted to the presence of fuels in a diverse manner. As to the microorganisms, both the growth and reduction of their number were noted. The reaction depended on the group of microorganisms, type of fuel and dose of contamination. The lipolytic and amylolytic microorganisms as well as Pseudomonas fluorescens bacteria were particularly sensitive to the presence of fuels, especially biodiesel. Fuels, even at a high dose, stimulated the growth of fungi. Monocotyledonous sugar sorghum plants were more sensitive to the presence of fuels than dicotyledonous white mustard. There was also a significant negative impact of contamination level on plant growth and development. Biodiesel, to a greater extent than conventional fuel, adversely affected the survival and volume of earthworms.

Cellulose nanofibers were obtained from the Colombian fique (Furcraea bedinghausii) and Acrylic hydrogels (H) and reinforced acrylic hydrogels with fique nanofibres (HRFN) were synthesized, using the solution polymerization method. The extraction was carried out using a combined extraction method (chemical procedures and ultrasound radiation). The raw material (NAT-F), bleached fibers (B-F), hydrolyzed fibers and fibers treated with ultrasound (US-F) were characterized by infrared spectroscopy (FTIR) and thermal stability analysis; also, in order to have a comparison criterion, a commercial microcrystalline cellulose sample (CC) was analyzed, which demonstrated the extraction of fique cellulose. The surface morphology of the NAT-F and the B-F was determined by scanning electron microscopy and the average particle size of the nanofibers was made through transmission electron microscopy. In H y HRFN the strain percent and compression resistance (Rc) were measured. The fique nanofibers showed diameter and length averages of 25.2 ± 6.2 nm and 483.8 ± 283.2 nm respectively. Maximum degradation temperature was 317 °C. HRFN presented higher compression resistance (16.39 ± 4.30 kPa) and this resistance was 2.5 greater than the resistance of H (6.49 ± 2.48 kPa). The results indicate that fique lignocellulosic matrix has potential application for obtaining polymeric type composite materials.

Accumulation of the Municipal Sewage Sludge (MSS) is considered as one of the most harmful renewable ecological and human health problems. MSS is a renewable resource that could be used as a soil organic amendment. This study aims to reduce the Heavy Metals (HMs) from the sludge content and sludge compost. Furthermore, this study is considered the first to assess the mycotoxins content in sludge and sludge compost via a new biological treatment using the fungus Serendipita indica or a mixture of lactic acid bacteria, thus providing safer nutrients for the soil amendment for a longer time and preserving human health. The HMs and mycotoxins were determined. The results exhibited that the biotic remediation of bio-solid waste and sewage sludge compost succeeded; a new bio-treated compost with a very low content of heavy metals and almost mycotoxins-free contents was availed. Also, the results indicated that the Lactobacilli mixture realized the best results in reducing heavy metals contents and mycotoxins. Afterward, S. indica. biotic remediation of bio-solid waste and sewage sludge compost minimized the health risk hazards affecting the human food chain, allowing for the different uses of sludge to be safer for the environment.

Microbial fuel cell (MFC) technology is a simple way to accelerate the treatment of the oily sludge which is a major problem affecting the quality of oil fields and surrounding environment while generating electricity. To investigate the oil removal and the characteristics of changes in the composition of bacteria, sediment microbial fuel cells (SMFCs) supplemented with oily sludge was constructed. The results showed that the degradation efficiency of total petroleum hydrocarbon (TPH) of SMFC treatment was 10.1 times higher than the common anaerobic degradation. In addition, the degradation rate of n-alkanes followed the order of high carbon number > low carbon number > medium carbon number. The odd–even alkane predominance (OEP) increased, indicating that a high contribution of even alkanes whose degradation predominates. The OUT number, Shannon index, AEC index, and Chao1 index of the sludge treated with SMFC (YN2) are greater than those of the original sludge (YN1), showing that the microbial diversity of sludge increased after SMFC treatment. After SMFC treatment the relative abundance of Chloroflexi, Bacteroidia and Pseudomonadales which are essential for the degradation of the organic matter and electricity production increased significantly in YN2. These results will play a crucial role in improving the performance of oily sludge MFC.

Lipids in sewage sludge are considered to be high-class raw materials for biodiesel or other valuable products. We profiled the characteristics and assessed the reutilization potential of lipids from different sludge sources, including sludge from the primary sedimentation tank (PST sludge) and sludge from the secondary sedimentation tank in a conventional activated sludge system (CAS sludge), as well as sludge from ultrashort-sludge retention time (SRT) activated sludge systems with different SRTs (USAS sludge, with SRTs of 0.5, 1.0, 2.0, 3.0 and 4.0 d). The results showed that the lipids in the sludges were mainly composed of cellular lipids, free fatty acids (FFAs), wax and gum. The highest lipid content was found in the PST sludge (156.8 ± 11.9 mg/g, dry basis), followed by the USAS sludges (67.9 ± 11.0–132.2 ± 11.8 mg/g) and the CAS sludge (46.0 ± 16.5 mg/g). Lipid species such as Cer, So, PE, PC, and TG were abundant, comprising over 80% of the cellular lipids in the sludges. With higher lipid contents, the PST sludge and USAS sludge (0.5 d SRT) were suggested to have a higher reutilization potential for use in producing biodiesel. In addition, the CAS sludge was promising for resource reutilization and energy recovery due to the large amount of excess sludge.

The behaviour of ash of fuel affects its thermal efficiency when in use. The ash analyses of bio-coal briquettes developed from lean grade coal and torrefied woody biomass have received limited intensive study. Therefore, the present study aims at analysing the ashes of briquette made from lean grade coal and torrefied woody biomass using blended coal tar pitch and molasses as the binder. Bio-coal briquettes were produced from coal and torrefied biomass in various hybrid ratios. Ashing of various briquettes was done in a muffle furnace at 850 °C for 3 h. Mineral phases of the ash were identified using an X-ray Diffractometer (XRD), while the mineral oxides were obtained using an X-ray Fluorescence Spectrometer. The AFT700 Furnace was used with its AFT700 software to evaluate the ash fusion temperatures of the ashes. The XRD patterns look similar, and quartz was found to be the dominant mineral phase present in the raw coal and bio-coal briquettes. The SiO2 (57–58%), Al2O3 (19–21%), and Fe2O3 (8–9%) were the major oxides observed in the ashes. The final fusion temperatures of the ashes range from 1300–1350 °C. The compositions of the ashes of the bio-coal briquettes are classified as detrital minerals. It was concluded that the addition of torrefied biomass (≤ $$10\%)$$ 10 % ) and blended binder ($$\le $$ ≤ 15%) to coal gave a negligible impact on the ashes of the resultant bio-coal briquettes.

A biochemical system was used for electricity generation from food waste (FW) and spent animal beddings (SAB). The wastes were blended and fermented anaerobically to produce fermentation liquids used as fuels for running a catalytic fuel cell. The fermentation liquids were analyzed for their components. The results show the organic contents i.e. volatile solids of both FW and SAB to be 23.4 and 20.9 g/L while the carbon contents were 6.5 and 6.1 g/L respectively. The media were however very rich in volatile fatty acids (VFAs). When used, the fermentation liquids from FW and SAB generated mean open-circuit voltages of 0.64 and 0.53 V and mean maximum power densities (Pmean) of 1.6 and 1.3 mW/cm2 respectively. The fuel cell showed very high efficiency in the conversion of all VFAs especially butyric acid with the highest been 97% for FW and 96% for SAB.

Sensor data can be wirelessly transmitted from simple, battery-less tags using Radio Frequency Identification (RFID). RFID sensor tags consist of an antenna, a radio frequency integrated circuit chip (RFIC), and at least one sensor. An ideal tag can communicate over a long distance and be seamlessly integrated onto everyday objects. However, miniaturized antenna designs often have lower performance. Here we demonstrate compact, flexible sensor tags with read range comparable to that of conventional rigid tags. We compare fabrication techniques for flexible antennas and demonstrate that screen and stencil printing are both suitable for fabricating antennas; these different techniques are most useful at different points in the design cycle. We characterize two versions of flexible, screen printed folded dipoles and a meandered monopole operating in the 915 MHz band. Finally, we use these antennas to create passive sensor tags and demonstrate over the air communication of sensor data. These tags could be used to form a network of printed, flexible, passive, interactive sensor tags.

Agricultural wastes, such as wheat bran and swine wastewater, were used for bioremediation of oil-contaminated soil. Two optimised strains that could degrade oil efficiently were selected. The result showed that the best ratio of strain A to strain B was 7:3. Swine wastewater could be a replacement for nitrogen source and process water for bioremediation. Next, the Box-Behnken design was used to optimise the culture medium, and the optimal medium was as follows: microbial dosage of 97 mL/kg, wheat bran of 158 g/kg and swine wastewater of 232 mL/kg. Under the optimal medium, the oil degradation rate reached 68.27 ± 0.71% after 40 d. The urease, catalase, and dehydrogenase activities in oil-contaminated soil all increased, and the microbe quantity increased significantly with manual composting. These investigations might lay a foundation for reducing the pollution of agricultural wastes, exploring a late model for bioremediation of oil-contaminated soil.

Two-stage anaerobic digestion of palm oil mill effluent (POME) is a promising method for converting the waste from the largest agricultural industry in Southeast Asia into a clean and sustainable energy. This study investigates the degradation of acid-rich effluent from the dark fermentation stage for the production of biomethane (BioCH4) in a 30-L continuous stirred-tank reactor (CSTR). The continuous methanogenic process was operated with varied HRTs (10 - 1 day) and OLRs (4.6–40.6 gCOD/L.d−1) under thermophilic conditions. Methanothermobacter sp. was the dominant thermophilic archaea that was responsible for the production rate of 4.3 LCH4/LPOME.d−1 and methane yield of 256.77 LCH4kgCOD at HRT of 2 d, which is the lowest HRT reported in the literature. The process was able to digest 85% and 64% of the initial POME’s COD and TSS, respectively. The formation of methane producing granules (MPG) played a pivotal role in sustaining the efficient and productive anaerobic system. We report herein that the anaerobic digestion was not only beneficial in reducing the contaminants in the liquid effluent, but generating BioCH4 gas with a positive net energy gain of 7.6 kJ/gCOD.

The methods of separation of microalgae has a significant impact in the economic aspects of their cultivation. In this study, pine bark was used as a substrate for immobilization of microalgal biomass cultivated in raw municipal sewage. The experiment was conducted in cylindrical photobioreactors (PBRs) with circulation of wastewater. Biomass was cultivated for 42 days. After that time, abundant growth of the biofilm with microalgae on the surface of pine bark as well as improvement of the quality of treated sewage were observed. The efficiency of removal of nutrients from wastewater was 64–81% for total nitrogen and 97–99% for total phosphorus. Moreover, the concentration of suspended solids in sewage was reduced, which resulted in a decrease in turbidity by more than 90%. Colorimetric analysis and Volatile Matter (VM) content in the substrate showed a decrease in the Higher Heating Value (HHV) and concentration of VM due to the proliferation of biofilm.

The industrial wastewater disposal has been growing attention for environmental protection and resource substitution, current decades. Similarly, the durability enhancement of concrete has increased attention by microbial induced CaCO3 precipitation (MICP) process (biocalcification). However, ecofriendly utilization of industrial wastewater in concrete formation is unstudied so far. The present study was carried out to evaluate the effect of industrial wastewater on the formation of cement mortar, compressive strength and water absorption. The biocement mortar strength (y) increased (y = 0.5295×2 + 1.6019×+251.05; R2 = 0.9825) with increasing percentage of organic wastewater (x) (BM0 – BM100) by MICP, where highest strength (280.75 kgf/cm2) was observed on BM100 (100% wastewater), compared to control (252.05 kgf/cm2). The water absorption (y) of biocement mortar decreases (y = −0.0251×2–0.103× + 15.965; R2 = 0.9594) with increment of wastewater (x) (%) (BM0 – BM100), where a minimum-water-absorption (14.42%) observed on BM100, compared to control (15.89%). SEM micrograph and XRD shows the formation of most-distinctive CaCO3 crystallization (aragonite/calcite) (acicular, brick shape, massive and stacked structure) inside biocement mortar (BM100), which fills the pores within cement mortar to form a denser structure, by microbial organic wastewater. Thus, present findings implied a cost-effective of MICP technology to improve the concrete properties along with the mitigation of industrial wastewater pollution, which goes some way towards solving the problem of industrial wastewater pollution.

Phytoremediation is one of the environmental-friendly and cost-effective systems for the treatment of wastewater, including industrial wastewater such as palm oil mill effluent final discharge (POME FD). However, the effects of the wastewater on the phytoremediator plants, in term of growth performance, lignocellulosic composition, and the presence of nutrients and heavy metals in the plants are not yet well studied. In the present work, we demonstrated that POME FD increased the growth of P. purpureum. The height increment of P. purpureum supplied with POME FD (treatment) was 61.72% as compared to those supplied with rain water (control) which was 14.42%. For lignocellulosic composition, the cellulose percentages were 38.77 ± 0.29% (treatment) and 34.16 ± 1.01% (control), and the difference was significant. These results indicated that POME FD could be a source of plant nutrients, which P. purpureum can absorb for growth. It was also found that the heavy metals (Al, As, Cd, Co, Cr, Ni and Pb) inside the plant were below the standard limit of the World Health Organization (WHO). Since POME FD was shown to have no adverse effects on P. purpureum, further research regarding the potential application of P. purpureum following phytoremediation of POME FD such as biofuel production is warranted to evaluate its potential use to fit into the waste-to-wealth agenda.

Respiratory protection is key in infection prevention of airborne diseases, as highlighted by the COVID-19 pandemic for instance. Conventional technologies have several drawbacks (i.e., cross-infection risk, filtration efficiency improvements limited by difficulty in breathing, and no safe reusability), which have yet to be addressed in a single device. Here, we report the development of a filter overcoming the major technical challenges of respiratory protective devices. Large-pore membranes, offering high breathability but low bacteria capture, were functionalized to have a uniform salt layer on the fibers. The salt-functionalized membranes achieved high filtration efficiency as opposed to the bare membrane, with differences of up to 48%, while maintaining high breathability (> 60% increase compared to commercial surgical masks even for the thickest salt filters tested). The salt-functionalized filters quickly killed Gram-positive and Gram-negative bacteria aerosols in vitro, with CFU reductions observed as early as within 5 min, and in vivo by causing structural damage due to salt recrystallization. The salt coatings retained the pathogen inactivation capability at harsh environmental conditions (37 °C and a relative humidity of 70%, 80% and 90%). Combination of these properties in one filter will lead to the production of an effective device, comprehensibly mitigating infection transmission globally.

Mining is an essential human activity, but results in several environmental impacts, notably the contamination of ground and surface water through the presence of toxic substances such as metals and sulfates in mine drainage. Permeable reactive barriers (PRB) have been applied to remediate this environmental impact, but the high costs associated with the maintenance of this system are still a challenge. The main objective of this study was to evaluate the use of kraft pulp mill alkaline residues, known as dregs and grits, as material for PRB, and to determine their capacity for retaining copper and sulfate. The work was carried out in laboratory adsorption kinetics assays, batch assays and column tests. Tests for elemental characterization, point of zero charge, acid neutralization capacity, total porosity, bulk density and moisture of the dregs and grits were conducted. The results showed high retention of Cu due to a chemical precipitation mechanism, notably for dregs (99%) at 5 min in adsorption kinetics. The grits presented similar results after 180 min for the same assay. Sulfate retention was effective at pH below 5, with an efficiency of 79% and 89% for dregs and grits, respectively. Dregs presented the best results for acid drainage remediation, notably with a solid:liquid (S:L) ratio of 1:10.