Search

A new adaptive‐linear‐neuron‐ (ADALINE‐) based dead‐time compensation method is presented for permanent magnet synchronous motor (PMSM) drives. It is proposed to suppress the sixth current harmonics adaptively in the synchronous reference frame due to dead‐time effects. In order to extract the sixth current harmonics, two ADALINE‐based extractors are used without taking into account the electrical lead angle. An improved ADALINE algorithm is used to calculate compensation voltages, taking into account the phase shift of impedance. The proposed method is capable of operating not only at low speed but also at medium and rated speeds in contrast to the traditional compensation method of ADALINE only at low speed. The new method is effective in steady, load dynamic and speed dynamic states with no needs for any extra hardware to detect phase current polarity. The effectiveness of the proposed compensation method is verified on a 780 W PMSM drive through experiments. [ABSTRACT FROM AUTHOR]

The number of neutrons emitted from a nuclear reaction plays a crucial role in various fields, including nuclear theory, nuclear nonproliferation, nuclear energy and nuclear criticality safety. Accurate determination of neutron multiplicities requires the application of several corrections, with dead-time correction and background subtraction being particularly significant. These corrections become more challenging for neutron detectors with time-dependent neutron capture. In this work, we perform a comprehensive study of three existing methods used for dead-time correction and background subtraction in neutron detectors with time-dependent neutron capture. The methods were tested for dead-times in the range from 0 to 1 μs using a Monte Carlo model simulating the dead-time and background effects in the standard neutron multiplicity probability distribution of 252 Cf. The previous methods showed larger than desired uncertainty or systematic trade off. Those uncertainties prompted the development of a novel approach using neural networks trained with data from Monte Carlo simulations. The Neural Network method enabled the correction of neutron multiplicity probabilities more accurately than the other methods with fractional errors smaller than 3% for multiplicities around the peak of 252 Cf. A similar approach using neural networks could be applied to problems where the system being studied can be accurately simulated without having an accurate analytical description available. The neural network method presented in this paper can be easily expanded if multiplicities greater than 10 are expected. [ABSTRACT FROM AUTHOR]

During the modulation process of the VSI motor drive system, the nonlinear errors caused by the dead-time and conduction voltage drop will increase the phase current harmonic distortion and the torque ripple. To solve this problem, a novel dead-time free modulation scheme is proposed in this paper. In the non-zero crossing region of the phase current, the switching tube, whose body diode can provide a continuation path, is set as off-state, the driving signal is only implemented on another switching tube with the same bridge arm, and the errors caused by the conduction voltage drop and switching delay are compensated to the pulse duration. At the same time, to suppress the zero current clamp effect that exists near the zero crossing point of the phase current, another modulation scheme for the phase current crossing zero in advance is proposed, which avoids the complicated determination and calculation of the current polarity near the zero crossing point of the current. Both of the above modulation schemes eliminate the dead-time, and the switching principle is presented. In addition, to suppress the impact of the current ripple and high-frequency noise on the accuracy of the phase current detection, a second-order resonance digital filter without phase shift is introduced. Finally, compared to two deadtime compensation methods, the effectiveness and superiority of the proposed dead-time free modulation scheme are verified by the experimental results. [ABSTRACT FROM AUTHOR]

The recent developments in electric vehicle (EV) necessities the requirement of a human intervention free charging system for safe and reliable operation. Wireless power transfer (WPT) technology shows promising options to automate the charging process with user convenience. However, the operation of the WPT system is designed to operate at a high-frequency (HF) range, which requires proper control and modulation technique to improve the performance of power electronic modules. This paper proposes a dead-time (DT) integrated Pulse Density Modulation (PDM) technique to provide better control with minimal voltage and current ripples at the switches. The proposed technique is investigated using a LCC-LCL compensated WPT system, which predominantly affects the high-frequency voltage and current ripples. The performance analysis is studied at different density conditions to explore the impact of the integrated PDM approach. Moreover, the PDM technique gives better control over the power transfer at different levels of load requirement. The simulation and experimental analysis was performed for a 3.7 kW WPT prototype test system under different modes of operation of the high-frequency power converters. Both the simulated and experimental results demonstrate that the proposed PDM technique effectively enhances the efficiency of the HF inverter while significantly reducing output current ripples, power dissipation and improving the overall WPT system efficiency to 92%, and leading to a reduction in the power loss in the range of 10% to 20%. This leads to improved overall system control and performance. [ABSTRACT FROM AUTHOR]

Designing a controller for a process plant typically modeled as a first or second‐order system with dead time involves an efficient and accurate estimation of its parameters. Since many process plants are characterized as second‐order plus dead time (SOPDT) overdamped or critically damped systems, this study presents a straightforward parameter estimation method using transient response data from a step input at three specific time instants. Two‐time domain performance indices (PIs), TR (= t90t10 for system dead time = 0 and t90−t5t10−t5 for system dead time ≠ 0; t5, t10 and t90 are respectively the times at which the response reaches 5%, 10% and 90% of the steady‐state response) and fr (reciprocal of rise time tr) are proposed in this work. Correlations are established between these PIs and the parameters of the SOPDT system. The first correlation establishes that TR is a function of the damping ratio ξ only and is independent of the undamped natural frequency ωn, which means that the evaluation of TR from the time response data is sufficient to estimate ξ. The second correlation establishes that for a given ξ, fr is a function of ωn. Thus the evaluation of fr from the time response data and an estimate of ξ from the first correlation is sufficient to estimate ωn. The proposed algorithm estimates the parameters of the canonical transfer function of the plant by these correlations from the three specific time instants, as mentioned above, of the step response of the plant. Comparisons with four methods existing in the literature reveal that the method is also effective with higher order systems that may be approximated by SOPDT dynamics, and robust even with measurement noise, making it useful for implementing control strategies, not only in process plants but also in other systems having similar time responses. [ABSTRACT FROM AUTHOR]

The inverter dead time effect is non-negligible for the control performance of sensorless synchronous reluctance motor (SynRM) drives at low speeds. In this paper, a reduced-order observer-based sensorless control method for SynRM drives combined with the adaptive linear neurons (ADALINE)-based dead-time compensation is proposed. The reduced-order observer-based sensorless control method is presented, for which is parameter tuning is easy. On this basis, the dead-time compensation strategy using ADALINE filters is proposed to reduce the voltage harmonics effect on the estimation performance of the reduced-order observer. With ADALINE filters, the sixth current harmonic can be successfully filtered out by compensating the voltage directly or fitting the current to compensate the voltage. In this way, the low-speed estimation performance of the reduced-order observer is improved. The effectiveness of the proposed method is verified on a 3 kW SynRM experimental platform. [ABSTRACT FROM AUTHOR]

This paper presents a comprehensive analysis of the dead-time effects in wireless power transfer systems based on LCC-S topology. In these systems operating at high frequencies, the ratio of dead-time versus the operating period becomes critical, and the dead-time issue can cause certain problems regarding power quality, efficiency, and output voltage ripple. The impact of input quantities such as voltage and switching frequency on the efficiency and output power of the LCC-S-tuned WPT system was also investigated. The optimal combination of these parameters used to achieve the maximum efficiency for a target output power and to set the appropriate value of the dead time were determined by running multiple simulations using the MATLAB R2023b software platform. It was also shown that the output voltage remained unchanged with and without a load and up to 1200 ns of dead-time, which provides a simple implementation of the corresponding mathematical model. In the recommended interval of 600–1500 ns, the influence of the dead-time on the value of the output voltage amplitude is less than 10%. The validity of the proposed method was confirmed through the implementation of the experimental prototype, a 5 kW wireless power transmission system, and the obtained results were in accordance with the simulation results. [ABSTRACT FROM AUTHOR]

This paper proposes a method for compensation of dead-time effects for a fivephase inverter. In the proposed method an additional control subsystem was added to the field-oriented control (FOC) scheme in the coordinate system mapped to the third harmonic. The additional control loop operates in the fixed, orthogonal reference frame (α - β coordinates) without the need for additional Park transformations. The purpose of this method is to minimize the dead-time effects by third harmonic injection in two modes of operation of the FOC control system: with sinusoidal supply and with trapezoidal supply. The effectiveness of the proposed control method was verified experimentally on a laboratory setup with a prototype five-phase interior permanent magnet synchronous machine (IPMSM). All experimental results were presented and discussed in the following paper. [ABSTRACT FROM AUTHOR]

In the case of quantum random number generators based on single-photon arrivals, the physical properties of single-photon detectors, such as time-tagger clocks and dead time, influence the stochastic properties of the generated random numbers. This can lead to unwanted correlations among consecutive samples. We present a method based on extending the insensitive periods after photon detections. This method eliminates the unwanted stochastic effects at the cost of reduced generation speed. We calculate performance measures for our presented method and verify its correctness with computer simulations and measurements conducted on an experimental setup. Our algorithm has low complexity, making it convenient to implement in QRNG schemes, where the benefits of having uncorrelated output intervals exceed the disadvantages of the decreased rate. [ABSTRACT FROM AUTHOR]

An effective dead-time control strategy for the three-phase dual active bridge (3P-DAB) converter of a distribution system is studied to reduce the switching losses of power switches and improve the under-light-load power conversion efficiency. Because of the advantages of a dual-active bridge converter, such as an inherent zero-voltage switching (ZVS) capability without any additional resonant tank and a seamless bi-directional power transition, this is an attractive topology for bi-directional application. The 3P-DAB converter is apt for high-power applications such as aircraft due to an interleaved structure, which can reduce conduction losses. However, the design of the dead time depends on engineering experience and empirical methods. In order to overcome the conventional practicality of the dead-time design method, the effective control of dead time is proposed based on the theoretical analysis. In this paper, the overall explanation of the 3P-DAB converter is shown with operation principles. In addition, the dead-time effect of the 3P-DAB converter is examined and the practical variable dead-time control strategy is studied. Finally, experimental results validate the proposed variable dead-time control strategy using a 25 kW prototype 3P-DAB converter. [ABSTRACT FROM AUTHOR]

This paper investigates the commutation transients of MOSFET and GaN FET devices in motor drive applications during hard-switching and soft-switching commutations at dead time operation. This study compares the switching behaviors of MOSFETs and GaN FETs, focusing on their performance during dead time in inverter legs for voltage source inverters. Experimental tests at various phase current levels reveal distinct switching characteristics and energy dissipation patterns. A validated simulation model estimates the experimental energy exchanged and dissipated during switching transients. The results demonstrate that GaN FETs exhibit lower overall losses at shorter dead times compared to MOSFETs, despite higher reverse conduction voltage drops. The study provides a quantitative framework for selecting optimal dead times to minimize energy losses, enhancing the efficiency of GaN FET-based inverters in low-voltage motor drive applications. Finally, a dead time optimization strategy is proposed and described. [ABSTRACT FROM AUTHOR]

The 2022 Oberammergau Passion Play – a giant applied theatre project with almost 2000 participants, running for 110 performances over five months with a run time of over 5 hours – provides an opportunity to study how community participants use applied theatre's 'dead time': the unstructured, unfacilitated time between onstage appearances. This study argues that in the tight spaces backstage, participants talk, play and engage in acts of care and mentorship, imbuing the dead time with tremendous social value. In fact, much to the initial surprise of the authors, most participants described their interest in the project as being primarily anchored in this dead time, rather than the staged action. These findings leave us with many salient questions for the field of applied theatre, and more research will be needed across varying contexts to better understand how to mitigate the social risks of dead time while invigorating its community-building potential. [ABSTRACT FROM AUTHOR]

In this study, a new modulation method is proposed to reduce the harmonics at the output voltage due to dead time in uninterruptible power supply (UPS) applications. In UPS applications, it is desirable to have low-output voltage harmonics. Dead-time effects in a three-level UPS were investigated for various load conditions. Analysis and simulations related to the proposed method are given and the optimum solution is found by iteration. The validity of the proposed modulation method is tested on two different UPS systems. UPS1 is 20 kVA NPC type, and UPS2 is 160 kVA T type. It is observed that the theoretical and experimental results are in good agreement, and the total harmonic distortion value caused by dead time is significantly reduced at ohmic loads. The proposed method is activated at power factor >0.95 and it improves the output voltage quality as much as the ideal case where the dead time is zero. [ABSTRACT FROM AUTHOR]

Dual active bridge (DAB) is an isolated DC‐DC converter gaining wider attention in power electronics applications. The high frequency (HF) transformer is an integral part of the DAB which is prone to saturation. Silicon carbide (SiC) based DAB are generally preferred for highly efficient power conversions, calling for an extremely low DC resistance of the transformer. This aggravates the DC bias issue significantly. The DC bias current generally flows due to the mismatch in static and transient switching of active devices, leading to eventual saturation of the transformer. This paper proposes an active method to precisely control the dead time of the devices (8–100 ns) without sacrificing the voltage utilization of the converter. This method does not require a sophisticated DC offset current measurement technique. The field programmable gate array (FPGA) based control platform on the gate driver side executes the proposed algorithm. The proposed control is experimentally verified in a 5 kW SiC based converter. The control implementation methodology is discussed with the support of necessary experimental results. [ABSTRACT FROM AUTHOR]

This paper presents the effect of dead time on active power transfer of the dual active bridge (DAB) and a novel mitigation technique for the same. The whole power range is categorized into five zones based on the switching instant link current direction and the modified active power expressions with effect of dead time are derived for each zone. The novel compensation method for dead time improves the performance of any general optimized techniques for DAB with extended phase shift. Firstly, the link current values at different switching instants are estimated using the mathematical expressions obtained using a linear piece-wise method. Secondly, the values are used for compensation logic formulation in the whole power range. The compensation process is applied to two different configurations, open loop (circulating mode) and close loop (voltage control mode). The mid-power zone is compensated using a constant phase shift modification and the low power zone is compensated using a PI controller based phase shift modification. Finally, the effectiveness of the proposed compensation technique is verified through MATLAB Simulink model and 1.2 kW experimental prototype. [ABSTRACT FROM AUTHOR]

Pulsewidth modulation (PWM) strategies, including continuous PWM (CPWM) and discontinuous PWM (DPWM), have been efficiently applied in the three-phase voltage source converters (VSCs). In the three-phase VSCs, dead-time distortion is inevitable. The characteristics of the dead-time distortion of three-phase VSCs with CPWM strategies have been studied extensively, whereas those of DPWM strategies have not been studied in detail. In this article, a comparative analysis of the dead-time distortion of CPWM strategies and DPWM strategies is conducted. Furthermore, the improvement of the PWM strategies to mitigate dead-time distortion is presented. The improved PWM strategies inject the compensation signals to the modulation signals to reconstruct the dead-time voltage error, which can significantly reduce the dead-time distortion of various PWM strategies. Experimental tests are conducted and the experimental results are provided to verify the analysis results of the dead-time distortion of DPWM strategies and the improved PWM strategies. [ABSTRACT FROM AUTHOR]

This brief proposes a driver integrated circuit (IC) for a GaN-based synchronous buck converter to minimized the dead-time loss of GaN devices and improve converter efficiency. The proposed adaptive control achieves minimized dead-time for any loading condition. A driver IC is fabricated in a 0.18 ${\mu }\text{m}$ BCD process to verify the concept. The measurement result achieves only 0.7 ns and 0.8 ns dead-time at the minimum and maximum load condition, respectively. The efficiency improves 2.1% at 2 A full load compared to the fixed dead-time control counterpart. [ABSTRACT FROM AUTHOR]

This letter proposes a proportional-integral-derivative (PID) design method for second-order plus dead time models based on a desired closed-loop transfer function for load disturbance changes. Also, tuning rules for single integrating first-order plus dead time models are provided. Using a two-degree-of-freedom control scheme, the design problem considers load disturbance rejection, robustness to model uncertainties, and setpoint tracking. Three examples are used to assess the performance of the proposed method. Finally, the results are compared to two popular PID control design methodologies, skogestad internal model control or skogestad IMC (SIMC) and improved SIMC (iSIMC). [ABSTRACT FROM AUTHOR]

The main question addressed in this work is how to probe the "effective dead-time" in an NMR instrument, i.e., the time needed to blank the receiver after an rf-pulse excitation to prevent damage to the receiver and to avoid any distortion of the NMR signal being sampled. The strategy is to design a suitable FID-model to fit the single pulse excitation (SPE) and solid echo pulse (SEPS) data (on solid Tricosane) using a Global model-fit analysis technique. The derived dead time is discussed with respect to sampling temperature (25–40 °C) and—in particular—with respect to the number of SEPS data involved in the Global fit analysis by applying the Bayesian Information Criterion (BIC) in combination with more traditional statistical analysis. It is concluded that the "effective dead time" can be determined within a standard error of less than 2.5%. [ABSTRACT FROM AUTHOR]

High current qualities and high efficiencies are always two important characteristics for power converters. However, it is challenging to achieve the two targets simultaneously. In this paper, the dead‐time‐effect elimination pulse‐width‐modulation (PWM) for improving current qualities and the discontinuous PWM (DPWM) for reducing switching losses are combined, proposing a double‐modulation‐wave DPWM. An additional modulation wave is added, whose amplitude is adjusted according to the current polarity. By utilizing the added drive pulses in the current freewheeling stage, the proposed double‐modulation‐wave DPWM successfully reduces the dependence on the current polarities. The overmodulation phenomenon brought by the added modulation wave is analysed, which is proved to be negligible for achieving the maximum modulation index of 1.15. Finally, the effectiveness of the proposed double‐modulation‐wave DPWM is experimentally verified at a switching frequency of 40 kHz. [ABSTRACT FROM AUTHOR]

This article proposes a high-frequency integrated gate driver for gallium nitride (GaN) synchronous buck converter. The proposed adaptive bang-bang dead-time control minimizes dead-time at any load condition. Thus, it mitigates the excessive power loss caused by GaN device reverse conduction in high-frequency applications. The proposed charge sharing bootstrap circuit ensures sufficient gate overdrive voltage with reduced chip area. Fabricated in a TSMC 0.25-μm BCD process, the driver integrated circuit enabled GaN-based buck converter to operate at 10 MHz switching frequency with minimal dead-time to as low as 0.4 ns under light load and heavy load conditions. Compared with fixed dead-time control, the proposed work improves around 5% efficiency under heavy load condition. The fully integrated bootstrap circuit with 100 and 60 pF (HV) capacitor obtained the lower than 0.6 V driving voltage drop with only 45% capacitance and around half of the voltage drop compared with a conventional bootstrap circuit. Besides, the proposed driver successfully tackled the parasitic ringing and dead-time overcharging issues in the GaN converter. [ABSTRACT FROM AUTHOR]

The dead-time between the switches in the upper and the lower bridge of voltage source PWM converters produces input current distortion, called as dead-time distortion. The dead-time distortion can be compensated by trapezoidal voltage. The conventional trapezoidal voltage compensation method (TVCM) only controls the angle of the trapezoidal voltage. By the control of the angle and amplitude of the trapezoidal voltage simultaneously, an improved TVCM is proposed to further reduce the dead-time distortion. The experimental results are provided to verify the analysis results. [ABSTRACT FROM AUTHOR]

Dead time is a common instrumental effect of X-ray detectors, which would alter the behaviour of timing properties of astronomical signals, such as distorting the shape of power density spectra (PDS), affecting the root-mean-square of potential quasi-periodic oscillation signals, etc. We revisit the effects of the dead time of Medium Energy X-ray telescope (ME) onboard Insight - HXMT based on the simulation of electronic read-out mechanism that causes the dead time and the real data. We investigate dead time effects on the pulse profile as well as the quasi–periodic oscillation (QPO) signals. The dead time coefficient suggests a linear correlation with the observed count rate in each phase bin of the pulse profile according to the simulation of periodic signal as well as the real data observed on Swift J0243.6+6124. The Fourier-amplitude-difference (FAD) method could well recover the intrinsic shape of the observed PDS in the case that the PDS is from two identical detectors. We apply this technique on ME, by splitting the nine FPGA modules into two groups. The results indicate that the FAD technique suits the case when two groups of detectors are not largely different; and the recovered PDS of Sco X-1 observed by ME slightly enhances the significance of the previously known QPO signal, meanwhile the root-mean-square of QPO is significantly improved. We provide the FAD correction tool implemented in HXMTDAS for users in the future to better analyse QPO signals. [ABSTRACT FROM AUTHOR]

The purpose of this study was to investigate the impact of voltage drop of a three-phase voltage source inverter on driving brushless motors. This study also proposes an enhanced field-oriented control scheme that accounts for inverter voltage drop, enabling efficient driving at very low motor speeds. Experimental results are provided to verify the theoretical study and the proposed control scheme. [ABSTRACT FROM AUTHOR]

The photon counts (PC) signal of the lidar backscattered signal is affected by the dead time of the transient digitizer. The dead time relies on the photomultiplier (PMT) characteristics and high voltage settings which results in variation of the dead time over time. In this paper, the dead time of the Raman lidar system installed at remote atmospheric monitoring station of CSIR-National Physical Laboratory in Palampur, Himachal Pradesh, India, is estimated and reported. Two different methods proposed by Whiteman et al. and Newsom et al. are used to derive the dead time of the lidar system from June 2016 to June 2019 and the results of both the methods are statistically compared. The results show that the dead time values were found to be increasing from 4 ns to 5.8 ns over the study period. For comparison, one sample t-test and Bland–Altman analysis were used along with the correlation and regression analysis and the results suggest that both the methods were found to be in agreement and there was no statistically significant difference between both the methods. The dead time corrected data was used to obtain glued signal and from that aerosol optical properties have been derived. The optical properties derived from glued signal, dead time corrected and uncorrected signal have been compared and we observed significant difference at the lower altitudes. [ABSTRACT FROM AUTHOR]

As third-generation semiconductors become commercial, SiC semiconductors are gradually becoming more widely used in LLC resonant converters. The efficiency of the LLC resonant converter is improved by employing soft switching. However, when designing LLC resonant converters, semiconductors are usually regarded as ideal devices, and their turn-on and turn-off times are neglected. Furthermore, the method of designing the dead time relies on engineering experience and lacks precise theoretical foundations. In order to overcome the shortcomings of the current empirical method and to improve the generality and practicality of the dead time design method, a novel method for calculating the dead time of full-bridge LLC converters is proposed through theoretical research based on the operating principle of full-bridge LLC converters and the conditions for implementing soft switching. The method takes into account the switching characteristics of semiconductors and the on-state delay time of their body diodes, stray inductance, drive circuits, and errors arising from the first harmonic approximation (FHA) and improves the accuracy of the dead time calculation. It can implement good soft switching with full-bridge LLC converters, reduce switching losses, and improve system efficiency. Finally, the simulation experiment and the 2 kW experimental prototype are built to verify the effectiveness of the proposed method. [ABSTRACT FROM AUTHOR]

A gallium nitride (GaN) field effect transistor can provide superior performance over a Si-mosfet due to its low on-state resistance and low junction capacitances. However, a GaN-based converter exhibits higher dead time loss during reverse conduction. Thus, to improve the efficiency, dead time optimization is required. This article proposes simple models for dead time optimization in a GaN-based buck converter under different load conditions. The proposed models are analytical in nature compared to the conventional models available for Si-based converters. A buck converter prototype is designed using a 100 V GaN device (GS61008P from GaN Systems) and the proposed analytical model-based dead time optimization techniques are validated experimentally. The proposed modeling techniques can be extended for other GaN-based dc–dc converters. [ABSTRACT FROM AUTHOR]

In order to improve the current steady-state control performance of the model predictive control (MPC), a dead-time voltage-vector based MPC method is proposed in this article. First, the effect of the dead-time on MPC is introduced, and the formation process of the dead-time voltage vector existed in MPC is analyzed. Furthermore, the beneficial dead-time voltage vector and nonbeneficial dead-time voltage vector for the current steady-state control performance of MPC is distinguished, and the advantage of the beneficial dead-time voltage vector is analyzed. Then, the MPC method based on dead-time voltage vector is presented, which optimizes the action time of dead-time. Finally, the experimental results prove that the current steady-state control performance of the proposed MPC method is better than the conventional MPC method without increasing the switching frequency. [ABSTRACT FROM AUTHOR]

The validation of equivalent circuit parameters for various power system components remains an important task in power system research. Overhead transmission line parameters available in data sheets may not be correct, particularly for lines having been operated for a long time. In addition, both series and shunt equivalent circuit line parameters can experience deviations as a result of different weather conditions and line loading. Synchrophasor measurements provide the possibility to carry out "passive" monitoring and collect data to compute equivalent circuit line parameters under various power system conditions. Phasor measurement units capturing data from lines operating at 330 kV and above process line currents and voltages (instead of busbar voltages). This provides for continuous monitoring of single-phase automatic reclosing. In this study, synchrophasor measurements are applied to estimate equivalent circuit parameters for the 500 kV Taman – Kubanskaya line as well as to thoroughly analyze a set of conditions on the line reflecting a short circuit followed by a successful line reclosing. All calculations and conclusions are formed on the basis of real data archives containing synchronized vectors of voltages and currents for single-sided switching modes of 500 kV Taman – Kubanskaya line, as well as a short circuit on this line with successful single-phase automatic reclosing. As a result, the capacitive conductivities of the direct and zero sequences, as well as the inductive impedance of the direct sequence were verified. In addition, vector diagrams in the dead time mode of line reclosing were constructed and analyzed in detail, as well as the criteria were considered, which made it possible to perform an a priori assessment of the success of automatic line reclosing according to the synchrophasor measurement data. [ABSTRACT FROM AUTHOR]

Wireless technology is increasingly significant in today's industrial landscape. Standards like WirelessHART, ZigBee, and ISA100.11a are being widely used. However, despite their widespread use, wireless networks may sometimes be susceptible to packet loss or drops, making closed-loop systems vulnerable and resulting in system failure. To prevent such issues, dead-time compensation is necessary. The conventional techniques of predictive PI are commonly used for this purpose. Still, they must perform optimally for wireless networks with dead time, and set-point variations can affect network stability. To address this, a fractional calculus-based predictive PI compensator is proposed in this paper for wireless networks in process industries to improve the performance of these compensators. Industrial processes that involve wireless measurement and control actions in the pressure process model are used to evaluate the proposed compensator. The wireless network's performance is assessed for packet loss, reduced throughput, and increased latency, and the proposed compensator outperforms traditional ones to achieve better set-point characteristics. [ABSTRACT FROM AUTHOR]

In order to effectively avoid the shoot-through issue of the semiconductor device (such as the power metal-oxide-semiconductor field-effect transistor (MOSFET)) adopted in the phase leg of the motor drives, a dead-time zone should be inserted. However, the nonlinearity caused by the dead-time effect will bring about voltage/current distortion, as well as high-order harmonics, which largely degrades the performance of motor drives, especially in low-speed operations with slight loads. In this paper, a dead-time compensation method is proposed to suppress such side effects caused by dead-time zones and improve the performance of motor drives. Compared with other existing methods, the proposed method is mainly focused on the switching characteristics of the power MOSFET, which is directly relative to the compensation time in each pulse-width modulation (PWM) period. Firstly, a detailed derivation process is elaborated to reveal the relationship between compensation time and the switching performance of the MOSFET. Meanwhile, the switching process of the MOSFET is also well analyzed, which summarizes the variations in the switching time of the MOSFET with a varied load current. Then, the multipulse test (MPT) is carried out to obtain accurate values of the switching time with the varied load current in a wide range (0–80 A) and form a 2D lookup table. As a result, the compensation method can easily be realized by combining the lookup table and linear interpolation based on the phase current of the motor dynamically. Finally, the effectiveness of the proposed method is verified based on a 12 V permanent magnet synchronous machine (PMSM) drive system. According to the relative experiment results, it can be clearly observed that the time-domain waveform distortion, high-order harmonics, and total harmonic distortion (THD) value are reduced significantly with the proposed dynamic compensation method. [ABSTRACT FROM AUTHOR]

In this paper, we introduce voltage-controlled oscillators (VCOs) as a new type of nuclear magnetic resonance (NMR) detector, enabling dead time-free detection of NMR signals after an excitation pulse as well as the real-time inductive detection of Rabi oscillations during the pulse. Together with the theory of operation, we present the details of a custom-designed prototype implementation of a VCO-based NMR detector with an operating frequency around 62 MHz. The proof-of-concept measurements obtained with this prototype clearly demonstrate the possibility of performing dead time-free NMR experiments with coherent spin manipulation. Moreover, we also experimentally verified the capability of VCO-based detectors for performing real-time inductive detection of Rabi oscillations during the excitation pulse. [ABSTRACT FROM AUTHOR]

A parameter identification method based on an improved hunter prey algorithm is proposed to address the issues of poor accuracy and speed in traditional permanent magnet synchronous motor parameter identification methods. By using the Fuch infinite folding chaotic strategy to evenly distribute the initial individuals to enrich their diversity and using the golden sine algorithm to optimize the population search path, the algorithm's local development ability and global search ability are improved. The reasons for the dead time effect of the inverter are analyzed, and the input voltage is compensated for through the rotation coordinate method. SIMULINK simulation and physical experiment indicate that the improved algorithm has faster rate of convergence and higher recognition accuracy than the unmodified algorithm, and can effectively identify motor parameters. On this basis, adding dead time compensation effectively eliminates partial harmonics of the phase current and suppresses the occurrence of zero current clamping phenomenon. Compared with the situation without dead time compensation, the identification error of the four parameters has decreased from below 4.23% to below 2.21%. [ABSTRACT FROM AUTHOR]

Voltage source multilevel converters (MLCs) are widely applied in recent years in a wide range of industrial applications. However, time delay inserted in switching signals to prevent short through can cause the dead-time effects, including output waveform distortion and voltage drop. In many kinds of MLCs, the freewheeling paths during dead time can also produce unexpected output voltage levels, which can cross a few consecutive output levels, introducing large dv/dt. Typical examples of those MLCs are 5L-active neutral-point-clamped, 7L-hybrid-clamped, 4L-nested neutral-point-clamped (NNPC) converter, etc. To solve this problem, a generic dead-time elimination (DTE) method is proposed. This method splits the complementary switches and replaces them with controllable switches coupled with uncontrollable diodes, decomposing the phase-leg of the converter into two basic switching cells, thus obviating the need for dead time. To address the zero-current clamping effect inherent to the DTE method, a second-order generalized integrator frequency-locked loop based current detector is also developed. The proposed DTE method is suitable for various MLCs. It cannot only effectively eliminate the unexpected levels, but also significantly reduce the output distortion and regains the output rms value. An application example of 4L-NNPC converter is given. The effectiveness of the proposed method is verified by both simulation and experiment. [ABSTRACT FROM AUTHOR]

Detector dead time losses, caused by both physical components in the detection system and the electronic data acquisition system, are perhaps the most prominent effect in non-ideal detector behavior. Most mathematical modeling methods consider the detector as a single unit with a single dead time parameter, while a true physical detector is often comprised of several serially connected components, each suffering from independent dead time losses. In this study, we develop new formulas for evaluating the dead time losses in a detection system with two serially connected components, each component with a non paralyzing dead time, while assuming that the original count rate has a Poisson distribution. The analytic results obtained are first compared with numeric simulations (showing a very good correspondence) and are then used for numeric investigation of global boundaries of the dead time effect in serially connected systems. [ABSTRACT FROM AUTHOR]

Dead-time is the most important disturbance in a voltage-source inverter's operation. It introduces low-order harmonics at the inverter's output voltage. To compensate for the dead-time effects in three-phase grid-tied inverters, this paper proposes a Linear Quadratic Gaussian (LQG) multivariable control approach. The LQG multivariable control is known as a robust control approach while provides a high band-width for the closed-loop system. Therefore, it promises significant attenuations in the dead-time introduced harmonics. To achieve a high performance, we run the three-phase grid-tied inverter in the current-controlled mode. Based on the nominal multivariable model derived for the three-phase grid-tied inverter in a synchronous reference frame, the LQG controller is composed such that the closed-loop system exhibits robust stability while attenuates disturbances significantly. The dead-time introduced harmonics produce disturbances in the synchronous reference frame with the highest frequencies. This is the reason for considering the dead-time as the most important disturbance in an inverter's operation. For an experimental set-up manufactured for the three-phase grid-tied inverter, we developed a detailed model in MATLAB/Simulink. It is employed for the performance verifications of designed LQG controller. Extensive results are presented for different important scenarios, based on which, the excellent performance of proposed approach is proven. In fact, by employing the proposed approach, the dead-time introduced harmonics are significantly attenuated such that a Total Harmonics Distortions (THD) of about 5% is achieved for the injected currents to grid which meets the IEEE 1547 standard. [ABSTRACT FROM AUTHOR]

Purpose: In continuous manufacturing (CM), the material traceability and process dynamics can be investigated by residence time distribution (RTD). Many of the unit operations used in the pharma industry were characterized by dead time–dominated RTD. Even though feasible and proper feedback control is one of the many advantages of CM, its application is challenging in these cases. This study aims to develop a feedback control, implementing the RTD in a Smith predictor control structure in a continuous powder blender line. Methods: Continuous powder blending was investigated with near-infrared spectroscopy (NIR), and the blending was controlled through a volumetric feeder. A MATLAB GUI was developed to calculate and control the concentration of the API based on the chemometric evaluation of the spectra. The programmed GUI changed the feeding rate based on the proportional integral derivative (PID) and the Smith predictor, which implemented the RTD of the system. The control structures were compared even on a system with amplified dead time. Results: In this work, the control structure of the Smith control was devised by utilizing the RTD of the system. The Smith control was compared to a classic PI control structure on the normal system and on an increased dead time system. The Smith predictor was able to reduce the response time for various disturbances by up to 50%, and the dead time had a lower effect on the control. Conclusions: Implementing the RTD models in the control structure improved the process design and further expanded the wide range of applications of the RTD models. Both control structures were able to reduce the effect of disturbances on the system; however, the Smith predictor presented more reliable and faster control, with a wider space for control tuning. [ABSTRACT FROM AUTHOR]

Copyright of Nuclear Medicine / Nukleární Medicína is the property of Czech Medical Association of JE Purkyne and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Modern applications require the ability to measure time events with high resolution, a full-scale range, and multiple input channels. Time-to-Digital Converters (TDCs) are a popular option to convert time intervals into timestamps. To reduce the time-to-market and Non-Recurring Engineering (NRE) costs, a Field-Programmable Gate Array (FPGA) implementation has been chosen. The high number of requested bits and channels, however, gives rise to routing congestion issues when routed in a parallel manner. In this paper, we will propose and analyze a novel solution, the Belt-Bus (BB), which involves a parallel-to-serial conversion of the timestamp stream coming from the TDC while maintaining chronological order and a sufficient high rate, and flagging the presence of timestamp overflow. Moreover, two new useful features are added. The first is a "Virtual Delay" to compensate for offsets due to cable length and FPGA routing path mismatch. The second is a "Virtual Dead-Time" to filter out unforeseen events. Finally, the BB was tested on a Xilinx 28 nm 7-Series Kintex-7 325T FPGA, achieving an overall data rate of 199.9 Msps with very limited resource usage (i.e., lower than a total of 4.5%), consuming only 480 mW in a 16-channel implementation. [ABSTRACT FROM AUTHOR]

The harmonic problems caused by non‐linear factors of the grid connected inverter (GCI) system are more complicated, including both non‐characteristic harmonics emitted by the dead‐time and the changes in harmonic impedance characteristics. Harmonics interact with the changing impedance, and even cause harmonic amplification and resonance. The harmonic deterioration of the multiple GCIs system is serious. To analyse the mechanism and way of harmonic deterioration in grid‐connected system caused by nonlinear factors, the active impedance models of single inverter and multiple GCIs system including dead‐time effect and digital control delay are established first. In view of this, the influence mechanism of non‐linear factors on system stability is explored. The improved modal analysis method is used to traverse the network series parallel resonance caused by nonlinear factors. The results show that both the dead‐time effect and digital control delay reduce phase margin of the system, resulting in the resonant frequency shift and the resonant peak increase. When the harmonic excitation source interacts with the complex network under the influence of nonlinear factors, it will lead to further deterioration of harmonics. Finally, based on the MATLAB and RT‐LAB hardware‐in‐the‐loop simulation platforms, a multiple GCIs system model is built to verify the correctness of the established active impedance model and harmonic deterioration analysis. [ABSTRACT FROM AUTHOR]

This article proposes a three-stage dead-time adjustment scheme for the leading-leg and lagging-leg switches of phase-shift full-bridge converter (PSFBC) according to the load conditions to enhance the conversion efficiencies at light loads. This article also investigates an iterative rigorous loss calculation for light loads under dead-time adjustment. The proposed iterative calculation can be used to modify the duty ratio of the transition region and estimate the operating currents more accurately; therefore, the losses of a PSFBC at light loads and under the dead-time adjustments can be effectively estimated. A PSFBC prototype with an input voltage of 380 V, an output voltage of 48 V, and a rated output power of 480 W is designed and implemented in this article. Experimental results show that comparing with the PSFBC without the dead-time adjustment and with the conventional dead-time adjustment, the conversion efficiency enhancements of 12.13% and 5.97% can be achieved by the proposed three-stage dead-time adjustment scheme at about 5% load condition, respectively. For a small-scale data center with 100 designed PSFBCs, simulated results indicate that about 3.21 MWh of electricity and 1.03 tons of carbon dioxide emission can be saved and reduced per year, respectively, by the proposed dead-time adjustment scheme. [ABSTRACT FROM AUTHOR]

The adoption of fast-switching silicon carbide (SiC) devices enables power converters to operate at high switching frequencies (e.g., 100 kHz). However, as a limiting factor at high switching frequencies, the dead-time in the conventional pulsewidth modulation (PWM) can cause significant voltage losses, bring serious low-frequency voltage/current harmonics, and reduce the linear modulation region with lower dc-link voltage utilization. Using the dead-time compensation can effectively eliminate the dead-time effect but further reduce the linear modulation region. The dead-time elimination PWM essentially has no dead-time effect. But due to the abandon of drive pulses for generating synchronous rectification, it has a lower converter efficiency, as well as current jumps at zero-crossings. In this article, to overcome the drawbacks of the conventional PWM and the dead-time elimination PWM, a double-modulation-wave PWM for dead-time-effect elimination and synchronous rectification is therefore proposed, where extra drive pulses for generating synchronous rectification are added based on the dead-time elimination PWM. The added drive pulses can also help with mitigating current jumps at zero-crossings. At last, the proposed PWM is experimentally validated and compared with the conventional PWM and the dead-time elimination PWM at 100 kHz on a three-phase converter with SiC mosfets and SiC Schottky diodes, showing the merits of low voltage losses, low output harmonics, high dc-link voltage utilization, large linear modulation region, and high efficiency. [ABSTRACT FROM AUTHOR]

For gallium nitride (GaN) based triangular current mode (TCM) applications, the dead-time has a significant effect on the switching loss. However, previous GaN high electron mobility transistor (HEMT) models focus on the turn-on/off process without fully considering the effect of the dead-time. Hence, this article analyzes the switching transients under the superfluous and insufficient dead-time and evaluates the dead-time loss with an improved GaN HEMT model. The proposed model improves an existing GaN HEMT model by adding the voltage rising/falling time of the gate driver, the dynamic threshold voltage of Schottky-type GaN HEMTs, and an equivalent gate-drain capacitance obtained from the datasheet. Verified by a GaN-based double-pulse test, the proposed model can more accurately calculate the gate-source voltage and the self-commutated reverse conduction voltage. Verified by a GaN-based TCM Buck converter, the proposed model can predict the dead-time loss well and has higher simulation accuracy for the turn-on process induced by the inappropriate dead-time. [ABSTRACT FROM AUTHOR]