Search

• Pulp and paper mill sludge (PPMS) landfill sites have GHG assessment challenges. • GHG fluxes measured by chambers with (F +) and without (F-) a frame were compared. • Flux relationships up to 80 % were shown between F- and F + chambers (the standard) • Correction factors for F- chambers were built to estimate fluxes from F + chambers. • The approach can refine GHG inventories on PPMS landfill sites. Assessments of greenhouse gas (GHG) emissions in managed areas are facing various challenges. A non-flow-through, non-steady-state (NFT-NSS) chamber coupled to a frame permanently inserted into the landfilled substrates is a standard method for quantifying GHG emissions in managed areas, such as pulp and paper mill sludge (PPMS) landfill sites. Frequent measurements are needed to minimize uncertainties on GHG emission factors at the landfill site scale. However, maintaining a frame inserted into the substrates for a long time period is often impossible due to landfilling management operations. Therefore, GHG measurements using NFT-NSS chambers placed directly on substrates' surface could be an interesting option. Our objectives were to determine the relationships between CO 2 , CH 4 , and N 2 O fluxes measured with (F +) and without (F-) a frame inserted in the substrates' surface and to develop correction factors for fluxes measured without a frame. Measurements were made at different PPMS landfill sites in the province of Québec, Canada. Stronger GHG flux relationships were observed at the provincial (across sites) than the specific site scale: the variance in GHG fluxes from F- chambers explained up to 80 % of variance in fluxes from F + chambers. The measured CO 2 , CH 4 , and N 2 O fluxes in F- chambers were on average 53, 78, and 63 % lower, respectively, than those estimated by the models at provincial scale. The correction factors developed with this approach could greatly extend the number of sites where in situ GHG measurements can be done and would help refining GHG inventories at the provincial and national levels. [ABSTRACT FROM AUTHOR]

Development of low-cost, efficient, and stable oxygen evolution electrocatalysts is crucial for the conversion and storage of renewable energy. Therefore, an effective integrated heterostructure catalyst is needed to achieve a lower overpotential during oxygen evolution process. In this paper, cobalt-zinc bimetallic MOF precursors are used as templates to prepare bimetallic cobalt-based selenides with good oxygen evolution catalytic activity and stability on carbon fiber paper. Due to the high specific surface area and porous structure of the coupling structure of nanorods and polyhedra, and the strong electronic coupling between CoSe 2 and ZnSe on nanorods. CoSe 2 -ZnSe/CP exhibits excellent electrocatalytic activity in 1 M KOH solution. It only requires an overpotential of 275 mV to reach the current density of 10 mA cm-2, and the Tafel slope is 68.9 mV dec-1. In addition, after 12 h of continuous operation of CoSe 2 -ZnSe/CP, the activity decay of the catalyst is negligible. This work provides a method for the design of heterogeneous bimetallic selenide integrated oxygen evolution electrocatalysts. [Display omitted] • The CoSe 2 -ZnSe/CP catalyst is obtained by selenization of MOF precursor at high temperature. • The catalyst has unique nanorod-coupled polyhedral morphology and high specific surface area. • The strong electron coupling between CoSe 2 and ZnSe improves the oxygen evolution activity. • CoSe 2 -ZnSe/CP exhibits low overpotential, high exchange current density and fast kinetics. [ABSTRACT FROM AUTHOR]

Enzymes derived from microbial sources have gained increasing popularity in industrial applications over the past decades. Despite the high production cost, alkaline proteases have wide applications in industries such as tanneries, food production, and detergents. In recent years, there has been a shift towards utilizing natural carbon sources for cultivating microorganisms and extracting proteases in order to reduce production costs. This study aimed to investigate the biochemical and kinetic properties of protease enzymes obtained from Aspergillus niger cultivated in a paper waste medium and compare with the enzyme produced in a basal medium. Glucose is a more favorable carbon source compared to cellulose, so paper waste was pretreated with cellulose-degrading bacteria to convert cellulose into smaller carbohydrates. After the growth of A. niger in basal and combinational media, the enzymatic properties were compared between the extracted enzymes by using casein as substrate. The results demonstrated that A. niger could produce protease enzymes in the paper waste medium similar to the basal medium with more than 5-fold cost saving. The specific activity of the enzymes isolated from the basal and paper waste media was calculated to be 184.95 ± 10.56 U ml−1 and 169.88 ± 11.05 U ml−1, respectively. Carbon sources did not affect the optimum pH and temperature of the protease enzyme, which were found to be 8 and 37 °C, respectively. This study provides valuable insights into the production of alkaline protease from A. niger using a combinational medium (paper waste pretreated by cellulose-degrading bacteria), offering a cost-effective approach for industrial applications. [ABSTRACT FROM AUTHOR]

Carbon paper is one of the most widely used gas diffusion layer substrate materials due to its stable performance, relatively low cost, and easy for subsequent processing. Water-soluble phenolic resin, which is more ecologically friendly than alcohol-soluble phenolic resin, was used to prepare carbon paper as the precursor of the carbon matrix. And the effect of different resin solution concentrations on the properties of carbon paper was explored. The results showed that the graphitization, electrical conductivity and mechanical properties of carbon paper increased with the increase of resin solution concentration. When the concentration of resin solution was 20 wt%, the performance of carbon paper was relatively optimal. The graphitization of the carbon paper reached 65.45%, the porosity reached 80.74%, the resistance value at 1 MPa pressure was only 7.61 mΩ cm2, the tensile strength was 1.57 MPa, and the elastic modulus was 1210.98 MPa. [ABSTRACT FROM AUTHOR]

Carbon paper as a macroporous substrate of gas diffusion layer in proton exchange membrane fuel cells directly impacts the output performance of cells. In this study, we present a straightforward strategy to improve the overall performance of carbon paper by mixing short/long (6mm/10 mm) chopped carbon fibers at an optimal concentration of phenolic resin. The results show that incorporating longer carbon fibers can increase the porosity, conductivity, gas flux, and mechanical properties of carbon paper. The membrane electrode assembly achieved a peak power density of 1182.61 mW cm−2 at 60% RH using carbon paper with a long carbon fiber content of 40 wt% and an impregnation concentration of 10 wt%. This outperforms commercially available carbon paper. Based on electrochemical impedance spectroscopy results, it was confirmed that our carbon paper had a lower mass transfer resistance of only 32.17 mΩ cm−2 under conditions of 2 A cm−2 and 60% RH. This was due to its sparser three−dimensional network-like pore structure which was created by mixing different lengths (6mm/10 mm) of carbon fibers. This work provides new insights into preparing high−performance carbon papers. • The nature of carbon paper is regulated by mixing short/long (6mm/10 mm) CFs ratio. • The long carbon fiber contents of 20–40 wt% present better physical properties. • The optimal carbon papers can mitigate mass transfer resistance. • MEA composed of the optimal CP shows a higher power density than commercial CP. [ABSTRACT FROM AUTHOR]

A facile method is proposed in this work to prepare a carbon paper (CP) with outstanding properties by doping boron to catalyze graphitization at lower temperature. Boron was introduced into CP by impregnating carbon fiber preform into a boron/phenolic resin/ethanol solution, and then CP was obtained after the consecutive procedures of hot pressing, carbonization, and graphitization. Morphology, microstructure, composition, and physical properties of the doped and undoped CPs were thoroughly investigated via various techniques to exam the effects of boron concentration and graphitization temperature. Furthermore, the boron doped CP was fabricated into fuel cell gas diffusion layer (GDL) and membrane electrode assembly (MEA) to evaluate its performance through the single cell performance. The findings indicated CP doping with 2 wt% boron could lower the graphitization temperature by at least 200 °C. The B-doped GDL had a higher power density in comparison with the undoped GDLs made in our lab or from the commercial brands. • The innovative preparation method for carbon paper with high conductivity. • The effect of boron concentration and graphitization temperature on carbon paper. • The single cell performance of B-doped gas diffusion layer. [ABSTRACT FROM AUTHOR]

The solar photocatalytic degradation of pulp and paper mill wastewater has been reported by several scientists. However, this is the first time we are reporting for solar photocatalytic hydrogen production from pulp and paper mill wastewater and simultaneous degradation of pollutants. In this work, CuO based photocatalysts and novel square type photocatalytic reactor of 5 L capacity were used. The result shows that the prepared photocatalysts are solar active, efficient in hydrogen recovery and pollutant degradation from the pulp and paper wastewater. The effects of catalyst loading, sacrificial agent, pollutant removal efficiency and stability check were investigated. At 0.25 g/L of CuO/Fe 2 O 3 , 0.2 M of sacrificial agent (Na 2 SO 3 2−) and hydrogen yield of 1000 mL from 1000 mL of wastewater was achieved. The removal efficiency of TSS, TDS, BOD, COD, turbidity and TOC are around 70, 50, 60, 65, 70 and 45% respectively. Reusability study revealed that CuO/Fe 2 O 3 was chemically stable and could be reused successively (five cycles) without significant changes in its photoactivity and intrinsic properties. [Display omitted] • Visible light active CuO mixed with novel metal oxides were employed. • Hydrogen recovery from black liquor, paper mill wastewater were 1000 mL/h/L and 850 mL/h/L. • Efficiency of degradation of pulp & paper wastewater chemicals were around 50–70%. • AcHieved high recovery of hydrogen from pulp & paper wastewater. [ABSTRACT FROM AUTHOR]

The Proton Exchange Membrane Fuel Cell (PEMFC) performances are strongly impacted by the compression of the Gas Diffusion Layer (GDL). Despite its fibrous microstructure, this material is usually considered as a continuous medium and characterized with uniform loading. However, the GDL is subjected to a heterogeneous compression onto rib/channel patterns in the fuel cell assembly. In the present study, a complex behavior of the GDL response is experimentally revealed when the material is loaded with a rib/channel pattern, compared to uniform compression. The tests are simulated by finite element modeling using a classical strain-dependent elastic law, using parameters fitted from uniform compression experiments. It is shown that the numerical results do not reproduce the effect of pattern observed experimentally. Hypotheses to interpret these results involve mechanisms at the fiber microscale including fiber fracture, cross-link breakage and fiber rearrangement, which are exacerbated by larger material deformation caused by the heterogeneous loading. • Unexpected impact of rib/channel patterns on GDL compression. • Experimental investigation of the effect of rib/channel width on GDL deformation. • Numerical study with classical model unable to reproduce experimental results. • Interpretations based on mechanisms at the fiber microscale. [ABSTRACT FROM AUTHOR]

• The PBAT/PLA coated paper shows high methane yield under AD condition. • Plastic film residues remain after the digestion of PBAT/PLA coated paper. • The decrease of hydrophobicity for PBAT/PLA bags is due to the formation of PLA monomers. • The bacterial community shows difference between PBAT/PLA coated paper and bags. • Methanoculleus is enriched on the plastic surface under mesophilic AD. Poly (lactic acid) (PLA) and Poly(butylene adipate-co-terephthalate) (PBAT) are two of biodegradable plastics with the highest production capacities in 2021. Bioplastic waste management can be easily integrated with organic waste management, especially when bioplastics are used as food packaging material, since they are potentially biodegradable. The aim of this study was to assess the biodegradability of biodegradable polymer-coated paper (BPCP) and bioplastic bags made from PBAT/PLA blend during mesophilic and thermophilic anaerobic digestion (AD) and to reveal the changes in the physicochemical properties of the bioplastics. BPCP obtained 155 NmL-CH 4 /g VS and 307.3 NmL-CH 4 /g VS under mesophilic and thermophilic conditions, respectively, but left bioplastic film residues. The bioplastic bags did not exhibit significant biodegradation during the AD processes. 1H NMR results indicated that the ratio of PLA to PBAT decreased significantly after AD of the BPCP film and that PLA monomers were formed from the bioplastic bags, leading to a decrease in the hydrophobicity on the surfaces of the materials. Methanoculleus was found to be enriched on the bioplastic surface after mesophilic AD. From the perspective of coupling bioplastic waste management with the food waste management, the incorporation of BPCP into the AD reactor not only enhances system stability and methane production to a greater extent than biodegradable plastic bags but also raises concerns regarding the residual biofilm when utilizing the digestate for direct land applications. [ABSTRACT FROM AUTHOR]

This paper describes the fabrication and characterization of porous SiC ceramics derived from highly-filled preceramic papers. The SiC ceramics were obtained by spark plasma sintering of stacked preceramic papers at temperatures of 2100 and 2200 °C under pressures of 5–60 MPa for 10 min. The microstructure and phase composition were analyzed by scanning electron microscopy and X-ray diffraction, respectively. Gas permeation tests were performed using hydrogen permeation cell at room temperature. It is revealed that the porosity of sintered SiC can be varied from 9 to 45 % depending on the sintering parameters. The shrinkage of the materials during spark plasma sintering occurs in four stages. The linear shrinkage value of the material increases from 7 to 47 % at 2100 °C and from 20 to 50 % for the samples sintered at 2100 and 2200 °C, respectively. Correlation dependencies between porosity and mechanical properties of the fabricated SiC were established. The obtained porous SiC ceramics exhibit high bending strength of 165 MPa and gas permeation flux of 78 molH 2 /m2/s at the porosity of 36 % that make it suitable for ceramic-based membranes. [ABSTRACT FROM AUTHOR]

Present work covers the treatment of lignin enriched paper industry wastewater (LEPIW) using electrocoagulation (EC) process with stainless steel (SS) electrodes. In this study, EC operation is optimized in term of % chemical oxygen demand (COD) removal and treatment cost (USD/kg COD removed). Single parameter study has been performed to study the effect of process parameters on % COD removal and treatment cost. Central composite design (CCD) of design of expert (DOE) has been used to corelate the input (time, initial COD, solution pH and current) and output parameters (% COD removal and treatment cost). Single parameter study states that maximum % COD removal of 84.4 & 77% is achieved in 40 & 60 min for initial COD:500 &1000 mg/L while 74, 66.7 & 58% can be achieved in 100 min for initial COD of 2000, 3000 & 4000 mg/L, respectively under optimum condition (solution pH:7, current: 1 A). Cost analysis summarizes that treatment cost decreases with increase in initial organic load (2.036, 2.075, 1.554, 1.247 & 1.127 USD/kg COD removed for initial COD of 500, 1000, 2000, 3000 & 4000 mg/L, respectively) at optimum condition. The caloric study states 2.31and 3.25 J/mg can be generated from the sludge and scum produced during EC process. DOE software suggests − 6.66–6.79% & − 16.73–7.95% error between experimental and designed value for % COD removal and treatment cost. [Display omitted] • COD removal range 84.4–58% is noticed for initial COD 500–4000 mg/l. • Treatment time increases from 60 to 100 min for initial COD range of 500–4000 mg/l. • Treatment cost 1.12–2.07 USD/kg COD R is noted for COD range of 500–4000 mg/l. • 2.31 and 3.25 J/mg energy is found from generated sludge and scum respectively. • Model predicts − 6.66–6.79% & − 16.73–7.95% error for COD removal & treatment cost. [ABSTRACT FROM AUTHOR]

The large-scale development of flexible electrode is urgently needed for water electrosplitting. Herein, the common and low-cost filter paper (FP) is utilized as the substrate to adjust the flexible property of the catalytic electrode. Through an electroless plating method, the NiFeP alloys were deposited onto the filter paper, which acted as the flexible and self-supported electrode for hydrogen evolution reaction (HER) and oxygen evolution reaction (OER). The resultant NiFeP@FPs require low overpotentials of 158 mV for HER and 282 mV for OER to deliver a current density of 10 mA cm−2, and exhibit a good stability of 30 h in 1 M KOH. The synergistic effect of Fe–Ni sites regulates electron structure and boosts the catalytic activity. Benefited from good hydrophilicity and interlaced fiber structure of filter paper, electrolyte penetration and electron transfer in the sample are promoted. The assembled two-electrode electrolyzer only requires 1.814 V to achieve 100 mA cm−2 for overall water splitting and shows excellent stability. This work provides a new strategy for the development of flexible and efficient electrodes for water splitting, which advances the development of wearable electronic devices. [Display omitted] • The flexible filter paper-based electrode was successfully synthesized. • The good hydrophilicity and porous structure facilitated electrolyte permeation. • The sample required low overpotentials of 158 mV for HER and 282 mV for OER. • The two-electrode electrolyzer provided 100 mA cm−2 at a low voltage of 1.814 V. [ABSTRACT FROM AUTHOR]

Aerogel composites reinforced by fibers have found extensive applications in the field of thermal insulation and energy conservation. However, the composites are hindered by their high infrared radiation transmittance and weak interface adhesion in practical applications. Herein, we designed and prepared a novel thin composite called 'fiber/whisker/aerogel paper' (SWAP) with a thickness of less than 1 mm. The SWAP integrated SiC nanowhiskers (SiC nw) as opacifiers and ultrafine SiO 2 fibers as reinforcement, fabricated through wet manufacturing and sol-gel process. The 'fiber/aerogel paper' (SAP) and SWAP exhibited low thermal conductivity at room temperature, measuring 0.025 W/(m·K) and 0.033 W/(m·K), respectively. Additionally, they exhibited low densities of 0.195 g/cm3 and 0.225 g/cm3, respectively. Notably, SWAP exhibited excellent high-temperature insulation performance, primarily due to its low infrared transmittance (50% at 3 μm). The incorporation of SiC nw and ultrafine SiO 2 fibers collectively enhanced the interfacial adhesion with the aerogel matrix even amidst rigorous testing (weight loss less than 3%). SWAP also demonstrated flexibility, high thermal stability, hydrophobicity, and flame resistance. Furthermore, a comprehensive investigation into the performance variations and influencing g factors of the material was conducted under different heat treatment conditions. This research provides guidance for the application of such materials under high temperatures. [ABSTRACT FROM AUTHOR]

The ZrO 2 fiber paper exhibits excellent thermal insulation properties, however, its limited mechanical strength and insufficient thermal stability hinder its widespread applications. The composite fiber papers, using mullite fibers possessing a high aspect ratio and exceptional thermal stability combined with ZrO 2 fibers, were fabricated via a vacuum-assisted filtration method. This method involved the successive stacking of composite fibers with alumina sol, using vacuum-induced directed water flow to create a layered structure reminiscent of nacre. The layered structure of the nacre, which demonstrates remarkable strength and hardness, has also served as a source of inspiration for the architectural design of the fiber paper. The tensile strength of pure ZrO 2 fiber paper was significantly enhanced by the addition of 7 wt% mullite fibers, resulting in a remarkable increase to 0.1805 kN/m. The paper exhibited exceptional resistance to bending, maintaining 96 % of its bending strength even after undergoing 100 cycles. The thermal shrinkage of the composite paper, containing 15 wt% mullite fibers, was reduced from 17.75 % observed in pure ZrO 2 fiber paper to a mere 1.32 % after undergoing heat treatment at a temperature of 1300 °C for 2 h. The composite paper, measuring 5 mm in thickness and consisting of 7 wt% compositions, displayed exceptional thermal insulation properties when exposed to a hot side temperature of 1370 °C. It effectively insulated temperatures up to approximately 1000 °C. [ABSTRACT FROM AUTHOR]

Black liquor (BL) bioconversion into valuable by-products is essential to develop a bioeconomy strategy; however, its furfural content hinders microbial fermentation activities. Hence, this study utilizes paper mill sludge (PMS) to provide extracellular enzymes, furfural-degrading microbial consortia, and electron donor required for promoting the BL hydrogenesis potential. Three up-flow anaerobic sequential batch reactors (UASBRs) are fed with PMS (UASBR1), BL (UASBR2), and PMS + BL (UASBR3) and operated in parallel at 15 min fill, 72 h reaction, and 4 h settling. The UASBR3 achieves the maximum volumetric H 2 of 1.483 ± 0.088 L/L/d and H 2 yield of 2.06 ± 0.12 mol/mol glucose, which drops by 88% in UASBR2 and 24% in UASBR1. The insufficient H 2 productivity values in UASBR2 could be due to a lack of nutrients availability (C:N = 440:1 and C:P = 19:1), higher furfural concentration (2116 ± 422 mg/L), and involvement of the butyrate fermentation pathway. The synergetic effect between PMS and BL overcomes these limitations and enriches the fermentation medium with Proteobacteria phyla (22.8%) and Acinetobacter sp. degrading furfural (6.1%). The microbial community at the phylum level (e.g., Proteobacteria , Firmicutes , and Actinobacteria) in UASBR3 maximizes the migration of electrons (e−eq = 9.34 ± 0.54%) towards efficient H 2 formation. [Display omitted] • Paper mill sludge (PMS) mitigated inhibitory effect of furfural in black liquor (BL). • PMS improved H 2 yield from the BL by 8.3-folds and accounted for 2.1 mol/mol glucose. • e– eq transferred to H 2 was 9.3% in the PMS:BL, 7.4% in PMS, and 1.27% in BL. • Acinetobacter degrading furfural (6.1%) was abundant with PMS addition. • Bacilli (8.9%) and Clostridia (5.4%) was dominant in the hydrogenesis of PMS:BL. [ABSTRACT FROM AUTHOR]

A noble-metal-free bifunctional electrocatalyst with outstanding activity and stability is of great importance for the development of rechargeable zinc-air batteries (ZABs). Herein, we employed a facile strategy to fabricate nitrogen-doped NiCo 2 O 4 nanostructures on carbon paper as a binder-free air cathode for rechargeable ZABs. An optimized process of nitrogen plasma treatment has enhanced the electrical conductivity of the metal oxide and induced abundant active sites into the crystal structures, resulting in enhanced electrocatalytic activities toward oxygen evolution reaction (OER) and oxygen reduction reaction (ORR). Notably, mild plasma treatment leads to efficient N doping while the morphology and specific surface area of the catalyst both remain unchanged. The air cathode with NiCo 2 O 4 doped with nitrogen in 2 min plasma treatment and integrated into a zinc-air battery with liquid electrolyte provided a small charge-discharge voltage gap and distinguished cycling stability superior to the air cathode with noble-metal catalyst counterparts. Furthermore, the solid-state zinc-air battery with this material displays excellent stability with just a small increase of the charge-discharge voltage gap over 20 h of operation. This work illustrates the promising potential of plasma treatment in the fabrication of high-performance catalysts. • N-doped NiCo 2 O 4 was prepared by hydrothermal method and N 2 plasma treatment. • Mild plasma treatment leads to efficient N doping in NiCo 2 O 4. • NiCo 2 O 4 with N 2 plasma treatment of 2 min exhibits excellent OER/ORR performances. • N–NiCo 2 O 4 -2 min worked as a binder-free air cathode in Zn-air batteries. [ABSTRACT FROM AUTHOR]

The importance of shared decision making (SDM) for informed consent has been emphasised in the updated regulatory guidelines. Errors of completion, legibility and omission have been associated with paper-based consent forms. We introduced a digital consent process and compared it against a paper-based process for quality and patient reported involvement in shared decision making. 223 patients were included in this multi-site, single centre study. Patient consent documentation was by either a paper consent form or the Concentric digital consent platform. Consent forms were assessed for errors of legibility, completion and accuracy of content. Core risks for 20 orthopaedic operations were pre-defined by a Delphi round of experts and forms analysed for omission of these risks. SDM was determined via the 'collaboRATE Top Score', a validated measure for gold-standard SDM. 72% (n = 78/109) of paper consent forms contained ≥1 error compared to 0% (n = 0/114) of digital forms (P < 0.0001). Core risks were unintentionally omitted in 63% (n = 68/109) of paper-forms compared to less than 2% (n = 2/114) of digital consent forms (P < 0.0001). 72% (n = 82/114) of patients giving consent digitally reported gold-standard SDM compared to 28% (n = 31/109) with paper consent (P < 0.001). Implementation of a digital consent process has been shown to reduce both error rate and the omission of core risks on consent forms whilst increasing the quality of SDM. This novel finding suggests that using digital consent can improve both the quality of informed consent and the patient experience of SDM. • The paper consent process is associated with errors and omissions of core risks. • A digital consent process improved error rate and omission rate of core risks. • Patients reported a higher level of shared decision making with a digital process. • Documentation of consent can be reliably standardised with an electronic record. [ABSTRACT FROM AUTHOR]

Ni-doped WC/Mo 2 C composites for hydrogen evolution reaction (HER) were synthesized in situ grown on carbon fiber paper (CFP) by molten salt method in argon at 1000 °C for 6 h, named as Ni-xWC-y/2Mo 2 C@CFP. The effects of different W/Mo molar ratios (3:1, 2:1, 1:1, 1:2, 1:3) on the phase composition, microstructures, and HER performances were investigated. The results showed that the W/Mo molar ratio had a synergistic effect in HER of Ni-doped WC/Mo 2 C composites, and as W/Mo molar ratio at 1:1, the composite presented the best electrocatalytic activity. Meanwhile, its surface appeared to have a wrinkle-like structure, and the biphasic heterostructure emerged at the intersection of the dual-phase WC and Mo 2 C lattices. The introduction of a biphasic heterostructure could promote charge transfer and improve HER efficiency. Predictably, the electrocatalysts with the optimal W/Mo molar ratio 1:1 exhibited the best hydrogen evolution performance, needed only 43.7 mV overpotential to reach 10 mA cm−2 current density with a Tafel slope at 21.3 mV dec−1. In this work, the high-efficiency electrocatalysts of Ni-doped 1WC-1/2Mo 2 C@CFP have been prepared, which provides an insight into theoretical research of composite carbon-based electrocatalysts. [ABSTRACT FROM AUTHOR]

To solve the durability problem caused by carbon corrosion in the porous carbon paper gas diffusion layer (GDL) of proton exchange membrane fuel cell (PEMFC), a Cr 7 C 3 ceramic coating on porous carbon paper by molten salt method was prepared. The obtained Cr 7 C 3 coating is dense and shows good adherent with the carbon paper. Based on the corrosion resistance testes, it is concluded that the Cr 7 C 3 coated carbon paper can keep high chemical stability in the long-time acid immersion accelerated corrosion tests and simulated cathodic proton exchange membrane fuel cells environment. The carbon paper with Cr 7 C 3 coating shows a small current density with a value of about 1.1 × 10−5 A cm−2 in the potentiostatic polarization test under 1 M H 2 SO 4 + 2 ppm HF at 70 °C and1.4 V SCE for 72 h. Meanwhile, the resistivity of carbon paper with Cr 7 C 3 coating prepared is 30% lower than that of pure carbon paper, and the conductivity is 1.5 times that of pure carbon paper. [ABSTRACT FROM AUTHOR]

This research investigated the hydrogen production and energy conversion from automobile shredder residues (ASRs) and paper mill sludge (PMS) co-gasified in a full-scale fluidized bed gasification plant. The results obtained from full-scale tests provided important information on the feasible assessment of ASRs-to-energy and the selection of alternative technologies for ASRs. Based on the analysis results of produced gas composition, H 2 , CO, and CH 4 composition produced from paper-mill sludge gasified were 4.17%–6.01%, 3.08%–4.32%, 1.71%–2.4%, respectively. Another C 2 gas composition ranged from 2.9% to 3.59%. The heating value of produced gas ranged between 1.64 MJ/Nm3 and 2.18 MJ/Nm3. In the case of 10% ASR addition, the heating value of produced gas was slightly increased to 1.84 MJ/Nm3-2.34 MJ/Nm3. The dioxin emission concentration of flue gas was approximately 0.064 ng I-TEQ/Nm3. It can comply with Taiwan regulation thresholds. The dioxin leaching concentrations of residues derived from gasification were also in compliance with regulation limits by the TCLP test. Meanwhile, in the case of 10% ASRs addition, the dioxin equivalence concentration of gasified residue was nearly 0.002 ng I-TEQ/Nm3. It was far below the current regulation standard limit. In summary, the results of this research have proved the performance of ASRs-to-energy by co-gasified with paper mill sludge using a full-scale gasification plant. The results obtained from this research also provided the information for selecting ASRs alternative technologies and operating full-scale gasifiers in the future. [Display omitted] • This study has confirmed the feasibility of co-gasification of calcium-rich PMS and chlorine-rich ASRs. • Adding 5%–15% of ASRs can maintain the regular operation of the full-scale commercial gasifier. • The synthesis gas has a composition of 4.91 vol% H 2 and 2.06 vol% CO, with a LHV of 1.93 MJ/Nm3. • The HCl emission could comply with regulation thresholds in co-gasification. • Dioxin reformation reduced significantly in co-gasification of PMS and ASRs. [ABSTRACT FROM AUTHOR]