Search

Development of paper-based microfluidic devices that perform colorimetric measurements requires quantitative image analysis. Because the design geometries of paper-based microfluidic devices are not standardized, conventional methods for performing batch measurements of regularly spaced areas of signal intensity, such as those for well plates, cannot be used to quantify signal from most of these devices. To streamline the device development process, we have developed an open-source program called ColorScan that can automatically recognize and measure signal-containing zones from images of devices, regardless of output zone geometry or spatial arrangement. This program, which measures color intensity with the same accuracy as standard manual approaches, can rapidly process scanned device images, simultaneously measure identified output zones, and effectively manage measurement results to eliminate requirements for time-consuming and user-dependent image processing procedures.

Nowadays, due to environmental pollution and natural energy consumption caused by waste paper, many researches are being conducted on the reuse of printed-paper. To recycle the paper, de-inking has to be performed. In this article, in order to reduce the use of the commonly used de-inking chemicals, the effect of an atmospheric pressure helium plasma treatment on the de-inking enhancement of printed-paper is studied. Through colorimeter and UV-visible spectrometer measurements the plasma treatment is shown to speed up the de-inking. While SEM observations and FTIR measurements suggest that the paper quality is retained upon plasma treatment, the increase of surface hydrophilicity measured by water contact angle measurements, compared to non-treated paper, is believed to enhance the fiber swelling of the paper and lead to a faster ink removal.

The amount of Paper Board Mill Effluent Treatment Plant Sludge (PBM-ETPS) dumped from paper mills are huge and its conversion into hydrochar for the purpose of energy has broad prospects. This study investigated the optimum conditions for the production of PBM-ETPS derived hydrochar (PBM-ETPSH) through Reponse Surface Methodology (RSM) for more surface area and pore volume with minimal hydrogen to carbon (H/C) and oxygen to carbon (O/C) ratios. The PBM-ETPSH had higher heating value (HHV) of 18.39 MJ kg−1 with fixed carbon percentage of 15.6. Our results showed a reduction in H/C (35.05%) and O/C (43.7%) ratios confirming the coalification of optimized PBM-ETPSH. Thermogravimetric investigations of blending PBM-ETPSH with coal in 1:1 ratio increased its HHV to 22.25 MJ kg−1 making it suitable as an energy alternative for paper mills.

Paper has been pursued as an interesting substrate material for sensors in applications such as microfluidics, bio-sensing of analytes and printed microelectronics. It offers advantages of being inexpensive, lightweight, environmentally friendly and easy to use. However, currently available paper-based mechanical sensors suffer from inadequate range and accuracy. Here, using the principle of supercapacitive sensing, we fabricate force sensors from paper with ultra-high sensitivity and unprecedented configurability. The high sensitivity comes from the sensitive dependence of a supercapacitor’s response on the contact area between a deformable electrolyte and a pair of electrodes. As a key component, we develop highly deformable electrolytes by coating ionic gel on paper substrates which can be cut and shaped into complex three-dimensional geometries. Paper dissolves in the ionic gel after determining the shape of the electrolytes, leaving behind transparent electrolytes with micro-structured fissures responsible for their high deformability. Exploiting this simple paper-based fabrication process, we construct diverse sensors of different configurations that can measure not just force but also its normal and shear components. The new sensors have range and sensitivity several orders of magnitude higher than traditional MEMS capacitive sensors, in spite of their being easily fabricated from paper with no cleanroom facilities.

Low energy surface coatings have found wide range of applications for generating hydrophobic and superhydrophobic surfaces. Most of the studies have been related to use of a single coating material over a single substrate or using a single technique. The degree of hydrophobicity is highly dependent on fabrication processes as well as materials being coated and as such warrants a high-level study using experimental optimization leading to the evaluation of the parametric behavior of coatings and their application techniques. Also, a single platform or system which can predict the required set of parameters for generating hydrophobic surface of required nature for given substrate is of requirement. This work applies the powerful machine learning algorithms (Levenberg Marquardt using Gauss Newton and Gradient methods) to evaluate the various processes affecting the anti-wetting behavior of coated printable paper substrates with the capability to predict the most optimized method of coating and materials that may lead to a desirable surface contact angle. The major application techniques used for this study pertain to dip coating, spray coating, spin coating and inkjet printing and silane and sol–gel base coating materials.

Paper-based microfluidic devices have many applications in biomedical and environmental analysis. However, the process of prototyping device designs can be tedious, error-prone, and time-consuming. Here, we present a cross-platform, open-source software tool—AutoPAD—developed to quickly create and modify device designs and provide a free alternative to commercial design software. The capabilities that we designed to be inherent to AutoPAD (e.g., automatic zone alignment and design refactoring) highlight its potential use in nearly any paper-based microfluidic device application and for creating nearly any desired design, which we demonstrate through the recreation of numerous device designs from the literature.

We present a simple all-in-one paper-based sensor for E. coli detection using a composite ink made of a fluorogenic DNAzyme probe for bacterial recognition and signal generation, lysozyme that lyses whole bacterial cells, and pullulan/trehalose sugars that stabilize printed bioactive molecules. The paper sensor is capable of producing a fluorescence signal as a readout within 5 minutes upon contacting E. coli, can achieve a limit of detection of 100 cells/mL, in a variety of sample matrixes, without sample enrichment, and remains stable for at least 6 months when stored at ambient temperature. Therefore, this simple paper sensor provides rapid bacterial testing on site, and can be shipped and stored under ambient conditions to benefit users living in resource-limited regions.

Paper-based micro analytical devices offer significant advantages compared to the conventional microfluidic chips including cost-effectiveness, ease of fabrication, and ease of use while preserving critical features including strong capillary action and biological compatibility. In this work, we demonstrate an inexpensive, rapid method for high-throughput fabrication of paper-based microfluidics by patterning hydrophobic barriers using a desktop pen plotter integrated with a custom-made, low-cost paper feeder. We tested various types of commercial permanent markers and compared their water-resistant capabilities for creating hydrophobic barriers. Additionally, we studied the performance of markers with different types of paper, plotting speeds, and pattern dimensions. To verify the effectiveness of the presented fabrication method, colorimetric analysis was performed on the results of a glucose assay.

3D printed and paper-based microfluidics are promising formats for applications that require portable miniaturized fluid handling such as point-of-care testing. These two formats deployed in isolation, however, have inherent limitations that hamper their capabilities and versatility. Here, we present the convergence of 3D printed and paper formats into hybrid devices that overcome many of these limitations, while capitalizing on their respective strengths. Hybrid channels were fabricated with no specialized equipment except a commercial 3D printer. Finger-operated reservoirs and valves capable of fully-reversible dispensation and actuation were designed for intuitive operation without equipment or training. Components were then integrated into a versatile multicomponent device capable of dynamic fluid pathing. These results are an early demonstration of how 3D printed and paper microfluidics can be hybridized into versatile lab-on-chip devices.

Triboelectric nanogenerators (TENGs) offer an emerging market of self-sufficient power sources, converting the mechanical energy of the environment to electricity. Recently reported high power densities for the TENGs provide new applications opportunities, such as self-powered sensors. Here in this research, a flexible graphene oxide (GO) paper was fabricated through a straightforward method and utilized as the electrode of TENGs. Outstanding power density as high as 1.3 W.m−2, an open-circuit voltage up to 870 V, and a current density of 1.4 µA.cm−2 has been extracted in vertical contact-separation mode. The all-flexible TENG has been employed as a self-powered humidity sensor to investigate the effect of raising humidity on the output voltage and current by applying mechanical agitation in two forms of using a tapping device and finger tapping. Due to the presence of superficial functional groups on the GO paper, water molecules are inclined to be adsorbed, resulting in a considerable reduction in both generated voltage (from 144 V to 14 V) and current (from 23 µA to 3.7 µA) within the range of relative humidity of 20% to 99%. These results provide a promising applicability of the first suggested sensitive self-powered GO TENG humidity sensor in portable/wearable electronics.

We present a prototype for conducting rapid, inexpensive and point-of-care-compatible nucleic acid amplification tests (NAATs) for tuberculosis (TB). The fluorescent isothermal paper-and-plastic NAAT (FLIPP-NAAT) uses paper-based loop mediated isothermal amplification (LAMP) for DNA detection. The cost of materials required to build a 12-test-zone device is $0.88 and the cost of reagents per reaction is $0.43. An inexpensive imaging platform enables filter-free fluorescence detection of amplified DNA using a cell-phone camera. FLIPP-NAAT can be operated by an untrained user and only requires a regular laboratory incubator as ancillary equipment. All reagents can be dry-stored in the device, facilitating storage and transportation without cold chains. The device design is modular and the assay demonstrated high specificity to Mycobacterium tuberculosis (Mtb), analytical sensitivity of the order of 10 copies of Mtb gDNA, and tolerance to complex samples. The clinical sensitivity and specificity of sputum-based FLIPP NAAT tests were 100% (zero false negatives) and 68.75% (five false positives), respectively (N = 30), using Xpert MTB/RIF assay as the reference standard. FLIPP-NAAT has the potential to provide affordable and accessible molecular diagnostics for TB in low- and middle-income countries, when used in conjunction with an appropriate sample preparation technique. Although demonstrated for the detection of TB, FLIPP-NAAT is a platform technology for amplification of any nucleic acid sequence.

In this study, we developed a new type of paper-based analytical device (PAD), the three-dimensional (3D) slip-PAD, to detect infectious human norovirus for global healthcare. The 3D configuration of the papers combined with a slip design provides unique features and versatility that overcome the limitations of fluidic manipulation and sensitivity in point-of-care (POC) tests. The assay can be carried out in a single step based on a moveable slip design, making it suitable for unskilled users. The 3D fluidic network developed by layered construction of wax-patterned papers provides different fluidic paths for the sequential delivery of multiple fluids without the need for peripheral equipment. The release and mixing of enhancement reagents on the device improved the sensitivity and detection limit. The assay results could be visualized by naked eye within 10 min, with subsequent amplification of the signal over time (4 copies ml−1 for human norovirus. These results demonstrate that the 3D slip-PAD is a sensitive diagnostic assay for detecting human norovirus infection that is particularly suitable for POC testing in regions where resources are scarce.

A paper-based upconversion fluorescence resonance energy transfer assay device is proposed for sensitive detection of CEA. The device is fabricated on a normal filter paper with simple nano-printing method. Upconversion nanoparticles tagged with specific antibodies are printed to the test zones on the test paper, followed by the introduction of assay antigen. Upconversion fluorescence measurements are directly conducted on the test zones after the antigen-to-antibody reactions. Furthermore, a multi-channel test paper for simultaneous detection of multiple cancer biomarkers was established by the same method and obtained positive results. The device showed high anti-interfere, stability, reproducible and low detection limit (0.89 ng/mL), moreover it is very easy to fabricate and operate, which is a promising prospect for a clinical point-of-care test.

Transparent paper is an alternative substrate for electronic devices due to its unique properties. However, energy-intensive and/or time-consuming procedures currently limit the scalable production of transparent paper. In this report, we demonstrate a rapid process to fabricate optically transparent paper with regenerative cellulose fibers (RCFs) by employing a dissolving-debonding strategy. The RCFs have an average width of 19.3 μm and length of several hundred microns and are prepared into transparent paper by vacuum filtration. This new dissolving-debonding approach enables high production efficiency while creating transparent paper with excellent optical and mechanical properties.

Here we report the vertical paper analytical devices (vPADs) fabricated using the principles of quilling and kirigami. What differentiates the vPADs from conventional paper microfluidic devices is that the paper substrate used to fabricate the device is placed vertically to the device plane. The fabrication of vPADs with high precision is instrument-free, requiring no photolithography, printing or heating. Two- and three-dimensional vPADs are fabricated for multiplex colorimetric assays of four biochemical indicators and automated enzyme-linked immunosorbent assay of human myoglobin, respectively.

Foldable organic memory on cellulose nanofibril paper with bendable and rollable characteristics is demonstrated by employing initiated chemical vapor deposition (iCVD) for polymerization of the resistive switching layer and inkjet printing of the electrode, where iCVD based on all-dry and room temperature process is very suitable for paper electronics. This memory exhibits a low operation voltage of 1.5 V enabling battery operation compared to previous reports and wide memory window. The memory performance is maintained after folding tests, showing high endurance. Furthermore, the quick and complete disposable nature demonstrated here is attractive for security applications. This work provides an effective platform for green, foldable and disposable electronics based on low cost and versatile materials.

We report the transient memory device by means of a water soluble SSG (solid sodium with glycerine) paper. This material has a hydroscopic property hence it can be soluble in water. In terms of physical security of memory devices, prompt abrogation of a memory device which stored a large number of data is crucial when it is stolen because all of things have identified information in the memory device. By utilizing the SSG paper as a substrate, we fabricated a disposable resistive random access memory (RRAM) which has good data retention of longer than 106 seconds and cycling endurance of 300 cycles. This memory device is dissolved within 10 seconds thus it can never be recovered or replicated. By employing direct printing but not lithography technology to aim low cost and disposable applications, the memory capacity tends to be limited less than kilo-bits. However, unlike high memory capacity demand for consumer electronics, the proposed device is targeting for security applications. With this regards, the sub-kilobit memory capacity should find the applications such as one-time usable personal identification, authentication code storage, cryptography key, and smart delivery tag. This aspect is attractive for security and protection system against unauthorized accessibility.

Multiple and complex functionalities are a demand nowadays for almost all materials, including common day-to-day materials such as paper, textiles, wood, etc. In the present report, the surface temperature control of different types of materials, including paper and textiles, was demonstrated by Joule heating of metallic-web transparent electrodes both by direct current and by RF induced eddy currents. Polymeric submicronic fiber webs were prepared by electrospinning, and metal sputtering was subsequently performed to transform them into flexible transparent electrodes. These electrodes were thermally attached to different substrates, including paper, textiles and glass. Using thermochromic inks, we demonstrated a high degree of control of the substrates’ surface temperature by means of the Joule effect. Metallic fiber webs appear to be excellently suited for use as transparent electrodes for controlling the surface temperature of common materials, their highly flexible nature being a major advantage when dealing with rough, bendable substrates. This kind of result could not be achieved on bendable substrates with rough surfaces such as paper or textiles while employing classical transparent electrodes i.e. metal oxides. Moreover, contactless heating with induced currents is a premiere for transparent electrodes and opens up a score of new application fields.

Paper-based writing electronics has received a lot of interest recently due to its potential applications in flexible electronics. To obtain ultra-low resistivity paper-based writing electronics, we developed a kind of ink with high concentration of Ag Nano-particles (up to 80 wt%), as well as a related dispensing writing system consisting an air compressor machine and a dispenser. Additionally, we also demonstrated the writability and practical application of our proposed ink and writing system. Based on the study on the effect of sintering time and pressure, we found the optimal sintering time and pressure to obtain high quality Ag NPs wires. The electrical conductivity of nano-silver paper-based electronics has been tested using the calculated resistivity. After hot-pressure sintering at 120 °C, 25 MPa pressure for 20 minutes, the resistivity of silver NPs conductive tracks was 3.92 × 10−8 (Ωm), only 2.45 times of bulk silver. The mechanical flexibility of nano-silver paper-based electronics also has been tested. After 1000 bending cycles, the resistivity slightly increased from the initial 4.01 × 10−8 to 5.08 × 10−8 (Ωm). With this proposed ink preparation and writing system, a kind of paper-based writing electronics with ultra-low resistivity and good mechanical flexibility was achieved.

X-ray phase and dark-field imaging techniques provide complementary and inaccessible information compared to conventional X-ray absorption or visible light imaging. However, such methods typically require sophisticated experimental apparatus or X-ray beams with specific properties. Recently, an X-ray speckle-based technique has shown great potential for X-ray phase and dark-field imaging using a simple experimental arrangement. However, it still suffers from either poor resolution or the time consuming process of collecting a large number of images. To overcome these limitations, in this report we demonstrate that absorption, dark-field, phase contrast and two orthogonal differential phase contrast images can simultaneously be generated by scanning a piece of abrasive paper in only one direction. We propose a novel theoretical approach to quantitatively extract the above five images by utilising the remarkable properties of speckles. Importantly, the technique has been extended from a synchrotron light source to utilise a lab-based microfocus X-ray source and flat panel detector. Removing the need to raster the optics in two directions significantly reduces the acquisition time and absorbed dose, which can be of vital importance for many biological samples. This new imaging method could potentially provide a breakthrough for numerous practical imaging applications in biomedical research and materials science.

Cellulase (mainly endoglucanase, EG) has been used in pulp modification for improving paper quality through environmentally friendly process. But low activity in alkaline pH and high filter paper activity (FPA) were still obstacles for extending the cellulase application in papermaking industry. In the study, an alkali-tolerant EG gene of Bacillus subtilis Y106 was homologous over-expressed for obtaining suitable enzyme used in pulp modification. The engineering strain could produce the crude enzyme with more alkali-tolerant EG and little PFA. Potential of the crude enzyme in modification of different pulps were investigated. It was found that the enzyme could be used for improving drainage and strength properties of pulps from softwood, hardwood and non-wood materials, especially non-wood pulp such as wheat straw pulp. The underlying mechanisms of pulp modification and different effects on various types of pulps by the EG treatment were also discussed by studying the change in fibers characteristics and fiber bonding.

In this study, actual swage waste activated sludge in batch reactors was employed to assess the synergistic effect of free nitrous acid and Fenton pre-treatments on enhancing methane production in the anaerobic digestion process. In addition to methane enhancement, the mechanisms driving the enhancement were also investigated via measuring enzymes activity and solubilisation of organic matter. This study revealed that the combined pre-treatments solubilised organic matter significantly more than the bioreactors pre-treated with individual FNA and Fenton. For understanding the influence of pre-treatments on solubilisation of organic matter, soluble protein, soluble polysaccharide and soluble chemical oxygen demand (SCOD) were measured before and after the treatments and it was shown that they respectively increased by 973%, 33% and 353% after the treatments. Protease and cellulase activity, as the key constituents of the microbial community in activated sludge, decreased considerably after the combined pre-treatments 42% and 32% respectively, which resulted in considerable methane enhancement. The results corroborate the synergy of the combined FNA and Fenton pre-treatment in degrading the organic and microbial constituents in waste activated sludge, paving the way for the big-scale implementation of these technologies.

Humans have dyed textiles and leather, colored food, and paint body parts using natural dyes throughout history. Natural dyes have suffered drastically due to recent socioeconomic changes and replacement with synthetic dye in the textile industry. Hence, it is urgent to study indigenous dye plants and dyeing craft in local communities to protect these resources' potential ecological, economic, and cultural values. In 11 Monpa villages of Mêdog County, South-east Tibet, China, we conducted field research to record the indigenous method of cloth dyeing using madder dye. An aqueous extract of the root of Rubia wallichiana is a traditional madder dye. In this study, we used traditional dye and ethyl alcohol extract of the residue of aqueous extract. Two fabrics were dyed with the extractions in the presence of one of the metallic mordants or biomordants. Pigment compounds from aqueous extraction of madder and ethyl alcohol extraction of recycled madder were evaluated using Phytochemical, UV–visible spectroscopy, and FTIR test. We carried out One-way ANOVA and Duncan's new multiple range method to analyze different dying approaches and conditions. The dyed fabrics were evaluated by indicators of color strength and fastness, including washing, rubbing, and perspiration. The findings revealed the potentiality of biomordants to improve the dyeing properties of madder. The dyeing properties of recycled madder were marginally better than traditional madder. The results revealed the feasibility of enhancing the dyeing property and reuse of the residue from madder dyeing. The improved dyeing and reuse of residue can improve local ecological, economic benefits, and cultural heritage while applying research findings for the subsequent commercialization of plant dyes.

Industrial development and increased energy requirements have led to high consumption of fossil fuels. Thus, environmental pollution has become a profound problem. Every year, a large amount of agro-industrial, municipal and forest residues are treated as waste, but they can be recovered and used to produce thermal and electrical energy through biological or thermochemical conversion processes. Among the main types of agro-industrial waste, soluble coffee residues represent a significant quantity all over the world. Silver skin and spent coffee grounds (SCG) are the main residues of the coffee industry. The many organic compounds contained in coffee residues suggest that their recovery and use could be very beneficial. Indeed, thanks to their composition, they can be used in the production of biodiesel, as a source of sugar, as a precursor for the creation of active carbon or as a sorbent for the removal of metals. After a careful evaluation of the possible uses of coffee grounds, the aim of this research was to show a broad characterization of coffee waste for energy purposes through physical and chemical analyses that highlight the most significant quality indexes, the interactions between them and the quantification of their importance. Results identify important tools for the qualification and quantification of the effects of coffee waste properties on energy production processes. They show that (SCG) are an excellent raw material as biomass, with excellent values in terms of calorific value and low ash content, allowing the production of 98% coffee pellets that are highly suitable for use in thermal conversion systems. Combustion tests were also carried out in an 80kWth boiler and the resulting emissions without any type of abatement filter were characterized.

Global warming has become a serious issue nowadays as the trend of CO2 emission is increasing by years. In Malaysia, the electricity and energy sector contributed a significant amount to the nation’s CO2 emission due to fossil fuel use. Many research works have been carried out to mitigate this issue, including carbon capture and utilization (CCUS) technology and biological carbon fixation by microalgae. This study makes a preliminary effort to screen native microalgae species in the Malaysian coal-fired power plant’s surrounding towards carbon fixation ability. Three dominant species, including Nannochloropsis sp., Tetraselmis sp., and Isochrysis sp. were identified and tested in the laboratory under ambient and pure CO2 condition to assess their growth and CO2 fixation ability. The results indicate Isochrysis sp. as the superior carbon fixer against other species. In continuation, the optimization study using Response Surface Methodology (RSM) was carried out to optimize the operating conditions of Isochrysis sp. using a customized lab-scale photobioreactor under simulated flue gas exposure. This species was further acclimatized and tested under actual flue gas generated by the power plant. Isochrysis sp. had shown its capability as a carbon fixer with CO2 fixation rate of 0.35 gCO2/L day under actual coal-fired flue gas exposure after cycles of acclimatization phase. This work is the first to demonstrate indigenous microalgae species' ability as a carbon fixer under Malaysian coal-fired flue gas exposure. Thus, the findings shall be useful in exploring the microalgae potential as a biological agent for carbon emission mitigation from power plants more sustainably.

Residues from the wine industry constitute an abundant feedstock for biodiesel production in wine-producing countries. The use of grapeseed oil, together with bioethanol obtained from distillation of wine surplus or grape skins and stalks and wine lees, as reagents in the transesterification reaction, results in a mixture of fatty acid ethyl esters (FAEE), which is a fully renewable, autochthonous, and waste-derived biofuel. In this work, a blend of FAEE produced from grape seed oil with diesel fuel was selected based on a study of fuel properties, and the optimal blend, with 30% v/v of FAEE, was tested in a Euro 6 engine following the Worldwide harmonized Light-duty Test Cycle (WLTC) and a Real Driving Emissions Cycle (RDE), as required in the new certification procedures. Engine performance and emissions from this blend and a commercial diesel fuel were compared. The FAEE blend showed a significant potential to reduce particle emissions, both in mass and number (from 23% in number to 46.5% in mass for WLTC, and from 56% in number to 61% in mass for RDE), and CO (25.5% for WLTC and 39% for RDE) but penalized NOx (32% higher in WLTC and 26.4% higher in RDE).

The behaviour of ash of fuel affects its thermal efficiency when in use. The ash analyses of bio-coal briquettes developed from lean grade coal and torrefied woody biomass have received limited intensive study. Therefore, the present study aims at analysing the ashes of briquette made from lean grade coal and torrefied woody biomass using blended coal tar pitch and molasses as the binder. Bio-coal briquettes were produced from coal and torrefied biomass in various hybrid ratios. Ashing of various briquettes was done in a muffle furnace at 850 °C for 3 h. Mineral phases of the ash were identified using an X-ray Diffractometer (XRD), while the mineral oxides were obtained using an X-ray Fluorescence Spectrometer. The AFT700 Furnace was used with its AFT700 software to evaluate the ash fusion temperatures of the ashes. The XRD patterns look similar, and quartz was found to be the dominant mineral phase present in the raw coal and bio-coal briquettes. The SiO2 (57–58%), Al2O3 (19–21%), and Fe2O3 (8–9%) were the major oxides observed in the ashes. The final fusion temperatures of the ashes range from 1300–1350 °C. The compositions of the ashes of the bio-coal briquettes are classified as detrital minerals. It was concluded that the addition of torrefied biomass (≤ $$10\%)$$ 10 % ) and blended binder ($$\le $$ ≤ 15%) to coal gave a negligible impact on the ashes of the resultant bio-coal briquettes.

Sensor data can be wirelessly transmitted from simple, battery-less tags using Radio Frequency Identification (RFID). RFID sensor tags consist of an antenna, a radio frequency integrated circuit chip (RFIC), and at least one sensor. An ideal tag can communicate over a long distance and be seamlessly integrated onto everyday objects. However, miniaturized antenna designs often have lower performance. Here we demonstrate compact, flexible sensor tags with read range comparable to that of conventional rigid tags. We compare fabrication techniques for flexible antennas and demonstrate that screen and stencil printing are both suitable for fabricating antennas; these different techniques are most useful at different points in the design cycle. We characterize two versions of flexible, screen printed folded dipoles and a meandered monopole operating in the 915 MHz band. Finally, we use these antennas to create passive sensor tags and demonstrate over the air communication of sensor data. These tags could be used to form a network of printed, flexible, passive, interactive sensor tags.

The methods of separation of microalgae has a significant impact in the economic aspects of their cultivation. In this study, pine bark was used as a substrate for immobilization of microalgal biomass cultivated in raw municipal sewage. The experiment was conducted in cylindrical photobioreactors (PBRs) with circulation of wastewater. Biomass was cultivated for 42 days. After that time, abundant growth of the biofilm with microalgae on the surface of pine bark as well as improvement of the quality of treated sewage were observed. The efficiency of removal of nutrients from wastewater was 64–81% for total nitrogen and 97–99% for total phosphorus. Moreover, the concentration of suspended solids in sewage was reduced, which resulted in a decrease in turbidity by more than 90%. Colorimetric analysis and Volatile Matter (VM) content in the substrate showed a decrease in the Higher Heating Value (HHV) and concentration of VM due to the proliferation of biofilm.

Wood chips or particles as well as shredded straw offer desired thermal insulation qualities. When exposed to a humid environment, however, fungal growth on wood and straw is an important consideration. An experimental investigation was conducted in order to evaluate the effectiveness of a simple treatment in mitigating fungal growth on wood- and straw-based insulation. This treatment involved blending of wood chips or particles, or shredded straw with an aerated slurry which offers the potential to mitigate fungal growth on biomass by a combination of physical and chemical effects without imposing a weight penalty. Experimental results verified the effectiveness of this treatment in controlling fungal growth on wood and straw subjected to different moisture conditions.

Competition of volatile fatty acids between anoxic denitrification and anaerobic phosphorus release is prominent. Therefore, low concentration wastewater has restricted effects on nitrogen and phosphorus removal. The purpose of this study is to treat dormitory sewage with a biochemical oxygen demand (BOD) ranging from 50 to 150 mg/L using dewatered alum sludge-based sequencing batch constructed wetland system. Vegetation in the wetland system was chosen to be Phragmites australis. Three parallel cases were carried out to assess impacts due to different hydraulic retention time (HRT) and artificial aeration. The results showed that this system is effective in removing total nitrogen (TN), ammonia nitrogen (NH3-N) and total phosphorus (TP) under different HRT. However, nitrous oxide (N2O) emission poses to be the greatest challenge in the high HRT cases. Artificial aeration could reduce N2O emission but is associated with high operational cost. Results indicate that dewatered alum sludge-based sequencing batch constructed wetland system is a promising bio-measure in the treatment of low concentration wastewater.

Flexible and crystallized indium–tin oxide (ITO) thin films were successfully obtained on plastic polyethylene terephthalate (PET) films with monolayered graphene as a platform. The highly crystalline ITO (c-ITO) was first fabricated on a rigid substrate of graphene on copper foil and it was subsequently transferred onto a PET substrate by a well-established technique. Despite the plasma damage during ITO deposition, the graphene layer effectively acted as a Cu-diffusion barrier. The c-ITO/graphene/PET electrode with the 60-nm-thick ITO exhibited a reasonable sheet resistance of ~45 Ω sq−1 and a transmittance of ~92% at a wavelength of 550 nm. The c-ITO on the monolayered graphene support showed significant enhancement in flexibility compared with the ITO/PET film without graphene because the atomically controlled monolayered graphene acted as a mechanically robust support. The prepared flexible transparent c-ITO/graphene/PET electrode was applied as the anode in a bulk heterojunction polymer solar cell (PSC) to evaluate its performance, which was comparable with that of the commonly used c-ITO/glass electrode. These results represent important progress in the fabrication of flexible transparent electrodes for future optoelectronics applications.

In this paper, we report highly conductive, highly flexible, light weight and low cost printed graphene for wireless wearable communications applications. As a proof of concept, printed graphene enabled transmission lines and antennas on paper substrates were designed, fabricated and characterized. To explore its potentials in wearable communications applications, mechanically flexible transmission lines and antennas under various bended cases were experimentally studied. The measurement results demonstrate that the printed graphene can be used for RF signal transmitting, radiating and receiving, which represents some of the essential functionalities of RF signal processing in wireless wearable communications systems. Furthermore, the printed graphene can be processed at low temperature so that it is compatible with heat-sensitive flexible materials like papers and textiles. This work brings a step closer to the prospect to implement graphene enabled low cost and environmentally friendly wireless wearable communications systems in the near future.

Lightweight, simple and flexible self-powered photodetectors are urgently required for the development and application of advanced optical systems for the future of wearable electronic technology. Here, using a low-temperature reduction process, we report a chemical approach for producing freestanding monolithic reduced graphene oxide papers with different gradients of the carbon/oxygen concentration ratio. We also demonstrate a novel type of freestanding monolithic reduced graphene oxide self-powered photodetector based on a symmetrical metal–semiconductor–metal structure. Upon illumination by a 633-nm continuous wave laser, the lateral photovoltage is observed to vary linfearly with the laser position between two electrodes on the reduced graphene oxide surface. This result may suggest that the lateral photovoltaic effect in the reduced graphene oxide film originates from the built-in electric field by the combination of both the photothermal electric effect and the gradient of the oxygen-to-carbon composition. These results represent substantial progress toward novel, chemically synthesized graphene-based photosensors and suggest one-step integration of graphene-based optoelectronics in the future.

Three different treatment technologies, namely mono-algae culture, algal-bacterial culture, and algal-fungal culture, were applied to remove pollutants form synthetic domestic sewage and to remove CO2 from biogas in a photobioreactor. The effects of different initial influent C/N ratios on microalgal growth rates and pollutants removal efficiencies by the three microalgal cultures were investigated. The best biogas upgrading and synthetic domestic sewage pollutants removal effect was achieved in the algal-fungal system at the influent C/N ratio of 5:1. At the influent C/N ratio of 5:1, the algal-fungal system achieved the highest mean chemical oxygen demand (COD) removal efficiency of 81.92% and total phosphorus (TP) removal efficiency of 81.52%, respectively, while the algal-bacterial system demonstrated the highest mean total nitrogen (TN) removal efficiency of 82.28%. The average CH4 concentration in upgraded biogas and the removal efficiencies of COD, TN, and TP were 93.25 ± 3.84% (v/v), 80.23 ± 3.92%, 75.85 ± 6.61%, and 78.41 ± 3.98%, respectively. These results will provide a reference for wastewater purification ad biogas upgrading with microalgae based technology.

We introduce high-performance metal mesh/graphene hybrid transparent conductive layers (TCLs) using prime-location and metal-doped graphene in near-ultraviolet light-emitting diodes (NUV LEDs). Despite the transparency and sheet resistance values being similar for hybrid TCLs, there were huge differences in the NUV LEDs’ electrical and optical properties depending on the location of the graphene layer. We achieved better physical stability and current spreading when the graphene layer was located beneath the metal mesh, in direct contact with the p-GaN layer. We further improved the contact properties by adding a very thin Au mesh between the thick Ag mesh and the graphene layer to produce a dual-layered metal mesh. The Au mesh effectively doped the graphene layer to create a p-type electrode. Using Raman spectra, work function variations, and the transfer length method (TLM), we verified the effect of doping the graphene layer after depositing a very thin metal layer on the graphene layers. From our results, we suggest that the nature of the contact is an important criterion for improving the electrical and optical performance of hybrid TCLs, and the method of doping graphene layers provides new opportunities for solving contact issues in other semiconductor devices.

Taraditionally, the water-soluble contaminants of biodiesel are treated by water wash method. However, water wash method ends up in an aqueous effluent, which might then cause a harmful environmental impact. As a consequence, waterless purification of biodiesel has triggered primary interest in biodiesel manufacturing process. To address this issue, an endeavour has been made in this work to investigate the waterless purification of biodiesel from waste cooking oil using cow dung ash at different concentration of 1, 2, 3 and 4 wt/wt %. The optimum concentration of cow dung ash for biodiesel purification was found through chemometric analysis by comparing the Fourier transform infrared transmission (FTIR) spectral characteristics of cow dung ash with the water treated FTIR. It was observed from the experimental study that 1 wt/wt % of cow dung ash exhibited similar structural characteristics as that of traditional water treated method of biodiesel purification. Therefore, bio-waste cow dung ash is an effective adsorbent in purifying biodiesel analogous to traditional water washing technology.

The electronic and optical properties of graphene are greatly dependent on the the number of layers. For the precise control of the graphene layers, atomic layer etching (ALE), a cyclic etching method achieved through chemical adsorption and physical desorption, can be the most powerful technique due to barely no damage and no contamination. In this study, we demonstrated the ALE process of graphene layers without noticeably damaging the graphene by using a controlled low energy oxygen (O2+/O+)-ion for chemical adsorption and a low energy Ar+-ion (11.2 eV) for physical desorption. In addition, using a trilayer graphene, mono- and bi-layer graphene could be successfully fabricated after one- and two-cycle ALE of the trilayer graphene, respectively. We believe that the ALE technique presented herein can be applicable to all layered materials such as graphene, black phosphorous and transition metal dichalcogenides which are important for next generation electronic devices.

Sludge management is a major issue for water utilities globally. Poor digestibility and dewaterability are the main factors determining the cost for sludge management, whereas pathogen and toxic metal concentrations limit beneficial reuse. In this study, the effects of low level nitrite addition to acidified sludge to simultaneously enhance digestibility, toxic metal removal, dewaterability and pathogen reduction were investigated. Waste activated sludge (WAS) from a full-scale waste water treatment plant was treated at pH 2 with 10 mg NO2−-N/L for 5 h. Biochemical methane potential tests showed an increase in the methane production of 28%, corresponding to an improvement from 247 ± 8 L CH4/kg VS to 317 ± 1 L CH4/kg VS. The enhanced removal of toxic metals further increased the methane production by another 18% to 360 ± 6 L CH4/kg VS (a total increase of 46%). The solids content of dewatered sludge increased from 14.6 ± 1.4% in the control to 18.2 ± 0.8%. A 4-log reduction for both total coliforms and E. coli was achieved. Overall, this study highlights the potential of acidification with low level nitrite addition as an effective and simple method achieving multiple improvements in terms of sludge management.

Securing a semiconducting bandgap is essential for applying graphene layers in switching devices. Theoretical studies have suggested a created bulk bandgap in a graphene layer by introducing an asymmetry between the A and B sub-lattice sites. A recent transport measurement demonstrated the presence of a bandgap in a graphene layer where the asymmetry was introduced by placing a graphene layer on a hexagonal boron nitride (h-BN) substrate. Similar bandgap has been observed in graphene layers on metal substrates by local probe measurements; however, this phenomenon has not been observed in graphene layers on a near-insulating substrate. Here, we present bulk bandgap-like features in a graphene layer epitaxially grown on an h-BN substrate using scanning tunneling spectroscopy. We observed edge states at zigzag edges, edge resonances at armchair edges, and bandgap-like features in the bulk.

The effect of tetracycline (TC) antibiotic on biogas generation in anaerobic wastewater treatment was studied. A lab-scale Anaerobic Baffled Reactor (ABR) with three compartments was used. The reactor was operated with synthetic wastewater in the absence of TC and in the presence of 250 μg/L TC for 90 days, respectively. The removal rate of TC, volatile fatty acids (VFAs), biogas compositions (hydrogen (H2), methane (CH4), carbon dioxide (CO2)), and total biogas production in each compartment were monitored in the two operational conditions. Results showed that the removal rate of TC was 14.97–67.97% in the reactor. The presence of TC had a large negative effect on CH4 and CO2 generation, but appeared to have a positive effect on H2 production and VFAs accumulation. This response indicated that the methanogenesis process was sensitive to TC presence, but the acidogenesis process was insensitive. This suggested that the presence of TC had less influence on the degradation of organic matter but had a strong influence on biogas generation. Additionally, the decrease of CH4 and CO2 generation and the increase of H2 and VFAs accumulation suggest a promising strategy to help alleviate global warming and improve resource recovery in an environmentally friendly approach.

To pattern electrical metal contacts, electron beam lithography or photolithography are commonly utilized and these processes require polymer resists with solvents. During the patterning process the graphene surface is exposed to chemicals and the residue on the graphene surface was unable to be completely removed by any method, causing the graphene layer to be contaminated. A lithography free method can overcome these residue problems. In this study, we use a micro-grid as a shadow mask to fabricate a graphene based field-effect-transistor (FET). Electrical measurements of the graphene based FET samples are carried out in air and vacuum. It is found that the Dirac peaks of the graphene devices on SiO2 or on hexagonal boron nitride (hBN) shift from a positive gate voltage region to a negative region as air pressure decreases. In particular, the Dirac peaks shift very rapidly when the pressure decreases from ~2 × 10−3 Torr to ~5 × 10−5 Torr within 5 minutes. These Dirac peak shifts are known as adsorption and desorption of environmental gases, but the shift amounts are considerably different depending on the fabrication process. The high gas sensitivity of the device fabricated by shadow mask is attributed to adsorption on the clean graphene surface.

Although graphene is a typical two dimensional materials, it has converted to multi-dimensional materials with many unique properties. As an example, the one dimensional graphene fiber is fabricated by utilizing ionic liquid as coagulation and functional diamines as cross-linkers to connect graphene oxide layers. The fibers show excellent mechanical properties and superior electrical performance. The tensile strength of the resultant fibers reaches ~729 MPa after a super high temperature thermal annealing treatment at 2800 °C. Additionally, quasi-solid-state flexible micro-capacitors are fabricated with promising result on energy storage. The device show a specific volumetric capacity as high as ~225 F/cm3 (measured at 103.5 mA cm−3 in a three-electrode cell), as well as a long cycle life of 2000 times. The initial results indicate that these fibers will be a good candidate to replace energy storage devices for miniaturized portable electronic applications.

The utilization of bioethanol as the alcohol source for biodiesel production is more environmentally advantageous over methanol owing to its lower toxicity, lower flammability and its sustainable supply from renewable agricultural resources. However, as the presence of water in crude bioethanol is the critical factor limiting the biodiesel production process, the energy-intensive and costly purification of bioethanol is necessary for biodiesel application. Manganese glycerolate (MnGly) is reported the first time here as a robust heterogeneous catalyst that exhibited over 90% conversion by using aqueous ethanol containing 80 wt.% of water in the production of fatty acid ethyl ester (FAEE). The employment of 95 wt.% ethanol with respect to water could achieve 99.7% feedstock conversion in 6 hours under the optimal reaction conditions: reaction temperature (150 °C), feedstock-to-ethanol molar ratio (1:20) and catalyst loading (6 wt.%). Commercially available low grade crude bioethanol with the presence of impurities like sugars were applied which demonstrated remarkable catalytic activity in 24 hours. The high water tolerance of MnGly towards biodiesel production could eventually simplify the purification of bioethanol that consumes less energy and production cost.

Porous structure of reduced graphene oxide (rGO) plays an important role in developing flexible graphene-based devices. In this work, we report a novel methodology for reduction of freestanding graphite oxide (GO) sheet by picosecond pulse laser direct writing in liquid nitrogen. Non-agglomerate and porous structure of rGO is fabricated successfully due to frozen effect during laser processing. Compared with laser-irradiated rGO developed in N2 gas at ambient environment, the frozen rGO developed in liquid N2 shows better ordered structure with less defects, crack-free morphology as well as better electron supercapacitor performance including 50–60 Ω/sq in sheet electrical resistance. Mechanism of cryotemperature photoreduction GO is also discussed.

The successful integration of graphene into microelectronic devices is strongly dependent on the availability of direct deposition processes, which can provide uniform, large area and high quality graphene on nonmetallic substrates. As of today the dominant technology is based on Si and obtaining graphene with Si is treated as the most advantageous solution. However, the formation of carbide during the growth process makes manufacturing graphene on Si wafers extremely challenging. To overcome these difficulties and reach the set goals, we proposed growth of high quality graphene layers by the CVD method on Ge(100)/Si(100) wafers. In addition, a stochastic model was applied in order to describe the graphene growth process on the Ge(100)/Si(100) substrate and to determine the direction of further processes. As a result, high quality graphene was grown, which was proved by Raman spectroscopy results, showing uniform monolayer films with FWHM of the 2D band of 32 cm−1.

Single-layer graphene has demonstrated remarkable electronic properties that are strongly influenced by interfacial bonding and break down for the lowest energy configuration of stacked graphene layers (AB Bernal). Multilayer graphene with relative rotations between carbon layers, known as turbostratic graphene, can effectively decouple the electronic states of adjacent layers, preserving properties similar to that of SLG. While the growth of AB Bernal graphene through chemical vapor deposition has been widely reported, we investigate the growth of turbostratic graphene on heteroepitaxial Ni(111) thin films utilizing physical vapor deposition. By varying the carbon deposition temperature between 800 –1100 °C, we report an increase in the graphene quality concomitant with a transition in the size of uniform thickness graphene, ranging from nanocrystallites to thousands of square microns. Combination Raman modes of as-grown graphene within the frequency range of 1650 cm−1 to 2300 cm−1, along with features of the Raman 2D mode, were employed as signatures of turbostratic graphene. Bilayer and multilayer graphene were directly identified from areas that exhibited Raman characteristics of turbostratic graphene using high-resolution TEM imaging. Raman maps of the pertinent modes reveal large regions of turbostratic graphene on Ni(111) thin films at a deposition temperature of 1100 °C.

Green chemistry, sustainability and eco-efficiency are guiding the development of the next generation of industrial chemical processes. The use of non-edible lignocellulosic biomass as a source of chemicals and fuels has recently raised interest due to the need for an alternative to fossil resources. Valorisation mainly focuses on cellulose, which has been used for various industrial scale applications for decades. However, creating an economically more viable value chain would require the exploitation of the other main components, hemicellulose and lignin. Here, we present a new low melting mixture composition based in boric acid and choline chloride and demonstrate its efficiency in the fractionation of wood-based biomass for the production of non-condensed lignin, suitable for further use in the search for sustainable industrial applications and for the selective conversion of hemicelluloses into valuable platform chemicals.

The efficiency of flexible photovoltaic and organic light emitting devices is heavily dependent on the availability of flexible and transparent conductors with at least a similar workfunction to that of Indium Tin Oxide. Here we present the first study of the work function of large area (up to 9 cm2) FeCl3 intercalated graphene grown by chemical vapour deposition on Nickel and demonstrate values as large as 5.1 eV. Upon intercalation, a charge density per graphene layer of 5 ⋅ 1013 ± 5 ⋅ 1012 cm−2 is attained, making this material an attractive platform for the study of plasmonic excitations in the infrared wavelength spectrum of interest to the telecommunication industry. Finally, we demonstrate the potential of this material for flexible electronics in a transparent circuit on a polyethylene naphthalate substrate.

The interface structure of graphene with thermally evaporated metal oxide layers, in particular molybdenum trioxide (MoO3), is studied combining photoemission spectroscopy, sheet resistance measurements and organic light emitting diode (OLED) characterization. Thin (