Search

In developing organic semiconductor polymers for photovoltaic applications, chlorine substitution has become an effective strategy in replacing fluorine substitution to overcome the drawbacks of low yield and high cost, commonly associated with fluorination. In general, several molecular positions are available for chlorination. To obtain a clear understanding of the impact of chlorine substitution on the intrinsic polymer properties, an investigation of structure-property relationships is necessary. Herein, four donor-acceptor type polymers with the same conjugated backbone and flexible alkyl chains, but with chlorine atoms in different positions, are employed to systematically investigate the effect of the site of chlorination on the optoelectronic properties and photovoltaic performance. Substitution of fluorine by chlorine in the backbone slightly increases open circuit voltage (Voc) and fill factor (FF) of the solar cells but causes a loss of short-circuit current density (Jsc). The introduction of chlorine in the conjugated side chains, however, significantly improves Voc, FF, and power conversion efficiency, benefiting from a lower HOMO energy level, efficient and well-balanced transport properties, and superior nanoscale morphology. This journal is

Building on our previous works that compared the efficacy of terpolymers vs. ternary blends in improving the performance of bulk heterojunction organic solar cells, the final piece of this series of studies focuses on comparing terpolymer and ternary blends constructed with two polymers with structurally similar backbones (monoCNTAZ and FTAZ) yet markedly different open circuit voltage (Voc) values. Terpolymers and ternary blends of five different ratios were studied and the results demonstrate that while the overall performance of both the systems is similar, the ternary blends exhibit higher short circuit current (Jsc) values, while the terpolymers exhibit higher Voc values. Investigation of the charge transfer state using low-energy external quantum efficiency (EQE) indicates that the ternary blends are governed by a parallel-like mechanism, while the terpolymer does not follow this mechanism. The key morphological difference between the systems, as elucidated by resonance soft X-ray scattering (RSoXS), is the slightly smaller size (∼60 nm) of domains in the ternary blends compared to that of the terpolymer (∼80 nm), which may affect exciton harvesting in the terpolymer system and lead to lower Jsc values. In addition, a lower driving force for the formation of charge transfer (CT) state is also likely to contribute to the lower Jsc values in the terpolymer system. All together, the data show that structurally similar (perhaps even miscible) polymers still exhibit key differences in performance when paired in terpolymers vs. ternary blends and allow us to further illuminate the underlying mechanisms of such complex systems.

Indoor photovoltaics (IPVs) are garnering increasing attention from both the academic and industrial communities due to the pressing demand of the ecosystem of Internet-of-Things. All-polymer solar cells (all-PSCs), emerging as a sub-type of organic photovoltaics, with the merits of great film-forming properties, remarkable morphological and light stability, hold great promise to simultaneously achieve high efficiency and long-term operation in IPV's application. However, the dearth of polymer acceptors with medium-bandgap has impeded the rapid development of indoor all-PSCs. Herein, a highly efficient medium-bandgap polymer acceptor (PYFO-V) is reported through the synergistic effects of side chain engineering and linkage modulation and applied for indoor all-PSCs operation. As a result, the PM6:PYFO-V-based indoor all-PSC yields the highest efficiency of 27.1% under LED light condition, marking the highest value for reported binary indoor all-PSCs to date. More importantly, the blade-coated devices using non-halogenated solvent (o-xylene) maintain an efficiency of over 23%, demonstrating the potential for industry-scale fabrication. This work not only highlights the importance of fine-tuning intramolecular charge transfer effect and intrachain coplanarity in developing high-performance medium-bandgap polymer acceptors but also provides a highly efficient strategy for indoor all-PSC application., (© 2024 The Author(s). Advanced Materials published by Wiley‐VCH GmbH.)

Owing to the use of cost-effective materials and excellent stability, nonfullerene polymer solar cells (PSCs) have great potential for realizing large-area industrial production. In contrast to fullerene-based devices, non-fullerene PSCs have exhibited a superior photovoltaic performance with up to 12% efficiency and long-term thermal stability. Presently, one of the major factors hindering industrial production is the high sensitivity of the power conversion efficiency (PCE) to thickness variations, which can significantly affect the manufacturing yields and production costs of roll-to-roll processing. Specifically, the device fill factors and PCEs of many high-efficiency nonfullerene PSCs show a significant loss when the thickness of the active layer is over 100 nm. In order to achieve high output capabilities earlier, there is an urgent need to find a processing method to fabricate high-efficiency thick-film nonfullerene PSCs. Controlling the morphology and performance sensitivity in thick-film non-fullerene devices is a great challenge in the field. Here, we present a simple morphology optimization method via thermal annealing to fabricate highly efficient thickness-insensitive non-fullerene PSCs. After this treatment, PBDB-T/IT-M-based nonfullerene PSCs can afford an impressive PCE of up to ∼9.4% at an active layer thickness of 250 nm. In addition, the devices with an active layer thickness of 400 nm still maintain a high efficiency close to 9%. The photovoltaic properties and morphology parameters resolved from hard and soft X-ray scattering clearly indicate that thermal annealing plays a key role in improving the film thickness insensitivity for non-fullerene PSCs.

Cleavable side chain based conjugated polymers (CSCPs) represent a unique approach to offering solution processability with added benefits via the elimination of insulating side chains. This work highlights an optimally designed polythiophene-carboxylic acid based CSCP, POET-T2-COOH, which achieves a conductivity exceeding 350 S/cm in molecularly doped and side chain cleaved films, 100-100,000 times higher than three other structurally isomeric CSCPs. The high conductivity of POET-T2-COOH is accomplished via a new "cleavage with doping" methodology, synergistically combining a strong acid and a primary dopant. This hybrid method achieves the greatest conductivity in all isomeric CSCPs over conventional doping or cleavage techniques. The doped and side chain cleaved POET-T2-COOH displays a stable conductivity in inert atmospheres and a high work function of 5.3 eV, opening up new applications.

Conjugated block copolymers provide a pathway to achieve thermally stable nanostructured thin films for organic solar cells. We characterized the structural evolution of poly(3-hexylthiophene)-block-poly(diketopyrrolopyrrole-terthiophene) (P3HT-b-DPPT-T) from solution to nanostructured thin films. Aggregation of the DPPT-T block of P3HT-b-DPPT-T was found in solution by small-angle X-ray scattering with the P3HT block remaining well-solvated. The nanostructure in thin films was determined using a combination of wide and small-angle X-ray scattering techniques as a function of processing conditions. The structure in solution controlled the initial nanostructure in spin-cast thin films, allowing subsequent thermal annealing processes to further improve the ordering. In contrast to the results for thin films, nanostructural ordering was not observed in the bulk samples by small-angle X-ray scattering. These results suggest the importance of controlling solvent induced aggregation in forming nanostructured thin films of conjugated block copolymers.

This study discusses using FTK Imager software for live forensic investigations in order to track and analyze Remote Access Trojan assaults. In addition to helping organizations safeguard their assets and data against harmful cyberattacks, our research aims to improve computer system security. The knowledge of the presence of the Remote Access Trojan virus, notwithstanding its removal, is the advantage of this research. Installation of Kali Linux, forensic analysis using FTK Imager, and the development and usage of viruses are all part of this study methodology. The process included installing Kali Linux as a platform for the creation and execution of viruses, identifying and analyzing the presence of viruses using FTK Imager, and identifying and analyzing Remote Access Trojan attacks using disk and memory forensic analysis techniques. The research findings indicate that as soon as the target opens the generated virus, the executor gains complete access to the target machine. This allows the executor to follow the target around and record everything it does. As a forensic investigation tool, FTK Imager must be installed on the target in order to detect the virus that the executor developed. The target will thus find it simpler to use memory forensics or disk forensics to look for files created by the executor. describes how to use FTK Imager software to observe and analyze Remote Access Trojan assaults for use in real-world forensic investigations. [ABSTRACT FROM AUTHOR]

Device-level implementation of soft materials for energy conversion and thermal management demands a comprehensive understanding of their thermal conductivity and elastic modulus to mitigate thermo-mechanical challenges and ensure long-term stability. Thermal conductivity and elastic modulus are usually positively correlated in soft materials, such as amorphous macromolecules, which poses a challenge to discover materials that are either soft and thermally conductive or hard and thermally insulative. Here, we show anomalous correlations of thermal conductivity and elastic modulus in two-dimensional (2D) hybrid organic-inorganic perovskites (HOIP) by engineering the molecular interactions between organic cations. By replacing conventional alkyl-alkyl and aryl-aryl type organic interactions with mixed alkyl-aryl interactions, we observe an enhancement in elastic modulus with a reduction in thermal conductivity. This anomalous dependence provides a route to engineer thermal conductivity and elastic modulus independently and a guideline to search for better thermal management materials. Further, introducing chirality into the organic cation induces a molecular packing that leads to the same thermal conductivity and elastic modulus regardless of the composition across all half-chiral 2D HOIPs. This finding provides substantial leeway for further investigations in chiral 2D HOIPs to tune optoelectronic properties without compromising thermal and mechanical stability.

Somatic hybrids between human cells and the Chinese hamster ovary (CHO) K1 mutant, Ade -H cells, were selected for purine prototrophy by growth in adenine-free medium. The Ade -H mutant is defective in the enzyme adenylosuccinate (AMPS) synthetase (ADSS; EC 6.3.4.4), which carries out the first of a two-step sequence in the biosynthesis of AMP from IMP, and therefore requires exogenous adenine for growth. The presence of the long arm of human chromosome 1 in the hybrids is 100% concordant for the ability to grow in adenine-free medium and restoration of the enzyme activity. Hybrid segregants that lose the ability to grow in adenine-free medium lose all or a portion of chromosome 1 and enzyme activity. Southern blot hybridization with a chromosome 1-specific probe, BCMI, confirms the existence of human chromosome 1 in these hybrids. Analysis of a human/CHO translocation chromosome that arose in one of the hybrids suggests that the gene correcting the defect lies in the region 1 cen-1q12. In summary, we have shown by cytogenetics, segregant analysis, biochemical assay, and Southern blot analysis that human chromosome 1, most likely in the region 1cen-1q12, corrects the defect in ADSS-deficient mutant Ade-H cells.

Flexible electronics have received considerable attention in the past decades due to their promising application in rollable display screens, wearable devices, implantable devices, and other electronic applications. In particular, conjugated polymers are favored for flexible electronics due to their mechanical flexibility and potential for solution-processed fabrication techniques, such as blade-coating, roll-to-roll printing, and high-throughput printing allowing for high-performance transistor devices. Thiophene is the prevailing conjugated unit to construct these conjugated polymers due to its favorable electronic properties. On the other hand, furans are among the few conjugated moieties that are easily derived from bio renewable resources. To promote sustainability, we selectively introduced furan into the conjugated backbone of a high-mobility polymer scaffold and systematically studied the effect on the microstructure and charge transport. We show that partially and selectively replacing thiophene units with furan can yield nearly comparable performance compared to the all-thiophene polymer. This strategy offers an improvement in the sustainability of the polymer by incorporating bio-sourced furan without sacrificing the high-performance characteristics. Meanwhile, polymers with incorrect or complete furan incorporation show reduced mobilities. This work serves to develop coherent structure-morphology-performance relationships; such knowledge will establish guidelines for the future development of sustainable, furan-based conjugated materials., (© 2024 Wiley-VCH GmbH.)

The rapid loss of global biodiversity can greatly affect the normal functioning of ecosystems. However, how biodiversity losses affect plant community structure and soil nutrients is unclear. We conducted a field experiment to examine the short- and long-term effects of removing plant functional groups (Gramineae, Cyperaceae, legumes, and forbs) on the interrelationships among the species diversity, productivity, community structure, and soil nutrients in an alpine meadow ecosystem at Menyuan County, Qinghai Province. The variations in the species richness, above- and belowground biomass of the community gradually decreased over time. Species richness and productivity were positively correlated, and this correlation tended to be increasingly significant over time. Removal of the Cyperaceae, legumes, and other forbs resulted in fewer Gramineae species in the community. Soil total nitrogen, phosphorus, organic matter, and moisture contents increased significantly in the legume removal treatment. The removal of other forbs led to the lowest negative cohesion values, suggesting that this community may have difficulty recovering its previous equilibrium state within a short time. The effects of species removal on the ecosystem were likely influenced by the species structure and composition within the community. Changes in the number of Gramineae species indicated that they were more sensitive and less resistant to plant functional group removal. Legume removal may also indirectly cause distinct community responses through starvation and compensation effects. In summary, species loss at the community level led to extensive species niche shifts, which caused community resource redistribution and significant changes in community structure., Competing Interests: The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper. In addition, the publication is approved by all authors., (© 2024 The Authors. Ecology and Evolution published by John Wiley & Sons Ltd.)

Power conversion efficiency (PCE) of organic solar cells (OSCs) processed by nonhalogenated solvents is unsatisfactory due to the unfavorable morphology. Herein, two new small molecule acceptors (SMAs) Y6-Ph and L8-Ph are synthesized by introducing a phenyl end group in the inner side chains of the SMAs of Y6 and L8-BO, respectively, for overcoming the excessive aggregation of SMAs in the long-time film forming processed by nonhalogenated solvents. First, the effect of the film forming time on the aggregation property and photovoltaic performance of Y6, L8-BO, Y6-Ph, and L8-Ph is studied by using the commonly used solvents: chloroform (CF) (rapid film forming process) and chlorobenzene (CB) (slow film forming process). It is found that Y6- and L8-BO-based OSCs exhibit a dramatic drop in PCE from CF- to CB-processed devices owing to the large phase separation, while the Y6-Ph and L8-Ph based OSCs show obviously increased PCEs Furthermore, L8-Ph-based OSCs processed by nonhalogenated solvent o-xylene (o-XY) achieved a high PCE of 18.40% with an FF of 80.11%. The results indicate that introducing a phenyl end group in the inner side chains is an effective strategy to modulate the morphology and improve the photovoltaic performance of the OSCs processed by nonhalogenated solvents., (© 2023 Wiley-VCH GmbH.)

Polymerization of Y6-type acceptor molecules leads to bulk-heterojunction organic solar cells with both high power-conversion efficiency and device stability, but the underlying mechanism remains unclear. Here we show that the exciton recombination dynamics of polymerized Y6-type acceptors (Y6-PAs) strongly depends on the degree of aggregation. While the fast exciton recombination rate in aggregated Y6-PA competes with electron-hole separation at the donor-acceptor (D-A) interface, the much-suppressed exciton recombination rate in dispersed Y6-PA is sufficient to allow efficient free charge generation. Indeed, our experimental results and theoretical simulations reveal that Y6-PAs have larger miscibility with the donor polymer than Y6-type small molecular acceptors, leading to D-A percolation that effectively prevents the formation of Y6-PA aggregates at the interface. Besides enabling high charge generation efficiency, the interfacial D-A percolation also improves the thermodynamic stability of the blend morphology, as evident by the reduced device "burn-in" loss upon solar illumination., (© 2024. The Author(s).)

Series of giant molecule acceptors DY, TY and QY with two, three and four small molecule acceptor subunits are synthesized by a stepwise synthetic method and used for systematically investigating the influence of subunit numbers on the structure-property relationship from small molecule acceptor YDT to giant molecule acceptors and to polymerized small molecule acceptor PY-IT. Among these acceptors-based devices, the TY-based film shows proper donor/acceptor phase separation, higher charge transfer state yield and longer charge transfer state lifetime. Combining with the highest electron mobility, more efficient exciton dissociation and lower charge carrier recombination properties, the TY-based device exhibits the highest power conversion efficiency of 16.32%. These results indicate that the subunit number in these acceptors has significant influence on their photovoltaic properties. This stepwise synthetic method of giant molecule acceptors will be beneficial to diversify their structures and promote their applications in high-efficiency and stable organic solar cells., (© 2023. The Author(s).)

We report on the use of molecular acceptors (MAs) and donor polymers processed with a biomass-derived solvent (2-methyltetrahydrofuran, 2-MeTHF) to facilitate bulk heterojunction (BHJ) organic photovoltaics (OPVs) with power conversion efficiency (PCE) approaching 15%. Our approach makes use of two newly designed donor polymers with an opened ring unit in their structures along with three molecular acceptors (MAs) where the backbone and sidechain were engineered to enhance the processability of BHJ OPVs using 2-MeTHF, as evaluated by an analysis of donor-acceptor (D-A) miscibility and interaction parameters. To understand the differences in the PCE values that ranged from 9-15% as a function of composition, the surface, bulk, and interfacial BHJ morphologies were characterized at different length scales using atomic force microscopy, grazing-incidence wide-angle X-ray scattering, resonant soft X-ray scattering, X-ray photoelectron spectroscopy, and 2D solid-state nuclear magnetic resonance spectroscopy. Our results indicate that the favorable D-A intermixing that occurs in the best performing BHJ film with an average domain size of ∼25 nm, high domain purity, uniform distribution and enhanced local packing interactions - facilitates charge generation and extraction while limiting the trap-assisted recombination process in the device, leading to high effective mobility and good performance.

High-efficiency organic solar cells are often achieved using toxic halogenated solvents and additives that are constrained in organic solar cells industry. Therefore, it is important to develop materials or processing methods that enabled highly efficient organic solar cells processed by halogen free solvents. In this paper, we report an innovative processing method named auxiliary sequential deposition that enables 19%-efficiency organic solar cells processed by halogen free solvents. Our auxiliary sequential deposition method is different from the conventional blend casting or sequential deposition methods in that it involves an additional casting of dithieno[3,2-b:2',3'-d]thiophene between the sequential depositions of the donor (D18-Cl) and acceptor (L8-BO) layers. The auxiliary sequential deposition method enables dramatic performance enhancement from 15% to over 18% compared to the blend casting and sequential deposition methods. Furthermore, by incorporating a branched-chain-engineered acceptor called L8-BO-X, device performance can be boosted to over 19% due to increased intermolecular packing, representing top-tier values for green-solvent processed organic solar cells. Comprehensive morphological and time-resolved characterizations reveal that the superior blend morphology achieved through the auxiliary sequential deposition method promotes charge generation while simultaneously suppressing charge recombination. This research underscores the potential of the auxiliary sequential deposition method for fabricating highly efficient organic solar cells using environmentally friendly solvents., (© 2023. The Author(s).)

While crystalline 2D metal halide perovskites (MHPs) represent a well-celebrated semiconductor class, supporting applications in the fields of photovoltaics, emitters, and sensors, the recent discovery of glass formation in an MHP opens many new opportunities associated with reversible glass-crystalline switching, with each state offering distinct optoelectronic properties. However, the previously reported [ S -(-)-1-(1-naphthyl)ethylammonium] 2 PbBr 4 perovskite is a strong glass former with sluggish glass-crystal transformation time scales, pointing to a need for glassy MHPs with a broader range of compositions and crystallization kinetics. Herein we report glass formation for low-melting-temperature 1-MeHa 2 PbI 4 (1-MeHa = 1-methyl-hexylammonium) using ultrafast calorimetry, thereby extending the range of MHP glass formation across a broader range of organic (fused ring to branched aliphatic) and halide (bromide to iodide) compositions. The importance of a slight loss of organic and hydrogen iodide components from the MHP in stabilizing the glassy state is elucidated. Furthermore, the underlying kinetics of glass-crystal transformation, including activation energies, crystal growth rate, Angell plot, and fragility index, is studied using a combination of kinetic, thermodynamic, and rheological modeling techniques. An inferred fast crystal growth rate of 0.21 m/s for 1-MeHa 2 PbI 4 shows promise toward suitability in extended application spaces, for example, in metamaterials, nonvolatile memory, and optical and neuromorphic computing devices.

It has been reported recently that conjugated polymer:small molecule systems might exhibit complex, re-entrant phase behavior with hourglass or closed-loop miscibility gaps due to an 'apparent' lower critical solution temperature branch. However, the study did not firmly establish if the observations were reflecting equilibrium or not. To assure that the observed shapes of the binodals via a mixing experiment represent local near-equilibrium conditions that capture complex molecular interactions or equation-of-state effects, we present here the liquidus and the binodal for the exact same systems, i.e. , PTB7-Th:PC 61 BM, PffBT4T-C9C13:PC 71 BM and PTB7-Th:EH-IDTBR, with the liquidus measured via a demixing experiment with long annealing time of days to weeks. We observe that the binodal displayed consistent trends with the liquidus, revealing an underlying thermodynamic and not microstructural or kinetic cause behind the complex phase behavior. Our results highlight the need for a novel, sufficiently complex physical model for understanding these non-trivial phase diagrams of semi-conducting materials. We also discover that the composition difference (Δ ϕ ) between liquidus and binodal reflects the crystalline-amorphous interaction, exhibiting a linear relationship with the binodal composition ( ϕ b,polymer ), i.e. , Δ ϕ increases as χ aa decreases. This possibly provides a new approach for obtaining the crystalline-amorphous interaction parameter χ ca ( T ) beyond the commonly used melting point depression method, which estimates χ ca near the melting temperature T m of the crystalline component. The capability of obtaining χ ca ( T ) over a more extended temperature range may encourage more extensive studies and facilitate the understanding of χ ca in general, but particularly for all the novel non-fullerene acceptors that are able to crystallize.

Polymerization sites of small molecule acceptors (SMAs) play vital roles in determining device performance of all-polymer solar cells (all-PSCs). Different from our recent work about fluoro- and bromo- co-modified end group of IC-FBr (a mixture of IC-FBr1 and IC-FBr2), in this paper, we synthesized and purified two regiospecific fluoro- and bromo- substituted end groups (IC-FBr-o & IC-FBr-m), which were then employed to construct two regio-regular polymer acceptors named PYF-T-o and PYF-T-m, respectively. In comparison with its isomeric counterparts named PYF-T-m with different conjugated coupling sites, PYF-T-o exhibits stronger and bathochromic absorption to achieve better photon harvesting. Meanwhile, PYF-T-o adopts more ordered inter-chain packing and suitable phase separation after blending with the donor polymer PM6, which resulted in suppressed charge recombination and efficient charge transport. Strikingly, we observed a dramatic performance difference between the two isomeric polymer acceptors PYF-T-o and PYF-T-m. While devices based on PM6:PYF-T-o can yield power conversion efficiency (PCE) of 15.2 %, devices based on PM6:PYF-T-m only show poor efficiencies of 1.4 %. This work demonstrates the success of configuration-unique fluorinated end groups in designing high-performance regular polymer acceptors, which provides guidelines towards developing all-PSCs with better efficiencies., (© 2021 Wiley-VCH GmbH.)

Reducing the energy loss of sub-cells is critical for high performance tandem organic solar cells, while it is limited by the severe non-radiative voltage loss via the formation of non-emissive triplet excitons. Herein, we develop an ultra-narrow bandgap acceptor BTPSeV-4F through replacement of terminal thiophene by selenophene in the central fused ring of BTPSV-4F, for constructing efficient tandem organic solar cells. The selenophene substitution further decrease the optical bandgap of BTPSV-4F to 1.17 eV and suppress the formation of triplet exciton in the BTPSV-4F-based devices. The organic solar cells with BTPSeV-4F as acceptor demonstrate a higher power conversion efficiency of 14.2% with a record high short-circuit current density of 30.1 mA cm -2 and low energy loss of 0.55 eV benefitted from the low non-radiative energy loss due to the suppression of triplet exciton formation. We also develop a high-performance medium bandgap acceptor O1-Br for front cells. By integrating the PM6:O1-Br based front cells with the PTB7-Th:BTPSeV-4F based rear cells, the tandem organic solar cell demonstrates a power conversion efficiency of 19%. The results indicate that the suppression of triplet excitons formation in the near-infrared-absorbing acceptor by molecular design is an effective way to improve the photovoltaic performance of the tandem organic solar cells., (© 2023. The Author(s).)

Mixing a sterically bulky, electron-transporting host material into a conventional single host-guest emissive layer is demonstrated to suppress phase separation of the host matrix while increasing the efficiency and operational lifetime of deep-blue phosphorescent organic light-emitting diodes (PHOLEDs) with chromaticity coordinates of (0.14, 0.15). The bulky host enables homogenous mixing of the molecules comprising the emissive layer while suppressing single host aggregation; a significant loss channel of nonradiative recombination. By controlling the amorphous phase of the host-matrix morphology, the mixed-host device achieves a significant reduction in nonradiative exciton decay, resulting in 120 ± 6% increase in external quantum efficiency relative to an analogous, single-host device. In contrast to single host PHOLEDs where electrons are transported by the host and holes by the dopants, both charge carriers are conducted by the mixed host, reducing the probability of exciton annihilation, thereby doubling of the deep-blue PHOLED operational lifetime. These findings demonstrate that the host matrix morphology affects almost every aspect of PHOLED performance., (© 2023 Wiley-VCH GmbH.)

All-polymer solar cells (all-PSCs) have drawn growing attention and achieved tremendous progress recently, but their power conversion efficiency (PCE) still lags behind small-molecule-acceptor (SMA)-based PSCs due to the relative difficulty on morphology control of polymer photoactive blends. Here, low-cost PTQ10 is introduced as a second polymer donor (a third component) into the PM6:PY-IT blend to finely tune the energy-level matching and microscopic morphology of the polymer blend photoactive layer. The addition of PTQ10 decreases the π-π stacking distance, and increases the π-π stacking coherence length and the ordered face-on molecular packing orientation, which improves the charge separation and transport in the photoactive layer. Moreover, the deeper highest occupied molecular orbital energy level of the PTQ10 polymer donor than PM6 leads to higher open-circuit voltage of the ternary all-PSCs. As a result, a PCE of 16.52% is achieved for ternary all-PSCs, which is one of the highest PCEs for all-PSCs. In addition, the ternary devices exhibit a high tolerance of the photoactive layer thickness with high PCEs of 15.27% and 13.91% at photoactive layer thickness of ≈205 and ≈306 nm, respectively, which are the highest PCEs so far for all-PSCs with a thick photoactive layer., (© 2022 Wiley-VCH GmbH.)

Developing high-performance donor polymers is important for nonfullerene organic solar cells (NF-OSCs), as state-of-the-art nonfullerene acceptors can only perform well if they are coupled with a matching donor with suitable energy levels. However, there are very limited choices of donor polymers for NF-OSCs, and the most commonly used ones are polymers named PM6 and PM7, which suffer from several problems. First, the performance of these polymers (particularly PM7) relies on precise control of their molecular weights. Also, their optimal morphology is extremely sensitive to any structural modification. In this work, a family of donor polymers is developed based on a random polymerization strategy. These polymers can achieve well-controlled morphology and high-performance with a variety of chemical structures and molecular weights. The polymer donors are D-A1-D-A2-type random copolymers in which the D and A1 units are monomers originating from PM6 or PM7, while the A2 unit comprises an electron-deficient core flanked by two thiophene rings with branched alkyl chains. Consequently, multiple cases of highly efficient NF-OSCs are achieved with efficiencies between 16.0% and 17.1%. As the electron-deficient cores can be changed to many other structural units, the strategy can easily expand the choices of high-performance donor polymers for NF-OSCs., (© 2020 Wiley-VCH GmbH.)

With power conversion efficiency now over 17%, a long operational lifetime is essential for the successful application of organic solar cells. However, most non-fullerene acceptors can crystallize and destroy devices, yet the fundamental underlying thermodynamic and kinetic aspects of acceptor crystallization have received limited attention. Here, room-temperature (RT) diffusion coefficients of 3.4 × 10 -23 and 2.0 × 10 -22 are measured for ITIC-2Cl and ITIC-2F, two state-of-the-art non-fullerene acceptors. The low coefficients are enough to provide for kinetic stabilization of the morphology against demixing at RT. Additionally profound differences in crystallization characteristics are discovered between ITIC-2F and ITIC-2Cl. The differences as observed by secondary-ion mass spectrometry, differential scanning calorimetry (DSC), grazing-incidence wide-angle X-ray scattering, and microscopy can be related directly to device degradation and are attributed to the significantly different nucleation and growth rates, with a difference in the growth rate of a factor of 12 at RT. ITIC-4F and ITIC-4Cl exhibit similar characteristics. The results reveal the importance of diffusion coefficients and melting enthalpies in controlling the growth rates, and that differences in halogenation can drastically change crystallization kinetics and device stability. It is furthermore delineated how low nucleation density and large growth rates can be inferred from DSC and microscopy experiments which could be used to guide molecular design for stability., (© 2020 Wiley-VCH GmbH.)

The integration of semi-transparent organic solar cells (ST-OSCs) in greenhouses offers new agrivoltaic opportunities to meet the growing demands for sustainable food production. The tailored absorption/transmission spectra of ST-OSCs impacts the power generated as well as crop growth, development and responses to the biotic and abiotic environments. To characterize crop responses to ST-OSCs, we grew lettuce and tomato, traditional greenhouse crops, under three ST-OSC filters that create different light spectra. Lettuce yield and early tomato development are not negatively affected by the modified light environment. Our genomic analysis reveals that lettuce production exhibits beneficial traits involving nutrient content and nitrogen utilization while select ST-OSCs impact regulation of flowering initiation in tomato. These results suggest that ST-OSCs integrated into greenhouses are not only a promising technology for energy-neutral, sustainable and climate-change protected crop production, but can deliver benefits beyond energy considerations., Competing Interests: The authors declare that the research was conducted in the absence of any commercial or financial relationships that could be construed as a potential conflict of interest., (Copyright © 2023 Charles, Edwards, Ravishankar, Calero, Henry, Rech, Saravitz, You, Ade, O’Connor and Sederoff.)

Understanding excited-state reorganization energies, exciton diffusion lengths and non-radiative (NR) recombination, and the overall optoelectronic responses of nonfullerene small molecule acceptors (NF-SMAs) is important in order to rationally design new materials with controlled properties. While the effects of structural modifications on the optical gaps and electron affinities of NF-SMAs have been studied extensively, analyses of their absorption spectra that carefully characterize electronic and vibrational contributions that allow comparisons of reorganization energies and their implications for exciton diffusion lengths and NR recombination have yet to be reported. Here, we study the room temperature absorption spectra of three structural classes of NF-SMAs in dilute solutions through multiparameter Franck Condon (MFC) analyses and density functional theory (DFT) calculations. We show that the absorption spectra of these NF-SMAs can be categorized based on molecular structure-spectra correlation. The absorption spectra of curved, Y6-like structures can be described using an MFC model with two electronic transitions and two effective vibrational modes. The results of MFC/DFT analyses reveal that Y6 exhibits the smallest intra-molecular reorganization energy among the materials studied. Linear ITIC-like molecular structures reveal larger reorganization energies and reduced conformational uniformity compared to Y6. Meanwhile structures such as IDTBR and IEICO, which have an extra π-conjugated moiety between the donor and acceptor moieties, have large excited-state reorganization energies and low degrees of conformational uniformity. Since the intra-molecular reorganization energy is correlated with exciton diffusion length and nonradiative voltage losses (Δ V nr ), our results highlight the power of RT absorption spectroscopy and DFT calculations as simple tools to designing improved OSCs materials with small reorganization energies, small Δ V nr , large exciton diffusion length and low energetic disorder (due to a strongly dominant conformation).

[sup.13]C labeling is introduced as a tracer for depth profiling of polymer films and multilayers using secondary ion mass spectrometry (SIMS). Deuterium substitution has traditionally been used in depth profiling of polymers but can affect the phase behavior of the polymer constituents with reported changes in both bulk-phase behavior and surface and interracial interactions. SIMS can provide contrast by examining various functional groups, chemical moieties, or isotopic labels, [sup.C]-Labeled PS ([sup.13]C-PS) and unlabeled PS ([sup.12]C-PS) and PMMA were synthesized using atom-transfer radical polymerization and assembled in several model thin-film systems. Depth profiles were recorded using a Cameca IMS-6f magnetic sector mass spectrometer using both 6.0-keV impact energy [Cs.sup.+] and 5.5-keV impact energy [O.sub.2.sup.+] primary ion bombardment with detection of negative and positive secondary ions, respectively. Although complete separation of [sup.12][C.sup.1]H from [sup.13]C is achieved using both primary ion species, 6.0-keV [Cs.sup.+] clearly shows improved detection sensitivity and signal-to-noise ratio for detection of [sup.12]C, [sup.12][C.sup.1]H, and [sup.13]C secondary ions. The use of [Cs.sup.+] primary ion bombardment results in somewhat anomalous, nonmonotonic changes in the [sup.12]C, [sup.12][C.sup.1]H, and [sup.13]C secondary ion yields through the PS/PMMA interface; however, it is shown that this behavior is not due to sample charging. Through normalization of the [sup.13]C secondary ion yield to the total C ([sup.12]C + [sup.13]C) ion yield, the observed effects through the PS/PMMA interface can be greatly minimized, thereby significantly improving analysis of polymer films and multilayers using SIMS. Mass spectra of [sup.13]C-PS and [sup.12]C-PS were also analyzed using a PHI TRIFF I time-of-flight mass spectrometer, with 15-keV [Ga.sup.+] primary ion bombardment and detection of positive secondary ions. The [sup.12][C.sub.7.sup.1][H.sub.7] ion fragment and its [sup.13]C-enriched analogues have significant secondary ion yields with negligible mass interferences, providing an early indication of the potential for future use of this technique for cluster probe depth profiling of high molecular weight [sup.13]C-labeled fragments.

An ultrathin (

Conjugated polymers have a long history of exploration and use in organic solar cells, and over the last twenty-five years, marked increases in the solar cell efficiency have been achieved. However, the synthetic complexity of these materials has also drastically increased, which makes the scalability of the highest-efficiency materials difficult. If conjugated polymers could be designed to exhibit both high efficiency and straightforward synthesis, the road to commercial reality would be more achievable. For that reason, a new synthetic approach was designed towards PTQ10 (=poly[(thiophene)-alt-(6,7-difluoro-2-(2-hexyldecyloxy)quinoxaline)]). The new synthetic approach to make PTQ10 brought a significant reduction in cost (1/7th the original) and could also easily accommodate different side chains to move towards green processing solvents. Furthermore, high-efficiency organic solar cells were demonstrated with a PTQ10:Y6 blend exhibiting approximately 15 % efficiency., (© 2021 Wiley-VCH GmbH.)

Carbonyl core (C 1S, O1S) --> pi c=o transitions are distinctive in the near-edge X-ray absorption fine structure (NEXAFS) spectra of organic molecules. The chemical sensitivity of these features in C 1s and O 1s NEXAFS spectra is explored for a series of polymers containing the carbonyl group.