Search

Abstract Objectives Microleakage in direct dental restorations is a primary causal factor in the restoration's failure. The aim of this study was to evaluate whether the technique for occlusal layering of the composite resin (the use of brush adaptation, the use of magnification, cusp build‐up, stamp technique) has any effect on microleakage of direct restorations in occlusal cavities. Materials and Methods One hundred extracted human molars were restored using five restoration techniques (Packable Bulk technique, Occlusal Stamp technique, Successive Cusp Build‐up technique, Successive Cusp Build‐up technique + Brush adaptation, Successive Cusp Build‐up technique + brush adaptation + Dental Operative Microscope magnification). The teeth were subjected to thermal aging for 800 cycles at 5°C and 55°C, infiltrated with basic fuchsin dye for 24 h, and then sectioned buccolingually in the middle of the crown. Infiltration was measured in four areas of the tooth section by five different observers and then given a score from 1 to 3, proportional to infiltration depth. Results The lowest mean scores for infiltration (meaning less infiltration observed) were present in Group A (1.41 ± 0.878) and Group C (1.46 ± 0.679), while Group D showed the highest infiltration scores (1.75 ± 0.853). When comparing the groups for differences, no statistically significant difference in infiltration was found between any technique p

Objectives: Microleakage in direct dental restorations is a primary causal factor in the restoration's failure. The aim of this study was to evaluate whether the technique for occlusal layering of the composite resin (the use of brush adaptation, the use of magnification, cusp build‐up, stamp technique) has any effect on microleakage of direct restorations in occlusal cavities. Materials and Methods: One hundred extracted human molars were restored using five restoration techniques (Packable Bulk technique, Occlusal Stamp technique, Successive Cusp Build‐up technique, Successive Cusp Build‐up technique + Brush adaptation, Successive Cusp Build‐up technique + brush adaptation + Dental Operative Microscope magnification). The teeth were subjected to thermal aging for 800 cycles at 5°C and 55°C, infiltrated with basic fuchsin dye for 24 h, and then sectioned buccolingually in the middle of the crown. Infiltration was measured in four areas of the tooth section by five different observers and then given a score from 1 to 3, proportional to infiltration depth. Results: The lowest mean scores for infiltration (meaning less infiltration observed) were present in Group A (1.41 ± 0.878) and Group C (1.46 ± 0.679), while Group D showed the highest infiltration scores (1.75 ± 0.853). When comparing the groups for differences, no statistically significant difference in infiltration was found between any technique p <.586. Conclusion: The techniques examined for placing the occlusal layer of composite in direct restorations do not differ significantly in terms of marginal infiltration, although a slight improvement was found when using the bulk technique and the successive cusp build‐up. [ABSTRACT FROM AUTHOR]

The aim was to investigate the fatigue performance of endodontically treated (ET) molars restored by various dentin-replacing materials and material configurations. Moreover, the impact of additional adhesive treatment with glass-ionomer cement (GIC) was evaluated. 250 intact molars were collected and randomly distributed into ten groups (n = 25). After endodontic procedure standard Class I cavities were prepared and restored with different direct restorative techniques and dentin-replacing materials. Two-group were restored with either packable or flowable short fiber-reinforced composites (SFRCs). Two-group were restored by experimental fiber-reinforced GIC with and without adhesive treatment. Four-group were restored by conventional and resin-modified GICs with or without adhesive treatment. One-group was restored with a dual-cure composite resin and last group was restored with only conventional composite resin (control). Fatigue-survival was measured for all specimens using a cyclic-loading machine until fracture occurred or a number of 40.000 cycles were achieved. Kaplan-Meyer survival analysis was conducted, followed by pairwise log-rank post hoc comparisons. Fracture mode was then examined by means of optical microscopy and SEM. Group restored with flowable SFRC showed significantly higher survival (p < 0.05) compared to all of the groups, except for group restored with packable SFRC (p > 0.05). Group restored with fiber-reinforced GIC had significantly (p < 0.05) higher survival rates compared to other commercial GICs. SEM demonstrated change of the fracture line when fracture reached the SFRC layer. Direct restoration of Class I in ET molars with the use of SFRCs as dentin-replacing materials demonstrated its ability to reinforce the dental structures and to increase the fatigue resistance in this specific clinical situation. [ABSTRACT FROM AUTHOR]