Search

Typically, organic light‐emitting diodes (OLEDs) are characterized only in steady‐state to determine and optimize their efficiency. Adding further electro‐optical measurement techniques in frequency and time domain helps to quantify charge carrier dynamics and provides deeper insight into the device physics. Combining experimental characterization with electro‐optical device simulation allows one to determine specific material parameters such as the charge carrier mobilities of the layers. Moreover, the obtained device model enables a better understanding of the limitations and degradation pathways of the specific OLED device.

A combined experimental and simulation study on a set of 4 OLEDs with 2 systematically varied guest dopants in the emission layer is presented. A numerical electro-optical model is employed, demonstrating one consistent parameter set that describes both steady-state and ac characteristics of all devices. The model accounts for charge transport and trapping, polar layers, and excitonic loss processes inducing an efficiency rolloff that can be correlated with the shape of the emission zone and the guest dopant concentrations. Furthermore, starting from the resulting parameter set, we show routes for optimized devices with a reduced roll-off.

Encapsulated organic solar cells often show a burn-in behaviour under illumination. This burn-in manifests itself as a rapid performance loss followed by a much slower progression of the degradation. Here we investigate the burn-in for PCDTBT:PC70BM solar cells under a wide range of illumination intensities. We find that increasing the sunlight concentration from 1 Sun to up to 100 Suns does not change the degradation behaviour, i.e. the dependence of all principal photovoltaic parameters on the dose of solar exposure (in Sun hours). This suggests that the degradation mechanisms under solar concentration (≤100 Suns) are the same as those observed under 1 Sun. This result makes it possible to use concentrated sunlight for accelerated stability assessment of these devices. We also find that devices with PEDOT:PSS as hole transport material show a rapid drop in open-circuit voltage of around 100 mV during the first Sun hour of light exposure. By replacing PEDOT:PSS with MoO3 this initial process can be prevented and only the much slower part of the photo-degradation takes place.

We report a cooperative study conducted between different laboratories to investigate organic solar cell degradation with respect to P3HT material properties and different solar cell architectures. Various batches of P3HT were collected from different suppliers reflecting commercial availability as well as properties variability. Among the materials properties explicitly considered were the molar mass, dispersity, regio-regularity, impurities by trace metals and intrinsic doping evaluated from radical concentrations. Each of the participating laboratories contributing test devices applied their own layer stack, i.e. their own device architecture and layout. This variation was appreciated as another parameter for evaluation. Even though a large amount of devices failed due to extrinsic degradation effects, indeed, some materials properties were found to be more important than others for obtaining long lifetimes and high stability of P3HT-based polymer solar cells.

If not oriented perfectly isotropically, the strong dipole moment of polar organic semiconductor materials such as tris-(8-hydroxyquinolate)aluminum (Alq3) will lead to the buildup of a giant surface potential (GSP) and thus to a macroscopic dielectric polarization of the organic film. Despite this having been a known fact for years, the implications of such high potentials within an organic layer stack have only been studied recently. In this work, the influence of the GSP on hole injection into organic layers is investigated. Therefore, we apply a concept called dipolar doping to devices consisting of the prototypical organic materials N,N′-Di(1-naphthyl)-N,N′-diphenyl-(1,1′-biphenyl)-4,4′-diamine (NPB) as nonpolar host and Alq3 as dipolar dopant with different mixing ratios to tune the GSP. The mixtures are investigated in single-layer monopolar devices as well as bilayer metal/insulator/semiconductor structures. Characterization is done electrically using current-voltage (I-V) characteristics, impedance spectroscopy, and charge extraction by linearly increasing voltage and time of flight, as well as with ultraviolet photoelectron spectroscopy. We find a maximum in device performance for moderate to low doping concentrations of the polar species in the host. The observed behavior can be described on the basis of the Schottky effect for image-force barrier lowering, if the changes in the interface dipole, the carrier mobility, and the GSP induced by dipolar doping are taken into account.

Single‐carrier devices are perfect model systems to extract material parameters for more complex multilayer organic light‐emitting diodes (OLEDs) and to learn about charge transport and injection properties of the device. By combining simulation and measurements in steady‐state and frequency domain, we obtain a set of reliable material parameters which can be used to model the multilayer OLED structure. Moreover, we can also evaluate the contact behavior and conclude that the OLED operation is limited by electron transport.

Typically, organic light-emitting diodes (OLEDs) are characterized only in steady-state to determine and optimize their efficiency. Adding further electro-optical measurement techniques in frequency and time domain helps to analyze charge carrier and exciton dynamics and provides deeper insights into the device physics. We, therefore, first present an overview of frequently used OLED measurement techniques and analytical models. A multilayer OLED with a sky-blue thermally activated delayed fluorescent dopant material is employed in this study without loss of generality. Combining the measurements with a full device simulation allows one to determine specific material parameters such as the charge carrier mobilities of all the layers. The main part of this tutorial focuses on how to systematically fit the measured OLED characteristics with microscopic device simulations based on a charge drift-diffusion and exciton migration model in 1D. Finally, we analyze the correlation and sensitivity of the determined material parameters and use the obtained device model to understand limitations of the specific OLED device.

​This document is the Accepted Manuscript version of a Published Work that appeared in final form in ACS Applied Materials & Interfaces, copyright © American Chemical Society after peer review and technical editing by the publisher. To access the final edited and published work see https://pubs.acs.org/doi/10.1021/acsami.9b04991, A variety of experiments on vacuum-deposited methylammonium lead iodide perovskite solar cells are presented, including JV curves with different scan rates, light intensity-dependent open-circuit voltage, impedance spectra, intensity-modulated photocurrent spectra, transient photocurrents, and transient voltage step responses. All these experimental data sets are successfully reproduced by a charge drift-diffusion simulation model incorporating mobile ions and charge traps using a single set of parameters. While previous modeling studies focused on a single experimental technique, we combine steady-state, transient, and frequency-domain simulations and measurements. Our study is an important step toward quantitative simulation of perovskite solar cells, leading to a deeper understanding of the physical effects in these materials. The analysis of the transient current upon voltage turn-on in the dark reveals that the charge injection properties of the interfaces are triggered by the accumulation of mobile ionic defects. We show that the current rise of voltage step experiments allow for conclusions about the recombination at the interface. Whether one or two mobile ionic species are used in the model has only a minor influence on the observed effects. A delayed current rise observed upon reversing the bias from +3 to -3 V in the dark cannot be reproduced yet by our drift-diffusion model. We speculate that a reversible chemical reaction of mobile ions with the contact material may be the cause of this effect, thus requiring a future model extension. A parameter variation is performed in order to understand the performance-limiting factors of the device under investigation.

Single-carrier devices are an excellent model system to study charge injection and charge transport properties of (doped) transport layers and to draw conclusions about organic electronics devices in which they are used. By combining steady-state and impedance measurements at varying temperatures of hole-only devices with different intrinsic layer thicknesses, we are able to determine all relevant material parameters, such as the charge mobility and the injection barrier. Furthermore, the correlation and sensitivity analyses reveal that the proposed approach to study these devices is especially well suited to extract the effective doping density, a parameter which cannot be easily determined otherwise. The effective doping density is crucial in organic light-emitting diodes (OLEDs) for realizing efficient injection, charge balance, and lateral conductivity in display or lighting applications. With the fitted drift-diffusion device model, we are further able to explain the extraordinary two-plateau capacitance-frequency curve of these hole-only devices, which originates from charges that flow into the intrinsic layer at zero applied offset voltage. We demonstrate that the observation of this behaviour is a direct indication for ideal charge injection properties and the observed capacitance-frequency feature is linked to the charge carrier mobility in the intrinsic layer. The extracted material parameters may directly be used to simulate and optimize full OLED devices employing the investigated hole-injection and -transport materials.

Article 1800474, Appreciable progress has been achieved in the development of organic photovoltaics (OPV) over the last decade. However, further improvement of operational stability remains a challenge. In this contribution, focus is placed on corrosion and delamination of the metal contact, which are mainly caused by oxygen or water vapor ingress but in other cases also via mechanical wear and different thermal expansion coefficients. So‐called pinholes and electrode edges provide pathways for ingress of water vapor and oxygen, which may attack the metal–organic interface. Thus, electrical insolation via formation of insulating metal oxide and concomitant mechanical delamination occurs. As charge injection and extraction is suppressed at insulated and delaminated areas, the active area contributing to power conversion gets reduced. This work links analytical and numerical predictions about the active area in contact with the electrode to experimentally observe dependencies. Spatially and time‐resolved electroluminescence measurements provide information on location, size, and growth‐rate of insulated areas. Area loss rates for dark spots depend either sub‐linear (for early stages and edge‐ingress) or linear (later stages) on time. The initial defect size has a clear impact on growth rates. Furthermore, it has possible to demonstrate titanium oxide interlayers to slow down this type of extrinsic degradation.

Erworben im Rahmen der Schweizer Nationallizenzen (http://www.nationallizenzen.ch), This work is part of the interlaboratory collaboration to study the stability of organic solar cells containing PCDTBT polymer as a donor material. The varieties of the OPV devices with different device architectures, electrode materials, encapsulation, and device dimensions were prepared by seven research laboratories. Sets of identical devices were aged according to four different protocols: shelf lifetime, laboratory weathering under simulated illumination at ambient temperature, laboratory weathering under simulated illumination, and elevated temperature (65°C) and daylight outdoor weathering under sunlight. The results generated in this study allow us to outline several general conclusions related to PCDTBT-based bulk heterojunction (BHJ) solar cells. The results herein reported can be considered as practical guidance for the realization of stabilization approaches in BHJ solar cells containing PCDTBT.

We present an overview of opto-electronic characterization techniques for solar cells including light-induced charge extraction by linearly increasing voltage, impedance spectroscopy, transient photovoltage, charge extraction and more. Guidelines for the interpretation of experimental results are derived based on charge drift-diffusion simulations of solar cells with common performance limitations. It is investigated how nonidealities like charge injection barriers, traps and low mobilities among others manifest themselves in each of the studied cell characterization techniques. Moreover, comprehensive parameter extraction for an organic bulk-heterojunction solar cell comprising PCDTBT:PC70BM is demonstrated. The simulations reproduce measured results of 9 different experimental techniques. Parameter correlation is minimized due to the combination of various techniques. Thereby a route to comprehensive and accurate parameter extraction is identified.

ncapsulated organic solar cells often show a burn-in behaviour under illumination. This burn-in manifests itself as a rapid performance loss followed by a much slower progression of the degradation. Here we investigate the burn-in for PCDTBT:PC 70 BM solar cells under a wide range of illumination intensities. We find that increasing the sunlight concentration from 1 Sun to up to 100 Suns does not change the degradation behaviour, i.e. the dependence of all principal photovoltaic parameters on the dose of solar exposure (in Sun hours). This suggests that the degradation mechanisms under solar concentration (≤100 Suns) are the same as those observed under 1 Sun. This result makes it possible to use concentrated sunlight for accelerated stability assessment of these devices. We also find that devices with PEDOT:PSS as hole transport material show a rapid drop in open-circuit voltage of around 100 mV during the first Sun hour of light exposure. By replacing PEDOT:PSS with MoO 3 this initial process can be prevented and only the much slower part of the photo-degradation takes place., Publicerad i Hanssons doktorsavhandling Materials and Device Engineering for Efficient and Stable Polymer Solar Cells som manuskript med titeln: "The role of the hole transport layer in the initial photo-degradation of PCDTBTPC70BM solar cells"

We report a cooperative study conducted between different laboratories to investigate organic solar cell degradation with respect to P3HT material properties and different solar cell architectures. Various batches of P3HT were collected from different suppliers reflecting commercial availability as well as properties variability. Among the materials properties explicitly considered were the molar mass, dispersity, regio-regularity, impurities by trace metals and intrinsic doping evaluated from radical concentrations. Each of the participating laboratories contributing test devices applied their own layer stack, i.e. their own device architecture and layout. This variation was appreciated as another parameter for evaluation. Even though a large amount of devices failed due to extrinsic degradation effects, indeed, some materials properties were found to be more important than others for obtaining long lifetimes and high stability of P3HT-based polymer solar cells.

A variety of experiments on vacuum-deposited methylammonium lead iodide perovskite solar cells are presented, including JV curves with different scan rates, light intensity-dependent open-circuit voltage, impedance spectra, intensity-modulated photocurrent spectra, transient photocurrents, and transient voltage step responses. All these experimental data sets are successfully reproduced by a charge drift-diffusion simulation model incorporating mobile ions and charge traps using a single set of parameters. While previous modeling studies focused on a single experimental technique, we combine steady-state, transient, and frequency-domain simulations and measurements. Our study is an important step toward quantitative simulation of perovskite solar cells, leading to a deeper understanding of the physical effects in these materials. The analysis of the transient current upon voltage turn-on in the dark reveals that the charge injection properties of the interfaces are triggered by the accumulation of mobile ionic defects. We show that the current rise of voltage step experiments allow for conclusions about the recombination at the interface. Whether one or two mobile ionic species are used in the model has only a minor influence on the observed effects. A delayed current rise observed upon reversing the bias from +3 to -3 V in the dark cannot be reproduced yet by our drift-diffusion model. We speculate that a reversible chemical reaction of mobile ions with the contact material may be the cause of this effect, thus requiring a future model extension. A parameter variation is performed in order to understand the performance-limiting factors of the device under investigation.