Search

While dental composite long-term aging has already been studied in the past, no data exist about the early aging while it might be detrimental regarding the composites' longevity. This study aims to better understand the effects of early water exposure on dental composites. Dental resin composites with different fillers ratio were subjected to water exposure during 24 h, 1 week, or 1 month. After photopolymerization, the samples were stored at different conditions, whether in wet or dry condition (W, D, respectively) and in wet conditions after a first 24 h storage in dry conditions (DW). Three-point bending tests were performed to measure the flexural modulus. The samples were then subjected to a sorption/desorption protocol. While the matrix alone did not undergo any mechanical degradation with exposure time, the composites matrices presented a decrease in elastic modulus. This decrease was the highest for the matrix with nonsilanized fillers. Interestingly, the DW condition was detrimental for all the samples. Regarding the sample with nonsilanized fillers in DW for 1 month presented an elastic modulus lower than the matrix alone. These results were assigned to the sorption capacity of the polymer matrix, suggesting that the diffusion mechanisms and the nature of water molecules are determinant in the composite degradation. This study showed that dental composite early degradation mechanisms after water exposure are involved in the polymer matrix postpolymerization process as soon as after 24 h. Such mechanisms are detrimental in terms of the dental composite efficiency and have to be understood.

Objective Thermocycling is widely used to age dental composites but with very different results from one study to another, even with apparent similar conditions. This study aims at understanding better the relative damaging speed of matrix and fillers, based on theoretical models. Methods Eight formulations of an experimental dental material were produced. The same organic matrix was used and silanated barium glass particles were added as fillers with different filler ratios. Samples were thermocycled up to 10 000 cycles. Three-point bending tests were carried out at different steps. The yield stress was measured among other mechanical properties. Results Composite properties were degraded by thermocycling. The decrease was slight during the first 5 000 cycles whereas it decreased significantly after 10 000 cycles. The Turcsanyi model asserts that the interface yield stress is slightly affected in the first 5 000 cycles and then falls down, while the decrease of matrix yield stress is linear. Significance Each component of a composite does not age at the same rate. First, the matrix acts as a protector until the water finds its way to the interphase. The filler silanization treatment is highly sensitive to hydrolysis and is damaged rapidly from that moment. Numerical simulations and surface observations confirmed that cracks appear to propagate in the neighbourhood of the interface but not directly within it.

Dental decays are one of the most widespread surgeries over the world. But half of the operation’s deals with the repair of a former restoration instead of curing an original decay. To reduce this ...

A composite dental restoration is facing an aggressive environment which may damage the material in vivo. Water thermocycling is frequently used to simulate the ageing of a composite, but its effec...

Objective A costly advantageous approach in composites development process is to limit experimental tests by predicting mechanical properties with respect to their filler ratio. Models exist for other fields than dentistry. They have been compared to 3-point bending test experimental results for yield stress, flexural modulus and flexural strength. Methods Five formulations of the same experimental material were made. They were composed of an organic matrix and different ratios of silanated barium glass particles. The samples were stored in distilled water for 24 h at 37 °C prior to the 3-point bending test. The Turcsanyi model for yield stress was notably investigated, and SEM was used to complete data analysis. Results The yield stress showed reproducible results and a good fit with Turcsanyi model with respect to filler ratio. The flexural modulus data are not scattered but did not fit with the existing models. No trend could emerge for flexural strength and strain because of scattering; these properties are more unpredictable. The SEM observations of fracture areas confirm a good matrix-filler interface quality. Significance SEM pictures validated the numerical parameter obtained from Turcsanyi model. The latter therefore seems to be applicable to dental composites. Firstly, it enables to predict the evolution of the material yield stress without testing all filler ratios. Secondly, this model provides a good way to get micro-information on the matrix-filler interface from macroscopic tests. The discrepancy between flexural modulus results and theory highlighted the necessity to include an “interface quality” parameter in accurate predictive models.