Search

This study attempts to derive the uncertainty of the soil moisture estimation from passive microwave satellite mission at global scale. To do so, the approach is based on the sensitivity of the Soil Moisture and Ocean Salinity (SMOS) soil moisture retrieval quality to the land surface characteristics within its footprint (presence of forest, topography, open water bodies, sand, clay, bulk density and soil organic carbon content). First, we performed a global assessment of SMOS using in situ measurements from the International Soil Moisture Network (ISMN) as reference, with more than 1900 ISMN stations and 10 years of SMOS data. This assessment shows that the ubRMSD scores vary greatly between locations (with a mean of 0.074 m3m−3 and an interquartile range of 0.030 m3m−3). Second, the scores are analyzed for different surface conditions within the satellite footprint. The best agreement between the ground measurement and SMOS time series are obtained for low forest cover, low topographic complexity, and marginal presence of open water bodies within the SMOS footprint. Soil parameters also have an impact, with better scores for sandier soils with a high bulk-density and low soil organic carbon content. Finally, we propose to extrapolate the obtained relationships, using a multiple linear regression, in order to derive a global map of SMOS uncertainties based on surface conditions. This map of predicted uncertainties show a diverse range of ubRMSD values across the globe (with a mean of 0.076 m3m−3 and an interquartile range of 0.031 m3m−3) depending on the surface characteristics. At the ISMN site location, the predicted ubRMSD shows similar results than the comparison between SMOS and the in situ measurements. The map of predicted SMOS ubRMSD represents an upper bound estimate of the SMOS uncertainty, as it includes the uncertainties of the in situ sensor measurements and the scale mismatch. Further investigations will focus on the different components of this uncertainty budget to obtain a better assessment of the absolute uncertainties of SMOS soil moisture retrievals across the globe.

Biodegradable blends based on plasticized poly(lactic acid) PLA and thermoplastic starch (TPS) have been obtained. The influence of the PLA plasticizer as a compatibility agent has been studied by using two different plasticizers such as neat oligomeric lactic acid (OLA) and functionalized with maleic acid (mOLA). In particular, the morphological, thermal, and mechanical properties have been studied as well as the shape memory ability of the melt-processed materials. Therefore, the influence of the interaction between different plasticizers and the PLA matrix as well as the compatibility between the two polymeric phases on the thermally-activated shape memory properties have been studied. It is very interesting to use the same additive able to act as both plasticizer and compatibilizer, decreasing the glass transition temperature of PLA to a temperature close to the physiological one, obtaining a material suitable for potential biomedical applications. In particular, we obtain that OLA-plasticized blend (oPLA/TPS) show very good thermally-activated capability at 45 °C and 50% deformation, while the blend obtained by using maleic OLA (moPLA/TPS) did not show shape memory behavior at 45 °C and 50% deformation. This fact is due to their morphological changes and the loss of two well-distinguished phases, one acting as fixed phase and the other one acting as switching phase to typically obtain shape memory response. Therefore, the thermally-activated shape memory results show that it is very important to make a balance between plasticizer and compatibilizer, considering the need of two well-established phases to obtain shape memory response.

Despite their popularity and multiplicity of applications, wood–polymer composites (WPCs) still have to overcome particular issues related to their processing and properties. The main aspect is the compatibility with plant-based materials which affects the overall performance of the material. It can be enhanced by strengthening the interfacial adhesion resulting from physical and/or chemical interactions between the matrix and filler, which requires introducing a compatibilizer or a proper modification of one or both phases. Herein, the impact of cellulose filler modifications with varying contents (1–10 wt%) of hexamethylene diisocyanate (HDI) on the compatibility of Mater-Bi/poly(ε-caprolactone) (PCL)-based biocomposites was evaluated. An analysis of surface wettability revealed that the filler modification reduced the hydrophilicity gap between phases, suggesting compatibility enhancement. It was later confirmed via microscopic observation (scanning electron microscopy (SEM) and atomic force microscopy (AFM)), which pointed to the finer dispersion of modified particles and enhanced quality of the interface. The rheological analysis confirmed increased system homogeneity by the reduction in complex viscosity. In contrast, thermogravimetric analysis (TGA) indicated the efficient modification of filler and the presence of the chemical interactions at the interface by the shift of thermal decomposition onset and the changes in the degradation course.

Unsaturated polyester resin (UPR) is one of the first commercialized polymer matrices for composites reinforced with glass fibers, but has remained popular to this day. To reduce their environmental impact, natural fibers have been used as reinforcements. Researchers all over the world are still interested in these composites, and numerous papers have been published in the last four decades. Using bibliometric analysis, this work provides compiled, structured, and relevant information about the evolution and current state of these materials. This first study on UPR biocomposites based on bibliometric analysis examined 531 published papers identified in the Scopus database from 1982 to July 2022. An analysis of the most active states, leading institutions, and leading authors is followed by the identification of key areas such as the most common natural fibers used as reinforcements, fiber treatments, and composite design parameters such as processing techniques; recently, composite testing; and technological applications. The findings emphasize the importance of staying active in this global field and provide information on novel promising topics for future research.

Stereolithography (SL) stands out as a relatively fast additive manufacturing method to produce thermoset components with high resolutions. The majority of SL resins consist of acrylate monomers which result in materials with curing-induced shrinkage problems and this, in addition to the incomplete and non-uniform conversions reached in the SL process, results in poor mechanical properties. To address this issue, a dual-curing formulation was developed by mixing an epoxy monomer into a commercial multi-acrylate SL resin: the first curing stage is acrylate free-radical photopolymerization at ambient temperature, and the second curing stage is cationic epoxy homopolymerization at higher temperatures. The fully dual-cured materials are macroscopically homogeneous, with nanoscale domains observed by Atomic Force Microscopy (AFM), and with unimodal tan delta peaks observed in Dynamic Mechanical Analysis (DMA). The uncured material was storage stable at ambient conditions for at least 9 weeks since the epoxy part was virtually unreactive at these temperatures. With the dual-cured materials, a nearly 10-fold increase in Young’s modulus was achieved over the neat acrylate resin. At the thermal curing stage, the presence of diperoxyketal thermal radical initiator to the liquid formulation facilitated the polymerization of unreacted acrylates that remained from the SL process simultaneously with epoxy homopolymerization and helped the material attain improved properties.

A biobased diglycidyl ether of vanillin (DGEVA) epoxy resin was nanostructured by poly(ethylene oxide-b-propylene oxide-b-ethylene oxide) (PEO-PPO-PEO) triblock copolymer. Due to the miscibility/immiscibility properties of the triblock copolymer in DGEVA resin, different morphologies were obtained depending on the triblock copolymer amount. A hexagonally packed cylinder morphology was kept until reaching 30 wt% of PEO-PPO-PEO content, while a more complex three-phase morphology was obtained for 50 wt%, in which large worm-like PPO domains appear surrounded by two different phases, one of them rich in PEO and another phase rich in cured DGEVA. UV-vis measurements show that the transmittance is reduced with the increase in triblock copolymer content, especially at 50 wt%, probably due to the presence of PEO crystals detected by calorimetry.

In this work, GTR/thermoplastics blends (in ratio 50/50 and 75/25 wt.%) were prepared by melt-compounding in an internal mixer. During research, trans-polyoctenamer rubber (TOR), ethylene-vinyl acetate copolymer (EVA), ethylene-octene copolymer (EOC), and linear low-density polyethylene (LLDPE), were used in their thermoplastic phase. Microstructure and processing-performance property interrelationships of the studied materials were investigated by: atomic force microscopy (AFM), scanning electron microscopy (SEM), rubber process analyzer (RPA), Mooney viscometer, plastometer, gas chromatography with mass spectrometry, differential scanning calorimetry (DSC), tensile tests and swelling behavior. In blends of thermoplastics with a high content of GTR (50 and 75 wt.%), the thermoplastic modifier type had a significant impact on the processing behavior and microstructure of blends. In terms of the physico-mechanical properties, the GTR/thermoplastics ratio affected elongation at break, hardness, and density, while its effect on tensile strength was negligible. DSC analysis showed that thermoplastics, as modifiers of GTR, should be considered as binders and not plasticizers, as reflected in the almost constant glass-transition temperature of the blends. RPA measurements indicated higher values of G* and η* for GTR-rich blends. SEM showed a rubber-like interfacial break, while AFM confirmed interfacial contact between GTR and thermoplastics.

Impairments of the ulnar nerve in the courses of supracondylar fractures of the humerus (SCHF) are one of the most common complications after elbow fractures in children. A 6-years-old girl presented to the Emergency Department with the complaint of pain and reduced range of motion of the left elbow after fell on the flexed elbow. The diagnosis was supracondylar fractures of the left humerus. The patient had symptoms of paresis of the ulnar nerve after treated by closed reduction with using K-wires and immobilization in an over-elbow plaster cast. The decision to “watch and wait” was made taking into account clinical condition, findings in additional examinations, especially US. Ultrasound examinations helped to avoid unnecessary surgical treatment. After around ten months, complete resolution of symptoms was achieved. The patient recovered well.

Reactive extrusion is a cost-effective and environmentally-friendly method to produce new materials with enhanced performance properties. At present, reactive extrusion allows in-situ polymerization, modification/functionalization of polymers or chemical bonding of two (or more) immiscible phases, which can be carried out on commonly used extrusion lines. Although reactive extrusion has been known for many years, its application for processing of bio-based polymer blends and composites is a relatively new direction of scientific research. This work presents a literature review on recent advances in the processing of bio-based polymer blends and composites via reactive extrusion. We described compatibilization mechanisms for different types of biodegradable polymeric materials based on: (i) aliphatic polyesters, (ii) aliphatic polyesters/starch and (iii) aliphatic polyester/natural rubber systems. A special attention was focused on conventional and dynamic cross-linking of bio-based polymer blends and composites as an effective way to prepare new materials with unique properties e.g. biodegradable thermoplastic elastomers or shape-memory materials. Advantages and limitations affecting future trends in development of biodegradable polymer blends and composites reactive extrusion are also discussed.

Surface morphology development for SBM triblock copolymer thin films has been studied by atomic force microscopy. The effect of copolymer composition and solvent on the final morphology has been investigated. Obtained results indicated that depending on the block ratio (symmetric or asymmetric with minority middle block) and solvent, lamellar, hexagonal, cylindrical, or spheres in lamellae (/s)-type morphologies can be achieved at film surfaces. The influence of the interaction parameters among blocks and solvents and cohesive energy values of block pairs on the final morphology has been proved., INTRODUCTION Among the applications of di- or triblock copolymers based on polystyrene and elastomeric blocks, their use for preparing solvent-based highly elastic coatings that provide outstanding crack-free adhesion to polar [...]

Versatile acrylate–epoxy hybrid formulations are becoming widespread in photo/thermal dual-processing scenarios, especially in 3D printing applications. Usually, parts are printed in a stereolithography or digital light processing (DLP) 3D printer, after which a thermal treatment would bestow the final material with superior mechanical properties. We report the successful formulation of such a hybrid system, consisting of a commercial 3D printing acrylate resin modified by an epoxy–anhydride mixture. In the final polymeric network, we observed segregation of an epoxy-rich phase as nano-domains, similar to what was observed in a previous work. However, in the current work, we show the effectiveness of a coupling agent added to the formulation to mitigate this segregation for when such phase separation is undesired. The hybrid materials showed significant improvement of Young’s modulus over the neat acrylate. Once the flexible, partially-cured material was printed with a minimal number of layers, it could be molded into a complex form and thermally cured. Temporary shapes were readily programmable on this final material, with easy shape recovery under mild temperatures. Inspired by repairable 3D printed materials described recently, we manufactured a large object by printing its two halves, and then joined them covalently at the thermal cure stage with an apparently seamless union.

Reactive blending is a promising approach for the sustainable development of bio-based polymer blends and composites, which currently is gaining more and more attention. In this paper, biodegradable blends based on poly(ε-caprolactone) (PCL) and poly(lactic acid) (PLA) were prepared via reactive blending performed in an internal mixer. The PCL and PLA content varied in a ratio of 70/30 and 55/45. Reactive modification of PCL/PLA via liquid organic peroxides (OP) including 0.5 wt.% of tert-butyl cumyl peroxide (BU), 2,5-dimethyl-2,5-di-(tert-butylperoxy)-hexane (HX), and tert-butyl peroxybenzoate (PB) is reported. The materials were characterized by rotational rheometer, atomic force microscopy (AFM), thermogravimetry (TGA), differential scanning calorimetry (DSC), tensile tests and biodegradability tests. It was found that the application of peroxides improves the miscibility between PCL and PLA resulted in enhanced mechanical properties and more uniform morphology. Moreover, it was observed that the biodegradation rate of PCL/PLA blends reactively compatibilized was lower comparing to unmodified samples and strongly dependent on the blend ratio and peroxide structure. The presented results confirmed that reactive blending supported by organic peroxide is a promising approach for tailoring novel biodegradable polymeric systems with controllable biodegradation rates.

The utilization of forestry waste resources in the production of polyurethane resins is a promising green alternative to the use of unsustainable resources. Liquefaction of wood-based biomass gives polyols with properties depending on the reagents used. In this article, the liquefaction of forestry wastes, including sawdust, in solvents such as glycerol and polyethylene glycol was investigated. The liquefaction process was carried out at temperatures of 120, 150, and 170 °C. The resulting bio-polyols were analyzed for process efficiency, hydroxyl number, water content, viscosity, and structural features using the Fourier transform infrared spectroscopy (FTIR). The optimum liquefaction temperature was 150 °C and the time of 6 h. Comprehensive analysis of polyol properties shows high biomass conversion and hydroxyl number in the range of 238–815 mg KOH/g. This may indicate that bio-polyols may be used as a potential substitute for petrochemical polyols. During polyurethane synthesis, materials with more than 80 wt% of bio-polyol were obtained. The materials were obtained by a one-step method by hot-pressing for 15 min at 100 °C and a pressure of 5 MPa with an NCO:OH ratio of 1:1 and 1.2:1. Dynamical-mechanical analysis (DMA) showed a high modulus of elasticity in the range of 62–839 MPa which depends on the reaction conditions.