Search

A pilot-scale experiment of natural rubber processing wastewater treatment was conducted using a combination system consisting of a two-stage up-flow anaerobic sludge blanket (UASB) and a down-flow hanging sponge (DHS) reactor for more than 10 months. The system achieved a chemical oxygen demand (COD) removal efficiency of 95.7%±1.3% at an organic loading rate of 0.8 kgCOD/(m³.d). Bacterial activity measurement of retained sludge from the UASB showed that sulfate-reducing bacteria (SRB), especially hydrogen-utilizing SRB, possessed high activity compared with methane-producing bacteria (MPB). Conversely, the acetate-utilizing activity of MPB was superior to SRB in the second stage of the reactor. The two-stage UASB–DHS system can reduce power consumption by 95% and excess sludge by 98%. In addition, it is possible to prevent emissions of greenhouse gases (GHG), such as methane, using this system. Furthermore, recovered methane from the two-stage UASB can completely cover the electricity needs for the operation of the two-stage UASB–DHS system, accounting for approximately 15% of the electricity used in the natural rubber manufacturing process. [ABSTRACT FROM AUTHOR]

In this study, continuous operation of a pilot-scale upflow anaerobic sludge blanket (UASB) reactor for sewage treatment was conducted for 630 days to investigate the physical and microbial characteristics of the retained sludge. The UASB reactor with a working volume of 20.2 m³ was operated at ambient temperature (16-29 °C) and seeded with digested sludge. After 180 days of operation, when the sewage temperature had dropped to 20 °C or lower, the removal efficiency of both total suspended solids (TSS) and total biochemical oxygen demand (BOD) deteriorated due to washout of retained sludge. At low temperature, the cellulose concentration of the UASB sludge increased owing to the rate limitation of the hydrolytic reaction of suspended solids in the sewage. However, after an improvement in sludge retention (settleability and concentration) in the UASB reactor, the process performance stabilized and gave sufficient results (68% of TSS removal, 75% of total BOD removal) at an hydraulic retention time (HRT) of 9.7 h. The methanogenic activity of the retained sludge significantly increased after day 246 due to the accumulation of Methanosaeta and Methanobacterium following the improvement in sludge retention in the UASB reactor. Acid-forming bacteria from phylum Bacteroidetes were detected at high frequency; thus, these bacteria may have an important role in suspended solids degradation. [ABSTRACT FROM AUTHOR]

In this study, a lab scale EGSB reactor was operated for 400 days to investigate the influence of temperature-decrease on the microbial characteristic of retained sludge. The EGSB reactor was started-up at 15°C seeding with 20°C-grown granular sludge. The influent COD of synthetic wastewater was set at 0.6-0.8 gCOD/L. The process-temperature was stepwise reduced from 15°C to 5°C during 400 days operation. Decrease of temperature of the reactor from 15°C to 10°C caused the decline of COD removal efficiency. However, continuous operation of the EGSB reactor led the efficient treatment of wastewater (70% of COD removal, 50% of methane recovery) at 10°C. We confirmed that the both acetate-fed and hydrogen-fed methanogenic activities of retained sludge clearly increased under 15 to 20°C. Changes of microbial profiles of methanogenic bacteria were analyzed by 16S rDNA-targeted DGGE analysis and cloning. It shows that genus Methanospirillum as hydrogen-utilizing methanogen proliferated due to low temperature operation of the reactor. On the other hand, genus Methanosaeta presented in abundance as acetoclastic-methanogen throughout the experiment. [ABSTRACT FROM AUTHOR]

Previously, we found that the newly isolated Clostridium sp. strain JC3 became the dominant cellulose-degrading bacterium in thermophilic methanogenic sludge. In the present study, the behavior of strain JC3 in the thermophilic anaerobic digestion process was investigated quantitatively by molecular biological techniques. A cellulose-degrading experiment was conducted at 55 °C with a 9.5 L of anaerobic baffled reactor having three compartments (Nos. 1, 2, 3). Over 80% of the COD input was converted into methane when 2.5 kgCODm-3d-1 was loaded for an HRT of 27 days. A FISH probe specific for strain JC3 was applied to sludge samples harvested from the baffled reactor. Consequently, the ratio of JC3 cells to DAPI-stained cells increased from below 0.5% (undetectable) to 9.4% (compartment 1), 13.1% (compartment 2) and 21.6% (compartment 3) at day 84 (2.5 kgCODm-3 d-1). The strain JC3 cell numbers determined by FISH correlated closely with the cellulose-degrading methanogenic activities of retained sludge. A specific primer set targeting the cellulase gene (cellobiohydrolaseA: cbhA) of strain JC3 was designed and applied to digested sludge for treating solid waste such as coffee grounds, wastepaper, garbage, cellulose and so on. The strain JC3 cell numbers determined by quantitative PCR correlated closely with the cellulose-sludge loading of the thermophilic digester. Strain JC3 is thus important in the anaerobic hydrolysis of cellulose in thermophilic anaerobic digestion processes. [ABSTRACT FROM AUTHOR]

Whole cell fluorescence in-situ hybridization (FISH) with 16S rRNA targeted oligonucleotides was applied to reveal the microbial ecological structure of UASB-grown granular sludge. The FISH analysis indicated that the members of the domain Archaea accounted for 28 to 53% of the total cells in various granular sludge sources, while Methanosaeta and Methanobacteriaceae cells accounted for 13 to 38%, and 4 to 27%, respectively. Methanosaeta cell density and Methanobacteriaceae cell density were strongly correlated, respectively, with acetate-utilizing methane production activity and with hydrogen-utilizing methane production activity. [ABSTRACT FROM AUTHOR]

This study was designed to evaluate a treatment system for high strength wastewater (vinasse) from a sugarcane molasses-based bio-ethanol plant in Thailand. A laboratory-scale two-phase treatment system composed of a sulfate reducing (SR) tank and multi-staged up-flow anaerobic sludge blanket (MS-UASB) reactor was used as the pre-treatment unit. Conventional UASB and down-flow hanging sponge (DHS) reactors were used as the post-treatment unit. The treatment system was operated for 300 days under ambient temperature conditions (24.6-29.6 °C). The hydraulic retention time (HRT) in each unit was kept at 25 h for the two-phase system and 23 h for the UASB&DHS. The influent concentration was allowed to reach up to 15,000 mg chemical oxygen demand (COD)/L. COD removal efficiency (based on influent COD) of the two-phase MS-UASB and the UASB&DHS was 54.9 and 18.7%, respectively. Due to the effective removal of sulfide in the SR tank, the MS-UASB achieved a high methane conversion ratio of up to 97%. In DHS, nitrification occurred at the outside portion of the sponge media while denitrification occurred at the inside. Consequently, 27% of the total nitrogen (TN) was removed. An amount of 32% of residual nitrogen (28 mgN/L) was in the form of nitrate, a better nitrogen state for fertilizer. [ABSTRACT FROM AUTHOR]

An up-flow anaerobic sludge blanket (UASB) - down-flow hanging sponge (DHS) was applied to Japanese municipal sewage treatment, and its treatability, energy consumption, and sludge production were evaluated. The designed sewage load was 50 m3/d. The sewage typically had a chemical oxygen demand (COD) of 402 mg/L, a suspended solids (SS) content of 167 mg/L, and a temperature of 17-29° C. The UASB and DHS exhibited theoretical hydraulic retention times of 9.7 and 2.5 h, respectively. The entire system was operated without temperature control. Operation was started with mesophilic anaerobic digested sludge for the UASB and various sponge media for the DHS. Continuous operational data suggest that although the cellulose decomposition and methanogenic process in the UASB are temperature sensitive, stable operation can be obtained by maintaining a satisfactory sludge volume index and sludge concentration. For the DHS, the cube-type medium G3-2 offers superior filling rates, biological preservation and operational execution. The SS derived from the DHS contaminated the effluent but could be removed by optional sand filtration. A comparison with conventional activated sludge (CAS) treatment confirmed that this system is adequate for municipal sewage treatment, with an estimated energy requirement and excess sludge production approximately 75 and 85% less than those of CAS, respectively. [ABSTRACT FROM AUTHOR]

The biodegradation characteristics of palm oil mill effluent (POME) and the related microbial community were studied in both actual sequential anaerobic ponds in Malaysia and enrichment cultures. The significant degradation of the POME was observed in the second pond, in which the temperature was 35-37 WC. In this pond, biodegradation of major long chain fatty acids (LCFA), such as palmitic acid (C16:0) and oleic acid (C18:1), was also confirmed. The enrichment culture experiment was conducted with different feeding substrates, i.e. POME, C16:0 and C18:1, at 35 WC. Good recovery of methane indicated biodegradation of feeds in the POME and C16:0 enrichments. The methane production rate of the C18:1 enrichment was slower than other substrates and inhibition of methanogenesis was frequently observed. Denaturing gradient gel electrophoresis (DGGE) analyses indicated the existence of LCFA-degrading bacteria, such as the genus Syntrophus and Syntorophomonas, in all enrichment cultures operated at 35 WC. Anaerobic degradation of the POME under mesophilic conditions was stably processed as compared with thermophilic conditions. [ABSTRACT FROM AUTHOR]

Anaerobic wastewater treatment has been focused on its eco-friendly nature in terms of the improved energy conservation and reduction in carbon dioxide emissions. However, the anaerobic process discharges unrecovered methane as dissolved methane. In this study, to prevent the emission of dissolved methane from up-flow anaerobic sludge blanket (UASB) reactors used to treat sewage and to recover it as useful gas, we employed a two-stage downflow hanging sponge (DHS) reactor as a post-treatment of the UASB reactor. The closed DHS reactor in the first stage was intended for the recovery of dissolved methane from the UASB reactor effluent; the reactor could successfully recover an average of 76.8% of the influent dissolved methane as useful gas (containing methane over 30%) with hydraulic retention time of 2 h. During the experimental period, it was possible to maintain the recovered methane concentrations greater than 30% by adjusting the air supply rate. The remaining dissolved methane after the first stage was treated by the next step. The second closed DHS reactor was operated for oxidation of the residual methane and polishing of the remaining organic carbons. The reactor had a high performance and the influent dissolved methane was mostly eliminated to approximately 0.01mgCODL-1. The dissolved methane from the UASB reactor was completely eliminated—by more than 99%—by the post-treatment after the two-stage closed DHS system. [ABSTRACT FROM AUTHOR]

A 2.0 L volume of EGSB reactor was operated at 208C for more than 500 days with 0.3-0.4 g COD/L of sucrose base wastewater to investigate the influence of effluent-recirculation on the process performance. At the start up period, the reactor was operated in EGSB mode with 5 m/h upflow velocity by continuous effluent recirculation. The COD loading was set to 7.2-9.6 kg COD/m3 day with HRT of 1 hour. However, in this mode, EGSB reactor exhibited insufficient COD removal efficiency, i.e., 50-60%. Therefore, UASB mode (without recirculation, 0.7 m/h upflow velocity) was used for 30 minutes in every 40 minutes cycle to increase the COD concentration in the sludge bed. As a result, an excellent process performance was shown. The COD removal efficiency increased from 65% to 91% and the reactor could maintain a good physical property of retained sludge (sludge concentration: 33.4 g VSS/L and SVI: 25 mL/g VSS). Furthermore, retained sludge possessed sufficient level of methanogenic activity at 208C. [ABSTRACT FROM AUTHOR]

A thermophilic UASB reactor was operated at 55 deg. C for greater than 470 days in order to investigate the effects of feed composition on the changes in microbial community structure where thermophilic granular sludge was used as the inoculum source. The feed compositions were changed with cultivation days; phase 1 (1-70 days), alcohol distillery wastewater; phase 2 (71-281 days), artificial acetate wastewater; phase 3 (282-474 days), artificial sucrose wastewater. During the first one month of each phase, the methanogenic activity and cell density of methanogens quantified by fluorescence in situ hybridization (FISH) drastically changed as a result of shift in feed composition. When artificial acetate wastewater was used as feed, retained granular sludge was partially disintegrated due to a decrease in the number of symbiotic bacterial community members: acetogens (acidogens) and hydrogenotrophic methanogens. In contrast, when the feed was shifted to sucrose (phase 3), granulation of biomass was promoted by a remarkable proliferation of the symbiotic community. The presence of hydrogen-utilizing methanogens and acetogens (acidogens) are shown to be effective for the enhancement of thermophilic granulation. The cell density of methanogens determined by FISH was strongly correlated with the methane-producing potential of the retained thermophilic granular sludge. [ABSTRACT FROM AUTHOR]

A novel methodology is proposed in this study to evaluate the tensile strength of biofilms by using a newly developed tensile test device. Three different types of biofilms were prepared for tensile test: Run 1 biofilm was aerobically cultivated on glucose, and Run 2 and Run3 biofilms were denitrifying biofilms grown on glucose and on methanol, respectively, as a sole carbon source. Each of three biofilms wasformed on the outer surfaces of tygon-made tubes (diameter 4.76 mm) submerged in a rectangular open-channel reactor. The results demonstrated that the tensile strengths of three different biofilms had a tendency to increase with the biofilm development over a period of 50 days of reactor operation and eventually reached a similar range, approximately 500 to 1000 Pa, independent of biofilm types or cultivation conditions. An elastic coefficient of the biofilm was determined by assuming that a biofilm behaves as an elastic material during the tensile test. A strong positive correlation was found between the elasticcoefficient and the tensile strength. However, the behavior of extracellular biopolymer (ECP) content and the biofilm density were not dependent on the tensile strength. Scanning electron microscope (SEM) observations also suggested that the biofilm structural properties such as elastic coefficient are more determinative factors for the tensile strength than are the biofilm physiological properties such as ECPcontent. [ABSTRACT FROM AUTHOR]

After seeded with mesophilically-grown (35 deg. C) granular sludge, a laboratory-scale UASB reactor was thermophilically (55 deg. C) operated over 8 months by feeding with an alcohol distillery wastewater. Use of mesophilically-grown granules as a seed material proved to be more advantageous for rapid and stable start-up of thermophilic UASB process, compared with the use of suspended-growth sludge taken from a thermophilic anaerobic digester. The reactor accommodated successfully a COD loading 30 kgCOD7m-37d-1, with a COD removal efficiency of 85%. However, during a period of 30 kgCOD7m-37d-1, propionate accumulated in the effluent up to 300-600 mgCOD7l-1. Thermophilic cultivation caused a drastic increase of methanogenic activities (55 deg. C) of the retained sludge: 4.4 times for acetate, 4.6 times for propionate, and 3.5 times for hydrogen as large as those of the seed sludge. A considerably low value of propionate-fed methanogenic activity, i.e. only 1/5 of acetate-fed activity and only 1/23 of hydrogen-fed activity, suggested that the propionate degradation is subject to be a rate-limiting stepin thermophilic anaerobic processes. [ABSTRACT FROM AUTHOR]