Search

Fibre metal laminates (FML) are the modern hybrid materials with potential wide range of applications in aerospace technology due to their excellent mechanical properties (particularly fatigue strength, resistance to impacts) and also excellent corrosion resistance. The study describes the resistance to low velocity impacts in Ti/CFRP laminates. Tested laminates were produced in autoclave process. The laminates were characterized in terms of their response to impacts in specified energy range (5J, 10J, 20J). The tests were performed in accordance with ASTM D7137 standard. The laminates were subjected to impacts by means of hemispherical impactor with diameter of 12,7 mm. The following values have been determined: impact force vs. time, maximum force and the force at which the material destruction process commences (Pi). It has been found that fibre titanium laminates are characterized by high resistance to impacts. This feature is associated with elasto-plastic properties of metal and high rigidity of epoxy - fibre composite. It has been observed that Ti/CFRP laminates are characterized by more instable force during impact in stage of stabilization of impactor-laminate system and stage of force growth that glass fibre laminates. It has been observed more stable force decrease in stage of stress relaxation and withdrawal of the impactor. In energy range under test, the laminates based on titanium with glass and carbon fibres reinforcement demonstrate similar and high resistance to low-velocity impact, measured by means of failure initiation force and impact maximum force.

The objective of this study was to compare the effects of using short and continuous fibres for repairing compression-induced tooth crown damage. Human teeth were used for the study. They were upper medial incisors and maxillary first premolars lost due to periodontal causes. The teeth were divided into two groups with Hahnenkratt and short glass fibres. Teeth compressive strength tests were carried out. Then micro-CT imaging of the teeth and their fractures obtained after compression was performed. The teeth restored with Hahnenkratt's glass fibre posts showed higher compressive strength than the teeth restored using the EverX Posterior material. The tooth's most weakened and sensitive point after endodontic treatment was the cervical area of the tooth. All cracks were parallel to the root canal., (© 2023. The Author(s).)

Probiotics seem to have promising effects in the prevention and treatment of allergic conditions including atopic dermatitis (AD) and food allergy. The purpose of this multicenter randomized placebo-controlled trial was to evaluate the effectiveness of a probiotic preparation comprising Lactobacillus rhamnosus ŁOCK 0900, Lactobacillus rhamnosus ŁOCK 0908, and Lactobacillus casei ŁOCK 0918 in children under 2 years of age with AD and a cow's milk protein (CMP) allergy. The study enrolled 151 children, who-apart from being treated with a CMP elimination diet-were randomized to receive the probiotic preparation at a daily dose of 10 9 bacteria or a placebo for three months, with a subsequent nine-month follow-up. The primary outcomes included changes in AD symptom severity assessed with the scoring AD (SCORAD) index and in the proportion of children with symptom improvement (a SCORAD score decreased by at least 30% in comparison with that at baseline). After the three-month intervention, both the probiotic and placebo groups showed a significant ( p < 0.0001) decrease in SCORAD scores, which was maintained nine months later. The percentage of children who showed improvement was significantly higher in the probiotic than in the placebo group (odds ratio (OR) 2.56; 95% confidence interval (CI) 1.13-5.8; p = 0.012) after three months. Probiotics induced SCORAD improvement mainly in allergen sensitized patients (OR 6.03; 95% CI 1.85-19.67, p = 0.001), but this positive effect was not observed after nine months. The results showed that the mixture of probiotic ŁOCK strains offers benefits for children with AD and CMP allergy. Further research is necessary to assess the effect of probiotic supplementation on the development of immune tolerance (NCT04738565).

This article presents selected aspects of an interlaminar shear strength and failure analysis of hybrid fiber metal laminates (FMLs) consisting of alternating layers of a 2024-T3 aluminium alloy and carbon fiber reinforced polymer. Particular attention is paid to the properties of the hybrid FMLs with an additional interlayer of glass composite at the metal-composite interface. The influence of hygrothermal conditioning, the interlaminar shear strength (short beam shear test), and the failure mode were investigated and discussed. It was found that fiber metal laminates can be classified as a material with significantly less adsorption than in the case of conventional composites. Introducing an additional layer of glass composite at the metal-composite interface and hygrothermal conditioning influence the decrease in the interlaminar shear strength. The major forms of damage to the laminates are delaminations in the layer of the carbon composite, at the metal-composite interface, and delaminations between the layers of glass and carbon composites.

The aim of the study was to assess the selected properties of a hybrid organic-inorganic silane sol-gel coating (HSG) used in hybrid fiber metal laminates (FML) in a corrosion environment. The HSG coating on the aluminum alloy was produced using 3M™ AC130-2 formulation consisting of 3-glycidoxypropyl-trimethoxysilane (GPTMS) and tetra-n-propoxyzirconium (zirconium(IV) propoxide) (TPOZ). Laminates consisted of aluminum alloy AA2024-T3 sheets, with carbon fiber reinforced polymers (CFRPs) and a glass fiber reinforced metal-composite structure (GFRP). Potentiodynamic and polarization curve and impedance (EIS) tests were carried out on HSG at ambient temperatures after 1 h and 150 h of soaking. Neutral 0.5 M NaCl and 0.8 M NaCl solutions were used for open circuit potential (OCP) and potentiodynamic tests, and 0.5 NaCl was used for the EIS test. A neutral salt spray (NSS) test was applied to laminates with a 12 week exposure period. The results obtained revealed that the HSG coating did not provide sufficient protection against corrosion of the aluminum alloy in direct contact with an aggressive environment but was effective as an interlayer. Local aluminum sheet perforation did not lead to delamination at the metal-composite interface regardless of the type or configuration of the composite. This confirms the durability of HSG used in FMLs.

Purpose: In this study the comparative results obtained from examinations of two different restorative composites with different cavities filling method are presented. Micro-CT was used for the evaluation of the marginal integrity and quality of composite fillings in connection with microstructural investigations made by both optical and scanning electron microscopy., Materials and Methods: The examinations of dental tooth filings in bulk-fill technique were based on micro-CT and microscopy observations. Two different restorative composites were selected for the study, namely SonicFill- bulk fill and conventional Filtek Z550., Results: The experiment has shown that micro-CT screening analysis for identification of individual components of tooth and fillings systems gives a high quality of images. Thanks to that it was possible to analyze and identify the porosity in the fillings. But the microscopy analysis has shown more information about the internal structure and quality of bonding between composite and enamel/dentin. The SonicFill gives better quality and bonding to structure of teeth than Filtek., Conclusions: SonicFill's filling have more homogenous structure than Filtec. It has a greater share of reinforcement in the form of polygonal particles, in Filtek particles have a shape close to spherical. Sonic Fill gives a better adhesion to tooth., Clinical Relevance: The evaluation of clinical relevance in this research is crucial to simplify the transfer of knowledge from research by materials engineering into practice in dentistry., (© 2018 Wiley Periodicals, Inc.)

Background: Sensitization to food allergens is a common condition in pediatric atopic dermatitis (AD). Recently, the multiple allergen simultaneous test (MAST) allowing for a comprehensive assessment of atopy has been developed, but the usefulness in young AD children is not known. The aim of this study was to determine IgE specificity in AD children using MAST and to compare the results for selected food allergens with the reference ImmunoCap system., Methods: The study enrolled 50 children up to 2 years old with a diagnosis of AD. IgE antibodies were measured with the MAST-immunoblots. Children with specific IgE levels ≥ 0.35 kU/L were identified as sensitized to allergens., Results: Most often children were sensitized to food allergens (egg white and yolk, hazelnuts, potato, cow's milk proteins, wheat flour, codfish, and soybean), but a high percentage of them also had IgE antibodies against house dust mites (12%), grass (10%), and birch (10%). Eight percent of children were sensitized to domestic animals (cats and dogs). Almost perfect (kappa index 0.8 - 1.0) and substantial (kappa index 0.6 - 0.8) agreement between MAST and ImmunoCap was found for food allergens except codfish. Pearson's analysis of antibody classes showed a very strong correlation between two methods (r = 0.8 - 1.0) for egg white, hazelnuts, potato, cow's milk proteins, wheat flour, and soybean, and a strong correlation (r = 0.6 - 0.79) was observed for peanut, egg yolk, and codfish., Conclusions: The study showed the frequent occurrence of IgE antibodies against food and airborne and animal allergens in young AD children and confirmed the usefulness of MAST-immunoblots for screening of sensitization in pediatric patients.

Objectives: The purpose of this study was to evaluate the bond strength of commercially pure CPTi and Ti6Al4V alloy with SiO2 and SiO2-TiO2 intermediate coatings to Triceram low-fusing dental porcelain., Methods: The multilayered systems were characterized from the standpoint of microstructure analysis (SEM), the mode of failure, the nature of bonding and the influence of intermediate coatings on the improvement of bond strength. The SiO2 and SiO2-TiO2 intermediate coatings were applied on the substrate materials by the sol-gel dipping technique. The metal-ceramic bond strength was investigated according to ISO 9693 standards using the three-point flexure bond test., Results: Statistically significant higher bond strength of the metal-porcelain for Ti6A14V alloy (28.24 MPa), Ti6Al4V/SiO2 (32.17 MPa) and Ti6Al4V/SiO2-TiO2 (36.09 MPa) was noted in comparison to CPTi (23.04 MPa), CPTi/SiO2 (27.98 MPa) and CPTi/SiO2-TiO2 (28.84 MPa), respectively. The nature of metal-intermediate coating-porcelain bonding was both mechanical and chemical. The failure in all systems was cohesive and adhesive, mainly adhesive., Significance: The application of SiO2 and SiO2-TiO2 intermediate coatings, produced by the sol-gel method, to both CPTi and Ti6Al4V alloy significantly improves the bond strength of metal-porcelain systems in comparison to the metal substrate only after sandblasting, and may have clinical use.

Cobalt alloys produced in Poland and meant for orthopedic implants were morphologically and toxicologically evaluated. They were implanted subcutaneously in the para-osseous region of rats' heads. The results of the experimental tests strongly suggest the advisability of a clinical research project (study) on the examined cobalt alloys: Medpol-1 and Medpol-2.