Search

We show that the use of 1,3-diaminopropane (DAP) as a chemical modifier at the perovskite/electron-transport layer (ETL) interface enhances the power conversion efficiency (PCE) of 1.7 eV bandgap FACs mixed-halide perovskite single-junction cells, primarily by boosting the open-circuit voltage (VOC) from 1.06 V to 1.15 V. Adding a post-processing annealing step after C60 evaporation, further improves the fill factor (FF) by 20% from the control to the DAP + post-annealing devices. Using hyperspectral photoluminescence microscopy, we demonstrate that annealing helps improve compositional homogeneity at the top and bottom interfaces of the solar cell, which prevents detrimental bandgap pinning in the devices and improves C60 adhesion. Using time-of-flight secondary ion mass spectrometry, we show that DAP reacts with formamidinium present near the surface of the perovskite lattice to form a larger molecular cation, 1,4,5,6-tetrahydropyrimidinium (THP) that remains at the interface. Combining the use of DAP and the annealing of C60 interface, we fabricate Si-perovskite tandems with PCE of 25.29%, compared to 23.26% for control devices. Our study underscores the critical role of chemical reactivity and thermal post-processing of the C60/Lewis-base passivator interface in minimizing device losses and advancing solar-cell performance of wide-bandgap mixed-cation mixed-halide perovskite for tandem application.

Perovskite solar cells (PSCs) offer an efficient, inexpensive alternative to current photovoltaic technologies, with the potential for manufacture via high-throughput coating methods. However, challenges for commercial-scale solution-processing of metal-halide perovskites include the use of harmful solvents, the expense of maintaining controlled atmospheric conditions, and the inherent instabilities of PSCs under operation. Here, we address these challenges by introducing a high volatility, low toxicity, biorenewable solvent system to fabricate a range of 2D perovskites, which highly effective precursor phases for subsequent transformation to alpha-formamidinium lead triiodide (FAPbI3), fully processed under ambient conditions. PSCs utilising our FAPbI3 reproducibly show remarkable stability under illumination and elevated temperature (ISOS-L-2) and "damp heat" (ISOS-D-3) stressing, surpassing other state-of-the-art perovskite compositions. We determine that this enhancement is a consequence of the 2D precursor phase crystallisation route, which simultaneously avoids retention of residual low-volatility solvents (such as DMF and DMSO) and reduces the rate of degradation of FA+ in the material. Our findings highlight both the critical role of the initial crystallisation process in determining the operational stability of perovskite materials, and that neat FA+-based perovskites can be competitively stable despite the inherent metastability of the alpha-phase.

Photovoltaics (PVs) are a critical technology for curbing growing levels of anthropogenic greenhouse gas emissions, and meeting increases in future demand for low-carbon electricity. In order to fulfil ambitions for net-zero carbon dioxide equivalent (CO2eq) emissions worldwide, the global cumulative capacity of solar PVs must increase by an order of magnitude from 0.9 TWp in 2021 to 8.5 TWp by 2050 according to the International Renewable Energy Agency, which is considered to be a highly conservative estimate. In 2020, the Henry Royce Institute brought together the UK PV community to discuss the critical technological and infrastructure challenges that need to be overcome to address the vast challenges in accelerating PV deployment. Herein, we examine the key developments in the global community, especially the progress made in the field since this earlier roadmap, bringing together experts primarily from the UK across the breadth of the photovoltaics community. The focus is both on the challenges in improving the efficiency, stability and levelized cost of electricity of current technologies for utility-scale PVs, as well as the fundamental questions in novel technologies that can have a significant impact on emerging markets, such as indoor PVs, space PVs, and agrivoltaics. We discuss challenges in advanced metrology and computational tools, as well as the growing synergies between PVs and solar fuels, and offer a perspective on the environmental sustainability of the PV industry. Through this roadmap, we emphasize promising pathways forward in both the short- and long-term, and for communities working on technologies across a range of maturity levels to learn from each other., Comment: 160 pages, 21 figures

We report that device architecture engineering has a substantial impact on the reverse bias instability that has been reported as a critical issue in commercializing perovskite solar cells. We demonstrate breakdown voltages exceeding -15 V in typical pin structured perovskite solar cells via two steps: i) using polymer hole transporting materials; ii) using a more electrochemically stable gold electrode. While device degradation can be exacerbated by higher reverse bias and prolonged exposure, our as-fabricated perovskite solar cells completely recover their performance even after stressing at -7 V for 9 hours both in the dark and under partial illumination. Following these observations, we systematically discuss and compare the reverse bias driven degradation pathways in perovskite solar cells with different device architectures. Our model highlights the role of electrochemical reaction rates and species in dictating the reverse bias stability of perovskite solar cells.

Ultranarrow bandwidth single-photon sources operating at room-temperature are of vital importance for viable optical quantum technologies at scale, including quantum key distribution, cloud based quantum information processing networks, and quantum metrology. Here we show a room-temperature ultranarrow bandwidth single-photon source generating polarised photons at a rate of 5MHz based on an inorganic CsPbI3 perovskite quantum dot embedded in a tunable open-access optical microcavity. When coupled to an optical cavity mode, the quantum dot room-temperature emission becomes single-mode and the spectrum narrows down to just 1 nm. The low numerical aperture of the optical cavities enables efficient collection of high-purity single-mode single-photon emission at room-temperature, offering promising performance for photonic and quantum technology applications. We measure 94% pure single-photon emission into a single-mode under pulsed and continuous-wave (CW) excitation.

We show that adding ethylenediamine (EDA) to perovskite precursor solution improves the photovoltaic device performance and material stability of high-bromide-content, methylammonium-free, formamidinium cesium lead halide perovskites FA1-xCsxPb(I1-yBry)3 which are currently of interest for perovskite-on-Si tandem solar cells. Using spectroscopy and hyperspectral microscopy, we show that the additive improves film homogeneity and suppresses the phase instability that is ubiquitous in high-Br perovskite formulations, producing films that remain stable for over 100 days in ambient conditions. With the addition of 1 mol% EDA we demonstrate 1.69 eV-gap perovskite single-junction p-i-n devices with a VOC of 1.22 V, and a champion maximum power point tracked power conversion efficiency of 18.8%, comparable to the best reported methylammonium-free perovskites. Using nuclear magnetic resonance (NMR) spectroscopy and X-ray diffraction techniques, we show that EDA reacts with FA+ in solution, rapidly and quantitatively forming imidazolinium cations. It is the presence of imidazolinium during crystallization which drives the improved perovskite thin-film properties.

All-perovskite tandem solar cells promise high photovoltaic performance at low cost. So far however, their efficiencies cannot compete with traditional inorganic multi-junction solar cells and they generally underperform in comparison to what is expected from the isolated single junction devices. Understanding performance losses in all-perovskite tandem solar cells is a crucial aspect that will accelerate advancement. Here, we perform extensive selective characterization of the individual sub-cells to disentangle the different losses and limiting factors in these tandem devices. We find that non-radiative losses in the high-gap subcell dominate the overall recombination losses in our baseline system as well as in the majority of literature reports. We consecutively improve the high-gap perovskite subcell through a multi-faceted approach, allowing us to enhance the open-circuit voltage ($V_{OC}$) of the subcell by up to 120 mV. Due to the (quasi) lossless indium oxide interconnect which we employ for the first time in all-perovskite tandems, the $V_{OC}$ improvements achieved in the high-gap perovskites translate directly to improved all-perovskite tandem solar cells with a champion $V_{OC}$ of 2.00 V and a stabilized efficiency of 23.7%. The efficiency potential of our optimized all-perovskite tandems reaches 25.2% and 27.0% when determined from electro- and photo-luminescence respectively, indicating significant transport losses as well as imperfect energy-alignment between the perovskite and the transport layers in the experimental devices. Further improvements to 28.4% are possible considering the bulk quality of both absorbers measured using photo-luminescence on isolated perovskite layers. Our insights therefore not only show an optimization example but a generalizable evidence-based strategy for optimization utilizing optical sub-cell characterization., Comment: Main text: 19 pages, 6 figures, supporting information: 17 pages, 18 figures

Two-dimensional halide perovskites are among intensely studied materials platforms profiting from solution based growth and chemical flexibility. They feature exceptionally strong interactions among electronic, optical as well as vibrational excitations and hold a great potential for future optoelectronic applications. A key feature for these materials is the occurrence of structural phase transitions that can impact their functional properties, including the electronic band gap and optical response dominated by excitons. However, to what extent the phase-transitions in two-dimensional perovskites alter the fundamental exciton properties remains barely explored so far. Here, we study the influence of the phase transition on both exciton binding energy and exciton diffusion, demonstrating their robust nature across the phase transition. These findings are unexpected in view of the associated substantial changes of the free carrier masses, strongly contrast broadly considered effective mass and drift-diffusion transport mechanisms, highlighting the unusual nature of excitons in two-dimensional perovskites.

With the rapid progress of perovskite photovoltaics (PV), further challenges arise to meet meet the minimum standards required for commercial deployment. Along with the push towards higher efficiencies, we identify a need to improve the quality and uniformity of reported research data and to focus efforts upon understanding and overcoming failures during operation. In this perspective, as a large and representative consortium of researchers active in this field, we discuss which methods require special attention and issue a series of recommendations to improve research practices and reporting.

Organic-inorganic perovskites have shown great promise towards their application in optoelectronics. The success of this class of material is dictated by the complex interplay between various underlying microscopic phenomena. The structural dynamics of organic cations and the inorganic sublattice after photoexcitation is hypothesized to have a direct effect on the material properties, thereby affecting the overall device performance. Here, we use two-dimensional (2D) electronic spectroscopy to reveal impulsively excited vibrational modes of methylammonium (MA) lead iodide perovskite, which drive the structural distortion after photoexcitation. The vibrational analysis of the measured data allows us to directly monitor the time evolution of the librational motion of the MA cation along with the vibrational coherences of inorganic sublattice. Wavelet analysis of the observed vibrational coherences uncovers the interplay between these two types of phonons. It reveals the coherent generation of the librational motion of the MA cation within ~300 fs, which is complemented by the coherent evolution of the skeletal motion of the inorganic sublattice. We have employed time-dependent density functional theory (TDDFT) to study the atomic motion of the MA cation and the inorganic sublattice during the process of photoexcitation. The TDDFT calculations support our experimental observations of the coherent generation of librational motions in the MA cation and highlight the importance of the anharmonic interaction between the MA cation and the inorganic sublattice. Our calculations predict the transfer of the photoinduced vibrational coherence from the MA cation to the inorganic sublattice, which drives the skeleton motion to form a polaronic state leading to long lifetimes of the charge carriers. This work may lead to novel design principles for next generation of solar cell materials.

Thin (approximately 10 nm) oxide buffer layers grown over lead-halide perovskite device stacks are critical for protecting the perovskite against mechanical and environmental damage. However, the limited perovskite stability restricts the processing methods and temperatures (<=110 C) that can be used to deposit the oxide overlayers, with the latter limiting the electronic properties of the oxides achievable. In this work, we demonstrate an alternative to existing methods that can grow pinhole-free TiOx (x = 2.00+/-0.05) films with the requisite thickness in <1 min without vacuum. This technique is atmospheric pressure chemical vapor deposition (AP-CVD). The rapid but soft deposition enables growth temperatures of >=180 {\deg}C to be used to coat the perovskite. This is >=70 {\deg}C higher than achievable by current methods and results in more conductive TiOx films, boosting solar cell efficiencies by >2%. Likewise, when AP-CVD SnOx (x ~ 2) is grown on perovskites, there is also minimal damage to the perovskite beneath. The SnOx layer is pinhole-free and conformal, which reduces shunting in devices, and increases steady-state efficiencies from 16.5% (no SnOx) to 19.4% (60 nm SnOx), with fill factors reaching 84%. This work shows AP-CVD to be a versatile technique for growing oxides on thermally-sensitive materials., Comment: R.D.R and R.A.J contributed equally. 23 pages. 6 figures

Exciton fine structure splitting in semiconductors reflects the underlying symmetry of the crystal and quantum confinement. Since the latter factor strongly enhances the exchange interaction, most work has focused on nanostructures. Here, we report on the first observation of the bright exciton fine structure splitting in a bulk semiconductor crystal, where the impact of quantum confinement can be specifically excluded, giving access to the intrinsic properties of the material. Detailed investigation of the exciton photoluminescence and reflection spectra of a bulk methylammonium lead tribromide single crystal reveals a zero magnetic field splitting as large as $\sim 200\mu$eV. This result provides an important starting point for the discussion of the origin of the large bright exciton fine structure observed in perovskite nanocrystals., Comment: just accepted in Nano Letters (https://pubs.acs.org/doi/10.1021/acs.nanolett.9b02520)

Previous theoretical calculations show azetidinium has the right radial size to form a 3D perovskite with lead halides [1], and has been shown to impart, as the A-site cation of ABX3 unit, beneficial properties to ferroelectric perovskites [2]. However, there has been very limited research into its use as the cation in lead halide perovskites to date. In this communication we report the synthesis and characterization of azetidinium-based lead mixed halide perovskite colloidal nanocrystals. The mixed halide system is iodine and chlorine unlike other reported nanocrystals in the literature where the halide systems are either iodine/bromine or bromine/chlorine. UV-visible absorbance data, complemented with photoluminescence spectroscopy, reveals an indirect-bandgap of about 1.96 eV for our nanocrystals. Structural characterization using TEM shows two distinct interatomic distances (2.98 +/- 0.15 Angstroms and 3.43 +/- 0.16 Angstroms) and non-orthogonal lattice angles (approximately 112 degrees) intrinsic to the nanocrystals with a probable triclinic structure revealed by XRD. The presence of chlorine and iodine within the nanocrystals is confirmed by EDS spectroscopy. Finally, light-induced electron paramagnetic resonance (LEPR) spectroscopy with PCBM confirms the photoinduced charge transfer capabilities of the nanocrystals. The formation of such semiconducting lead mixed halide perovskite using azetidinium as the cation suggests a promising subclass of hybrid perovskites holding potential for optoelectronic applications such as in solar cells and photodetectors., Comment: 8 pages, 6 Figures, 1 Supplementary information pdf file, 1 XRD indexing information text file

The last five years have witnessed a remarkable progress in the field of lead halide perovskite materials and devices. Examining the existing body of literature reveals staggering inconsistencies in the reported results among different research groups with a particularly wide spread in the photovoltaic performance and stability of devices. In this work we demonstrate that fractional, quite possibly unintentional, deviations in the precursor solution stoichiometry can cause significant changes in the properties of the perovskite layer as well as in the performance and stability of perovskite photovoltaic devices. We show that while the absorbance and morphology of the layers remains largely unaffected, the surface composition and energetics, crystallinity, emission efficiency, energetic disorder and storage stability are all very sensitive to the precise stoichiometry of the precursor solution. Our results elucidate the origin of the irreproducibility and inconsistencies of reported results among different groups as well as the wide spread in device performance even within individual studies. Finally, we propose a simple experimental method to identify the exact stoichiometry of the perovskite layer that researchers can employ to confirm their experiments are performed consistently without unintentional variations in precursor stoichiometry.

Many optoelectronic properties have been reported for lead halide perovskite polycrystalline films. However, ambiguities in the evaluation of these properties remain, especially for long-range lateral charge transport, where ionic conduction can complicate interpretation of data. Here we demonstrate a new technique to measure the long-range charge carrier mobility in such materials. We combine quasi-steady-state photo-conductivity measurements (electrical probe) with photo-induced transmission and reflection measurements (optical probe) to simultaneously evaluate the conductivity and charge carrier density. With this knowledge we determine the lateral mobility to be ~ 2 cm2/Vs for CH3NH3PbI3 (MAPbI3) polycrystalline perovskite films prepared from the acetonitrile/methylamine solvent system. Furthermore, we present significant differences in long-range charge carrier mobilities, from 2.2 to 0.2 cm2/Vs, between films of contemporary perovskite compositions prepared via different fabrication processes, including solution and vapour phase deposition techniques. Arguably, our work provides the first accurate evaluation of the long-range lateral charge carrier mobility in lead halide perovskite films, with charge carrier density in the range typically achieved under photovoltaic operation.

In a combined theoretical and experimental work, we investigate X-ray Absorption Near-Edge Structure (XANES) spectroscopy of the I $L_3$ and the Pb $M_5$ edges of the methylammonium lead iodide ($\textrm{MAPbI}_3$) hybrid inorganic-organic perovskite and its binary phase $\textrm{PbI}_2$. The absorption onsets are dominated by bound excitons with sizable binding energies of a few hundred meV and pronounced anisotropy. The spectra of both materials exhibit remarkable similarities, suggesting that the fingerprints of core excitations in $\textrm{MAPbI}_3$ are essentially given by its inorganic component, with negligible influence from the organic groups. The theoretical analysis complementing experimental observations provides the conceptual insights required for a full characterization of this complex material.

Perovskite-based optoelectronic devices have gained significant attention due to their remarkable performance and low processing cost, particularly for solar cells. However, for perovskite light-emitting diodes (LEDs), non-radiative charge carrier recombination has limited electroluminescence (EL) efficiency. Here we demonstrate perovskite-polymer bulk heterostructure LEDs exhibiting record-high external quantum efficiencies (EQEs) exceeding 20%, and an EL half-life of 46 hours under continuous operation. This performance is achieved with an emissive layer comprising quasi-2D and 3D perovskites and an insulating polymer. Transient optical spectroscopy reveals that photogenerated excitations at the quasi-2D perovskite component migrate to lower-energy sites within 1 ps. The dominant component of the photoluminescence (PL) is primarily bimolecular and is characteristic of the 3D regions. From PL quantum efficiency and transient kinetics of the emissive layer with/without charge-transport contacts, we find non-radiative recombination pathways to be effectively eliminated. Light outcoupling from planar LEDs, as used in OLED displays, generally limits EQE to 20-30%, and we model our reported EL efficiency of over 20% in the forward direction to indicate the internal quantum efficiency (IQE) to be close to 100%. Together with the low drive voltages needed to achieve useful photon fluxes (2-3 V for 0.1-1 mA/cm2), these results establish that perovskite-based LEDs have significant potential for light-emission applications.

We explore the degradation behaviour under continuous illumination and direct oxygen exposure of inverted unencapsulated formamidinium(FA)0.83Cs0.17Pb(I0.8Br0.2)3, CH3NH3PbI3, and CH3NH3PbI3-xClx perovskite solar cells. We continuously test the devices in-situ and in-operando with current-voltage sweeps, transient photocurrent, and transient photovoltage measurements, and find that degradation in the CH3NH3PbI3-xClx solar cells due to oxygen exposure occurs over shorter timescales than FA0.83Cs0.17Pb(I0.8Br0.2)3 mixed-cation devices. We attribute these oxygen-induced losses in the power conversion efficiencies to the formation of electron traps within the perovskite photoactive layer. Our results highlight that the formamidinium-caesium mixed-cation perovskites are much less sensitive to oxygen-induced degradation than the methylammonium-based perovskite cells, and that further improvements in perovskite solar cell stability should focus on the mitigation of trap generation during ageing.

Hybrid organic-inorganic perovskites (HOIPs) have recently emerged as highly promising solution-processable materials for photovoltaic (PV) and other optoelectronic devices. HOIPs represent a broad family of materials with properties highly tuneable by the ions that make up the perovskite structure as well as their multiple combinations. Interestingly, recent high-efficiency PV devices using HOIPs with substantially improved long-term stability have used combinations of different ionic compositions. The structural dynamics of these systems are unique for semiconducting materials and are currently argued to be central to HOIPs stability and charge-transport properties. Here, we studied the impact of ionic composition on phonon speeds of HOIPs from Brillouin spectroscopy experiments and density functional theory calculations for FAPbBr$_3$, MAPbBr$_3$, MAPbCl$_3$, and the mixed halide MAPbBr$_{1.25}$Cl$_{1.75}$. Our results show that the acoustic phonon speeds can be strongly modified by ionic composition, which we explain by analysing the lead-halide sublattice in detail. The vibrational properties of HOIPs are therefore tuneable by using targeted ionic compositions in the perovskite structure. This tuning can be rationalized with non-trivial effects, for example, considering the influence of the shape and dipole moment of organic cations. This has an important implication to further improvements in the stability and charge-transport properties of these systems.

We have accurately determined the exciton binding energy and reduced mass of single crystals of methylammonium lead tri-iodide using magneto-reflectivity at very high magnetic fields. The single crystal has excellent optical properties with a narrow line width of $\sim 3$meV for the excitonic transitions and a 2s transition which is clearly visible even at zero magnetic field. The exciton binding energy of $16 \pm 2$meV in the low temperature orthorhombic phase is almost identical to the value found in polycrystalline samples, crucially ruling out any possibility that the exciton binding energy depends on the grain size. In the room temperature tetragonal phase, an upper limit for the exciton binding energy of $12 \pm 4$ meV is estimated from the evolution of 1s-2s splitting at high magnetic field., Comment: 5 pages, 4 figures

A$_2$BB$^\prime$X$_6$ halide double perovskites based on bismuth and silver have recently been proposed as potential environmentally-friendly alternatives to lead-based hybrid halide perovskites. In particular, Cs$_2$BiAgX$_6$ (X = Cl, Br) have been synthesized and found to exhibit band gaps in the visible range. However, the band gaps of these compounds are indirect, which is not ideal for applications in thin film photovoltaics. Here, we propose a new class of halide double perovskites, where the B$^{3+}$ and B$^{+}$ cations are In$^{3+}$ and Ag$^{+}$, respectively. Our first-principles calculations indicate that the hypothetical compounds Cs$_2$InAgX$_6$ (X = Cl, Br, I) should exhibit direct band gaps between the visible (I) and the ultraviolet (Cl). Based on these predictions, we attempt to synthesize Cs$_2$InAgCl$_6$ and Cs$_2$InAgBr$_6$, and we succeed to form the hitherto unknown double perovskite Cs$_2$InAgCl$_6$. X-ray diffraction yields a double perovskite structure with space group $Fm\overline{3}m$. The measured band gap is 3.3 eV, and the compound is found to be photosensitive and turns reversibly from white to orange under ultraviolet illumination. We also perform an empirical analysis of the stability of Cs$_2$InAgX$_6$ and their mixed halides based on Goldschmidt's rules, and we find that it should also be possible to form Cs$_2$InAg(Cl$_{1-x}$Br$_{x}$)$_6$ for $x<1$. The synthesis of mixed halides will open the way to the development of lead-free double perovskites with direct and tunable band gaps.

Perovskite solar cells (PSC) are shown to behave as coupled ionic-electronic conductors with strong evidence that the ionic environment moderates both the rate of electron-hole recombination and the band offsets in planar PSC. Numerous models have been presented to explain the behavior of perovskite solar cells, but to date no single model has emerged that can explain both the frequency and time dependent response of the devices. Here we present a straightforward coupled ionic-electronic model that can be used to explain the large amplitude transient behavior and the impedance response of PSC., Comment: 16 pages, 7 figures

We demonstrate four and two-terminal perovskite-perovskite tandem solar cells with ideally matched bandgaps. We develop an infrared absorbing 1.2eV bandgap perovskite, $FA_{0.75}Cs_{0.25}Sn_{0.5}Pb_{0.5}I_3$, that can deliver 14.8 % efficiency. By combining this material with a wider bandgap $FA_{0.83}Cs_{0.17}Pb(I_{0.5}Br_{0.5})_3$ material, we reach monolithic two terminal tandem efficiencies of 17.0 % with over 1.65 volts open-circuit voltage. We also make mechanically stacked four terminal tandem cells and obtain 20.3 % efficiency. Crucially, we find that our infrared absorbing perovskite cells exhibit excellent thermal and atmospheric stability, unprecedented for Sn based perovskites. This device architecture and materials set will enable 'all perovskite' thin film solar cells to reach the highest efficiencies in the long term at the lowest costs.

Lead-halide perovskites are promising materials for opto-electronic applications. Recent reports indicated that their mechanical and electronic properties are strongly affected by the lattice vibrations. Herein we report far-infrared spectroscopy measurements of CH$_{3}$NH$_{3}$Pb(I/Br/Cl)$_{3}$ thin films and single crystals at room temperature and a detailed quantitative analysis of the spectra. We find strong broadening and anharmonicity of the lattice vibrations for all three halide perovskites, which indicates dynamic disorder of the lead-halide cage at room temperature. We determine the frequencies of the transversal and longitudinal optical phonons, and use them to calculate, via appropriate models, the static dielectric constants, polaron masses, electron-phonon coupling constants, and upper limits for the phonon-scattering limited charge carrier mobilities. Within the limitations of the model used, we can place an upper limit of 200$\,$cm$^{2}$V$^{-1}$s$^{-1}$ for the room temperature charge carrier mobility in MAPbI$_{3}$ single crystals. Our findings are important for the basic understanding of charge transport processes and mechanical properties in metal halide perovskites.

Hysteresis in the current-voltage characteristics of hybrid organic-inorganic perovskite-based solar cells is one of the fundamental aspects of these cells that we do not understand well. One possible cause, suggested for the hysteresis, is polarization of the perovskite layer under applied voltage and illumination bias, due to ion migration within the perovskite. To study this problem systemically current-voltage characteristics of both regular (light incident through the electron conducting contact) and so-called inverted (light incident through the hole conducting contact) perovskite cells were studied at different temperatures and scan rates. We explain our results by assuming that the effects of scan rate and temperature on hysteresis are strongly correlated to ion migration within the device, with the rate-determining step being ion migration at/across the interfaces of the perovskite layer with the contact materials. By correlating between the scan rate with the measurement temperature we show that the inverted and regular cells operate in different hysteresis regimes, with different activation energies of 0.28+-0.04 eV and 0.59+-0.09 eV, respectively. We suggest that the differences, observed between the two architectures are due to different rates of ion migration close to the interfaces, and conclude that the diffusion coefficient of migrating ions in the inverted cells is 3 orders of magnitude higher than in the regular cells, leading to different accumulation rates of ions near the interfaces. Analysis of VOC as a function of temperature shows that the main recombination mechanism is trap-assisted (Shockley-Read Hall, SRH) in the space charge region, similar to what is the case for other thin film inorganic solar cells., Comment: 47 pages including supplementary information