Search

This article presents three efficient rectifiers for radio frequency energy harvesting (RFEH) systems operating at the fifth generation (5G) band (3.5 GHz). Each rectifier operates at various input power levels (high, low, and across a wide power range). The high and low-power rectifiers feature a single serial topology using HSMS-2860 and SMS-7630 Schottky diodes, respectively, along with microstrip lines to implement the input and output filters and the impedance matching network. At an radio frequency (RF) power level of 15 dBm, the high-power rectifier harvests 67.4% to direct current (DC) power with a 300 Ω load resistor and an output voltage of 2.5 V. The low-power rectifier achieves its maximum power conversion efficiency (PCE) at -2 dBm, reaching 45% efficiency with a 1,200 Ω load. The rectifier with a extended input power range comprises two branches of subrectifiers functioning at both high and low power levels. Depending on the power level, the considered subrectifier harvests radio frequency power into DC power, while the other subrectifier is deactivated. Across a power span of 32.5 dB (ranging from -13 to 19.5 dBm), the rectifier maintains an efficiency above 30%. The proposed rectifiers are efficient and suitable for implementation in 5G-enabled RFEH systems. [ABSTRACT FROM AUTHOR]

This study introduces a novel uninterruptible power supply (UPS) configuration that integrates active power filter (APF) capabilities within a single-phase matrix converter (SPMC) framework. Power disruptions, particularly affecting critical loads, can lead to substantial economic damages. Historically, conventional UPS systems utilized dual separate converters to function as a rectifier and an inverter, without incorporating any power factor correction (PFC) mechanisms. Such configurations suffered from diminished power density, compromised reliability, and spatial limitations. To address these issues, this research proposes an enhanced UPS design that incorporates APF features into the SPMC. The focus of this investigation is on the efficiency of alternating current (AC) to direct current (DC) conversion and the reverse process utilizing this advanced UPS model. The SPMC is selected to supplant the rectifier and inverter units traditionally employed in UPS architectures. A novel integrated switching strategy is formulated to facilitate the operation of the UPS in either rectifier (charging) or inverter (discharging) modes, contingent upon the operational state. The performance and efficacy of the devised circuit design and switching technique are substantiated through simulations conducted in MATLAB/Simulink 2019 and empirical evaluations using a test rig. The findings demonstrate that the voltage generated is sinusoidal and synchronized with the supply current, thereby minimizing the total harmonic distortion (THD) and enhancing both the power factor and the transition efficiency of the UPS system between its charging and discharging states. [ABSTRACT FROM AUTHOR]

In this paper, a CGH40010F GaN-based wideband RF rectifier with high rectification efficiency is presented. A novel continuous class-EFJ-mode rectifier is constructed by combining a continuous class-J-mode rectifier and class-EF-mode rectifier under specific impedance conditions. This novel continuous class-EFJ-mode rectifier has high rectification efficiency and wide bandwidth at the same time. For validation, a wideband high-efficiency class-EFJ-mode rectifier functioning within the 2.0–3.0 GHz range is designed, fabricated, and measured. The measurements indicate that, with an input power of 40 dBm and a resistance of 72 Ω on the dc load, the implemented rectifier sustains a rectification efficiency exceeding 60% across its entire operational frequency band. Meanwhile, the dimensions of the circuits are only 3 cm × 3.1 cm. [ABSTRACT FROM AUTHOR]

A watt‐scale dual‐band rectifier with excellent efficiency and a wide input power range is proposed in this letter. The rectifier is composed of two stages. In the first stage, a novel impedance‐matching network with four transmission lines (TLINs) is proposed, which can independently change the input impedance of each band over a large input power range. This approach by deriving closed‐form analytical equations to obtain an exact solution. To test the parameters of the first part of the TLINs in validation and to guarantee excellent efficiency, two TLINs are used in the second stage to control the harmonics. At 0 dBm, the power conversion efficiency (PCE) is 51.2% and 56.7% at 2.4 and 5.8 GHz, respectively, at a load of 1.2 kΩ. At 2.4 GHz, PCE reaches a peak of 68% at 13 dBm. At 5.8 GHz, PCE enhances up to 89% at 17 dBm. At 2.4 and 5.8 GHz, the PCE exceeds 70% of the peak over a wide input power range of −3 to 18 and 1.5–18 dBm, respectively. For verification, the proposed rectifier is fabricated. The simulation results are consistent with the measurements. The proposed rectifier performs well in terms of compactness and rectification effectiveness. It provides a solution for powering low‐power devices. [ABSTRACT FROM AUTHOR]

A metasurface array for electromagnetic (EM) energy harvesting for Wi-Fi bands is presented in this paper; the metasurface array consists of a metasurface unit, a rectifier, and a load resistor. Each row of unit cells in the array is interconnected to form an energy transfer channel, which enables the transfer and concentration of incident power. Furthermore, at the terminal of the channel, a single series diode rectifier circuit and a load resistor are integrated in a coplanar manner. It is used to rectify the energy in Wi-Fi bands and enables DC energy harvesting across the load. Finally, a 5 × 7 prototype of the metasurface array is fabricated and measured for the verification of the rationality of the design. Testing in an anechoic chamber shows that the prototype achieves a 72% RF-DC efficiency at 5.9 GHz when the available incident power is about 7 dBm. [ABSTRACT FROM AUTHOR]

This work presents the two port ultra-wide band MIMO antenna with novel isolation structure and dual band RF Rectifier for 3.3 GHz and 4.65 GHz frequencies for RF energy harvesting applications. The anticipated antenna is systematically examined within the ultra-wideband (UWB) range from 3.1 GHz to 10.6 GHz design frequency with four different steps: Antenna 1, Antenna 2, Antenna 3 and Antenna 4 (optimal design) are chosen for comprehensive study. A unique isolation structure was developed between two identical elements separated by 10 mm, resulting in an enhanced isolation of −23.5 dB at 3.15 GHz, −27 dB at 5.8 GHz, −28 dB at 9.26 GHz and greater than −34 dB at 7.5 GHz. The suggested antenna resonates at UWB band and have fractional bandwidth of 118.66 % and a peak gain of 4.1 dB at 3.15 GHz, 3.68 dB at 5.8 GHz, 6.4 dB at 7.5 GHz and 3.2 dB at 9.26 GHz has been obtained. Radiation efficiencies of 92.5 %, 95 %, 90 % and 84.5 % at 3.15 GHz, 5.8 GHz, 7.5 GHz and 9.26 GHz were obtained respectively. The recommended MIMO performance is simulated using HFSS in terms of ECC, DG, MEG and CCL. The results adhere to specified requirements and confirmed by experimentation. An HFSS simulated dataset of reflection coefficient is used as input for the various ML algorithms namely, Support Vector Machine (SVM), Ensemble, k-nearest neighbors' algorithm (KNN) and Gaussian Process Regression (GPR) models are trained with 80 % of the data and testing with 20 % of the data. The test results are compared and corresponding performance values of MAE, RMSE, MSE & R2 are 0.00029, 0.00197, 3.87e−6 and 1.0 validation results and corresponding test results are 0.00031, 0.00229, 5.20e−6 and 0.999. Finally, the proposed dual band rectifier with a shorted stub is tested for harvesting applications at 3.3 GHz and 4.65 GHz frequency and it attained RF to DC conversion efficiencies of 69 % and 55.40 % respectively. [ABSTRACT FROM AUTHOR]

This brief proposes an innovational method to design a broadband high‐efficiency transistor‐based rectifier with high rectification efficiency. The theory of the class‐F−1 rectifier with the input second harmonic component is explored. Moreover, the mathematical variations of rectification efficiency and load/source impedances versus several crucial design parameters are established. The variation relationships indicate that the rectification efficiency can roughly maintain constant across a large input second harmonic range, resulting in more available design impedances. Thus, this provides the possibility to design wideband rectifiers. For validation, a broadband high‐efficiency class‐F−1 rectifier (operating in 1.6–2.6 GHz) using a GaN transistor is designed, assembled, and measured. Measurements indicate a rectification efficiency of between 72.1% and 82.4% under the condition of Rdc = 67 Ω and Pin = 40 dBm. The realized rectifier exhibits the largest relative bandwidth compared with transistor‐based rectifiers reported before. The methodology presented in this brief provides a promising approach for broadband high‐efficiency GaN HEMT‐based rectifiers. [ABSTRACT FROM AUTHOR]

Rectifier plays a pivotal role in wireless power transfer systems. While numerous studies have concentrated on enhancing efficiency and bandwidth at specific high-power levels, practical scenarios often involve unpredictable power inputs. Consequently, a distinct need arises for a rectifier that demonstrates superior efficiency across a broad range of input power levels. This paper introduces a high-power RF-to-DC rectifier designed for WPT applications, featuring an ultrawide dynamic range of input power. The rectification process leverages a GaN (gallium nitride) high electron mobility transistor (HEMT) to efficiently handle high power levels up to 12.6 W. The matching circuit was designed to ensure that the rectifier will operate in class-F mode. A Schottky diode is incorporated into the design for relatively lower-power rectification. Seamless switching between the rectification modes of the two circuits is accomplished through the integration of a circulator. The proposed rectifier exhibits a 27.5 dB dynamic range, achieving an efficiency exceeding 55% at 2.4 GHz. Substantial improvement in power handling and dynamic range over traditional rectifiers is demonstrated. [ABSTRACT FROM AUTHOR]

This paper presents a comprehensive review of the design and implementation methods of low-power piezoelectric energy harvesting circuits, which in the last few years have gained an extremely large range of applications like the power sources of wearable electronic devices, such as biometrical sensors. Before examining the electronic circuitries of the self-supplied power devices, an overview of the structure, equivalent electrical circuits, and basic parameters of the piezoelectric generators and MEMSs as energy harvesting elements is presented. The structure of energy storage elements (parallel-plate capacitors and thin-film supercapacitors), suitable for this type of application, is also presented. The description of these components from an electrical point of view allows them to be easily workable when connected to the various power conversion electronic circuits. Based on an overview of the structure and the principles of operation, as well as some analytical expressions for energy efficiency evaluation, a comprehensive comparative analysis is presented. Depending on the advantages and disadvantages of the known circuit configurations, the basic electrical and design parameters are systematized in tabular form. Practical realizations of piezoelectric power conversion circuits are also presented in graphic form, ensuring the optimal value of energy efficiency and compactness in the construction of the devices. [ABSTRACT FROM AUTHOR]

This article introduces an isolated three-phase six-pulse rectifier using a solid-state transformer. The line frequency utility grid voltage is modulated by a frequency boost converter. This converter exists two parts. The first part is the rectifier section, and the second one is the inverter section. Then after, three-phase diode rectifier is powered by the medium frequency transformer 2 kHz to shrink the transformer size upto 20% or even 10% depensing to the frequency operating range for silicon steel core materials. The aim of this study is to shrink the occupied size of the rectifier using a higher frequency transformer. The study realizes that the grid line current has the same frequency contents as a regular three phase rectifier. In other words, the presented idea results in smaller weight and size while sustaining the performance of input current total harmonic distortion THD=31%. High power density power electronics converter would be extremely valuable for applications such as electric vehicle railways and aircraft. The proposed approach is reliable and easy to use. The solid-state transformer contributes to isolating and improving the overall converter's power density. Simulation results for the 16 kW converter were verified using MATLAB Simulink. [ABSTRACT FROM AUTHOR]

A new type of single–conversion–step wide–input–range versatile step–up/down three–voltage–level power–factor correction stage is presented in this manuscript. The rectifier can operate both in continuous–conduction mode and discontinuous–conduction mode. First, the rectifier's principle of operation is described, and then the innovative rectifier is analyzed in continuous and discontinuous–conduction modes. After, an average model for the innovative rectifier is developed. Lastly, the proposed theory is experimentally validated using a multiplier–less dual–control–loop mode at discontinuous–conduction modes. It is shown that although no multiplier is used in the control circuitry, the power factor is near unity. It is revealed that the rectifier can swing the output voltage from 50 V to 900 V while the input voltage is 230 Vrms. Although the rectifier output has a split DC bus with three voltage levels, the required control effort is low, and the output voltage is balanced. The innovative topology suits any standard power–factor correction rectifier application, dual–stage low–voltage power supply, and three–level voltage supplement for low–harmonic inverters. Since the rectifier's output–voltage swing is extremely wide, energy storage systems and electric vehicle batteries are suitable applications. [ABSTRACT FROM AUTHOR]

This paper presents a novel adaptive reconfigurable rectifier architecture for radio frequency energy harvesting (RFEH); in addition, a new metric for high-efficiency dynamic range (DR) is proposed. The presented rectifier architecture is based on a double-sided diode-feedback cross-coupled differential-drive rectifier (CCDR) structure incorporating self-body bias for reconfigurable operation. An adaptive structure based on a Schmitt trigger is proposed to adaptively switch the rectifier connection without auxiliary voltage (Vaux), with two rectifier stages in parallel at low power and in series at high power. The system is simulated at a 180 nm CMOS process and the results show more than 17 dB DR at 900 MHz, with efficiency higher than 50% at a 100 kΩ load. [ABSTRACT FROM AUTHOR]

Multiple parameter environment monitoring via wireless Internet of Thing sensors is growing rapidly, thanks to low power techniques of the node. More importantly, the ever more complex and highly efficient energy harvesting systems enable long-term continuous monitoring in inaccessible environments without needing to change the battery. This paper reviews existing energy harvesting modalities, including photovoltaic, piezoelectric, pyroelectric, electromagnetic, and vibration, together with circuit techniques of interfacing power management circuits for energy harvesters. Moreover, techniques used to interface with multiple mode energy harvesters to obtain a stable output power with optimal power efficiency are discussed as an emerging direction. The state-of-the-art energy harvesting systems together with future development trends are provided.

In this work, a 2.4 GHz fully woven textile-integrated circularly polarized rectenna intended for wireless power transfer applications is presented. A rectangular patch with truncated corners is used as the radiating element. It is fed through a T-match structure, which allows the control of the input impedance without requiring any additional impedance-matching network. A single-diode rectifier topology was considered to simplify the entire structure and to facilitate its integration with the antenna. The rectifier and the antenna are optimized together through a co-simulation strategy, in which the input impedance of the antenna is adjusted to match the input impedance of the rectifier, ensuring maximum power transfer between them. At the implementation stage, the rectifier is first mounted on a carrier thread, which is then incorporated into the woven structure. This approach, in combination with the chosen antenna feeding technique, which requires no additional elements for impedance matching purposes, provides a high degree of integration between the antenna and the rectifier. The rectenna was experimentally characterized, providing a 45% overall efficiency under realistic working conditions.

This review explores the various strategies used to widen the input power (P $_{\mathrm {IN}}$ ) dynamic range of an RF-DC rectifier and analyzes the recent developments reported in the literature. This development is insightful as the PIN dynamic range is crucial for systems adopting wireless power transfer (WPT) or wireless energy harvesting (EH) for both near- and far-field applications to mitigate the reliance on the battery as its primary power source. However, the RF-DC rectifier exhibits non-linear characteristics, resulting in a narrow PIN band for reasonable power conversion efficiency (PCE). The different strategies reported in the literature are discussed and classified into three main concepts: reconfigurable, multi-path, and self-biased rectifiers. Despite having different design constraints and considerations during the inception of the reported work in the literature, this article analyzes and provides the general development trend, merits, and demerits.

This study introduces a highly efficient harmonic reflection (HR) rectenna designed for precise wireless power transfer (WPT) antenna alignment. The proposed HR rectenna not only converts RF signals to DC power but also transmits a second-harmonic signal to determine the beam alignment between the device and transmitter in diverse environments, including free space and within a medium such as the human body. The proposed rectenna integrates a dual-band slot patch antenna and a HR rectifier. The HR rectifier is configured using a matched voltage doubler and independent second-harmonic impedance control network (ISHICN). To reduce the complexity of the dual-band matching network and mitigate the coupling between the fundamental and harmonic impedances of the HR rectifier, an independent matching technique is applied to a matched voltage doubler and ISHICN, to ensure matching at both the fundamental and harmonic frequencies. Measurement results of the proposed HR rectifier demonstrate impressive performance metrics, including a peak power conversion efficiency (PCE) of 71.6 % at 28 dBm of input power, as well as a peak conversion gain (CG) of -10.4 dB at 8.4 dBm of input power. Notably, the frequency range for PCE >50 % and CG $\gt -22$ dB spans over 0.8 GHz. The antenna adopts a microstrip-fed slot patch design for wide beamwidth at 2.45 GHz and 4.9 GHz, achieving peak gains of 4.9 dBi and 3.8 dBi, respectively. The HR rectenna is integrated with a dual-band microstrip-fed slot patch antenna with sized 60 mm $\times 72.5$ mm. The implemented rectenna is verified to be an efficient WPT receiver through an antenna beam alignment experiment in free space and minced-pork environment.

This paper presents a wireless power conversion system designed for biomedical implants, with integrated automatic resonance tuning. The automatic tuning mechanism improves power transfer efficiency (PTE) by finely tuning the resonant frequency of the power link and maximizing the rectified voltage. This adjustment ensures robust and reliable remote powering, even in the face of environmental changes and process variations, while also minimizing tissue exposure to power. On-chip switched array capacitors are connected in parallel with the resonant capacitor, and the system identifies the optimal switched capacitor combination for the highest rectified voltage by iterating over each of them. The proposed system is implemented and fabricated in standard 180nm CMOS technology, with a total area of 0.339 mm2, and its operation is verified. The measurement results demonstrate that this system provides tolerance up to mismatches equivalent to 75 pF capacitance variation in LC tank, ±15% LC variation in this design. The system offers a PTE enhancement from 9.1% to 30.2% in case of high LC variation, and the tuning control consumes 154.7 $\mu \text{W}$ of power during resonance tuning. Moreover, the power conversion chain delivers an optimized rectified voltage along with a regulated voltage of 1.8 V.

The use of RF harvesting as a power source for low-power systems, such as wearables, wireless sensor nodes, and Internet of Things, has gained attention. The primary obstacle to develop an effective RF-DC system has been the RF rectifier. The method most frequently employed in the design of RF-DC converters is called Cross-Coupled Differential Drive (CCDD). To enhance the DC output voltage, multistage systems are typically employed. In these designs, DC output will reach saturation as the number of stages rises. This is because the NMOS threshold voltage will rise if the bulk of the NMOS is connected to the lowest potential. An alternative is to employ the twin-well CMOS process, which is more expensive than the regular n-well process. A novel CMOS RF-DC converter is presented in this brief. The design is hybrid in the sense the first stage is designed using a standard CCDD, while the second and subsequent stages are designed exclusively with PMOS transistors. This allows the use of the n-well process during fabrication. With CADENCE Virtuoso in $0.18~\mu \text{m}$ TSMC CMOS technology, the suggested design’s functionality is verified. The design is functional and achieves 45% efficiency and a power dynamic range of 23dB for power conversion efficiency (PCE) >20%, according to simulation findings.

A wide-speed, ultra-light power generation system is a critical power generation unit structure, often because of its high efficiency and power density. Lightness and reliability are two key design indicators within the system, albeit they could lead to contradictory problems, particularly in systems containing prime movers, batteries, generators, rectifiers, and inverters. Ultra-light generator sets are facing more severe problems and contradictions in designing in terms of matching, coordinating, and stabilizing the components in the systems. This paper describes the system design of a low-cost and high-reliability microgenerator set: a gasoline engine, three-phase permanent magnet synchronous generator, rectifier, and inverter. Moreover, the matching relationship between the four parts and the design effect of each part of the power generation system was analyzed, simulated, and tested to verify the effectiveness and feasibility of the so-designed system. [ABSTRACT FROM AUTHOR]

A three-stage rectifier containing three diodes is proposed in this paper. These diodes with different threshold voltages are located in three branches to achieve high conversion efficiency for different input power levels. By combining the three branches, the proposed rectifier is enabled to achieve high conversion efficiency over a wide dynamic input power range. A prototype of a 2.4 GHz rectifier is designed, simulated and measured. The efficiency of the three branches remains above 30% in the power range of-10-11 dBm, 11-24 dBm and 24-35 dBm, respectively. The measured results show that the conversion efficiency maintains over 40% within the input power range of -6-25 dBm, with the maximum conversion efficiency reaching up to 71. 2%. It indicates that the proposed rectifier can achieve low sensitivity to input power variation and high conversion efficiency over an ultra-wide input power range, which can be used in energy harvesting or dynamic wireless power transmission systems. [ABSTRACT FROM AUTHOR]

Copyright of Electric Drive is the property of Electric Drive Editorial Office and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

In this study, a high-efficiency, high-power synchronous rectifier based on transistors was designed. The widely used diode-based rectifiers have a relatively simple structure but are unsuitable for high-power applications, such as unmanned aerial vehicle and electric vehicle charging. In contrast, transistor-based rectifiers operate by reversing the power flow of a switch-mode power amplifier from the load to the DC supply based on time-reversal duality and can rectify efficiently, even at a high power of 30 dBm or more. The proposed transistor-based synchronous rectifier was designed to have a high rectification efficiency by controlling the harmonics to operate in the inverse Class-F mode and achieved a peak efficiency of 73.2% at an input power of 37 dBm. [ABSTRACT FROM AUTHOR]

Heterostructures of two‐dimensional materials realise novel and enhanced physical phenomena, making them attractive research targets. Compared to inorganic materials, coordination nanosheets have virtually infinite combinations, leading to tunability of physical properties and are promising candidates for heterostructure fabrication. Although stacking of coordination materials into vertical heterostructures is widely reported, reports of lateral coordination material heterostructures are few. Here we show the successful fabrication of a seamless lateral heterojunction showing diode behaviour, by sequential and spatially limited immersion of a new metalladithiolene coordination nanosheet, Zn3BHT, into aqueous Cu(II) and Fe(II) solutions. Upon immersion, the Zn centres in insulating Zn3BHT are replaced by Cu or Fe ions, resulting in conductivity. The transmetallation is spatially confined, occurring only within the immersed area. We anticipate that our results will be a starting point towards exploring transmetallation of various two‐dimensional materials to produce lateral heterojunctions, by providing a new and facile synthetic route. [ABSTRACT FROM AUTHOR]

In this paper, photonic generation of arbitrary shape radio-frequency (RF) waveforms like triangular, square and fullwave rectifier types are demonstrated based on a dual-parallel Mach–Zehnder modulator (DP-MZM) driven by a single sinusoidal RF signal. In the proposed technique, one of the sub-MZM (MZM-2) has no driven signal, while other the sub-MZMs (MZM-1) of the DP-MZM is driven by the sinusoidal RF signal. The powers of even and odd-order sidebands are separately controlled by proper adjustment of modulation index through modulating the bias of the MZM-1. An RF signal with controllable harmonics are generated, after detecting the modulated signal by a photodetector. Thus, by separately modulating its harmonics a desired RF waveform is generated. The proposed method is theoretically analysed followed by experimental validation. [ABSTRACT FROM AUTHOR]

The paper introduces a new circuit structure of precision full-wave rectifier, without the requirement of any diode(s) and passive component(s), which operates in current mode. The proposed structure of the rectifier employs a single current follower differential input transconductance amplifier and two MOS transistors only. The use of the least number of active components makes the circuit structure simple and favorable to the contemporary integration technology. The proposed rectifier has wider input current dynamic range (±1.6 mA), lower current offset (84 pA), and can operate up to 30 MHz frequency. Additionally, the circuit is easily cascadable, temperature insensitive, and less affected by process variation, MOS transistors mismatch, and supply voltage variation. The rectifier circuit is verified through 0.18 µm gpdk technology-based post-layout simulation results using the cadence Virtuoso tool. The rectification accuracy is examined through the parameters, such as average value ratio and root mean square error. The proposed rectifier's layout measures 31.95 µm × 31.35 µm in size. [ABSTRACT FROM AUTHOR]

A metasurface array for electromagnetic (EM) energy harvesting for Wi-Fi bands is presented in this paper; the metasurface array consists of a metasurface unit, a rectifier, and a load resistor. Each row of unit cells in the array is interconnected to form an energy transfer channel, which enables the transfer and concentration of incident power. Furthermore, at the terminal of the channel, a single series diode rectifier circuit and a load resistor are integrated in a coplanar manner. It is used to rectify the energy in Wi-Fi bands and enables DC energy harvesting across the load. Finally, a 5 × 7 prototype of the metasurface array is fabricated and measured for the verification of the rationality of the design. Testing in an anechoic chamber shows that the prototype achieves a 72% RF-DC efficiency at 5.9 GHz when the available incident power is about 7 dBm.

This study introduces a novel uninterruptible power supply (UPS) configuration that integrates active power filter (APF) capabilities within a single-phase matrix converter (SPMC) framework. Power disruptions, particularly affecting critical loads, can lead to substantial economic damages. Historically, conventional UPS systems utilized dual separate converters to function as a rectifier and an inverter, without incorporating any power factor correction (PFC) mechanisms. Such configurations suffered from diminished power density, compromised reliability, and spatial limitations. To address these issues, this research proposes an enhanced UPS design that incorporates APF features into the SPMC. The focus of this investigation is on the efficiency of alternating current (AC) to direct current (DC) conversion and the reverse process utilizing this advanced UPS model. The SPMC is selected to supplant the rectifier and inverter units traditionally employed in UPS architectures. A novel integrated switching strategy is formulated to facilitate the operation of the UPS in either rectifier (charging) or inverter (discharging) modes, contingent upon the operational state. The performance and efficacy of the devised circuit design and switching technique are substantiated through simulations conducted in MATLAB/Simulink 2019 and empirical evaluations using a test rig. The findings demonstrate that the voltage generated is sinusoidal and synchronized with the supply current, thereby minimizing the total harmonic distortion (THD) and enhancing both the power factor and the transition efficiency of the UPS system between its charging and discharging states.

This paper proposes the design of a compact and highly efficient 2.45 GHz rectifier based on harmonic suppression. The proposed rectifier enhanced the RF–DC efficiency by suppressing the second and third harmonics. Additionally, a second harmonic suppression network was used for matching, thereby eliminating the need for an additional input impedance matching network and resulting in a smaller size. The fabricated rectifier demonstrated a very high power conversion efficiency (PCE) of 81.22 % at an input power of 12.5 dBm, with dimensions of 19 mm×15.5 mm. [ABSTRACT FROM AUTHOR]

This paper proposes a self-supplied power management system to efficiently rectify and regulate the AC voltage received from wireless power transmission techniques to power or recharge biomedical devices. The proposed power management system comprises three integrated functional units, namely, a fully cross-coupled rectifier, a self-biased reference voltage, and a capacitor-less low-dropout regulator (LDO). To reduce the current complexity of designing capacitor-less LDOs, a new architecture based on a pair of diode-connected transistors at the load of the LDO is devised which alleviates the need for a large load capacitor. The proposed power management system is implemented in a 65-nm CMOS process with an active chip area of 0.0810 mm2. Experimental results indicate that this system is capable of rectifying an AC signal up to 5 V at a frequency of 6.78 MHz. This rectified signal is then regulated to a fixed DC voltage of 1.75 V, while the load current can vary between 0 and 75 mA, with a maximum voltage dropout of 170 mV. Advantageously, the proposed power management system is significantly robust to temperature, as a 55 °C change in ambient temperature leads to only a 9% degradation in its overall performance. Furthermore, the ability of the power management system to drive low-power consumer electronics is demonstrated, and its superiority is evidenced by a performance comparison with the latest integrated power management systems presented in the literature. [ABSTRACT FROM AUTHOR]

A hypoglossal nerve stimulator (HGNS) is an invasive device that is used to treat obstructive sleep apnea (OSA) through electrical stimulation. The conventional implantable HGNS device consists of a stimuli generator, a breathing sensor, and electrodes connected to the hypoglossal nerve via leads. However, this implant is bulky and causes significant trauma. In this paper, we propose a minimally invasive HGNS based on an electrocardiogram (ECG) sensor and wireless power transfer (WPT), consisting of a wearable breathing monitor and an implantable stimulator. The breathing external monitor utilizes an ECG sensor to identify abnormal breathing patterns associated with OSA with 88.68% accuracy, achieved through the utilization of a convolutional neural network (CNN) algorithm. With a skin thickness of 5 mm and a receiving coil diameter of 9 mm, the power conversion efficiency was measured as 31.8%. The implantable device, on the other hand, is composed of a front-end CMOS power management module (PMM), a binary-phase-shift-keying (BPSK)-based data demodulator, and a bipolar biphasic current stimuli generator. The PMM, with a silicon area of 0.06 mm 2 (excluding PADs), demonstrated a power conversion efficiency of 77.5% when operating at a receiving frequency of 2 MHz. Furthermore, it offers three-voltage options (1.2 V, 1.8 V, and 3.1 V). Within the data receiver component, a low-power BPSK demodulator was ingeniously incorporated, consuming only 42 μ W when supplied with a voltage of 0.7 V. The performance was achieved through the implementation of the self-biased phase-locked-loop (PLL) technique. The stimuli generator delivers biphasic constant currents, providing a 5 bit programmable range spanning from 0 to 2.4 mA. The functionality of the proposed ECG- and WPT-based HGNS was validated, representing a highly promising solution for the effective management of OSA, all while minimizing the trauma and space requirements. [ABSTRACT FROM AUTHOR]

Traditional current and voltage strategies proposed for the single-phase rectifier with pulse width modulation (PWM) used in the AC charging system for electric vehicles, have a large response time and the percentage of total harmonic distortion (THD) of the line current is more than 2%, which causes a reduction of the power factor (PF). The present paper focuses on the robust sliding mode current–voltage control (SMCVC) design for the single-phase rectifier with PWM. This SMCVC strategy used the grid current directly without any rotating coordinate transformations and reduced the complexity computational of the implementation algorithm and allows to satisfy the following desired performances, low THD of the input current and the PF is around one in a faster response time. In this paper, the proposed control strategy is compared and verified with proportional integral (PI) control and proportional integral sliding mode current control (PI-SMCC) by Matlab/Simulink. At the end of this paper, simulation examples are given to illustrate our approach and to show that our proposed method provides very good results with respect to some literature results. [ABSTRACT FROM AUTHOR]

This paper presents the design and fabrication of a rectenna that receives 2.45 GHz RF signals and converts them into DC power. The rectenna comprises a patch antenna, matching network, and rectifier. It was manufactured and measured using a 0.76-mm thick RF-35A2 board. The matching network was implemented using transmission lines and open stubs and designed to stably convert the RF signal into a fixed DC voltage by employing parallel inductors. The measured rectenna achieved a maximum RF–DC conversion efficiency of 38 % at 2.3-dBm input power and a 1.5-kΩ load. When used in conjunction with the fabricated patch antenna, it transmitted 1.8 V of power at 36 mW into a 90-Ω load at a distance of 10 cm. [ABSTRACT FROM AUTHOR]

This paper presents the results obtained in the design, implementation and testing of a bidirectional CSI (Current source inverter) converter, which is capable of delivering and taking power from the grid to charge a 72 V battery bank. This converter is sized within a photovoltaic solar system designed for homes in the city of Tunja, based on real data to estimate the average consumption of a typical home in the "Cooservicios" sector of the city, proposing two ways of working the system, one to obtain a constant average consumption and another in which the total consumption is zero. The converter is implemented with all its components, digital and power stages, using for the control a TMS 320F28377S microcontroller from C2000 family, of Texas Instruments. The implementation meets specifications of: bidirectional operation as an inverter and as a rectifier, output power of 469 W, efficiency around 80%, highlighting the considerably high value required for the input inductance of 0.3 H that causes losses in the system. [ABSTRACT FROM AUTHOR]

Copyright of Electric Machines & Control / Dianji Yu Kongzhi Xuebao is the property of Electric Machines & Control and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

This paper presents the deployment of a hybrid energy harvesting system that combines a wireless energy harvesting (EH) system and a 6 V, 170 mA monocrystalline solar energy derived from the Sun's rays. The hybrid energy harvesting (HEH) system comprises the rectifier, the solar cell panel, the charging circuit, and the EM4325 embedded RFID tag. This study aims to design an efficient EH system capable of increasing the read range of an active RFID tag. The proposed approach integrates a meandered line radio frequency identification (RFID) tag with an EM4325 IC chip as the receiver antenna. A halfwave doubler RF rectifier circuit is connected to the antenna using a 50 Ω SMA connector to convert the captured RF waves into usable electrical power. A solar energy charging module equipped with a Maximum Power Point Tracking (MPPT) system, a rechargeable lithium-ion battery, and a DC-DC converter is configured to manage and store the harvested energy efficiently. The UHF tag antenna operates at 919 MHz, achieving a peak gain of 3.54 dB. The proposed rectenna achieves a maximum measured harvested power conversion efficiency (PCE) of 55.14% for an input power (Pin) of 15 dBm at a distance of 5.10 cm, while the solar cell panel realizes 3.92 W of power. Experimental results demonstrate the hybrid harvester system's effectiveness, achieving a PCE of 86.49% at an output voltage (VDC) of 5.35 V. The main advantage of this approach is the creation of a compact hybrid RF and solar EH system by combining the solar cell panel with the antenna, thus enabling multi-functionality. [ABSTRACT FROM AUTHOR]

This work designs and implements a single-stage rectifier-based RF energy harvesting device. This device integrates a receiving antenna and a rectifying circuit to convert ambient electromagnetic energy into useful DC power efficiently. The rectenna is carefully engineered with an optimal matching circuit, achieving high efficiency with a return loss of less than −10 dB. The design uses a practical model of the Schottky diode, where both RF and DC characteristics are derived through extensive experimental measurements. The results from both experiments and simulations confirm the effectiveness of the design, showing its proficiency in efficient RF energy harvesting under low-power conditions. The antenna produced operates in the wifi band with a gain close to 4 dBi and a bandwidth of 100 MHz. With a load resistance of 1600 Ω, the proposed device achieves an impressive RF-to-DC conversion efficiency of approximately 52% at a low incident power of −5 dBm. These findings highlight the potential and reliability of rectenna systems for practical and efficient RF energy harvesting applications. The study significantly contributes to our understanding of rectenna-based energy harvesting, providing valuable insights for future design considerations and applications in low-power RF systems.