Search

Abstract This study presents the estimation of the electric and magnetic fields level inside a 400 MVA electrical substation. Located in the northeast region of Brazil, the power plant operates with 230 and 69 kV at 60 Hz frequency. The on‐site measurements were performed at previously selected locations covering the whole courtyard and followed the international and national regulatory standards. The electrical and magnetic fields 2‐D contour maps over the entire courtyard are presented, which allow better visualisation and analysis of the exposure levels around all equipment. By using the GoldenSurfer V.13 tool, eight interpolation methods were applied to predict unsampled locations. The plots were made using the method that best fit the sampled dataset after the cross‐validation technique is used. The measurements were taken during six days during a period of 16 h on 741 locations. For this electrical substation, the maps validate the high electric field level close to breakers and switches at 230 kV and high magnetic field close to equipment operating at 69 kV. The comparison between the exposure levels and those established in current guidelines indicate that the electromagnetic environment on this substation is safe for the occupational population as well as for the general public.

We report a theoretical study of the vortex profile of in-plane magnetized PyTM nano-cylinders subjected to the stray field of perpendicular anisotropy Co nano-cylinders. We consider 6 nm thick PyTM cylinders dipolar coupled to 60 nm thick Co cylinders, at distances from 1.5 nm to 30 nm, with diameters (D) ranging from 45 nm to 105 nm. We find considerable reduction of critical diameter for stable PyTM magnetic vortices and spiral-vortex phases, as well as vortex core diameters twice as large as the bulk value. [ABSTRACT FROM AUTHOR]

Abstract This work aimed to perform the characterization of electrical properties of niobium pentoxide, Nb2O5, pure and doped with molybdenum, prepared by powder metallurgy route and to do a comparative analysis of the influence of this material when sintered in a muffle or in a microwave oven. The results showed that the doping of the niobium pentoxide with 0.5% or 1% of molybdenum along with the process of sintering in a microwave oven make the material more applicable as a microwave absorber material for electromagnetic radiation in the UHF (ultra-high frequency) range between 0.3 to 3 GHz. The motivation of this work was associated with the fact that in Brazil are located two of the largest niobium reserves in the world. Under this view, the study of the processing of the ceramic materials is important considering possible technological applications.

A p-spin interaction Ashkin–Teller spin glass, with three independent Gaussian probability distributions for the exchange interactions, is studied by means of the replica method. A simple phase diagram is obtained within the replica-symmetric approximation, presenting an instability of the paramagnetic solution at low temperatures. The replica-symmetry-breaking procedure is implemented and a rich phase diagram is obtained; besides the paramagnetic phase, three distinct spin-glass phases appear. Three first-order critical frontiers are found and they all meet at a triple point; among such lines, two of them present discontinuities in the order parameters, but no latent heat, whereas the other one exhibits both discontinuities in the order parameters and a finite latent heat. [Copyright &y& Elsevier]

The advancement of embedded technologies has led to increasing demand for bandwidth in telecommunications solutions, this increased the researches related to the architecture of wireless networks and applied electromagnetism. In view of this, the digital transceiver radios need an adequate received signal strength indicator to enable the traffic of information by the radio propagation channel and to provide quality in the data network for the users to exercise the operational activities. The objective of this Letter is to perform the exploratory and variographic analysis of the data collected in the oil fields. Hence, evaluate the behaviour of the surface power distribution received from a wireless system in the frequency range of 5.8 GHz located in the well-automation region called Canto do Amaro, Brazil, where there are frequent communications failures for mobile stations. With the data measured in the measurement campaigns, variogram models were constructed and compared for the construction of interpolation matrices and contour maps, with these results the precision criteria of the kriging methods employed in the study region were established. [ABSTRACT FROM AUTHOR]

The scope of this article is to analyze the trend of the standardized mortality rate (SMR) for tuberculosis and its correlation with the developmental status in Brazil. An ecological time series study was conducted to analyze data of deaths from tuberculosis reported between 2005 and 2019 in all states. Data were extracted from the Mortality Information System, the Brazilian Institute of Geography and Statistics, and the Global Burden of Disease study. The temporal trend was analyzed using Prais-Winsten regression. Spearman's correlation analysis between SMR and Socio-Demographic Index (SDI) was also performed. From 2005 to 2019, 68,879 deaths from tuberculosis were recorded in Brazil. The average mortality rate was 2.3 deaths per 100,000 inhabitants. The decreasing trend of SMR due to tuberculosis was observed in Brazil and in all regions. There was a significant negative correlation between SDI and TMP. TMP due to tuberculosis revealed a decreasing trend in Brazil and in all regions. Most states showed a decreasing trend and none of them had an increasing trend. An inverse relationship was found between developmental status and mortality due to tuberculosis.

Introduction: Myelomeningocele is a severe type of spina bifida, resulting from improper closure of the neural tube. This condition drastically affects the structures of the spinal cord resulting in deficiencies. The combination of these deficiencies results in an overall decrease in mobility and functional participation amongst this population. Physiotherapy plays an essential role in rehabilitating people with MMC. The current literature shows that resources such as photobiomodulation (PBM) may support the rehabilitation of neurological conditions. The aim of the proposed study is to evaluate the effects of photobiomodulation (PBM) combined with physical therapy on functional performance in children with low lumbosacral myelomeningocele., Materials and Methods: This is a protocol randomized clinical blind study, that will include 30 individuals of both sexes, aged between 5 to 8 years, diagnosed with low and sacral lumbar myelomeningocele and capable of performing the sit-to-stand task. The participants will be randomly assigned into two treatment groups: PBM + physiotherapeutic exercises and sham PBM + physiotherapeutic exercises. Irradiation will be carried out with light emitting diode (LED) at a wavelength of 850 nm, energy of 25 J per point, 50 seconds per point and a power of 200 mW. The same device will be used in the placebo group but will not emit light. Muscle activity will be assessed using a portable electromyograph (BTS Engineering) and the sit-to-stand task will be performed as a measure of functioning. Electrodes will be positioned on the lateral gastrocnemius, tibialis anterior and rectus femoris muscles. The Pediatric Evaluation of Disability Inventory will be used to assess functional independence. Quality of life will be assessed using the Child Health Questionnaire-Parent Form 50. Changes in participation will be assessed using the Participation and Environment Measure for Children and Youth. The data will be analyzed with the aid of GraphPad PRISM., Discussion: The results of this study can contribute to a better understanding of the effectiveness of PBM on functioning and quality of life in children with myelomeningocele., Clinical Trial Registration: ClinicalTrials.gov Identifier: NCT04425330., Competing Interests: The authors have declared that no competing interests exist.

Purpose: For carpal tunnel syndrome (CTS), local corticosteroid injection (corticosteroid), and/or wrist immobilization with night orthosis (orthosis) are commonly prescribed and are supported by strong evidence. The aim of this study was to compare orthosis versus corticosteroid for patients with CTS., Methods: A CTS diagnosis was made clinically and supported by electrodiagnostic study. Patients were randomly allocated to either orthosis or corticosteroid. Clinical assessments were performed before the intervention, within the first week of the intervention, and 1, 3, and 6 months after the intervention. Primary outcomes were improvement in nocturnal paresthesia and Boston-Levine questionnaire (BLQ) score. Secondary outcomes were pain assessed by visual analog scale and complications., Results: Of 100 patients enrolled in the study, 95 completed the planned follow-up (45 in the orthosis arm and 50 in the corticosteroid arm). Corticosteroid injections were superior to orthosis in remission of nocturnal paresthesia (remission rates at 1 month, 84.6% versus 43.83%; 3 months, 71.1% versus 40.4%; and 6 months, 80.3% versus 28.8%). The BLQ scores (functional and symptom subscales) were also more favorable for corticosteroid at 1, 3, and 6 months (minimal clinically important differences for Function > 0.5 and Symptom > 0.16). Pain scores were lower and favored the corticosteroid group. There were no complications in either group., Conclusions: Both options are effective in the short term. Corticosteroid is superior to orthosis for improving CTS-related nocturnal paresthesia, BLQ scores, and pain., Type of Study/level of Evidence: Therapeutic I., (Copyright © 2021 American Society for Surgery of the Hand. Published by Elsevier Inc. All rights reserved.)

We report a new polymorph of (1E,4E)-1,5-bis(4-fluorophenyl)penta-1,4-dien-3-one, C 17 H 12 F 2 O. Contrary to the precedent literature polymorph with Z' = 3, our polymorph has one half molecule in the asymmetric unit disordered over two 50% occupancy sites. Each site corresponds to one conformation around the single bond vicinal to the carbonyl group (so-called anti or syn). The other half of the bischalcone is generated by twofold rotation symmetry, giving rise to two half-occupied and overlapping molecules presenting both anti and syn conformations in their open chain. Such a disorder allows for distinct patterns of intermolecular C-H...O contacts involving the carbonyl and anti-oriented β-C-H groups, which is reflected in three 13 C NMR chemical shifts for the carbonyl C atom. Here, we have also assessed the cytotoxicity of three symmetric bischalcones through their in vitro antitumour potential against three cancer cell lines. Cytotoxicity assays revealed that this biological property increases as halogen electronegativity increases.

Introduction: High-resolution magic-angle spinning nuclear magnetic resonance (HR-MAS NMR) spectroscopy enables the analysis of the metabolic profile of plant and animal tissues under close to natural conditions, as well as of other heterogeneous natural or synthetic materials. Neither sample pretreatment is required after fragmentation nor powdering of the sample before insertion into the rotor. However, the efficiency of the method depends strongly on the sample preparation, rotor insertion procedure, and analysis conditions., Objective: To identify some of the variables that affect the spectral data and to propose solutions that minimise their impact on the quality of the analyses and results., Methods: Dried plant tissues were powdered, weighed, and homogenised in a 50 μL rotor with an optimised volume of deuterated solvent and sample in order to prevent material from escaping during spacer insertion, avoiding variations in magnetic susceptibility. Factors affecting the quality of HR-MAS NMR analysis such as particle size, sample and solvent amounts, solvent polarity, swelling time, rotor manipulation and pulse sequence setting were evaluated., Results: A strong correlation was observed between the signal area and the particle size of the powdered sample. The spectral profile varied depending on the deuterated solvent used. An incubation period was necessary to achieve adequate swelling of the sample and to ensure good data reproducibility. Proper sealing of the rotor, number of cycles and τ time on cpmgpr1d pulse sequence were found to affect the signal areas., Conclusion: The study highlights the need for standardised sample preparation and instrumental setup protocols in order to achieve high reproducibility and obtain reliable data from HR-MAS NMR analyses., (© 2018 John Wiley & Sons, Ltd.)

There is evidence that elderly patients with cutaneous leishmaniasis (CL) have more mucosal and disseminated diseases than young patients and their cells produce less antigen-induced interferon (IFN)-γ. Herein, we compared the roles of interleukin (IL)-10 and IL-15 as modulators of antigen-induced immune responses and the incidence of adverse reaction and response to therapy in young versus elderly patients with CL. Study participants included 35 senior (60-85 years) and 35 young (18-40 years) patients who had a diagnosis of CL documented by typical cutaneous lesions containing Leishmania braziliensis DNA. Elderly patients had less lymph node enlargement. Antigen-induced blood cell cytokine responses were studied in the absence or presence of IL-10 antibody or exogenously added recombinant IL-15. The ratio of IFN-γ/IL-10 was lower in elderly patients, and IFN-γ production was enhanced by either neutralization of IL-10 or exogenous recombinant IL-15 in blood cells from elderly but not young patients. Patients were treated three times weekly with antimony at 20 mg/kg/day for 20 doses. Although there was no difference in response to therapy between the two groups, two young patients needed rescue therapy with amphotericin B. Ventricular arrhythmias and ventricular overload were more frequent in elderly patients. We conclude that elderly patients have alterations in the immune response that may influence clinical manifestations, but we did not find that they had a higher failure rate than young subjects to antimony therapy. However, because of the high rate of electrocardiographic abnormalities during therapy, antimony should not be used in elderly patients with CL.

The aim of this study was to evaluate the bond strength between an yttria-stabilized tetragonal zirconia polycrystal (Y-TZP) ceramic and a luting agent when submitted to plasma etching surface treatment before and after thermocycling (TC) with 3000 cycles of 5°C-55°C. The null hypothesis was that the surface treatments and thermocycling would not influence the bond strength. A total of 160 Y-TZP ceramic blocks in 2 sizes (10 size 1 and 10 size 2 blocks in each group) were distributed into 8 groups: group C (control), no surface treatment; group C-TC, TC without prior surface treatment; group SAO, sandblasting with aluminum oxide (Al2O3); group SAO-TC, sandblasting with Al2O3 followed by TC; group SAOS, sandblasting with silica-coated Al2O3; group SAOS-TC, sandblasting with silica-coated Al2O3 followed by TC; group PE, plasma etching; and group PE-TC, plasma etching followed by TC. In each group, size 1 blocks were cemented to size 2 blocks to fabricate specimens for microshear bond strength testing (n = 10 per group). Cementation followed surface treatments (except in control groups) and preceded any TC. All specimens were cemented using a luting agent that contained 10-meth-acryloyloxydecyl dihydrogen phosphate (MDP). The specimens were submitted to a microshear bond strength test and the means were analyzed with a 2-factor analysis of variance and Tukey test. Group PE showed the highest bond strength value before thermocycling (17.31 MPa). After thermocycling, the highest value was observed in the SAO-TC group (9.73 MPa), and statistically significant differences were observed between SAOS-TC and SAO-TC (P < 0.05) and PE-TC and SAO-TC (P < 0.05). Plasma etching improved the bond strength values between the Y-TZP ceramic and MDP-containing luting agent before thermocycling. After thermocycling, all groups showed lower bond strength values., Competing Interests: Disclaimer: The authors report no conflicts of interest pertaining to any of the products or companies discussed in this article.

Rehabilitation with implant-supported prostheses has reached high success rates. However, mechanical failures are still reported, mainly in retention screws of abutments in single implant-supported crowns; which is designed to be the weakest structure and the first component to fail under overloading. In this sense, the aim of this in vitro study was to evaluate the influence of different joint designs (square or hexagonal) on resistance to deformation of driver-retention screw assembly of 3 commercial brands (Neodent, Singular, and Sin). A total of 42 retention screws from 3 commercial brands were used. The samples were divided into 2 joint groups, square (SQU) and hexagonal (HEX), and separated by commercial brands. Several components (implants and abutments) with standard platform (4.1 mm in diameter) were used. The resistance to deformation of the driver-retention screw assembly was measured using an accurate digital torque wrench for all commercial brands (Neodent [NEO], Singular [SGL], and Sin [SIN]) and joint designs (square or hexagonal). It was found no statistically significant difference (P <0.05) among the brands evaluated. On the other hand, square screws showed higher resistance to torsion than hexagonal screws; regardless the commercial brand.

This study evaluated the effect of binder choice in mixing ceramic powder on the chemical and morphological features between the margin ceramic-framework interfaces. Titanium and zirconia frameworks (15 x 5 x 0.5 mm3) were veneered with margin ceramics prepared with two different binders, namely a) water/conventional or b) wax-based. For each zirconia framework material, four different margin ceramics were used: a- Creation Zi (Creation Willi Geller International); b- GC Initial Zr (GC America); Triceram (Dentaurum); and d- IPS emax (voclar Vivadent). For the titanium framework, three different margin ceramics were used: a- Creation Ti (Creation Willi Geller International); b- Triceram (Dentaurum); and c- VITA Titaniumkeramik (Vita Zahnfabrik). The chemical composition of the framework-margin ceramic interface was analyzed using Energy Dispersive X-ray Spectroscopy (EDS) and porosity level was quantified within the margin ceramic using an image program (ImageJ) from four random areas (100 x 100 pixels) on each SEM image. EDS analysis showed the presence of Carbon at the margin ceramic-framework interface in the groups where wax-based binder technique was used with the concentration being the highest for the IPS emax ZirCAD group. While IPS system (IPS ZirCAD and IPS Emax) presented higher porosity concentration using wax binder, in the other groups wax-based binder reduced the porosity of margin ceramic, except for Titanium - Triceram combination.

Purpose: This study evaluated the spatial and functional roughness parameters on air-abraded zirconia as a function of particle type and deposition pressure., Materials and Methods: Polished zirconia blocks (Cercon, Degussa/Dentsply) (N=30) with dimensions of 5 × 4 × 4 mm3 were air abraded according to 2 factors: a) particle type - 30-μm silica-coated alumina (CoJet) or alumina particles (45 μm); b) deposition pressure (1.5, 2.5 and 4.5 bar). Roughness parameters (Sdr, Vi, Sci and Svi) were measured in an optical profilometer (Wyko NT 1100) at the center of the air-abraded area (301.3 × 229.2 μm). Two measurements were made for each parameter from each surface. The means of each group were analyzed by 2-way ANOVA followed by Tukey's adjustment test and Student's t-test (alpha = 0.05)., Results: Both the particle type (p < 0.05) and deposition pressure (p < 0.05) significantly affected the roughness parameters. Interaction terms were significant except for Sci and Svi. With the increase in pressure from 1.5 to 4.5 bar, Sdr (CoJet 1.5: 15.7 ± 0.2; CoJet 4.5: 26.6 ± 0.2; alumina 1.5: 14.7 ± 0.2; alumina 4.5: 24.4 ± 0.2) and Vi (CoJet 1.5: 0.66 ± 0.01; CoJet 4.5: 1.37 ± 0.07; alumina 1.5: 0.62 ± 0.02; alumina 4.5: 1.19 ± 0.02) parameters showed a significant increase with both alumina and CoJet particles. Mean Sci values (CoJet 1.5: 1.62 ± 0.01, CoJet 4.5: 1.49 ± 0.02; alumina 1.5: 1.6 ± 0.03; alumina 4.5: 1.42 ± 0.04) and SVi (CoJet 1.5: 0.98 ± 0.01, CoJet 4.5: 0.112 ± 0.01; alumina 1.5: 0.98 ± 0.01, alumina 4.5: 0.12 ± 0.01) decreased significantly (p < 0.05) with the increase in pressure from 1.5 to 4.5 bar. The pressure increase from 2.5 to 4.5 bar did not cause any significant difference (p > 0.05) in these parameters for either particle type., Conclusion: Considering roughness parameters for micromechanical retention and parameters for adsorption mechanisms of adhesion, zirconia surfaces presented better morphological features when air abraded with silica-coated alumina than alumina particles at pressures higher than 1.5 bar. Particle deposition at 2.5 bar may be preferable to 4.5 bar pressure for avoiding possible deposition-related damage on zirconia, as there were no significant differences for the functional parameters.

Objectives: To determine whether a time delay greater than 6h from injury to surgical debridement influences the infection rate in open fractures., Methods: During a period of 18 months, from October 2010 to March 2012, 151 open fractures were available for study in 142 patients in our hospital. The data were collected prospectively and the patients were followed up for 6 weeks. The patients were divided into two groups regarding the time delay from injury to surgical debridement (more or less than 6 hours)., Results: Surgical debridement was carried out in less than 6h from injury in 90 (59.6%) fractures and after 6 hours from injury in 61 (40.4%) fractures. Infection rates were 12.22% and 13.24%, respectively. The global infection rate was 13.24%., Conclusion: A significantly increased infection rate was not observed in patients whose surgical debridement occurred more than 6h after injury. However, in the fractures of high-energy trauma, a statistically significant increase of the rate of infection was observed in those operated 6 hours after trauma. Level of Evidence II, Study Type Comparative and Prospective.

Objective: To evaluate the factors that influence the survival rate of replantation and revascularization of the thumb and/or fingers., Methods: We included fifty cases treated in our department from May 2012 to October 2013 with total or partial finger amputations, which had blood perfusion deficit and underwent vascular anastomosis. The parameters evaluated were: age, gender, comorbidities, trauma, time and type of ischemia, mechanism, the injured area, number of anastomosed vessels and use of vein grafts. The results were statistically analyzed and type I error value was set at p <0.05 ., Results: Fifty four percent of the 50 performed replantation survived. Of 15 revascularizations performed, the survival rate was 93.3%. The only factor that affected the survival of the amputated limb was the necessity of venous anastomosis., Conclusion: We could not establish contraindications or absolute indications for the replantation and revascularization of finger amputations in this study. Level of Evidence III, Retropective Study.

As part of our continuing chemical and biological analyses of Rubiaceae species from Cerrado, we isolated novel alkaloids 1 and 2, along with known compounds epicatechin, ursolic acid, and oleanolic acid, from Galianthe ramosa. Alkaloid 2 inhibited malate synthase from the pathogenic fungus Paracoccidioides spp. This enzyme is considered an important molecular target because it is not found in humans. Molecular docking simulations were used to describe the interactions between the alkaloids and malate synthase., (Georg Thieme Verlag KG Stuttgart · New York.)

Background: The purpose of this study was to evaluate the relationship between chemokines and dendritic cells (DCs) in human chronic periodontitis (CP)., Methods: Gingival samples were obtained from 23 individuals with CP, and six samples of normal mucosa (NM) overlapping the third molar were used to control for the chemokine levels. Periodontal examination was conducted. Immunohistochemistry was performed for Factor XIIIa(+) and cluster of differentiation (CD)1a(+) immature DCs and CD83(+) mature DCs. Levels of the CC chemokine ligand (CCL)2, CCL3, CCL5, CCL19, CCL20, and CXC chemokine ligand (CXCL)8 were measured in gingival tissues using enzyme-linked immunosorbent assay. Inflammatory infiltrate, DCs, chemokines, classification of human CP, and clinical parameters were correlated and compared., Results: The expression of CCL2 and CCL20 was positively correlated with increased densities of CD1a(+) DCs. CCL3 and CXCL8 were positively related to the clinical attachment level. CCL3, CCL5, CCL19, and CXCL8 levels increased in the gingival samples of patients with CP compared with NM, whereas CCL20 levels increased in advanced CP compared with mild-moderate CP., Conclusions: More CD1a(+) immature DCs are related to CCL2 and CCL20. CCL3 and CXCL8 chemokines are related to a greater severity of human CP.

Purpose: To evaluate the effect of diamond-like carbon (DLC) coating of prefabricated implant abutment on screw removal torque (RT) before and after mechanical cycling (MC)., Materials and Methods: Fifty-four abutments for external-hex implants were divided among 6 groups (n = 9): S, straight abutment (control); SC, straight coated abutment; SCy, straight abutment and MC; SCCy, straight coated abutment and MC; ACy, angled abutment and MC; and ACCy, angled coated abutment and MC. The abutments were attached to the implants by a titanium screw. RT values were measured and registered. Data (in Newton centimeter) were analyzed with analysis of variance and Dunnet test (α = 0.05)., Results: RT values were significantly affected by MC (P = 0.001) and the interaction between DLC coating and MC (P = 0.038). SCy and ACy showed the lowest RT values, statistically different from the control. The abutment coated groups had no statistical difference compared with the control. Scanning electron microscopy analysis showed DLC film with a thickness of 3 μm uniformly coating the hexagonal abutment., Conclusion: DLC film deposited on the abutment can be used as an alternative procedure to reduce abutment screw loosening.

We report the first case of fungemia caused by Paracoccidioides lutzii in a 51-year-old male farm worker from the central-west region of Brazil. The fungus was isolated from blood cultures and the species was confirmed by phylogenetic identification. Despite specific treatment and intensive care, the patient died 39 days after admission., (© The American Society of Tropical Medicine and Hygiene.)

The aim of this study was to evaluate the effect of novel surface treatments of Y-TZP ceramics on initial shear bond strengths to resin cement. Eighty-four samples (7 x 6 x 5 mm) were randomly divided into 6 groups (n=14): Group1 (G1), no treatment; Group 2 (G2), air-borne particle abrasion with silica-coated aluminum oxide particles; Group 3 (G3), vitreous application 1 + etching with hydrofluoric acid; Group 4 (G4), vitreous application 1 + tribosilicatization; Group 5 (G5), vitreous application 2 + etching; Group 6 (G6), vitreous application 2 + tribosilicatization. Surface roughness (Ra) evaluation was performed by optical profilometry, scanning electron microscopy, and X-ray spectroscopy. The samples were silanized, and resin cement cylinders (3 x 2 mm) were built on the treated surfaces, light-cured and submitted to shear testing (1 mm/min). The failure mode was evaluated by SEM. Bond strength data were statistically analyzed using 1-way ANOVA and Tukey's test (α=0.05). Bond strength results were significantly affected by surface treatments (P = 0.0001). G5 and G3 presented increased Ra parameters and showed highest bond strength results (17.8 ± 5.5 and 13.3 ± 4.1, respectively). Failure modes were mainly mixed in all groups except for G1. The results confirmed that the approach of coating surface-conditioned Y-TZP with a vitreous material increased the initial shear bond strength to resin cement.

Objective: The practice of playing musical instruments can affect structures of the head, neck, mouth, and the masticatory system. The aim of this study was to obtain information regarding the prevalence of orofacial pain in musicians according to the type of instrument they play, by applying a specific questionnaire., Materials and Methods: One hundred and seventeen musicians of Sao Paulo state's orchestras participated in this study. They answered an anamnesis questionnaire with 20 questions regarding their personal data, type of instrument played, hours of daily practice, and presence or absence of orofacial pain according to the Chronic Pain Grade Classification (CPGC). Musicians were divided into two groups in accordance with the risk of affecting TMJ: RG (risk group, including violin, viola, vocalist, trombone, tuba, clarinet and saxophone); CG (control group, other instruments). They received an informative brochure about the subject. Data obtained from the questionnaire were submitted to descriptive statistics, Pearson's correlation analysis and Z-test for difference between two proportions., Results: The participants were from 15 to 62 years old. Pain degree showed positive correlation for reported symptoms (P = 0.002) and hour/day practice (P = 0.030). Regarding the prevalence of pain degree, data were, for RG: Grade 0 (54.5%), Grade 1 (30.3%), and Grade ≥2 (15.1%). For CG, Grade 0 (84.4%), Grade 1 (8.9%), and Grade ≥2 (6.6%). Z-test showed positive difference between groups (P = 0.0001)., Conclusion: It was concluded that the musicians of risk group presented higher prevalence of orofacial pain than control (non-risk) group.

Purpose: To evaluate the effect of post-silanization heat treatment of a silane agent and rinsing with hot water of silanized CAD/CAM feldspathic ceramic surfaces on the microtensile bond strength between resin cement and the ceramic, before and after mechanical cycling., Materials and Methods: Blocks measuring 10 x 5.7 x 3.25 mm3 were produced from feldspathic ceramic cubes (VITA Mark II, VITA Zanhfabrik). Each ceramic block was duplicated in composite resin using a template made of polyvinylsiloxane impression material. Afterwards, ceramic and corresponding resin composite blocks were ultrasonically cleaned and randomly divided according to the 5 strategies used for conditioning the ceramic surface (n = 10): GHF: etching with hydrofluoric acid 10% + rinsing with water at room temperature + silanization at 20°C; G20: silanization; G77: silanization + oven drying at 77°C; G20r: silanization + hot water rinsing; G77r: silanization + oven drying at 77°C + hot water rinsing. The resin and ceramic blocks were cemented using a dualcuring resin cement. Every group was divided in two subgroups: aging condition (mechanical cycling, designated as a) or non-aging (designated as n). All the bonded assemblies were sectioned into microsticks for microtensile bond strength (µTBS) testing. The failure mode of the tested specimens was assessed and µTBS data were statistically analyzed in two ways: first 2-way ANOVA (GHF, G20 and G77 in non-aging/aging conditions) and 3-way ANOVA (temperature x rinsing x aging factors, excluding GHF), followed by Tukey's test (p = 0.05)., Results: The 2-way ANOVA revealed that the µTBS was significantly affected by the surface treatment (p < 0.001) but not by aging (p = 0.68), and Tukey's test showed that G77-n/G77-a (18.0 MPa) > GHF-n/GHF-a (12.2 MPa) > G20-n/G20-a (9.1 MPa). The 3-way ANOVA revealed that the µTBS was significantly affected by the "heat treatment" and "rinsing" factors (p < 0.001), but not affected by "aging" (p = 0.36). The rinsing procedure decreased, while oven drying increased the bond strengths. Group G77, in both non-aging and aging conditions (18.6-17.4 MPa), had the highest bond values. Failure modes were mainly mixed for all groups., Conclusion: Oven drying at 77°C improved the bond strength between the resin cement and feldspathic ceramic, but hot water rinsing reduced the bond strength and should not be recommended.

Purpose: The purpose of this study was to evaluate the effect of diamond-like carbon thin films doped and undoped with silver nanoparticles coating poly(methyl methacrylate) (PMMA) on Candida albicans biofilm formation. The control of biofilm formation is important to prevent oral diseases in denture users., Materials and Methods: Forty-five PMMA disks were obtained, finished, cleaned in an ultrasonic bath, and divided into three groups: Gc, no surface coating (control group); Gdlc, coated with diamond-like carbon film; and Gag, coated with diamond-like carbon film doped with silver nanoparticles. The films were deposited using a reactive magnetron sputtering system (physical vapor deposition process). The specimens were characterized by optical profilometry, atomic force microscopy, and Rutherford backscattering spectroscopy analyses that determined differences in chemical composition and morphological structure. Following sterilization of the specimens by γ-ray irradiation, C. albicans (ATCC 18804) biofilms were formed by immersion in 2 ml of Sabouraud dextrose broth inoculated with a standardized fungal suspension. After 24 hours, the number of colony forming units (cfu) per specimen was counted. Data concerning biofilm formation were analyzed using ANOVA and the Tukey test (p < 0.05)., Results: C. albicans biofilm formation was significantly influenced by the films (p < 0.00001), reducing the number of cfu, while not affecting the roughness parameters (p > 0.05). The Tukey test showed no significant difference between Gdlc and Gag. Films deposited were extremely thin (∼50 nm). The silver particles presented a diameter between 60 and 120 nm and regular distribution throughout the film surface (to Gag)., Conclusion: Diamond-like carbon films, doped or undoped with silver nanoparticles, coating the base of PMMA-based dentures could be an alternative procedure for preventing candidosis in denture users., (© 2013 by the American College of Prosthodontists.)

Objective: This study aimed to evaluate the effects of heat treatment on the tribochemical silica coating and silane surface conditioning and the bond strength of rebonded alumina monocrystalline brackets., Material and Methods: Sixty alumina monocrystalline brackets were randomly divided according to adhesive base surface treatments (n=20): Gc, no treatment (control); Gt, tribochemical silica coating + silane application; Gh, as per Gt + post-heat treatment (air flux at 100ºC for 60 s). Brackets were bonded to the enamel premolars surface with a light-polymerized resin and stored in distilled water at 37ºC for 100 days. Additionally, half the specimens of each group were thermocycled (6,000 cycles between 5-55ºC) (TC). The specimens were submitted to the shear bond strength (SBS) test using a universal testing machine (1 mm/min). Failure mode was assessed using optical and scanning electron microscopy (SEM), together with the surface roughness (Ra) of the resin cement in the bracket using interference microscopy (IM). 2-way ANOVA and the Tukey test were used to compare the data (p>0.05)., Results: The strategies used to treat the bracket surface had an effect on the SBS results (p=0.0), but thermocycling did not (p=0.6974). Considering the SBS results (MPa), Gh-TC and Gc showed the highest values (27.59±6.4 and 27.18±2.9) and Gt-TC showed the lowest (8.45±6.7). For the Ra parameter, ANOVA revealed that the aging method had an effect (p=0.0157) but the surface treatments did not (p=0.458). For the thermocycled and non-thermocycled groups, Ra (µm) was 0.69±0.16 and 1.12±0.52, respectively. The most frequent failure mode exhibited was mixed failure involving the enamel-resin-bracket interfaces., Conclusion: Regardless of the aging method, Gh promoted similar SBS results to Gc, suggesting that rebonded ceramic brackets are a more effective strategy.