Search

A film and substrate consisting of poly(ethylene terephthalate) were adhered by means of film‐insert molding. Two injection speeds (i.e., 50 and 500 mm/s) were chosen to induce different shear rates (and molecular orientation) between the film and the substrate. Annealing was subsequently performed on these specimens at different times and temperatures to examine the extent of orientation‐induced crystallization of the substrate surfaces embedded under the film. Differential scanning calorimetry thermograms clearly indicated a shift in the position of the secondary (β) crystalline phase toward a higher temperature in specimens molded at a 500 mm/s injection speed, suggesting that a more densely packed and well‐formed crystalline structure was generated because of higher localized orientation of molecules. Polarized Fourier transform infrared spectroscopy analyses provided dichroic ratios of the 1340‐ and 1410‐cm−1 wavelengths, which corresponded to the trans‐glycol conformer and the stable benzene ring, respectively. Drastic increases in the dichroic ratios were observed, especially in specimens molded at a 500 mm/s injection speed after being annealed for 1 min. This could have been caused by the reorientation of molecules fueled by residual stresses, particularly in regions experiencing high shear during molding. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007 [ABSTRACT FROM AUTHOR]

Electrospinning offers an avenue to produce small diameter tubes made out of nanofibres. However, to date, most tubes from electrospun fibres have been either random fibres or from sheets that were rolled into tubes. Although there have been suggestions of getting tubes made of circumferentially aligned fibres, this is the first time that a method used to create a tube made of diagonally aligned electrospun fibres has been described. This tube was formed by depositing fibres on a rotating tube during electrospinning to give a resultant tube with uniform thickness and superior all round mechanical strength without any line of weakness. A knife-edged auxiliary electrode was given a charge that was opposite to that of the charge given to the needle to create an electrostatic field that encouraged fibre alignment on a rotating tube collector. A tubular structure made of nanofibres aligned in a diagonal direction was produced through electrospinning. [ABSTRACT FROM AUTHOR]

During the COVID-19 pandemic, donor grafts are frequently cryopreserved to ensure that a graft is available before starting a conditioning regimen. However, there have been conflicting reports on the effect of cryopreservation on transplantation outcomes. Also, the impact of cryopreservation may differ in bone marrow (BM) transplantation (BMT) and peripheral blood stem cell (PBSC) transplantation (PBSCT). In this retrospective study, we analyzed the clinical data of both cryopreserved unrelated BMTs (n = 235) and PBSCTs (n = 118) and compared these with data from a large control cohort without cryopreservation including 4133 BMTs and 720 PBSCTs. Among the patients with cryopreserved grafts, 10 BMT recipients (4.3%) and 3 PBSCT recipients (2.5%) did not achieve neutrophil engraftment after transplantation, including 4 of the former and all 3 of the latter who died early before engraftment. In a multivariate analysis, cryopreservation was not associated with neutrophil engraftment in BMT but significantly delayed neutrophil engraftment in PBSCT (hazard ratio [HR], .82; 95% confidence interval [CI], .69 to .97; P = .023). There was an interaction with borderline significance between cryopreservation and the stem cell source (P = .067). Platelet engraftment was delayed by cryopreservation after both BMT and PBSCT. Only 2 cryopreserved grafts (<1%) were unused during the study period. The cryopreservation of unrelated donor BM and PBSC grafts is associated with a slight delay in neutrophil and platelet engraftment but an acceptable rate of graft failure. PBSC grafts may be more sensitive to cryopreservation than BM grafts. Cryopreservation is a reasonable option during COVID-19 pandemic, provided that the apheresis and transplantation centers are adept at cryopreservation. © 2022 American Society for Transplantation and Cellular Therapy. Published by Elsevier Inc., Competing Interests: Conflict of interest statement There are no conflicts of interest to report., (Copyright © 2022 The American Society for Transplantation and Cellular Therapy. Published by Elsevier Inc. All rights reserved.)

During the COVID-19 pandemic, donor hematopoietic stem cell grafts are frequently cryopreserved to ensure the availability of graft before starting a conditioning regimen. However, the safety of cryopreservation has been controversial in unrelated hematopoietic stem cell transplantation (HSCT), especially for bone marrow (BM) grafts. In addition, in unrelated HSCT, the effect of the time from harvest to cryopreservation of donor grafts required for the transportation of donor graft has not been fully clarified. In this study, we retrospectively analyzed the first 112 patients with available data who underwent cryopreserved unrelated blood and marrow transplantation through the Japan Marrow Donor Program during the COVID-19 pandemic. There were 112 patients, including 83 who received BM grafts and 29 who received peripheral blood stem cell (PBSC) grafts. The median time from stem cell harvest to cryopreservation was 9.9 hours (range, 2.6 to 44.0 hours), and the median time from cryopreservation to infusion was 231.2 hours. The incidence of neutrophil engraftment at day 28 after HSCT was 91.1%, and among 109 patients (excluding 3 patients with early death), all but 1 patient achieved neutrophil engraftment within 60 days after HSCT. The time to neutrophil engraftment and time to platelet engraftment were shorter in PBSC transplantation compared with BM transplantation (BMT), but the differences were not statistically significant (P = .064 and .18). Multivariate analysis among BM recipients revealed that a higher number of frozen nucleated cells and the absence of HLA mismatch were associated with faster neutrophil engraftment. The time to neutrophil engraftment after unrelated cryopreserved BMT was not different from that after unrelated BMT without cryopreservation. Our findings suggest that unrelated donor BM and PBSC grafts can be safely cryopreserved even after transit from the harvest center to the transplantation center. In the current COVID-19 pandemic, cryopreservation can be considered as an option while balancing the risks and benefits of the procedure., (Copyright © 2021 The American Society for Transplantation and Cellular Therapy. Published by Elsevier Inc. All rights reserved.)

The interfacial region between nanoparticles and polymer matrix plays a critical role in influencing the mechanical behavior of polymer nanocomposites. In this work, a set of model systems based on poly(methyl methacrylate) (PMMA) matrix containing poly(alkyl glycidyl ether) brushes grafted on 50 nm metal-organic-framework (MOF) nanoparticles were synthesized and investigated. By systematically increasing the polymer brush length and graft density on the MOF nanoparticles, the fracture behavior of PMMA/MOF nanocomposite changes from forming only a few large crazes to generating massive crazing and to undergoing shear banding, which results in significant improvement in fracture toughness. The implication of the present finding for the interfacial design of the nanoparticles for the development of high-performance, multifunctional polymer nanocomposites is discussed.

The impact of using a Novel Tobacco Vapor (NTV) product on indoor air quality (IAQ) was simulated using an environmentally-controlled chamber. Three environmental simulations were examined; two non-smoking areas (conference room and dining room) and one ventilated smoking area (smoking lounge). IAQ was evaluated by (i) measuring constituents in the mainstream NTV product emissions, (ii) and by determining classical environmental tobacco smoke (ETS) and representative air quality markers. Analysis of the mainstream emissions revealed that vapor from the NTV product is chemically simpler than cigarette smoke. ETS markers (RSP, UVPM, FPM, solanesol, nicotine, 3-ethenylpyridine), volatile organic compound (toluene), carbon monoxide, propylene glycol, glycerol, and triacetin were below the limit of detection or the limit of quantification in both the non-smoking and smoking environments after using the NTV product. The concentrations of ammonia, carbonyls (formaldehyde, acetaldehyde, and acetone), and total volatile organic compounds were the same levels found in the chamber without NTV use. There was no significant increase in the levels of formaldehyde, acetone or ammonia in exhaled breath following NTV use. In summary, under the simulations tested, the NTV product had no measurable effect on the IAQ, in either non-smoking or smoking areas., (Copyright © 2017 The Authors. Published by Elsevier Inc. All rights reserved.)

Zeolitic imidazole framework-8 (ZIF-8) is utilized as a functional filler and a curing agent in the preparation of epoxy nanocomposites. The imidazole group on the surface of the ZIF-8 initiates epoxy curing, resulting in covalent bonding between the ZIF-8 crystals and epoxy matrix. A substantial reduction in dielectric constant and increase in tensile modulus were observed. The implication of the present study for utilization of metal-organic framework to improve physical and mechanical properties of polymeric matrixes is discussed.

Poly(3-hexylthiophene) (P3HT) is one of the most promising photovoltaic (PV) polymers in photocurrent therapy. A novel photosensitive scaffold for skin tissue engineering was fabricated by blending P3HT with polycaprolactone (PCL) and electrospun to obtain composite PCL/P3HT nanofibers with three different weight ratios of PCL : P3HT (w/w) of 150 : 2 [PCL/P3HT(2)], 150 : 10 [PCL/P3HT(10)] and 150 : 20 [PCL/P3HT(20)]. The photosensitive properties of the blend solutions and the composite nanofibers of PCL/P3HT were investigated. The incident photon-to-electron conversion efficiencies of the PCL/P3HT(2), PCL/P3HT(10), PCL/P3HT(20) were identified as 2.0 × 10(-6), 1.6 × 10(-5) and 2.9 × 10(-5), respectively, which confirm the photosensitive ability of the P3HT-containing scaffolds. The biocompatibility of the scaffold was evaluated by culturing human dermal fibroblasts and the results showed that the proliferation of HDFs under light stimulation on PCL/P3HT(10) was 12.8%, 11.9%, and 11.6% (p ≤ 0.05) higher than the cell growth on PCL, PCL/P3HT(2) and PCL/P3HT(20), respectively. Human dermal fibroblasts cultured under light stimulation on PCL/P3HT(10) not only showed better cell proliferation but also retained cell morphology similar to the phenotype observed on tissue culture plates (control). Our experimental results suggest novel and potential application of an optimized amount of P3HT-containing scaffold, especially PCL/P3HT(10) nanofibrous scaffold in photocurrent therapy for skin regeneration.

The Drosophila transglutaminase gene (CG7356) encodes two transglutaminases, dTG-A and dTG-B. To understand the roles of dTG-B during the development of the fly, we examined phenotypes induced through ectopic expression of dTG-B. Overexpression of dTG-B induced rough eye and extra wing crossvein phenotypes. These phenotypes were similar to those observed in the case of targeted overexpression of dTG-A.

A reverse-barrier technique is used to enable the treatment of electrospun poly(vinylidene fluoride) nanofibrous membranes with supercritical carbon dioxide. The treatment induces the formation of nanopores and extended-chain β crystallites of small lateral dimensions in the nanofibers. It also creates interfiber junctions, resulting in a remarkable improvement in mechanical properties of the membranes. The treated membranes are able to retain their shape very well after loading with an ionic liquid (IL). The ionic conductivity of the IL-loaded membrane is very close to that of the neat IL., (Copyright © 2010 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.)

Consensus on the taxonomic system and phylogenetic relationships for the anuran genus Fejervarya has yet to be established. Morphological characters in this genus are generally unsuitable for species identification. To carry out molecular species identification and solve phylogenetic problems, we collected 67 Fejervarya specimens from 12 Asian countries and sequenced part of the mitochondrial (mt) Cytb gene. We also sequenced the mt 12S and 16S rRNA genes and seven nuclear genes (BDNF, CXCR4, NCX1, RAG-1, RAG-2, Rhod, and Tyr) for 25 Fejervarya taxa. These molecular markers appear to be adequate for the identification of species. We subjected the molecular data molecular to phylogenetic analyses. In the resulting trees, topotypic F. limnocharis and "F. multistriata" (from China) formed a clade. On the other hand, neither "F. limnocharis" from the Japan mainland nor "F. limnocharis" from eastern Taiwan formed a clade with the real F. limnocharis, and the genetic divergences were larger than the species threshold for frog taxa proposed in previous studies (> 3% for 16S). These results may suggest that "F. multistriata" is a junior synonym of F. limnocharis, or that only some of the populations now recognized as "F. multistriata" correspond to F. limnocharis. Our results also suggest that several cryptic species may be included among the widely distributed Fejervarya species. Finally, our datasets support paraphyly for the genus Fejervarya, although alternative phylogenetic topologies, including Fejervarya monophyly, were not rejected by KH and SH tests.

Poly(L-lactide) (PLLA) and a PLLA/poly(D-lactide) (PDLA) blend (50/50 wt.%) were electrospun into nanofibers. Electron beam (e-beam) irradiation of the electrospun PLLA and blend nanofibers was used as a method to alter their structures and surface properties. The crystalline structures of the nanofibers before and after irradiation were investigated by differential scanning calorimetry. Tensile tests of the aligned nanofibers were also performed to determine the effects of irradiation on the mechanical properties of the nanofibers. The hydrophilicity of the nanofibers was determined by water contact angle measurements, while any degradation of the fibers caused by irradiation could be detected by intrinsic viscosity measurements. The e-beam irradiation method was able to improve the surface hydrophilicity of the PLLA and blend nanofibers, although bulk degradation was inevitable.

Electrospun poly[(R)-3-hydroxybutyrate-co-(R)-3-hydroxyvalerate] (PHBV) fibers were collected by using a counter electrode collector or a rotating disk collector. The molecular orientation and mechanical property of single PHBV fiber were studied. 2-D wide-angle X-ray diffraction and polarized Fourier transform infrared spectra of the macroscopically aligned fibers confirmed the orientation of polymer chains, with PHBV chains preferentially oriented along the fiber axis. The degree of orientation increased with increasing fiber take-up velocity. X-ray diffraction pattern also indicates the development of beta-form crystal in electrospun PHBV fibers collected at an angular velocity of 1500 rpm. The thermal behavior of electrospun PHBV fibers was studied using modulated differential scanning calorimetry. The tensile properties of single electrospun PHBV fibers were studied using a nanotensile tester. Our results indicate that electrospun PHBV fiber with a higher degree of molecular orientation exhibits a higher tensile modulus and strength but lower strain at break.

Polyvinylidene difluoride (PVDF) solutions containing a very low concentration of single-walled carbon nanotubes (SWCNTs) and multiwalled carbon nanotubes (MWCNTs) of similar surface chemistry, respectively, were electrospun, and the nanofibers formed were collected using a modified rotating disk collector. The polymorphic behavior and crystal orientation of the nanofibers were studied using wide-angle X-ray diffraction and infrared spectroscopy, while the nanotube alignment and interfacial interactions in the nanofibers were probed by transmission electron microscopy and Raman spectroscopy. It is shown that the interfacial interaction between the SWCNTs and PVDF and the extensional force experienced by the nanofibers in the electrospinning and collection processes can work synergistically to induce highly oriented beta-form crystallites extensively. In contrast, the MWCNTs could not be well aligned along the nanofiber axis, which leads to a lower degree of crystal orientation.

Electrospinning is widely accepted as a simple and versatile technique for producing nanofibers. The present work, however, introduces a new concept of the electrospinning method for controlling the crystal morphology and molecular orientation of the nanofibers through an illustration of a case study of polyoxymethylene (POM) nanofibers. Isotropic and anisotropic electrospun POM nanofibers are successfully prepared by using a stationary collector and a rotating disk collector. By controlling the voltage and the take-up velocity of the disk rotator, the morphology changes between an extended chain crystal (ECC) and a folded chain crystal (FCC) as clarified by a detailed analysis of the X-ray diffraction and polarized infrared spectra of the POM nanofibers. Herman's orientation function and dichroic ratio lead us to a schematic conclusion--that (i) molecular orientation is parallel to the fiber axis in both isotropic and anisotropic POM nanofibers, (ii) a single nanofiber consists of a nanofibril assembly with a size of 60-70 A and tilting at a certain degree, and (iii) the higher the take-up velocity, the smaller the nanofibril under the (9/5) helical structure of the POM chains. It should be emphasized here that the electrospinning method is no longer a single nanofiber producer but that it can be applied as a new instrument to control the morphology and chain orientation characteristics of polymer materials, opening a new research field in polymer science where we can understand the relationship between structure at the molecular level and the properties and performance at the macroscopic level.

To clarify the genetic divergence in the F. limnocharis complex from Thailand and neighboring countries and to elucidate the phylogenetic problems of this taxon, we analyzed partial sequences of the mitochondrial 12S and 16S rRNA genes and the nuclear CXCR4, NCX1, RAG-1, and tyrosinase genes. The F. limnocharis complex from Thailand had three distinct haplotypes for 12S and 16S rRNA genes. Nucleotide similarities and the phylogenetic relationships indicated that the haplotype 1 group corresponded to the real "F. limnocharis", the haplotype 2 group was F. orissaensis or closely related to it, and the haplotype 3 group was possibly an undescribed species. Mitochondrial gene data also showed two major clades of the genus Fejervarya, the Southeastern and South Asian groups. Although F. orissaensis is so far known only from Orissa in India, the haplotype 2 group was observed in Thailand. This distribution pattern and the phylogeny suggested that the origin of F. orissaensis and the haplotype 2 group might lie in Southeast Asia. There was also evidence suggesting that the haplotype 3 group originated in the South Asian area and has spread to northern Thailand. The nuclear gene data did not support the monophyly of the haplotypes recognized by mitochondrial genes. This incongruence between the mitochondrial and nuclear data seems to be caused by ancestral polymorphic sites contained in nuclear genes. Although neither the mitochondrial nor the nuclear data clarified intergeneric relationships, the nuclear data rejected the monophyly of the genus Fejervarya.

The rice frog (Fejervarya limnocharis) species complex is widely distributed, from India to Japan, and most prevalently in Southeast Asia. Conspicuous morphological variation has been reported for this species complex throughout its distribution range. In the present study, we used mtDNA gene sequence and allozyme analyses to infer evolutionary affinities within this species complex using eight populations (Sri Lanka; Bangkok and Ranong in Thailand; Taiwan; and Hiroshima, Okinawa, Ishigaki and Iriomote in Japan). We also conducted crossing experiments among four populations from Japan, Thailand, and Sri Lanka in order to find out more about the reproductive isolating mechanisms that might exist among the East, Southeast, and South Asian populations of this species complex. The crossing experiments revealed that the Sri Lanka population is reproductively isolated from the Hiroshima, Bangkok, and Ranong populations by complete hybrid inviability, and that the Bangkok population may be reproductively isolated from the Hiroshima population by partial hybrid inviability. Thus, it is not unreasonable to regard the Sri Lanka population as a species separated from F. limnocharis. The mtDNA and allozyme data showed that the Ranong population is most closely related to the Bangkok population in nuclear genome, but more similar to the Okinawa and Taiwan populations in mtDNA genome. The present, preliminary survey may raise questions about the species status of these particular populations and also about the nature of the biological species concept.

Conducting polymers were electrospun into fibers with other spinnable polymers. The optical properties of the electrospun fibers were characterized in comparison with spin-cast thin films. The electrospun conducting polymer-based fibers with different fiber diameters of 100 nm and 1 microm were prepared. Aligned nanofibers were prepared using a rotating disc collector in order to induce molecular orientation in the electrospun fibers. The effect of electrospinning processes on the optical properties was discussed in terms of fiber diameter and molecular orientation.

Polypropylene (PP)/clay nanocomposites have been prepared via a reactive compounding approach with an epoxy based masterbatch. Compared with PP and common PP/organoclay nanocomposites, the PP/clay nanocomposites based on epoxy/clay masterbatch have higher impact strength. The phenomenon can be attributed to the epoxy phase dispersed uniformly in the PP matrix, which may act as impact energy absorber and helps to form a large damage zone, thus a higher impact strength value is achieved.

In this study, new type of guided bone regeneration (GBR) membranes were fabricated by polycaprolactone (PCL)/CaCO3 composite nano-fibers with two different PCL to calcium carbonate (CaCO3) ratios (PCL:CaCO3=75:25 wt% and 25:75 wt%). The composite nano-fibers were successfully fabricated by electrospinning method and CaCO3 nano-particles on the surface of nano-fibers were confirmed by energy disperse X-ray (EDX) analysis. In order to achieve mechanical stability of GBR membranes, composite nano-fibers were spun on PCL nano-fibrous membranes which has high tensile strength, i.e., the membranes consist of two layers of functional layer (PCL/CaCO3) and mechanical support layer (PCL). Two different GBR membranes were prepared, i.e., GBR membrane (A)=PCL:CaCO3=75:25 wt%+PCL, GBR membrane (B)=PCL:CaCO3=25:75 wt%+PCL. Osteoblast attachment and proliferation of GBR membrane (A) and (B) were discussed by MTS assay and scanning electron microscope (SEM) observation. As a result, absorbance intensity of GBR membrane (A) and tissue culture polystyrene (TCPS) increased during 5 days seeding time. In contrast, although absorbance intensity of GBR membrane (B) also increased, its value was lower than membrane (A). SEM observation showed that no significant difference in osteoblast attachment manner was seen on GBR membrane (A) and (B). Because of good cell attachment manner, there is a potential to utilize PCL/CaCO3 composite nano-fibers to GBR membranes.

Non-woven polyethylene terephthalate nanofiber mats (PET NFM) were prepared by electrospinning technology and were surface modified to mimic the fibrous proteins in native extracellular matrix towards constructing a biocompatible surface for endothelial cells (ECs). The electrospun PET NFM was first treated in formaldehyde to yield hydroxyl groups on the surface, followed by the grafting polymerization of methacrylic acid (MAA) initiated by Ce(IV). Finally, the PMAA-grafted PET NFM was grafted with gelatin using water-soluble carbodiimide as coupling agent. Plane PET film was also surface modified and characterized for basic understanding of the surface modification process. The grafting of PMAA and gelatin on PET surface was confirmed by XPS spectroscopy and quantitatively analyzed by colorimetric methods. ECs were cultured on the original and gelatin-modified PET NFM and the cell morphology, proliferation and viability were studied. Three characteristic surface makers expressed by ECs were studied using immuno-florescent microscopy. The gelatin grafting method can obviously improve the spreading and proliferation of the ECs on the PET NFM, and moreover, can preserve the EC's phenotype.

An electrospinning method was used to spin semi-crystalline poly(L-lactide) (PLLA) nanofibres. Processing parameter effects on the internal molecular structure of electrospun PLLA fibres were investigated by x-ray diffraction (XRD) and differential scanning calorimetry (DSC). Take-up velocity was found as a dominant parameter to induce a highly ordered molecular structure in the electrospun PLLA fibres compared to solution conductivity and polymer concentration, although these two parameters played an important role in controlling the fibre diameter. A collecting method of a single nanofibre by an electrospinning process was developed for the tensile tests to investigate structure-property relationships of the polymer nanofibres. The tensile test results indicated that higher take-up velocity caused higher tensile modulus and strength due to the ordered structure developed through the process.

Tissue-engineering scaffolds should be analogous to native extracellular matrix (ECM) in terms of both chemical composition and physical structure. Polymeric nanofiber matrix is similar, with its nanoscaled nonwoven fibrous ECM proteins, and thus is a candidate ECM-mimetic material. Techniques such as electrospinning to produce polymeric nanofibers have stimulated researchers to explore the application of nanofiber matrix as a tissue-engineering scaffold. This review covers the preparation and modification of polymeric nanofiber matrix in the development of future tissue-engineering scaffolds. Major emphasis is also given to the development and applications of aligned, core shell-structured, or surface-functionalized polymer nanofibers. The potential application of polymer nanofibers extends far beyond tissue engineering. Owing to their high surface area, functionalized polymer nanofibers will find broad applications as drug delivery carriers, biosensors, and molecular filtration membranes in future.

Substantial effort is being invested by the bioengineering community to develop biodegradable polymer scaffolds suitable for tissue-engineering applications. An ideal scaffold should mimic the structural and purposeful profile of materials found in the natural extracellular matrix (ECM) architecture. To accomplish this goal, poly (L-lactide-co-epsilon-caprolactone) [P(LLA-CL)] (75:25) copolymer with a novel architecture produced by an electrospinning process has been developed for tissue-engineering applications. The diameter of this electrospun P(LLA-CL) fiber ranges from 400 to 800 nm, which mimicks the nanoscale dimension of native ECM. The mechanical properties of this structure are comparable to those of human coronary artery. To evaluate the feasibility of using this nanofibrous scaffold as a synthetic extracellular matrix for culturing human smooth muscle cells and endothelial cells, these two types of cells were seeded on the scaffold for 7 days. The data from scanning electron microscopy, immunohistochemical examination, laser scanning confocal microscopy, and a cell proliferation assay suggested that this electrospun nanofibrous scaffold is capable of supporting cell attachment and proliferation. Smooth muscle cells and endothelial cells seeded on this scaffold tend to maintain their phenotypic shape. They were also found to integrate with the nanofibers to form a three-dimensional cellular network. These results indicate a favorable interaction between this synthetic nanofibrous scaffold with the two types of cells and suggest its potential application in tissue engineering a blood vessel substitute.