Search

PURPOSE: The aim of this ex vivo study was to assess the ability to remove oral biofilm by different combinations of mechanical and chemical treatments on smooth and rough titanium surfaces, as well as their impact on osteoconduction. MATERIALS AND METHODS: Forty-eight sandblasted acid-etched (SLA) and 48 machined titanium disks were contaminated with oral bacterial biofilm and exposed to the following treatments: (1) titanium brush (TB), (2) TB + 40% citric acid (CA), (3) TB + 5.25% sodium hypochlorite (NaOCl), (4) air polishing with glycine powder (AP), (5) AP + 40% CA, and (6) AP + 5.25% NaOCl. Residual bacteria and chemical contamination were assessed using viable bacterial count assay, scanning electron microscopy (SEM), and x-ray spectroscopy (XPS). Human primary osteoblast (hOB) adhesion and osteocalcin (OC) release were also evaluated. RESULTS: The microbiologic, SEM, and XPS analysis indicate a higher biofilm removal efficiency of combined mechanical-chemical treatments compared with exclusively mechanical approaches, especially on SLA surfaces. SEM analysis revealed significant alterations of surface microtopography on the disks treated with TB, while no changes were observed after AP treatment. OC release by hOBs was mainly decreased on disks treated with CA and NaOCl. CONCLUSION: The combination of mechanical and chemical treatments provides effective oral biofilm removal on both SLA and machined implant surfaces. NaOCl and CA may have a negative effect on osteoblasts cultured on SLA samples.

Implant stability is influenced by bone density, implant design, and site preparation characteristics. Piezoelectric implant site preparation (PISP) has been demonstrated to improve secondary stability compared with conventional drilling techniques. Osseodensification drills (OD) have been recently introduced to enhance both bone density and implant secondary stability. The objective of the present multi-center prospective randomized controlled trial was to monitor implant stability changes over the first 90 days of healing after implant bed preparation with OD or PISP.Each patient received two identical, adjacent or contralateral implants in the posterior maxilla. Following randomization, test sites were prepared with OD and control sites with PISP. Resonance frequency analysis was performed immediately after implant placement and after 7, 14, 21, 28, 60, and 90 days. Implants were then restored with single screw-retained metal-ceramic crowns and followed for 12 months after loading.Twenty-seven patients (15 males and 12 females; mean age 63.0 ± 11.8 years) were included in final analysis. Each patient received two identical implants in the posterior maxilla (total = 54 implants). After 1 year of loading, 53 implants were satisfactorily in function (one failure in test group 28 days after placement). Mean peak insertion torque (40.7 ± 12.3 Ncm and 39.5 ± 10.2 Ncm in test and control group, respectively) and mean implant stability quotient (ISQ) value at baseline (71.3 ± 6.9 and 69.3 ± 7.6 in test and control group, respectively) showed no significant differences between the two groups. After an initial slight stability decrease, a shift to increasing ISQ values occurred after 14 days in control group and after 21 days in test group, but with no significant differences in ISQ values between the two groups during the first 90 days of healing.No significant differences in either primary or secondary stability or implant survival rate after 1 year of loading were demonstrated between implants inserted into sites prepared with OD and PISP.

Purpose To investigate clinical and radiographic outcomes of transcrestal maxillary sinus floor elevation performed with an injectable xenograft in gel form, analyzing general, local and surgical variables possibly influencing the results. Methods Patients with residual crestal height Results 71 patients underwent transcrestal sinus floor elevation and 54 implants were simultaneously placed. Delayed implant placement (at T1) was possible in 5 cases out of 17 (29.4%), whereas in 12 patients (70.6%) implant insertion was not possible or required additional sinus grafting. Implant survival rate, with a follow-up varying from 12 to 32 months after loading, was 100%. Mean pre-operative bone height was 3.8 ± 1.0 mm, at T0 was 13.9 ± 2.2 mm and at T1 was 9.9 ± 2.8 mm. Bone height at T1 was negatively influenced by membrane perforation at surgery (p = 0.004) and positively influenced by immediate implant insertion (p Conclusions Transcrestal sinus floor elevation performed with injectable xenograft gel resulted in 100% implant survival rate. However, immediate implant insertion seems a crucial factor to preserve vertical bone gain: one-stage technique seems to be the most predictable approach to optimize clinical outcomes with this approach. Trial registration clinicaltrials.gov, NCT05305521. Registered 31 March 2022—Retrospectively registered, https://clinicaltrials.gov/ct2/show/NCT05305521.

Leukocyte- and platelet-rich fibrin (L-PRF) is an autologous platelet concentrate rich in growth factors and plasma proteins, obtained by centrifugation of patient whole blood, and widely used in oral surgery. This report describes a case of alveolar ridge preservation with L-PRF membranes. Postextractive alveolar healing was then assessed through a histologic and histomorphometric analysis. A patient requiring tooth extraction and subsequent implant rehabilitation was treated with simple extraction and socket filling with L-PRF membranes. Implant placement was performed at 3 months, and a bone biopsy was obtained for histomorphometric analysis. Histological examination of the grafted sites showed that the use of L-PRF could achieve good results in terms of bone dimension and quality and soft tissue healing. The results of this study support the use of L-PRF membranes to preserve hard and soft tissues after tooth extraction.

This article was published in volume 69, issue 1 of publishing year 2020, with the wrong Figure 1. The correct Figure 1 is the one included in this erratum.

Background. The aim of this study was to compare retrospectively the effect of three different treatment protocols on the healing outcome in patients with established medication-related osteonecrosis of the jaw (MRONJ). Methods. A total of 34 MRONJ patients were recruited from the Department database and were divided according to the treatment protocols in a study group (G1) and two control groups (G2 and G3). G1 was treated with antibiotic therapy, surgery, leukocyte- and platelet-rich fibrin (L-PRF), and photobiomodulation, G2 was treated with antibiotic therapy and surgery, G3 was treated with antibiotic therapy and photobiomodulation. Various clinical variables and treatment protocols were analyzed to determine their correlation with the healing outcome at three and six months of follow-up. Results. There was a significant association between the different treatment protocols and the outcomes at both three and six months follow-up (p = 0.001 and p = 0.002, respectively). No significant association was observed between the outcomes and MRONJ localization, MRONJ stage, duration of drug treatment, gender, diabetes, corticosteroid therapy, smoking habits, underlying disease, and history of chemotherapy at both three and six months follow-up. Conclusions. Our results show that the combination of antibiotic therapy, surgery, L-PRF, and photobiomodulation may effectively contribute to MRONJ management.

Liquid fibrinogen is an injectable platelet concentrate rich in platelets, leukocytes, and fibrinogen obtained by blood centrifugation. The aim of this study was to analyze the release of different growth factors in the liquid fibrinogen at different times and to assess possible correlations between growth factors and cell counts. The concentration of transforming growth factor beta 1 (TGF-&beta, 1), platelet-derived growth factor-AB (PDGF-AB), platelet-derived growth factor-BB (PDGF-BB), bone morphogenetic protein 2 (BMP-2), fibroblast growth factor 2 (FGF-2) and vascular endothelial growth factor (VEGF) released by liquid fibrinogen were examined with ELISA at three time points (T0, time of collection, T7, 7 days, T14, 14 days). The cellular content of the liquid fibrinogen and whole blood was also calculated for each volunteer. A mean accumulation of platelets of almost 1.5-fold in liquid fibrinogen compared to whole blood samples was found. An increase of TGF-&beta, 1, PDGF-AB, FGF-2, and VEGF levels was detected at T7. At T14, the level of TGF-&beta, 1 returned to T0 level, PDGF-AB amount remained high, the levels of FGF-2 and VEGF decreased with respect to T7, but remained higher than the T0 levels, PDGF-BB was high at all time points, BMP-2 level was low and remained constant at all time points. TGF-&beta, 1, PDGF-AB, and PDGF-BB showed a correlation with platelet amount, whereas BMP-2, FGF-2, and VEGF showed a mild correlation with platelet amount. Due to the high concentration of platelets, liquid fibrinogen does contain important growth factors for the regeneration of both soft and hard tissue. The centrifugation protocol tested in this study provides a valid solution to stimulate wound healing in oral and periodontal surgery.

The aim of this study was to review the histologic evidence of reosseointegration and related influencing factors in experimental induced peri-implantitis.An electronic search was performed on Medline for animal studies that included a histometric evaluation of the amount of regenerated bone in contact with an implant surface. Questions raised in the study focused on the role of implant surfaces, bone regeneration and decontamination treatments in achieving reosseointegration. A detailed electronic search was then conducted on MEDLINE (PubMed) up to July 2017.One hundred and one articles were selected as abstract, thirty-seven articles assessed as full-text and sixteen finally included in the study. Reported measurements of reosseointegration varied significantly in the study, from 0 to 3.37 mm. There is histological evidence that reosseointegration can occur after treatment of ligature-induced peri-implantitis. However regenerated bone in contact with bone is generally restricted to the most apical portion of the peri-implant defect.Animal studies of induced peri-implantitis seem to indicate that rough surfaces can enhance reosseointegration as compared to smooth surfaces. With regard to bone regeneration techniques and materials, submerged healing and barrier membranes have shown a positive effect on reosseointegration. No evidence exists, however, about the specific role of different bone substitutes and their ability to improve bone formation. Growth factors have been shown to improve reosseointegration in animal models, though additional study is required to confirm the data. Several decontamination treatments have been shown to promote reosseointegration compared to control; however no specific procedure has proven superior to others in achieving reosseointegration.

Several antiseptic agents have been proposed for the treatment of peri-implantitis as a complementary therapeutic strategy in addition to mechanical devices. The aim of this study was to compare six different antiseptics, as well as alternative formulations of the same chemical agent, with respect to their decontamination efficacy and impact on chemical properties of the implant surface. Titanium disks with a micro-rough surface, previously contaminated with Porphyromonas gingivalis and Streptococcus mutans biofilms, were treated for 2 min with different antiseptics (liquid sodium hypochlorite 5.25%, gel sodium hypochlorite 5.25%, liquid chlorhexidine 0.2%, gel chlorhexidine 1%, gel citric acid 40%, and gel orthophosphoric acid 37%) or sterile saline solution (control) and their antibacterial activity as well as their ability to remove biofilm were assessed by viable bacterial count and scanning electron microscopy, respectively. Spectroscopic analysis was also performed on non-contaminated disks after exposure to the antiseptics, in order to detect any change in the elemental composition of the titanium surface. All the antimicrobial formulations examined were effective against P. gingivalis and S. mutans biofilms. SEM analysis revealed however that liquid sodium hypochlorite 5.25% was more effective in dissolving biofilm residues. Spectroscopic analysis detected traces of the antiseptics, probably due to insufficient rinsing of the titanium surfaces. In conclusion, since gel formulations of these antiseptic agents possessed a similar antibacterial activity to the liquid formulations, these may be proposed as alternative treatments given their properties to avoid overflows and increase contact time without significant side effects on the bone.

Purpose: To assess and compare topographic features and preosteoblastic cell responses of a new hydrothermally treated, calcium-incorporated surface against other commercially available implant surfaces. Materials and Methods: Four different surfaces were the subject of comparison in this study: machined (MC), resorbable blast media (RBM), sandblasted/large-grit/acid-etched (SLA), and calcium-incorporated SLA (Ca-SLA). Surface morphology and roughness were first characterized by scanning electron microscope (SEM) and white light interferometer, respectively. Preosteoblastic MC3T3-E1 cells were then cultured on the titanium surfaces. Cell morphology was observed at 24 hours, 48 hours, 7 days, and 15 days by SEM; differentiation was assessed at 7, 11, and 15 days by assaying alkaline phosphatase (ALP) activity and osteocalcin (OCN) levels. Results: Surface characterization revealed nanotopographic features on Ca-SLA. At topographic analysis, SLA and Ca-SLA showed similar roughness values. Significant differences in cell differentiation parameters were found only at 15 days between the SLA surfaces (both Ca-incorporated and nonincorporated) and MC. Conclusion: Collectively, this study demonstrated that hydrothermal treatment determines the formation of nanotopography without altering the SLA microtopography. Moreover, Ca-SLA and SLA induce MC3T3-E1 cell differentiation at comparable levels.

Piezoelectric devices are widely used in oral surgical procedures, including implant site preparation. However, little is known about the influence of working movement on temperature elevation in bone. The aim of this study was to assess the effects of two different working cycles on temperature elevation during piezoelectric implant site preparation. Sixty osteotomies at a depth of 10 mm were performed on bone blocks of bovine ribs using a piezoelectric tip with external irrigation (IM1s, Mectron Medical Technology, Carasco, Italy). A mechanical positioning device was used to guarantee reproducible working and measuring conditions. Two different working cycles, of 4 and 6 s, respectively, were tested, including both longitudinal and rotational movements. Temperature was recorded in real time with a fiber optic thermometer and applied pressure was maintained under 150 g. For each test, the highest recorded temperature (Tmax) and the mean temperature recorded from 30 s before to 30 s after the highest recorded temperature (T&plusmn, 30) were extrapolated. Tests duration was also recorded. Both Tmax and T&plusmn, 30 were significantly higher in the &lsquo, 6 s cycles&rsquo, group than the &lsquo, 4 s cycles&rsquo, group (42.44 &plusmn, 7.3 &deg, C vs. 37.24 &plusmn, 4.6 &deg, C, p = 0.002, 37.24 &plusmn, C vs. 33.30 &plusmn, 3.3 &deg, C, p = 0.003). Test duration was also significantly higher using 6 s cycles compared to 4 s cycles (143.17 &plusmn, 29.4 s vs. 119.80 &plusmn, 36.4 s, p = 0.002). The results of this study indicate that working cycles of 4 s effectively reduce heat generation and working time during piezoelectric implant site preparation.

Alveolar ridge preservation has become a very common procedure following tooth extraction. This study presents a clinical, histologic, and histomorphometric analysis of postextraction bone changes using nanocrystalline hydroxyapatite (nc-HA) and exposed high-density polytetrafluoroethylene (d-PTFE) membrane. A total of 10 extraction sockets were treated. Clinical measurements were taken after tooth extraction with a customized acrylic stent to ensure the same measurement points. At 6 months, clinical measurements were repeated and bone specimens taken. An overall bone reduction was observed. The histologic and histomorphometric analysis revealed newly formed bone (25.92% ± 18.78%), soft tissue (28.55% ± 9.73%), and residual graft particles (15.43% ± 11.08%). Further studies are necessary to evaluate the efficacy of this technique over the long term.

Purpose. Various parameters can influence temperature rise and detection during implant site preparation. The aim of this study is to investigate local temperature values in cortical and corticocancellous bovine bone during early stages of piezoelectric implant site preparation.Materials and Methods. 20 osteotomies were performed using a diamond tip (IM1s, Mectron Medical Technology, Carasco, Italy) on two different types of bovine bone samples, cortical and corticocancellous, respectively. A standardized protocol was designed to provide constant working conditions. Temperatures were measured in real time at a fixed position by a fiber optic thermometer.Results. Significantly higher drilling time (154.90 sec versus 99.00 sec;p<0.0001) and temperatures (39.26°C versus 34.73°C;p=0.043) were observed in the cortical group compared to the corticocancellous group. A remarkable variability of results characterized the corticocancellous blocks as compared to the blocks of pure cortical bone.Conclusion. Bone samples can influence heat generation duringin vitroimplant site preparation. When compared to cortical bone, corticocancellous samples present more variability in temperature values. Even controlling most experimental factors, the impact of bone samples still remains one of the main causes of temperature variability.

This study aimed to evaluate the efficacy of an exposed high-density polytetrafluoroethylene (d-PTFE) membrane in preventing epithelial migration in postextraction sockets. For this purpose, a histologic description of the newly formed soft tissue underlying the membrane is presented. The periodontal status of the adjacent teeth was also evaluated to assess the gingival response. Ten premolar extraction sockets were treated. After tooth extraction, the sockets were filled with nanocrystalline hydroxyapatite and covered with d-PTFE membranes. Subperiosteal pockets were created to ensure the stability of the membranes. Membranes were left intentionally exposed and were atraumatically removed after 28 days. At that time, a bioptic specimen of the newly formed soft tissue under the membranes was taken. All the histologic samples showed a dense connective tissue without epithelial cells and no signs of foreign body reaction. No significant variation of the periodontal indices was observed on the teeth adjacent to the extraction sites. The study results indicate that exposed d-PTFE membranes can prevent epithelial migration in healing sockets without consequences on the periodontal health.

Psoriatic arthritis (PsA) is a chronic inflammatory disease of the skin and joints characterized by extensive intra-articular bone resorption and silver-red scaly plaques most commonly found on extensor surfaces of the skin. When this arthritis affects the temporomandibular joint (TMJ) and does not successfully halt in its early degenerative process, patients may undergo invasive joint reconstruction that irreversibly changes the TMJ physiologic joint dynamics. This study presents a case of TMJ PsA: anterior open bite, limited range of motion, and erythematous desquamative plaques of the upper limb extensors surfaces. The patient previously received non-steroidal anti-inflammatory drugs, immunosuppressors, and corticosteroids over a four-year period while suffering the idiosyncratic drug side effects from long-term therapy without improvement in joint function or rash resolution. The treatment team then chose etanercept, a synthetic fusion protein therapy that binds with tumor necrosis factor (TNF)-alpha, to interrupt reactive inflammatory arthritis. The patient received the TNF-alpha inhibitor monthly for two years. This last treatment led to full remission of both joint symptomatology and skin lesions. Our results should encourage general dental practitioners' involvement in curing patients with psoriatic arthritis when it affects the TMJ.

Overheating during implant site preparation negatively affects the osseointegration process as well the final outcome of implant rehabilitations. Piezoelectric techniques seem to provide to a gentle implant preparation although few scientific reports have investigated the heat generation and its underlying factors. To investigate, through a proper methodological approach, the main factors influencing temperature rise during piezoelectric implant site preparation. Different piezoelectric tips (IM1s, IM2, P2-3, IM3, Mectron Medical Technology, Carasco, Italy) have been tested. The experimental set-up consisted in a mechanical positioning device equipped with a load cell and a fluoroptic thermometer. The first tip of the sequence (IM1s) generated the highest temperature increasing (ΔT). The diamond tips (IM1s and P2-3) determined higher ΔT values than the smooth tips (IM2 and IM3). Further tests with IM1s suggested that the temperature elevation during the first thirty seconds may be predictive of the maximal temperature as well as of the overall thermal impact. Working load, working movements management and bone features resulted to be the main factors influencing temperature rise during piezoelectric implant site preparation. Irrigant temperature and clogging effect may also synergically contribute to the heat generation.

Craniometaphyseal dysplasia (CMD) is a rare genetically transmitted bone dysplasia characterized by alterations in the development of the craniofacial bones with abnormal remodeling of the metaphyses. Sclerosis of the skull bones can lead to cranial nerve compression that finally may result in hearing loss and facial palsy. CMD occurs in an autosomal dominant (AD) (MIM 123000) and an autosomal recessive (AR) form (MIM 218400). Sclerosis of cranial bones is usually much more severe in the AR form. We present a 36-year-old male with a previous diagnosis of Paget disease. The examination reveals prognathism, ocular hypertelorism, mixed bilateral hypoacusia, nasal bossing, a class III malocclusion and a narrow palatal vault. The patient necessitated several dental extractions, surgical procedures were conducted, and a biopsy of the alveolus was performed and the sample underwent histological examination. The histological report led to an exclusion of the previous diagnosis of Paget disease. The final diagnosis of autosomal dominant CMD was confirmed by the molecular testing of the CMD gene (ANKH).