Search

Rutile GeO$_2$ is a promising ultra-wide bandgap semiconductor for future power electronic devices whose alloy with the wide bandgap semiconductor rutile-SnO$_2$ enables bandgap engineering and the formation of heterostructure devices. The (Sn$_x$Ge$_{1-x}$)O$_2$ alloy system is in its infancy and molecular beam epitaxy (MBE) is a well-suited technique for its thin-film growth, yet presents challenges in controlling the alloy composition and growth rate. To understand and mitigate this challenge, the present study comprehensively investigates the kinetics and thermodynamics of suboxide incorporation into GeO$_2$, SnO$_2$, and (Sn$_x$Ge$_{1-x}$)O$_2$ during suboxide MBE, the latest development in oxide MBE using suboxide sources. We find suboxide MBE to simplify the growth kinetics, offering better control over growth rates than conventional MBE but without supporting cation-driven oxide layer etching. During binary growth, SnO incorporation is kinetically favored due to its higher oxidation efficiency and lower vapor pressure compared to those of GeO. In (Sn$_x$Ge$_{1-x}$)O$_2$ growth, however, the GeO incorporation is preferred and the SnO incorporation is suppressed, indicating a catalytic effect, where SnO promotes GeO incorporation through cation exchange. The origin of this cation exchange is likely thermodynamic yet calls for further theoretical studies. Our experimental study provides guidance for controlling the growth rate and alloy composition of (Sn$_x$Ge$_{1-x}$)O$_2$ in suboxide MBE, highlighting the impact of the substrate temperature and active oxygen flux besides that of the mere SnO:GeO flux stoichiometry. The results are likely transferable to further physical and chemical vapor deposition methods, such as conventional and hybrid MBE, pulsed laser deposition, mist- or metalorganic chemical vapor deposition.

500-nm-thick $\mathrm{In}_{x}\mathrm{Ga}_{1-x}\mathrm{N}$ layers with $x=$ 0.05-0.14 are grown using plasma-assisted molecular beam epitaxy, and their properties are assessed by a comprehensive analysis involving x-ray diffraction, secondary ion mass spectrometry, and cathodoluminescence as well as photoluminescence spectroscopy. We demonstrate low degrees of strain relaxation (10% for $x=0.12$), low threading dislocation densities ($\mathrm{1\times10^{9}\,cm^{-2}}$ for $x=0.12$), uniform composition both in the growth and lateral direction, and a narrow emission band. The unique sum of excellent materials properties make these layers an attractive basis for the top-down fabrication of ternary nanowires.

The dewetting of thin Pt films on different surfaces is investigated as a means to provide the patterning for the top-down fabrication of GaN nanowire ensembles. The transformation from a thin film to an ensemble of nanoislands upon annealing proceeds in good agreement with the void growth model. With increasing annealing duration, the size and shape uniformity of the nanoislands improves. This improvement speeds up for higher annealing temperature. After an optimum annealing duration, the size uniformity deteriorates due to the coalescence of neighboring islands. By changing the Pt film thickness, the nanoisland diameter and density can be quantitatively controlled in a way predicted by a simple thermodynamic model. We demonstrate the uniformity of the nanoisland ensembles for an area larger than 1 cm$^2$. GaN nanowires are fabricated by a sequence of dry and wet etching steps, and these nanowires inherit the diameters and density of the Pt nanoisland ensemble used as a mask. Our study achieves advancements in size uniformity and range of obtainable diameters compared to previous works. This simple, economical, and scalable approach to the top-down fabrication of nanowires is useful for applications requiring large and uniform nanowire ensembles with controllable dimensions.

We study the molecular beam epitaxy of rock-salt ScN on the wurtzite GaN($1\bar{1}00$) surface. To this end, ScN is grown on free-standing GaN($1\bar{1}00$) substrates and self-assembled GaN nanowires that exhibit ($1\bar{1}00$) sidewalls. On both substrates, ScN crystallizes twin-free thanks to a specific epitaxial relationship, namely ScN(110)[001]$||$GaN($1\bar{1}00$)[0001], providing a congruent, low-symmetry GaN/ScN interface. The 13.1 % uniaxial lattice mismatch occurring in this orientation mostly relaxes within the first few monolayers of growth by forming a coincidence site lattice, where 7 GaN planes coincide with 8 ScN planes, leaving the ScN surface nearly free of extended defects. Overgrowth of the ScN with GaN leads to a kinetic stabilization of the zinc blende phase, that rapidly develops wurtzite inclusions nucleating on {111} nanofacets, commonly observed during zinc blende GaN growth. Our ScN/GaN($1\bar{1}00$) platform opens a new route for the epitaxy of twin-free metal-semiconductor heterostructures made of closely lattice-matched GaN, ScN, HfN and ZrN compounds., Comment: Main Paper: 10 pages, 5 figures; Supplementary Information: 2 pages, 1 figure

(In,Ga) alloy droplets are used to catalyse the growth of (In,Ga)As nanowires by molecular beam epitaxy on Si(111) substrates. The composition, morphology and optical properties of these nanowires can be tuned by the employed elemental fluxes. To incorporate more than 10% of In, a high In/(In+Ga) flux ratio above 0.7 is required. We report a maximum In content of almost 30% in bulk (In,Ga)As nanowires for an In/(In+Ga) flux ratio of 0.8. However, with increasing In/(In+Ga) fl ux ratio, the nanowire length and diameter are notably reduced. Using photoluminescence and cathodoluminescence spectroscopy on nanowires covered by a passivating (In,Al)As shell, two luminescence bands are observed. A significant segment of the nanowires shows homogeneous emission, with a wavelength corresponding to the In content in this segment, while the consumption of the catalyst droplet leads to a spectrally-shifted emission band at the top of the nanowires. The (In,Ga)As nanowires studied in this work provide a new approach for the integration of infrared emitters on Si platforms.

Capitalizing on the directed nature of the atomic fluxes in molecular beam epitaxy, we propose and demonstrate the sequential directional deposition of lateral (In,Ga)N shells on GaN nanowires. In this approach, a sub-monolayer thickness of each constituent atomic species, i.e. Ga, In, and N, is deposited subsequently from the same direction by rotating the sample and operating the shutters accordingly. Using multiple iterations of this process, we achieve the growth of homogeneous shells on a single side facet of the nanowires. For higher In content and thus lattice mismatch, we observe a strain-induced bending of the nanowire heterostructures. The incorporation of In and the resulting emission spectra are systematically investigated as a function of both the growth temperature and the In/Ga flux ratio.

Using molecular beam epitaxy, we demonstrate the growth of (In,Ga)N shells emitting in the green spectral range around very thin (35 nm diameter) GaN core nanowires. These GaN nanowires are obtained by self-assembled growth on TiN. We present a qualitative shell growth model accounting for both the three-dimensional nature of the nanostructures as well as the directionality of the atomic fluxes. This model allows us, on the one hand, to optimise the conditions for high and homogeneous In incorporation and, on the other hand, to explain the influence of changes in the growth conditions on the sample morphology and In content. Specifically, the impact of the V/III and In/Ga flux ratios, the rotation speed and the rotation direction are investigated. Notably, with In acting as surfactant, the ternary (In,Ga)N shells are much more homogeneous in thickness along the NW length than their binary GaN counterparts.

An accurate knowledge of the optical constants (refractive index $n$ and extinction coefficient $k$) of ScN is crucial for understanding the optical properties of this binary nitride semiconductor as well as for its use in optoelectronic applications. Using spectroscopic ellipsometry in a spectral range from far infrared to far ultraviolet (0.045-8.5 eV), we determine $n$ and $k$ of ScN layers grown on Al$_{2}$O$_{3}$(0001) substrates by plasma-assisted molecular beam epitaxy. Fits of ellipsometry data return the energies of four oscillators representing critical points in the band structure of ScN, namely, 2.03, 3.89, 5.33, and 6.95 eV. As the infrared range is dominated by free carriers, the vibrational properties of the layers are examined by Raman spectroscopy. Despite the rocksalt structure of ScN, several first-order phonon modes are observed, suggesting a high density of point defects consistent with the high electron density deduced from Hall measurements. Finally, photoluminescence measurements reveal an emission band slightly above the lowest direct bandgap. We attribute the redshift of the peak emission energy from 2.3 to 2.2 eV with increasing layer thickness to a reduction of the O concentration in the layers.

We study the molecular beam epitaxy of AlN nanowires between 950 and 1215 {\deg}C, well above the usual growth temperatures, to identify optimal growth conditions. The nanowires are grown by self-assembly on TiN(111) films sputtered onto Al$_2$O$_3$. Above 1100 {\deg}C, the TiN film is seen to undergo grain growth and its surface exhibits {111} facets where AlN nucleation preferentially occurs. Modelling of the nanowire elongation rate measured at different temperatures shows that the Al adatom diffusion length is maximised at 1150 {\deg}C, which appears to be the optimum growth temperature. However, analysis of the nanowire luminescence shows a steep increase in the deep-level signal already above 1050 {\deg}C, associated with O incorporation from the Al$_2$O$_3$ substrate. Comparison with AlN nanowires grown on Si, MgO and SiC substrates suggests that heavy doping of Si and O by interdiffusion from the TiN/substrate interface increases the nanowire internal quantum efficiency, presumably due to the formation of a SiN$_x$ or AlO$_x$ passivation shell. The outdiffusion of Si and O would also cause the formation of the inversion domains observed in the nanowires. It follows that for optoelectronic and piezoelectric applications, optimal AlN nanowire ensembles should be prepared at 1150 {\deg}C on TiN/SiC substrates and will require an ex situ surface passivation., Comment: Main Paper: 13 pages, 5 figures; Supporting Information: 4 pages, 4 figures

Using low-temperature cathodoluminescence spectroscopy, we study the properties of N- and Al-polar AlN layers grown by molecular beam epitaxy on bulk AlN{0001}. Compared to the bulk AlN substrate, layers of both polarities feature a suppression of deep-level luminescence, a total absence of the prevalent donor with an exciton binding energy of 28 meV, and a much increased intensity of the emission from free excitons. The dominant donor in these layers is characterized by an associated exciton binding energy of 13 meV. The observation of excited exciton states up to the exciton continuum allows us to directly extract the $\Gamma_{5}$ free exciton binding energy of 57 meV.

(La and Ga)-doped tin monoxide (stannous oxide, tin (II) oxide, SnO) thin films were grown by plasma-assisted and suboxide molecular beam epitaxy with dopant concentrations ranging from $\approx5\times10^{18}$cm$^{-3}$ to $2\times10^{21}$cm$^{-3}$. In this concentration range, the incorporation of Ga into SnO was limited by the formation of secondary phases observed at $1.2\times10^{21}$cm$^{-3}$ Ga, while the incorporation of La showed a lower solubility limit. Transport measurements on the doped samples reveal that Ga acts as an acceptor and La as a compensating donor. While Ga doping led to an increase of the hole concentration from $1\times10^{18}$cm$^{-3}-1\times10^{19}$cm$^{-3}$ for unintentionally (UID) SnO up to $5\times10^{19}$cm$^{-3}$, La-concentrations well in excess of the UID acceptor concentration resulted in semi-insulating films without detectable $n$-type conductivity. Ab-initio calculations qualitatively agree with our dopant assignment of Ga and La, and further predict In$_\text{Sn}$ to act as an acceptor as well as Al$_\text{Sn}$ and B$_\text{Sn}$ as donor. These results show the possibilities of controlling the hole concentration in $p$-type SnO, which can be useful for a range of optoelectronic and gas-sensing applications., Comment: 6 pages, 5 figures

GaAs-based nanowires are among the most promising candidates for realizing a monolithical integration of III-V optoelectronics on the Si platform. To realize their full potential for applications as light absorbers and emitters, it is crucial to understand their interaction with light governing the absorption and extraction efficiency, as well as the carrier recombination dynamics determining the radiative efficiency. Here, we study the spontaneous emission of zincblende GaAs/(Al,Ga)As core/shell nanowire arrays by $\mu$-photoluminescence spectroscopy. These ordered arrays are synthesized on patterned Si(111) substrates using molecular beam epitaxy, and exhibit an exceptionally low degree of polytypism for interwire separations exceeding a critical value. We record emission spectra over more than five orders of excitation density for both steady-state and pulsed excitation to identify the nature of the recombination channels. An abrupt Mott transition from excitonic to electron-hole-plasma recombination is observed, and the corresponding Mott density is derived. Combining these experiments with simulations and additional direct measurements of the external quantum efficiency using a perfect diffuse reflector as reference, we are able to extract the internal quantum efficiency as a function of carrier density and temperature as well as the extraction efficiency of the nanowire array. The results vividly document the high potential of GaAs/(Al,Ga)As core/shell nanowires for efficient light emitters integrated on the Si platform. Furthermore, the methodology established in this work can be applied to nanowires of any other materials system of interest for optoelectronic applications.

An accurate knowledge of the lattice parameters of the new nitride Sc$_\textit{x}$Al$_\textit{1-x}$N is essential for understanding the elastic and piezoelectric properties of this compound as well as for the ability to engineer its strain state in heterostructures. Using high-resolution x-ray diffractometry, we determine the lattice parameters of 100-nm-thick undoped Sc$_\textit{x}$Al$_\textit{1-x}$N layers grown on GaN(0001) templates by plasma-assisted molecular beam epitaxy. The Sc content $\textit{x}$ of the layers is measured independently by both x-ray photoelectron spectroscopy and energy-dispersive x-ray spectroscopy and ranges from 0 to 0.25. The in-plane lattice parameter of the layers linearly increases with increasing $\textit{x}$, while their out-of-plane lattice parameter remains constant. Layers with $\textit{x}$ $\approx$ 0.09 are found to be lattice matched to GaN, resulting in a smooth surface and a structural perfection equivalent to that of the GaN underlayer. In addition, a two-dimensional electron gas is induced at the Sc$_\textit{x}$Al$_\textit{1-x}$N/GaN heterointerface, with the highest sheet electron density and mobility observed for lattice-matched conditions.

By employing a mixed SnO$_2$+Sn source, we demonstrate suboxide molecular beam epitaxy growth of phase-pure single crystalline metastable SnO(001) thin films at a growth rate of ~1.0nm/min without the need for additional oxygen. These films grow epitaxially across a wide substrate temperature range from 150 to 450{\deg}C. Hence, we present an alternative pathway to overcome the limitations of high Sn or SnO$_2$ cell temperatures and narrow growth windows encountered in previous MBE growth of metastable SnO. In-situ laser reflectometry and line-of-sight quadrupole mass spectrometry were used to investigate the rate of SnO desorption as a function of substrate temperature. While SnO ad-molecules desorption at Ts = 450{\deg}C was growth-rate limiting,the SnO films did not desorb at this temperature after growth in vacuum. The SnO (001) thin films are transparent and unintentionally p-type doped, with hole concentrations and mobilities in the range of 0.9 to 6.0x10$^{18}$cm$^{-3}$ and 2.0 to 5.5 cm$^2$/V.s, respectively. These p-type SnO films obtained at low temperatures are promising for back-end-of-line (BEOL) compatible applications and for integration with n-type oxides in p-n heterojunction and field-effect transistors, Comment: 18 pages, 10 figures

We explore and systematically compare the morphological, structural and optical properties of GaN/(Al,Ga)N multiple quantum wells (MQWs) grown by plasma-assisted molecular beam epitaxy (PA-MBE) on freestanding GaN$(0001)$ and GaN$(000\bar{1})$ substrates. Samples of different polarity are found to be comparable in terms of their morphological and structural perfection and exhibit essentially identical quantum well widths and Al content. Regardless of the crystal orientation, the exciton decay in the MQWs at 10 K is dominantly radiative and the photoluminescence (PL) energy follows the quantum confined Stark effect (QCSE) for different quantum well widths. A prominent free-to-bound transition involving interface shallow donors is, however, visible for the N-polar MQWs. At room-temperature, in contrast, the exciton decay in all samples is dominated by nonradiative recombination taking place at point defects, presumably Ca or V N located at the bottom QW interface. Remarkably, the N-polar MQWs exhibit a higher PL intensity and longer decay times than the Ga-polar MQWs at room-temperature. This improved internal quantum efficiency is attributed to the beneficial orientation of the internal electric field that effectively reduces the capture rate of minority carriers by interface trap states.

This report classifies emission inhomogeneities that manifest in InGaN quantum well blue light-emitting diodes grown by plasma-assisted molecular beam epitaxy on free-standing GaN substrates. By a combination of spatially resolved electroluminescence and cathodoluminescence measurements, atomic force microscopy, scanning electron microscopy and hot wet KOH etching, the identified inhomogeneities are found to fall in four categories. Labeled here as type I through IV, they are distinguishable by their size, density, energy, intensity, radiative and electronic characteristics and chemical etch pits which correlates them with dislocations. Type I exhibits a blueshift of about 120 meV for the InGaN quantum well emission attributed to a perturbation of the active region, which is related to indium droplets that form on the surface in the metal-rich InGaN growth condition. Specifically, we attribute the blueshift to a decreased growth rate of and indium incorporation in the InGaN quantum wells underneath the droplet which is postulated to be the result of reduced incorporated N species due to increased N$_{2}$ formation. The location of droplets are correlated with mixed type dislocations for type I defects. Types II through IV are due to screw dislocations, edge dislocations, and dislocation bunching, respectively, and form dark spots due to leakage current and nonradiative recombination., Comment: 11 pages, 8 figures

In this work, we show the heteroepitaxial growth of single-crystalline bixbyite (In$_{1-x}$Ga$_x$)$_2$O$_3$ films on (111)-oriented yttria-stabilized zirconia substrates using plasma-assisted molecular beam epitaxy under various growth conditions. A pure In$_2$O$_3$ buffer layer between the substrate and (In$_{1-x}$Ga$_x$)$_2$O$_3$ alloy is shown to result in smoother film surfaces and significantly improved crystallinity. Symmetric out-of-plane 2$\theta - \omega$ x-ray diffraction scans show a single (111) crystal orientation and transmission electron microscopy confirms the single-crystallinity up to $x = 0.18$ and only slight film quality deterioration with increasing Ga content. Partially relaxed layers are demonstrated via reciprocal space mapping with lattice parameters fitting well to Vegard's law. However, the Ga cations are not evenly distributed within the films containing nominally $x > 0.11$: inclusions with high Ga density up to $x = 0.50$ are observed within a "matrix" with $x \approx 0.08$. The cubic bixbyite phase is preserved, in both the "matrix" and the inclusions. Moreover, for $x \geq 0.11$, both the Raman phonon lines as well as the optical absorption onset remain nearly constant. Hard x-ray photoelectron spectroscopy measurements also indicate a widening of the band gap and exhibit similar saturation of the Ga 2p core level position for high Ga contents. This saturation behavior of the spectroscopic properties further supports the limited Ga incorporation into the "matrix" of the film., Comment: 15 pages, 16 figures

The influence of Ga incorporation into cubic In$_2$O$_3$ on the electronic and vibrational properties is discussed for (In$_{1-x}$,Ga$_x$)$_2$O$_3$ alloy films grown by molecular beam epitaxy. Using spectroscopic ellipsometry, a linear dependence of the absorption onset on the Ga content $x$ is found with a blueshift of up to 150 meV for $x = 0.1$. Consistently, the fundamental band gap exhibits a blueshift as determined by hard X-ray photoelectron spectroscopy. The dependence of the absorption onset and the effective electron mass on the electron concentration is derived from the infrared dielectric functions for a Sn doped alloy film. The influence of alloying on phonon modes is analyzed on the basis of Raman spectroscopic measurements. The frequencies of several phonon modes are identified as sensitive measures for the spectroscopic determination of the Ga content.

We investigate the impact of threading dislocations with an edge component (a or a+c-type) on carrier recombination and diffusion in GaN(0001) layers close to the surface as well as in the bulk. To this end, we utilize cathodoluminescence imaging of the top surface of a GaN(0001) layer with a deeply buried (In,Ga)N quantum well. Varying the acceleration voltage of the primary electrons and comparing the signal from the layer and the quantum well enables us to probe carrier recombination at depths ranging from the close vicinity of the surface to the position of the quantum well. Our experiments are accompanied by fully three-dimensional Monte Carlo simulations of carrier drift, diffusion, and recombination in the presence of the surface, the quantum well, and the dislocation, taking into account the dislocation strain field and the resulting piezoelectric field at the dislocation outcrop. Near the surface, this field establishes an exciton dead zone around the dislocation, the extent of which is not related to the carrier diffusion length. However, reliable values of the carrier diffusion length can be extracted from the dipole-like energy shift observed in hyperspectral cathodoluminescence maps recorded around the dislocation outcrop at low acceleration voltages. For high acceleration voltages, allowing us to probe a depth where carrier recombination is unaffected by surface effects, we observe a much stronger contrast than expected from the piezoelectric field alone. This finding provides unambiguous experimental evidence for the strong nonradiative activity of edge threading dislocations in bulk GaN and hence also in buried heterostructures.

We determine the diffusion length of excess carriers in GaN by spatially resolved cathodoluminescence spectroscopy utilizing a single quantum well as carrier collector or carrier sink. Monochromatic intensity profiles across the quantum well are recorded for temperatures between 10 and 300 K. A classical diffusion model accounts for the profiles acquired between 120 and 300 K, while for temperatures lower than 120 K, a quantum capture process has to be taken into account in addition. Combining the diffusion length extracted from these profiles and the effective carrier lifetime measured by time-resolved photoluminescence experiments, we deduce the carrier diffusivity as a function of temperature. The experimental values are found to be close to theoretical ones for the ambipolar diffusivity of free carriers limited only by intrinsic phonon scattering. This agreement is shown to be fortuitous. The high diffusivity at low temperatures instead originates from an increasing participation of excitons in the diffusion process.

Nanoprobe X-ray diffraction (nXRD) using focused synchrotron radiation is a powerful technique to study the structural properties of individual semiconductor nanowires. However, when performing the experiment under ambient conditions, the required high X-ray dose and prolonged exposure times can lead to radiation damage. To unveil the origin of radiation damage, we compare nXRD experiments carried out on individual semiconductor nanowires in their as grown geometry both under ambient conditions and under He atmosphere at the microfocus station of the P08 beamline at the 3rd generation source PETRA III. Using an incident X-ray beam energy of 9 keV and photon flux of 10$^{10}$s$^{-1}$, the axial lattice parameter and tilt of individual GaAs/In$_{0.2}$Ga$_{0.8}$As/GaAs core-shell nanowires were monitored by continuously recording reciprocal space maps of the 111 Bragg reflection at a fixed spatial position over several hours. In addition, the emission properties of the (In,Ga)As quantum well, the atomic composition of the exposed nanowires and the nanowire morphology are studied by cathodoluminescence spectroscopy, energy dispersive X-ray spectroscopy and scanning electron microscopy, respectively, both prior to and after nXRD exposure. Nanowires exposed under ambient conditions show severe optical and morphological damage, which was reduced for nanowires exposed under He atmosphere. The observed damage can be largely attributed to an oxidation process from X-ray induced ozone reactions in air. Due to the lower heat transfer coefficient compared to GaAs, this oxide shell limits the heat transfer through the nanowire side facets, which is considered as the main channel of heat dissipation for nanowires in the as-grown geometry.

The determination of the carrier diffusion length of semiconductors such as GaN and GaAs by cathodoluminescence imaging requires accurate knowledge about the spatial distribution of generated carriers. To obtain the lateral distribution of generated carriers for sample temperatures between 10 and 300 K, we utilize cathodoluminescence intensity profiles measured across single quantum wells embedded in thick GaN and GaAs layers. Thin (Al,Ga)N and (Al,Ga)As barriers, respectively, prevent carriers diffusing in the GaN and GaAs layers to reach the well, which would broaden the profiles. The experimental cathodoluminescence profiles are found to be systematically wider than the energy loss distributions calculated by means of the Monte Carlo program CASINO, with the width monotonically increasing with decreasing temperature. This effect is observed for both GaN and GaAs and becomes more pronounced for higher acceleration voltages. We discuss this phenomenon in terms of both, the electron-phonon interaction controlling the energy relaxation of hot carriers, and the shape of the initial carrier distribution. Finally, we present a phenomenological approach to simulate the carrier generation volume that can be used for the investigation of the temperature dependence of carrier diffusion.

We report on the direct correlation between the structural and optical properties of single, as-grown core-multi-shell GaAs/In$_{0.15}$Ga$_{0.85}$As/GaAs/AlAs/GaAs nanowires. Fabricated by molecular beam epitaxy on a pre-patterned Si(111) substrate, on a row of well separated nucleation sites, it was possible to access individual nanowires in the as-grown geometry. The polytype distribution along the growth axis of the nanowires was revealed by synchrotron-based nanoprobe X-ray diffraction techniques monitoring the axial 111 Bragg reflection. For the same nanowires, the spatially-resolved emission properties were obtained by cathodoluminescence hyperspectral linescans in a scanning electron microscope. Correlating both measurements, we reveal a blueshift of the shell quantum well emission energy combined with an increased emission intensity for segments exhibiting a mixed structure of alternating wurtzite and zincblende stacking compared with the pure crystal polytypes. The presence of this mixed structure was independently confirmed by cross-sectional transmission electron microscopy., Comment: This is an author-created, un-copyedited version of an article published in Nanotechnology. IOP Publishing Ltd. is not responsible for any errors or omissions in this version of the manuscript or any version derived from it. The Version of Record is available online at https://doi.org/10.1088/1361-6528/ab7590

Understanding the interplay between the structure, composition and opto-electronic properties of semiconductor nano-objects requires combining transmission electron microscopy (TEM) based techniques with electrical and optical measurements on the very same specimen. Recent developments in TEM technologies allow not only the identification and in-situ electrical characterization of a particular object, but also the direct visualization of its modification in-situ by techniques such as Joule heating. Over the past years, we have carried out a number of studies in these fields that are reviewed in this contribution. In particular, we discuss here i) correlated studies where the same unique object is characterized electro-optically and by TEM, ii) in-situ Joule heating studies where a solid-state metal-semiconductor reaction is monitored in the TEM, and iii) in-situ biasing studies to better understand the electrical properties of contacted single nanowires. In addition, we provide detailed fabrication steps for the silicon nitride membranes crucial to these correlated and in-situ measurements., Comment: This is an author-created, un-copyedited version of a topical review published in Nanotechnology. IOP Publishing Ltd. is not responsible for any errors or omissions in this version of the manuscript or any version derived from it. The Version of Record is available online at https://doi.org/10.1088/1361-6528/ab99f0

The growth of NiO on GaN(00.1) substrates by plasma-assisted molecular beam epitaxy under oxygen rich conditions was investigated at growth temperatures between 100 $^{\circ}$C and 850 $^{\circ}$C. Epitaxial growth of NiO(111) with two rotational domains, with epitaxial relation $\normalsize{}\mathrm{\mathrm{\mathrm{NiO}(1\bar{\mathrm{{1}}}0)}\:||\:\mathrm{\mathrm{GaN}(11.0)}}$ and $\mathrm{\mathrm{\mathrm{NiO}\mathrm{(10\bar{\mathrm{{1}}})}\:||\:\mathrm{GaN(11.0)}}}$, was observed by X-ray diffraction (XRD) and confirmed by in-situ reflection high-energy electron diffraction as well as transmission electron microscopy (TEM) and electron backscatter diffraction. With respect to the high lattice mismatch of 8.1 % and a measured low residual tensile layer strain, growth by lattice matching epitaxy or domain matching epitaxy is discussed. The morphology measured by atomic force microscopy showed a grainy surface, probably arising from the growth by the columnar rotational domains visible in TEM micrographs. The domain sizes measured by AFM and TEM increase with the growth temperature, indicating an increasing surface diffusion length. Growth at 850 $^{\circ}$C, however, involved local decomposition of the GaN substrate that lead to an interfacial $\mathrm{\beta}$-Ga$\mathrm{_{2}}$O$\mathrm{_{3}}$($\bar{\mathrm{{2}}}$01) layer and a high NiO surface roughness. Raman mesurements of the quasi-forbidden one-phonon peak indicate increasing layer quality (decreasing defect density) with increasing growth temperature. The results above suggest optimum growth temperatures around 700 $^{\circ}$C for high layer and interface quality., Comment: 10 pages (+2 Supplement), 12 figures (+2 Supplement). The following article has been submitted to Journal of Applied Physics (October 2019)

We demonstrate the self-assembled formation of AlN nanowires by molecular beam epitaxy on sputtered TiN films on sapphire. This choice of substrate allows growth at an exceptionally high temperature of 1180 {\deg}C. In contrast to previous reports, the nanowires are well separated and do not suffer from pronounced coalescence. This achievement is explained by sufficient Al adatom diffusion on the substrate and the nanowire sidewalls. The high crystalline quality of the nanowires is evidenced by the observation of near band edge emission in the cathodoluminescence spectrum. The key factor for the low nanowire coalescence is the TiN film, which spectroscopic ellipsometry and Raman spectroscopy indicate to be stoichiometric. Its metallic nature will be beneficial for optoelectronic devices employing these nanowires as the basis for (Al,Ga)N/AlN heterostructures emitting in the deep ultraviolet spectral range.

Core-shell GaAs-based nanowires monolithically integrated on Si constitute a promising class of nanostructures that could enable light emitters for fast inter- and intrachip optical connections. We introduce and fabricate a novel coaxial GaAs/(In,Ga)As dot-in-a-well nanowire heterostructure to reach spontaneous emission in the Si transparent region, which is crucial for applications in Si photonics. Specifically, we achieve room temperature emission at 1.27 $\mu$m in the telecommunication O band. The presence of quantum dots in the heterostructure is evidenced by a structural analysis based on scanning transmission electron microscopy. The spontaneous emission of these nanowire structures is investigated by cathodoluminescence and photoluminescence spectroscopy. Thermal redistribution of charge carriers to larger quantum dots explains the long wavelength emission achieved at room temperature. Finally, in order to demonstrate the feasibility of the presented nanowire heterostructures as electrically driven light emitters monolithically integrated on Si, a light emitting diode is fabricated exhibiting room-temperature electroluminescence at 1.26 $\mu$m., Comment: This document is the unedited Author's version of a Submitted Work that was subsequently accepted for publication in ACS Applied Nano Materials (2019), copyright (C) American Chemical Society after peer review. To access the final edited and published work see this https://doi.org/10.1021/acsanm.9b01866, the supporting information is available (free of charge) under the same link

We present the combined analysis of the electroluminescence (EL) as well as the current-voltage (I-V) behavior of single, freestanding (In,Ga)N/GaN nanowire (NW) light-emitting diodes (LEDs) in an unprocessed, self-assembled ensemble grown by molecular beam epitaxy. The data were acquired in a scanning electron microscope equipped with a micromanipulator and a luminescence detection system. Single NW spectra consist of emission lines originating from different quantum wells, and the width of the spectra increases with decreasing peak emission energy. The corresponding I-V characteristics are described well by the modified Shockley equation. The key advantage of this measurement approach is the possibility to correlate the EL intensity of a single NW LED with the actual current density in this NW. This way, the external quantum efficiency (EQE) can be investigated as a function of the current in a single NW LED. The comparison of the EQE characteristic of single NWs and the ensemble device allows a quite accurate determination of the actual number of emitting NWs in the working ensemble LED and the respective current densities in its individual NWs. This information is decisive for a meaningful and comprehensive characterization of a NW ensemble device, rendering the measurement approach employed here a very powerful analysis tool.

We investigate, both theoretically and experimentally, the drift, diffusion, and recombination of excitons in the strain field of an edge threading dislocation intersecting the GaN{0001} surface. We calculate and measure hyperspectral cathodoluminescence maps around the dislocation outcrop for temperatures between 10 to 200 K. Contrary to common belief, the cathodoluminescence intensity contrast is only weakly affected by exciton diffusion, but is caused primarily by exciton dissociation in the piezoelectric field at the dislocation outcrop. Hence, the extension of the dark spots around dislocations in the luminescence maps cannot be used to determine the exciton diffusion length. However, the cathodoluminescence energy contrast, reflecting the local bandgap variation in the dislocation strain field, does sensitively depend on the exciton diffusion length and hence enables its experimental determination.

We demonstrate the top-down fabrication of ordered arrays of GaN nanowires by selective area sublimation of pre-patterned GaN(0001) layers grown by hydride vapor phase epitaxy on Al$_{2}$O$_{3}$. Arrays with nanowire diameters and spacings ranging from 50 to 90 nm and 0.1 to 0.7 $\mu$m, respectively, are simultaneously produced under identical conditions. The sublimation process, carried out under high vacuum conditions, is analyzed \emph{in situ} by reflection high-energy electron diffraction and line-of-sight quadrupole mass spectromety. During the sublimation process, the GaN(0001) surface vanishes, giving way to the formation of semi-polar $\lbrace1\bar{1}03\rbrace$ facets which decompose congruently following an Arrhenius temperature dependence with an activation energy of ($3.54 \pm 0.07$) eV and an exponential prefactor of $1.58\times10^{31}$ atoms cm$^{-2}$ s$^{-1}$. The analysis of the samples by low-temperature cathodoluminescence spectroscopy reveals that, in contrast to dry etching, the sublimation process does not introduce nonradiative recombination centers at the nanowire sidewalls. This technique is suitable for the top-down fabrication of a variety of ordered nanostructures, and could possibly be extended to other material systems with similar crystallographic properties such as ZnO., Comment: This is the accepted manuscript version of an article that appeared in Nanoscale Advances. The CC BY-NC 3.0 license applies, see http://creativecommons.org/licenses/by-nc/3.0/

Nanowire photodetectors are investigated because of their compatibility with flexible electronics, or for the implementation of on-chip optical interconnects. Such devices are characterized by ultrahigh photocurrent gain, but their photoresponse scales sublinearly with the optical power. Here, we present a study of single-nanowire photodetectors displaying a linear response to ultraviolet illumination. Their structure consists of a GaN nanowire incorporating an AlN/GaN/AlN heterostructure, which generates an internal electric field. The activity of the heterostructure is confirmed by the rectifying behavior of the current-voltage characteristics in the dark, as well as by the asymmetry of the photoresponse in magnitude and linearity. Under reverse bias (negative bias on the GaN cap segment), the detectors behave linearly with the impinging optical power when the nanowire diameter is below a certain threshold ($\approx$ 80 nm), which corresponds to the total depletion of the nanowire stem due to the Fermi level pinning at the sidewalls. In the case of nanowires that are only partially depleted, their nonlinearity is explained by a nonlinear variation of the diameter of their central conducting channel under illumination., Comment: This is the accepted manuscript version of an article that appeared in Nanotechnology. The CC BY-NC-ND 3.0 license applies, see https://creativecommons.org/licences/by-nc-nd/3.0

This paper assesses the effects of Ge-doping on the structural and optical (band-to-band and intersubband (ISB)) properties of GaN/AlGaN multi-quantum wells (QWs) designed to display ISB absorption in the short-wave, mid- and far-infrared ranges (SWIR, MIR, and FIR, respectively). The standard c-plane crystallographic orientation is considered for wells absorbing in the SWIR and MIR spectral regions, whereas the FIR structures are grown along the nonpolar m-axis. In all cases, we compare the characteristics of Ge-doped and Si-doped samples with the same design and various doping levels. The use of Ge appears to improve the mosaicity of the highly lattice-mismatched GaN/AlN heterostructures. However, when reducing the lattice mismatch, the mosaicity is rather determined by the substrate and does not show any dependence on the dopant nature or concentration. From the optical point of view, by increasing the dopant density, we observe a blueshift of the photoluminescence in polar samples due to the screening of the internal electric field by free carriers. In the ISB absorption, on the other hand, there is a systematic improvement of the linewidth when using Ge as a dopant for high doping levels, whatever the spectral region under consideration (i.e. different QW size, barrier composition and crystallographic orientation)., Comment: This is the accepted manuscript version of an article that appeared in Semiconductor Science and Technology. The CC BY-NC-ND 3.0 license applies, see https://creativecommons.org/licences/by-nc-nd/3.0

While the properties of wurtzite GaAs have been extensively studied during the past decade, little is known about the influence of the crystal polytype on ternary (In,Ga)As quantum well structures. We address this question with a unique combination of correlated, spatially-resolved measurement techniques on core-shell nanowires that contain extended segments of both the zincblende and wurtzite polytypes. Cathodoluminescence hyperspectral imaging reveals a blueshift of the quantum well emission energy by $75\pm15$ meV in the wurtzite polytype segment. Nanoprobe x-ray diffraction and atom probe tomography enable $\mathbf{k}\cdot\mathbf{p}$ calculations for the specific sample geometry to reveal two comparable contributions to this shift. First, there is a 30% drop in In mole fraction going from the zincblende to the wurtzite segment. Second, the quantum well is under compressive strain, which has a much stronger impact on the hole ground state in the wurtzite than in the zincblende segment. Our results highlight the role of the crystal structure in tuning the emission of (In,Ga)As quantum wells and pave the way to exploit the possibilities of three-dimensional bandgap engineering in core-shell nanowire heterostructures. At the same time, we have demonstrated an advanced characterization toolkit for the investigation of semiconductor nanostructures., Comment: This document is the unedited Author's version of a Submitted Work that was subsequently accepted for publication in Nano Letters (2019), copyright (C) American Chemical Society after peer review. To access the final edited and published work see https://doi.org/10.1021/acs.nanolett.9b01241, the supporting information is available (free of charge) under the same link

We present a systematic study of top-down processed GaN/AlN heterostructures for intersubband optoelectronic applications. Samples containing quantum well superlattices that display either near- or mid-infrared intersubband absorption were etched into nano- and micropillar arrays in an inductively coupled plasma. We investigate the influence of this process on the structure and strain-state, on the interband emission and on the intersubband absorption. Notably, for pillar spacings significantly smaller ($\leq1/3$) than the intersubband wavelength, the magnitude of the intersubband absorption is not reduced even when 90\% of the material is etched away and a similar linewidth is obtained. The same holds for the interband emission. In contrast, for pillar spacings on the order of the intersubband absorption wavelength, the intersubband absorption is masked by refraction effects and photonic crystal modes. The presented results are a first step towards micro- and nanostructured group-III nitride devices relying on intersubband transitions.

We present a study of GaN single-nanowire ultraviolet photodetectors with an embedded GaN/AlN superlattice. The heterostructure dimensions and doping profile were designed in such a way that the application of positive or negative bias leads to an enhancement of the collection of photogenerated carriers from the GaN/AlN superlattice or from the GaN base, respectively, as confirmed by electron beam-induced current measurements. The devices display enhanced response in the ultraviolet A ($\approx$ 330-360 nm) / B ($\approx$ 280-330 nm) spectral windows under positive/negative bias. The result is explained by correlation of the photocurrent measurements with scanning transmission electron microscopy observations of the same single nanowire, and semi-classical simulations of the strain and band structure in one and three dimensions., Comment: This document is the unedited Author's version of a Submitted Work that was subsequently accepted for publication in Nano Letters (2017), copyright (C) American Chemical Society after peer review. To access the final edited and published work see http://doi.org/10.1021/acs.nanolett.7b01118

Intersubband optoelectronic devices rely on transitions between quantum-confined electron levels in semiconductor heterostructures, which enables infrared (IR) photodetection in the 1-30 $\mu$m wavelength window with picosecond response times. Incorporating nanowires as active media could enable an independent control over the electrical cross-section of the device and the optical absorption cross-section. Furthermore, the three-dimensional carrier confinement in nanowire heterostructures opens new possibilities to tune the carrier relaxation time. However, the generation of structural defects and the surface sensitivity of GaAs nanowires have so far hindered the fabrication of nanowire intersubband devices. Here, we report the first demonstration of intersubband photodetection in a nanowire, using GaN nanowires containing a GaN/AlN superlattice absorbing at 1.55 $\mu$m. The combination of spectral photocurrent measurements with 8-band k$\cdot$p calculations of the electronic structure supports the interpretation of the result as intersubband photodetection in these extremely short-period superlattices. We observe a linear dependence of the photocurrent with the incident illumination power, which confirms the insensitivity of the intersubband process to surface states and highlights how architectures featuring large surface-to-volume ratios are suitable as intersubband photodetectors. Our analysis of the photocurrent characteristics points out routes for an improvement of the device performance. This first nanowire based intersubband photodetector represents a technological breakthrough that paves the way to a powerful device platform with potential for ultrafast, ultrasensitive photodetectors and highly-efficient quantum cascade emitters with improved thermal stability., Comment: This document is the unedited Author's version of a Submitted Work that was subsequently accepted for publication in Nano Letters (2017), copyright (C) American Chemical Society after peer review. To access the final edited and published work see http://dx.doi.org/10.1021/acs.nanolett.7b03414 , the supporting information is available (free of charge) under the same link

Electron irradiation of GaN nanowires in a scanning electron microscope strongly reduces their luminous efficiency as shown by cathodoluminescence imaging and spectroscopy. We demonstrate that this luminescence quenching originates from a combination of charge trapping at already existing surface states and the formation of new surface states induced by the adsorption of C on the nanowire sidewalls. The interplay of these effects leads to a complex temporal evolution of the quenching, which strongly depends on the incident electron dose per area. Time-resolved photoluminescence measurements on electron-irradiated samples reveal that the carbonaceous adlayer affects both the nonradiative and the radiative recombination dynamics., Comment: This is an author-created, un-copyedited version of an article accepted for publication/published in Nanotechnology. IOP Publishing Ltd is not responsible for any errors or omissions in this version of the manuscript or any version derived from it. The Version of Record is available online at http://dx.doi.org/10.1088/0957-4484/27/45/455706

We have characterized the photodetection capabilities of single GaN nanowires incorporating 20 periods of AlN/GaN:Ge axial heterostructures enveloped in an AlN shell. Transmission electron microscopy confirms the absence of an additional GaN shell around the heterostructures. In the absence of a surface conduction channel, the incorporation of the heterostructure leads to a decrease of the dark current and an increase of the photosensitivity. A significant dispersion in the magnitude of dark currents for different single nanowires is attributed to the coalescence of nanowires with displaced nanodisks, reducing the effective length of the heterostructure. A larger number of active nanodisks and AlN barriers in the current path results in lower dark current and higher photosensitivity, and improves the sensitivity of the nanowire to variations in the illumination intensity (improved linearity). Additionally, we observe a persistence of the photocurrent, which is attributed to a change of the resistance of the overall structure, particularly the GaN stem and cap sections. In consequence, the time response is rather independent of the dark current., Comment: This document is the unedited Author's version of a Submitted Work that was subsequently accepted for publication in Nano Letters (2016), copyright (C) American Chemical Society after peer review. To access the final edited and published work see http://dx.doi.org/10.1021/acs.nanolett.6b00806

We study the luminescence of unintentionally doped and Si-doped In$_x$Ga$_{1-x}$N nanowires with a low In content (x<0.2) grown by molecular beam epitaxy on Si substrates. The emission band observed at 300 K from the unintentionally doped samples is centered at much lower energies (800 meV) than expected from the In content measured by x-ray diffractometry and energy dispersive x-ray spectroscopy. This discrepancy arises from the pinning of the Fermi level at the sidewalls of the nanowires, which gives rise to strong radial built-in electric fields. The combination of the built-in electric fields with the compositional fluctuations inherent to (In,Ga)N alloys induces a competition between spatially direct and indirect recombination channels. At elevated temperatures, electrons at the core of the nanowire recombine with holes close to the surface, and the emission from unintentionally doped nanowires exhibits a Stark shift of several hundreds of meV. The competition between spatially direct and indirect transitions is analyzed as a function of temperature for samples with various Si concentrations. We propose that the radial Stark effect is responsible for the broadband absorption of (In,Ga)N nanowires across the entire visible range, which makes these nanostructures a promising platform for solar energy applications., Comment: This document is the unedited Author's version of a Submitted Work that was subsequently accepted for publication in Nano Letters (2016), copyright (C) American Chemical Society after peer review. To access the final edited and published work see http://dx.doi.org/10.1021/acs.nanolett.5b03748

We investigate the luminescence of Ga- and N-polar In$_{x}$Ga$_{1-x}$N/In$_{y}$Ga$_{1-y}$N quantum wells (QWs) grown by plasma-assisted molecular beam epitaxy on freestanding GaN as well as 6H-SiC substrates. In striking contrast to their Ga-polar counterparts, the N-polar QWs prepared on freestanding GaN do not exhibit any detectable photoluminescence. Theoretical simulations of the band profiles combined with resonant excitation of the QWs allow us to rule out carrier escape and subsequent surface recombination as the reason for the absence of luminescence. To explore the hypothesis of a high concentration of nonradiative defects at the interfaces between wells and barriers, we analyze Ga- and N-polar QWs prepared on 6H-SiC as a function of the well width. Intense luminescence is observed for both Ga- and N polar samples. As expected, the luminescence of the Ga-polar QWs quenches and red-shifts with increasing well width due to the quantum confined Stark effect. In contrast, both the intensity and the energy of the luminescence from the N-polar samples are essentially independent of well width. Transmission electron microscopy reveals that the N-polar QWs exhibit abrupt interfaces and homogeneous composition, excluding emission from In-rich clusters as the reason for this anomalous behavior. The microscopic origin of the luminescence in the N-polar QWs is elucidated using spatially resolved cathodoluminescence spectroscopy. Regardless of well width, the luminescence is found to not originate from the N-polar QWs, but from the semipolar facets of v-pit defects. These results cast serious doubts on the potential of N-polar QWs grown by plasma-assisted molecular beam epitaxy for the development of long-wavelength light emitting diodes. What remains to be seen is whether unconventional growth conditions may enable a significant reduction in the concentration of nonradiative defects., Comment: 12 pages, 10 figures

We investigate the effect of the p-type top contact on the optoelectronic characteristics of light emitting diodes (LEDs) based on (In,Ga)N/GaN nanowire (NW) ensembles grown by molecular beam epitaxy on Si substrates. We compare devices fabricated with either Ni/Au or indium tin oxide (ITO) top contact. The NW-LEDs with ITO exhibit a number density of NWs emitting electroluminescence about ten times higher, significantly lower turn-on voltage and series resistance, and a relative external quantum efficiency more than one order of magnitude higher than the sample with Ni/Au. These results show that limitations in the performance of such devices reported so far can be overcome by improving the p-type top-contact., Comment: 4 pages, 4 figures

(In,Ga)N insertions embedded in self-assembled GaN nanowires are of current interest for applications in solid state light emitters. Such structures exhibit a notoriously broad emission band. We use cathodoluminescence spectral imaging in a scanning electron microscope and micro-photoluminescence spectroscopy on single nanowires to learn more about the mechanisms underlying this emission. We observe a shift of the emission energy along the stack of six insertions within single nanowires that may be explained by compositional pulling. Our results also corroborate reports that the localization of carriers at potential fluctuations within the insertions plays a crucial role for the luminescence of these nanowire based emitters. Furthermore, we resolve contributions from both structural and point defects in our measurements., Comment: 10 pages, 7 figures

Basal-plane stacking faults are an important class of optically active structural defects in wurtzite semiconductors. The local deviation from the 2H stacking of the wurtzite matrix to a 3C zinc-blende stacking induces a bound state in the gap of the host crystal, resulting in the localization of excitons. Due to the two-dimensional nature of these planar defects, stacking faults act as quantum wells, giving rise to radiative transitions of excitons with characteristic energies. Luminescence spectroscopy is thus capable of detecting even a single stacking fault in an otherwise perfect wurtzite crystal. This review draws a comprehensive picture of the luminescence properties related to stacking faults in GaN. The emission energies associated with different types of stacking faults as well as factors that can shift these energies are discussed. In this context, the importance of the quantum-confined Stark effect in these zinc-blende/wurtzite heterostructures, which results from the spontaneous polarization of wurtzite GaN, is underlined. This discussion is extended to zinc-blende segments in a wurtzite matrix. Furthermore, other factors affecting the emission energy and linewidth of stacking fault-related peaks as well as results obtained at room temperature are addressed. The considerations presented in this article should be transferable also to other wurtzite semiconductors., Comment: 16 pages, 14 figures

The strain state and composition of a 400 nm thick (In,Ga)N layer grown by metal-organic chemical vapor deposition on a GaN template are investigated by spatially integrated x-ray diffraction and cathodoluminescence (CL) spectroscopy as well as by spatially resolved CL and energy dispersive x-ray analysis. The CL investigations confirm a process of strain relaxation accompanied by an increasing indium content toward the surface of the (In,Ga)N layer, which is known as the compositional pulling effect. Moreover, we identify the strained bottom, unstrained top, and gradually relaxed intermediate region of the (In,Ga)N layer. In addition to an increase of the indium content along the growth direction, the strain relaxation leads to an enhancement of the lateral variations of the indium distribution toward the surface., Comment: 4 pages, 5 figures

GaN nanowire ensembles with axial InGaN multi-quantum wells (MQWs) were grown by molecular beam epitaxy. In a series of samples, we varied the In content in the MQWs from almost zero to about 20%. Within the nanowire ensemble, the MQWs fluctuate strongly in composition and size. Statistical information about the composition was obtained from x-ray diffraction and Raman spectroscopy. Photoluminescence at room temperature was obtained in the range from 2.2 eV to 2.5 eV depending on In content. Contrary to planar MQWs, the intensity increases with increasing In content. We compare the observed emission energies with transition energies obtained from a one-dimensional model, and conclude that several mechanisms for carrier localization affect the luminescence of these three-dimensional structures., Comment: This is an author-created, un-copyedited version of an article accepted for publication in Nanotechnology. IOP Publishing Ltd is not responsible for any errors or omissions in this version of the manuscript or any version derived from it. The Version of Record is available online at doi:10.1088/0957-4484/23/45/455203

Light emitting diodes (LEDs) were fabricated using ensembles of free-standing (In,Ga)N/GaN nanowires (NWs) grown on Si substrates in the self-induced growth mode by molecular beam epitaxy. Electron beam induced current analysis, cathodoluminescence as well as biased $\mu$-photoluminescence spectroscopy, transmission electron microscopy, and electrical measurements indicate that the electroluminescence of such LEDs is governed by the differences in the individual current densities of the single-NW LEDs operated in parallel, i.e. by the inhomogeneity of the current path in the ensemble LED. In addition, the optoelectronic characterization leads to the conclusion that these NWs exhibit N-polarity and that the (In,Ga)N quantum well states in the NWs are subject to a non-vanishing quantum confined Stark effect., Comment: This is an author-created, un-copyedited version of an article accepted for publication in Nanotechnology. IOP Publishing Ltd is not responsible for any errors or omissions in this version of the manuscript or any version derived from it. The Version of Record is available online at doi:10.1088/0957-4484/23/46/465301

GaAs nanowires (NWs) grown by molecular-beam epitaxy may contain segments of both the zincblende (ZB) and wurtzite (WZ) phases. Depending on the growth conditions, we find that optical emission of such NWs occurs either predominantly above or below the band gap energy of ZB GaAs [E(g,ZB)]. This result is consistent with the assumption that the band gap energy of wurtzite GaAs [E(g,WZ)] is larger than E(g,ZB) and that GaAs NWs with alternating ZB and WZ segments along the wire axis establish a type II band alignment, where electrons captured within the ZB segments recombine with holes of the neighboring WZ segments. Thus, the corresponding transition energy depends on the degree of confinement of the electrons, and transition energies exceeding E(g,ZB) are possible for very thin ZB segments. At low temperatures, the incorporation of carbon acceptors plays a major role in determining the spectral profile as these can effectively bind holes in the ZB segments. From cathodoluminescence measurements of single GaAs NWs performed at room temperature, we deduce a lower bound of 55 meV for the difference E(g,WZ)-E(g,ZB)., Comment: 8 pages, 10 figures