Search

In this work, ZnO/SnS/indium tin oxide (ITO)/glass functional heterostructures have been developed using a combined approach of electrodeposition of a SnSx layer and successive ionic layer adsorption and reaction (SILAR) of the ZnO layer. The high-quality 400 nm-thick orthorhombic SnS0.9–0.95 films were formed on the ITO substrates with a thickness of 130 nm and an electrical conductivity of less than 40 Ω/□. Chemical deposition of ZnO thin films by the SILAR method allowed to deposit hexagonal films with a thickness of about 200 nm. The morphology, elemental and phase composition of the films were characterized by Scanning electron microscopy, energy-dispersive X-ray spectroscopy, X-ray photoelectron spectroscopy, and X-ray diffraction. The band gap (1.4 eV for SnSx and 3.3 eV for ZnO), as well as the high light absorption coefficient of SnSx films (1–2) × 104 cm–1 were determined. The obtained ZnO/SnSx/ITO heterostructures formed by the electrodeposition–SILAR cycle showed a photoEMF value of 198 mV. These properties make ZnO/SnS heterostructure promising for low-cost solar cells based on affordable materials. [ABSTRACT FROM AUTHOR]

The Ni-TiO2 and Ni-CeO2 composite coatings with varying hydrophilic/hydrophobic characteristics were fabricated by the electrodeposition method from a tartrate electrolyte at ambient temperature. To meet the requirements of tight regulation by the European Chemicals Agency classifying H3BO3 as a substance of very high concern, Rochelle salt was utilized as a buffer solution instead. The novelty of this study was to implement a simple one-step galvanostatic electrodeposition from the low-temperature electrolyte based on a greener buffer compared to traditionally used, aiming to obtain new types of soft-matrix Ni, Ni-CeO2, and Ni-TiO2 coatings onto steel or copper substrates. The surface characteristics of electrodeposited nickel composites were evaluated by SEM, EDS, surface contact angle measurements, and XPS. Physiochemical properties of pure Ni, Ni-CeO2, and Ni-TiO2 composites, namely, wear resistance, microhardness, microroughness, and photocatalytic activity, were studied. Potentiodynamic polarization, EIS, and ICP-MS analyses were employed to study the long-term corrosion behavior of coatings in a 0.5 M NaCl solution. Superior photocatalytic degradation of methylene blue, 96.2% after 6 h of illumination, was achieved in the case of Ni-TiO2 composite, while no substantial change in the photocatalytic behavior of the Ni-CeO2 compared to pure Ni was observed. Both composites demonstrated higher hardness and wear resistance than pure Ni. This study investigates the feasibility of utilizing TiO2 as a photocatalytic hydrophilicity promoter in the fabrication of composite coatings for various applications. [ABSTRACT FROM AUTHOR]

In this work, Cu–Sn–TiO2 composite coatings were electrochemically obtained from a sulfate bath containing 0–10 g/L of TiO2 nanoparticles. The effect of TiO2 particles on kinetics of cathodic electrodeposition has been studied by linear sweep voltammetry and chronopotentiometry. As compared to the Cu–Sn alloy, the Cu–Sn–TiO2 composite coatings show rougher surfaces with TiO2 agglomerates embedded in the metal matrix. The highest average amount of included TiO2 is 1.7 wt.%, in the case of the bath containing 5 g/L thereof. Composite coatings showed significantly improved antibacterial properties towards E. coli ATCC 8739 bacteria as compared to the Cu–Sn coatings of the same composition. Such improvement has been connected with the corrosion resistance of the composites studied by linear polarization and electrochemical impedance spectroscopy. In the bacterial media and 3% NaCl solutions, Cu–Sn–TiO2 composite coatings have lower corrosion resistance as compared to Cu–Sn alloys, which is caused by the nonuniformity of the surface. [ABSTRACT FROM AUTHOR]

An inorganic wide-bandgap hole transport layer (HTL), copper(I) thiocyanate (CuSCN), is employed in inorganic planar hydrothermally deposited Sb 2 S 3 solar cells. With excellent hole transport properties and uniform compact morphology, the solution-processed CuSCN layer suppresses the leakage current and improves charge selectivity in an n-i-p-type solar cell structure. The device without the HTL (FTO/CdS/Sb 2 S 3 /Au) delivers a modest power conversion efficiency (PCE) of 1.54%, which increases to 2.46% with the introduction of CuSCN (FTO/CdS/Sb 2 S 3 /CuSCN/Au). This PCE is a significant improvement compared with the previous reports of planar Sb 2 S 3 solar cells employing CuSCN. CuSCN is therefore a promising alternative to expensive and inherently unstable organic HTLs. In addition, CuSCN makes an excellent optically transparent (with average transmittance >90% in the visible region) and shunt-blocking HTL layer in pinhole-prone ultrathin (<100 nm) semitransparent absorber layers grown by green and facile hydrothermal deposition. A semitransparent device is fabricated using an ultrathin Au layer (∼10 nm) with a PCE of 2.13% and an average visible transmittance of 13.7%., Competing Interests: The authors declare no competing financial interest., (© 2024 The Authors. Published by American Chemical Society.)