Search

A 100-MeV Compact Electron Accelerator design has been proposed for Very High Energy Electron (VHEE) radiotherapy research at Tsinghua University. The microwave source for this system is a 50 MW X-band klystron, paired with a pulse compressor featuring a correction cavity chain. During high-power test, the system achieved a flat-top power gain three times the input. The acceleration system consists of three main components: a backward traveling-wave buncher that bunches and accelerates electrons from a thermionic cathode gun to 8 MeV, followed by two 72-cell X-band constant-gradient traveling-wave accelerating structures, which further increase the electron energy to 100 MeV with a gradient of 80 MV/m. The total length of the system is 1.8 m, and its design is detailed in this paper. [ABSTRACT FROM AUTHOR]

To achieve coherent power combination of Ka-band high-power microwave (HPM), a phase-locked klystron-type coaxial relativistic Cherenkov generator (PKC-RCG), which combines the advantageous characteristics of weak dimensional sensitivity of RCG and low input power ratio of relativistic triaxial klystron amplifier (TKA), is proposed and investigated in this paper. The PKC-RCG is composed of two parts: a pre-modulation region adapted from TKA and an energy exchange region adapted from RCG. The pre-modulation region is used for initial speed modulation of intense relativistic electron beams (IREB), ensuring that the output frequency is consistent with the input frequency. The energy exchange region is used for deep clustering of the IREB and achieving efficient beam–wave energy conversion. Phase locking of the output HPM is accomplished through phase delivery of the modulated IREB. Specially designed reflectors and cascaded single-gap bunching cavities with active suppression of asymmetric TM mode are employed in the pre-modulation region to suppress energy coupling and achieve a lower input power ratio. Disk-loaded slow-wave structure with smooth inner conductor is employed in the energy exchange region to further decrease the dimensional sensitivity of RCG. By the proposed Ka-band PKC-RCG, an HPM with a power of 550 MW and a frequency of 29.0 GHz is obtained with ohmic loss being taken into account. Moreover, the input power ratio and phase-locking bandwidth of the proposed Ka-band PKC-RCG are −51.4 dB and 30 MHz, respectively. [ABSTRACT FROM AUTHOR]

A prototype amplifier with operating frequency f = 2.8 GHz for a pulsed RF power supply of high-power amplifying klystrons is developed. The amplifier's block diagram is developed. Board topologies are proposed for each amplifier module. Model amplifier modules are assembled and adjusted. The model amplifier is assembled and tested. [ABSTRACT FROM AUTHOR]

To investigate the velocity distribution and atomization characteristics of gas–liquid swirl coaxial (GLSC) injectors, atomization experiments and simulations were conducted under atmospheric conditions. The velocity distribution and morphology of the spray from GLSC injectors at varying gas–liquid ratios were measured using particle image velocimetry. The gas–liquid interaction, breakup dynamics, and the velocity of liquid sheet were simulated based on the three-dimensional volume of fluid to discrete particle model (VOF-to-DPM) and octree adaptive mesh refinement. Additionally, a method for extracting droplet diameters from high-quality images has been developed and validated. The results indicate that the sprays maintain a stable cone when the gas–liquid ratio is low. As the gas–liquid ratio increases, particularly at larger recess ratios, self-pulsation phenomena occur. During self-pulsation, the spray cone angle is enlarged, and the breakup length shortens. In a stable spray field, the center exhibits a low velocity region (5–10 m/s), while the spray periphery shows a high velocity region (20–25 m/s). Self-pulsation is induced by the "Klystron effect," which arises from the Kelvin–Helmholtz (K–H) instability at the gas–liquid interface. The center of the self-pulsated spray transitions to a high velocity region due to the accelerated droplet motion driven by the annular gas flow through the spray's center. The radial distribution of mean droplet diameters for both stable and self-pulsated sprays has been summarized. As the gas–liquid ratios and recess ratios increase, the global droplet diameters gradually decrease, with a 75% of droplet diameters falling between 0 and 0.1 mm. [ABSTRACT FROM AUTHOR]

An equivalent circuit analysis has been proposed for co-axial reentrant cavities which have been used extensively in Multiple-beam Klystron (MBK). Formulation for the equivalent capacitance and inductance of coaxial reentrant cavities (single and double reentrant cavity) have been obtained and used for the calculation of cavity parameters, i.e. resonant frequency and characteristic shunt impedance. The unloaded quality factor of the cavities has been obtained using Wheeler's incremental inductance rule. Simulations of coaxial reentrant cavities have been carried out using CST studio and simulation results have been compared with the results obtained from the proposed analysis. A good agreement between the results has been obtained. [ABSTRACT FROM AUTHOR]

An X-band high-power microwave (HPM) oscillator packaged with permanent magnets is proposed. The oscillator employs a radially non-uniform modulation cavity structure to enhance the modulation depth of the electron beam, thereby improving the conversion efficiency of the device. Verified by particle-in-cell simulation, the device achieves an HPM output at X-band with a frequency of 9.38 GHz and power of 3.1 GW, corresponding to a power efficiency of 44.5%, under the conditions of a permanent magnet field of 0.4 T, a diode voltage of 600 kV, and a beam current of 11.6 kA. [ABSTRACT FROM AUTHOR]

This paper introduces a high-power broadband X-band klystron amplifier that achieves an output power of 157 MW and a 3 dB operating bandwidth of 6.7%. The amplifier employs an explosive emission diode with high impedance, which balances the requirements of high power and broadband. The multi-gap input and output cavities are designed to operate at two different longitudinal modes within the operating frequency band, resulting in a flat absorption rate and output efficiency. Moreover, an eight-stage stagger-tuned bunching section is implemented to achieve a uniform fundamental harmonic current modulation depth across the frequency band. Simulation results indicate that when the diode voltage is 550 kV and the beam current is 550 A, the amplifier can achieve a maximum power of 157 MW with an efficiency of 51.9% at the central frequency of 9.8 GHz. Furthermore, within the 3 dB operating bandwidth of 6.7% (670 MHz), the power output remains higher than 80 MW. This novel klystron amplifier structure exhibits exceptional performance in terms of bandwidth, power, and efficiency, thus validating the effectiveness of the design in enhancing bandwidth and providing a solid foundation for the broadband design of high-power microwave sources. [ABSTRACT FROM AUTHOR]

To achieve compactness and miniaturization for high-power microwave devices, this paper proposes an X-band permanent magnet-packaged coaxial relativistic klystron oscillator (RKO) with a novel diode structure featuring a stair-step cathode. First, by adopting a large-radius anode structure, the emission of beam currents from the side of the cathode surface is diminished, thereby reducing the proportion of the backward current in the beam current from 10% to 7%. Second, a stair-step cathode is used to inhibit the return flow of electron beams from striking the anode and generating plasma. Concurrently, a radially non-uniform coaxial resonant cavity structure is employed to enhance the fundamental wave modulation depth of the electron beam and improve the beam–wave interaction's efficiency. The experimental results show that the novel device outputs a microwave with a frequency of 9.46 GHz and a pulse width of 55 ns. It generates a power output of 1.5 GW with an efficiency of approximately 30.5%, in the case in which the diode voltage is 505 kV, the beam current is 9.7 kA, and the guiding magnetic flux density is 0.4 T. This novel structure surpasses traditional diode configurations by enhancing the beam-to-wave conversion efficiency by roughly 10%, thereby offering substantial support for the compactness and miniaturization of RKO. [ABSTRACT FROM AUTHOR]

The response characteristics of the bi-swirl coaxial injector under oscillating backpressure were investigated numerically based on coupled level-set and volume of fluid model. The backpressure oscillation frequency was set ranging from 1000 to 5000 Hz. The frequency and amplitude response characteristics of liquid films were analyzed under different injection conditions. The amplitude of the pressure response inside the injector was determined by the acoustic damping of the system. Due to the central gas core inside the inner injector, the inner injector manifold was found to be more sensitive to the backpressure oscillation. The frequency characteristic of the liquid film response indicated the presence of the characteristic frequency where the response amplitude was maximum. This characteristic frequency was linearly positively correlated with the mass flow rate of the inner injector, while the flow in the outer injector could suppress the response amplitude of liquid films. Meanwhile, the nonlinearity of the response was dominated by the inner liquid film and was also the strongest at the frequency with the highest response amplitude. The simulated flow fields showed that the oscillation of the ambient airflow periodically hindered the liquid film, leading to Klystron effect. Finally, it was suggested that the characteristic frequency was related to the axial velocity of the inner liquid film at the injector outlet and the acoustic length of the gas core. In addition, the response amplitude of liquid films was found to be controlled by the spray cone angle and the total mass flow rate of propellants. [ABSTRACT FROM AUTHOR]

This article presents a demonstration of the improved performance of an X‐ray free‐electron laser (FEL) using the optical klystron mechanism and helical undulator configuration, in comparison with the common planar undulator configuration without optical klystron. The demonstration was carried out at Athos, the soft X‐ray beamline of SwissFEL. Athos has variable‐polarization undulators, and small magnetic chicanes placed between every two undulators to fully exploit the optical klystron. It was found that, for wavelengths of 1.24 nm and 3.10 nm, the required length to achieve FEL saturation is reduced by about 35% when using both the optical klystron and helical undulators, with each effect accounting for about half of the improvement. Moreover, it is shown that a helical undulator configuration provides a 20% to 50% higher pulse energy than planar undulators. This work represents an important step towards more compact and high‐power FELs, rendering this key technology more efficient, affordable and accessible to the scientific community. [ABSTRACT FROM AUTHOR]

The design and development of the electron gun for vacuum electronic devices is a critical and challenging task having a profound impact on device performance. Current state-of-the-art electron gun simulation codes employ the concept of a virtual cathode for the simulation of space charge-limited electron guns, where the virtual cathode distance is to be provided as an input by the user. In this report, an approach to calculate the virtual cathode position through analytical formulation and simulation is presented. The effect of inaccurate virtual cathode on gun parameters is studied through simulation and its repercussions are explained. The approach has been applied in the simulation using three-dimensional tracking solver to design a 50 kV, 10 Amp electron gun, which is to be used in a C-band Klystron. Based on the design, a Gun-Collector-Test-Module (GCTM) has been developed and hot-tested for experimental validation. A good agreement between the simulated and measurement results validates the design approach of the electron gun. [ABSTRACT FROM AUTHOR]

Copyright of Atomic Energy Science & Technology is the property of Editorial Board of Atomic Energy Science & Technology and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Beam stability and timing jitter in modern linear accelerators are becoming increasingly important. In particular, if a magnetic or radio-frequency (RF) compression regime is employed, the beam time of arrival jitter at the end of the linac can be strictly correlated with the phase noise of the accelerating fields of the RF structure working off-crest. For this reason, since 2008, an RF fast-feedback technique, which acts within each RF pulse, has been successfully employed at LNF-INFN (Laboratori Nazionali di Frascati dell'Istituto Nazionale di Fisica Nucleare) in the SPARC_LAB (Sources for Plasma Accelerators and Radiation Compton with Laser And Beam) facility on S-band (2856 MHz) klystrons powered by pulse-forming network (PFN) modulators, as reported in this paper. However, in order to meet the more stringent requirements of plasma wakefield acceleration schemes, some upgrades to this feedback system have been recently carried out. The first prototype has been experimentally tested on a C-band (5712 MHz) klystron, driven by a solid-state modulator, in order to investigate the possibility for additional improvement resulting from the inherently more stable power source. In this paper, the design, realization and the preliminary measurement results obtained at SPARC_LAB after such upgrades will be reviewed. [ABSTRACT FROM AUTHOR]

This paper presents an extended interaction klystron (EIK) operating at 0.22 THz based on a four-sheet-beam orthogonal interconnection structure (OIS). The proposed OIS comprises four vertically positioned trapezoidal line structures, significantly enhancing the coupling efficiency between cavities and achieving optimal interactions with the TM81 mode. This study investigates the dispersion characteristics and field distribution numerically, while the optimal working parameters and output structure were analyzed using the particle-in-cell (PIC) studio. The parameters of each cavity and the selection of five intermediate cavities were finalized by calculating the beam conductance, external quality factor, and stagger-tuning. The EIK generated a continuous 480 W output power with a four-sheet-beam at 17.5 kV and a current density of 200 A/cm2 from an input drive signal of 20 mW. The gain was approximately 43.8 dB. [ABSTRACT FROM AUTHOR]

The manufacturing of active RF devices like klystrons is dominated by expensive and time-consuming cycles of machining and brazing. In this article, we characterize the RF properties of X-band klystron cavities and an integrated circuit manufactured with a novel additive manufacturing process. Parts are 3D printed in 316 L stainless steel with direct metal laser sintering, electroplated in copper, and brazed in one simple braze cycle. Stand-alone test cavities and integrated circuit cavities were measured throughout the manufacturing process. The un-tuned cavity frequency varies by less than 5% of the intended frequency, and Q factors reach above 1200. A tuning study was performed, and unoptimized tuning pins achieved a tuning range of 138 MHz without compromising Q. Klystron system performance was simulated with as-built cavity parameters and realistic tuning. Together, these results show promise that this process can be used to cheaply and quickly manufacture a new generation of highly integrated high power vacuum devices. [ABSTRACT FROM AUTHOR]

The electromagnetic characteristics of the input cavity with electron beams loaded are measured successfully in an X-band triaxial relativistic klystron amplifier (TKA) with a high frequency electrical probe. To solve the frequency response issue in the X band, a coaxial electrical probe is optimized and inserted obliquely into the input cavity at the designed angle so that the microwaves in the cavity can be sampled and extracted with the required coupling coefficient while the probe does not interfere with the solenoid coil, which is tightly integrated outside the TKA. Besides, the TKA is redesigned as a structure integrally sealed by the solenoid coil, and the secondary sealing induced by probe insertion is implemented on the flange of the solenoid coils rather than on the wall of the TKA, which is conducive to simplifying the coupling structure while maintaining the high vacuum level. The design is examined in a GW level TKA experiment, indicating that microwaves with a power of about 670 MW are generated in the input cavity at a frequency of 8.40 GHz, which is completely consistent with the injected and output microwave frequencies. [ABSTRACT FROM AUTHOR]

The results of numerical simulation of a multiple-beam X-band klystron have been presented. The analysis of a new principle of constructing the interaction space that allows us to provide a high efficiency value without using second harmonic resonators has been given. The results of an experimental study of the developed 25-beam KIU-283 klystron with a peak power of 3.0 MW at a frequency of 9300 MHz with an electronic efficiency of 58% have been presented. [ABSTRACT FROM AUTHOR]

For most applications in the millimeter wave band, corresponding to Ka and higher-frequency bands, relatively high atmospheric absorption necessitates the use of high-power sources. Here, a new approach for projecting an oversized beam tunnel in an overmoded structure by concentrating the axial field is demonstrated to meet the high-frequency and high-power demands of compact devices. Due to the enhanced intense beam loading capability of the interaction circuit, a six-cavity Ka-band extended interaction klystron with a four-coupling-hole disk-loaded structure is designed that can stably obtain high output power. An analysis of optimization tradeoffs from introducing high order modes for allowing the application of more powerful beams to improving high order mode field distribution for enhancing the electron-wave coupling and suppressing mode competition is reported. 3D particle-in-cell simulations show attainable output powers of 1.11 MW at 32.94 GHz with a saturated gain of 57 dB by injecting a 3.3 mm diameter electron beam with a current of 24 A. [ABSTRACT FROM AUTHOR]

Future linear accelerators require klystrons with higher radio frequency (RF) to drive higher gradient accelerating structure. An x-band accelerator structure was used to accelerate electrons at the Shanghai Soft X-ray Free Electron Laser Facility (SXFEL) in Shanghai Advanced Research Institute, Chinese Academy of Sciences (SARI-CAS). A pulse transformer is a crucial device in an RF system. This study presents a highvoltage pulse transformer used for a 50 MW x-band pulsed klystron in SXFEL. Typical specifications of the pulse transformer are peak pulse voltage 420 kV, peak pulse current 300 A, 50 Hz repetition rate and 1.5 µs flattop pulse width. Design and optimization of pulse transformer are achieved by using equivalent circuit analytic methods and computational aided simulation. The relevant experiments show that this pulse transformer can meet the requirements of 50MW x-band klystron. [ABSTRACT FROM AUTHOR]

The V-band frequencies are becoming popular due to their application potential towards secure high data rate communications. This article reports bandwidth enhancement of an 11-cavity V-band Klystron amplifier employing staggered tuning. A systematic approach is presented to stagger-tune the periodically allocated multiple cavities of the Klystron operating at 60.1 GHz. Using the three-dimensional particle-in-cell (PIC) simulation, it is shown that, employing the proposed approach, the −3 dB bandwidth of the device (with peak tuned configuration) has been increased from 165 MHz to 540 MHz, demonstrating a 260% increment. The −1 dB bandwidth of the device is estimated to be 270 MHz. The proposed approach of stagger tuning may be employed for similar devices employing multiple RF cavities to meet the requirement of wide bandwidth. [ABSTRACT FROM AUTHOR]

Increasing klystron tubes' efficiency is essential in developing new-generation colliders and free-electron lasers. Different factors can affect the efficiency of a multi-beam klystron. One of the significant factors is the electric field symmetry inside cavities, especially in the output section. In this research, two different types of couplers are investigated in the extraction cavity of a 40-beam klystron. The first approach is a single slot coupler, which is frequently utilized and easier to fabricate but disturbs the electric field symmetry inside the extraction cavity. The second method has a more complex structure with symmetric electric fields. In this design, the coupler consists of 28 mini slots on the inner wall of the coaxial extraction cavity. Both designs are evaluated via particle in cell simulations, and the results exhibit around 30% more power extracted from the structure with a symmetric field distribution. The symmetric structures can also decrease the number of back-streamed particles by up to 70%. [ABSTRACT FROM AUTHOR]

Copyright of Atomic Energy Science & Technology is the property of Editorial Board of Atomic Energy Science & Technology and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Based on steady-state experiments, a three-dimensional (3D) simulation study under pulsation conditions was carried out. This was performed to study the effect of pulsation of the supply system on the atomization characteristics of a gas-centered swirl coaxial injector. The results indicated that the spray shape resembled a pagoda when the Klystron effect occurred. When the low-frequency pulsation (200 Hz) was applied to the liquid inlet, the peak of the exit pressure was close to the trough of the inlet mass flow rate. Meanwhile, the exit mass flow rate and pressure were approximately sinusoidal. There was no significant lag effect in the response of the exit mass flow rate to the inlet mass flow rate but with a small sawtooth-like oscillation. Increasing the amplitude of the liquid inlet disturbance amplified the exit mass flow rate fluctuation, which was greater than the set amplitude of the inlet pulsation. The dominant frequency of the injector exit mass flow rate and pressure variation was significantly less than the inlet pulsation frequency when the frequency of the liquid inlet pulsation was increased to 1000 Hz. This was due to the low-pass filtering effect of the annular slit. There was no significant change in the overall spray morphology for the gas inlet pulsation. By applying the same amplitude and frequency of pulsation to the gas and liquid inlets of the injector, the pulsation of the liquid inlet had a stronger effect on the injector exit spray than that of the gas inlet. [ABSTRACT FROM AUTHOR]

This paper presents the design, prototype engineering, and initial testing of a relatively low-voltage, high aspect ratio electron gun for versatile pulsed power applications. The sheet beam, diode electron gun is designed for (23–25) kV voltage and 6 µA/V1.5, as is required for x-band klystron, as a part of a compact Klylac delivering electron beam energy in the MeV range. The gun prototype was engineered, built, and tested using a Scandinova M1-0.5 modulator. Beam loss on the anode aperture is evaluated from transient waveforms and equivalent circuit modeling. [ABSTRACT FROM AUTHOR]

In this paper, an angular radial extended interaction amplifier (AREIA) that consists of a pair of angular extended interaction cavities is proposed. Both the convergence angle cavity and the divergence angle cavity, which are designed for the converging beam and diverging beam, respectively, are investigated to present the potential of the proposed AREIA. They are proposed and explored to improve the beam–wave interaction capability of W-band extended interaction klystrons (EIKs). Compared to conventional radial cavities, the angular cavities have greatly decreased the ohmic loss area and increased the characteristic impedance. Compared to the sheet beam (0°) cavity, it has been found that the convergence angle cavity has a higher effective impedance and the diverging beam has a weaker space-charge effect under the same ideal electron beam area; the advantages become more obvious as the propagation distance increases. Particle-in-cell (PIC) results have shown that the diverging beam (8°) EIA performs better at an output power of 94 GHz under the condition of lossless, while the converging beam (−2°) EIA has a higher output power of 6.24 kW under the conditions of ohmic loss, an input power of 0.5 W, and an ideal electron beam of 20.5 kV and 1.5 A. When the loss increases and the beam current decreases, the output power of the −2° EIA can be improved by nearly 30% compared to the 0° EIA, and the −2° EIA has a greatly improved beam–wave interaction capacity than conventional EIAs under those conditions. In addition, an angular radial electron gun is designed. [ABSTRACT FROM AUTHOR]

The feasibility of a photonic band-gap (PBG)-based interaction structure was analytically explored for a multiple-beam extended interaction klystron amplifier. This configuration accrues the advantages of the multiple-defect PBG-based extended interaction structure and multiple-beam operation. The mode configurations were analysed through 3D electromagnetic simulation and the applicability of the photonic band-gap cavity was studied for the multiple-beam operation of an extended interaction klystron amplifier. A typical six-defect cavity operating at around 83 GHz was designed for electron–wave interaction at 2π mode with 6 electron beams each carrying 300 mA current at the accelerating potential of 16.5 kV. A particle-in-cell simulation shows that an output power of ∼2 kW is possible with electronic efficiency of around 6.7%. A frequency-scaled-down interaction structure at Ku-band was fabricated and cold measurements were carried out to ascertain the feasibility. The measured values of the frequency for various modes, loaded quality factor and 3 dB bandwidth were found to be within 0.36%, 5.3% and 4.07%, respectively, against those from the simulation. [ABSTRACT FROM AUTHOR]

A high-efficiency interaction circuit for Ka-band klystron has been proposed based on a novel internal coupling cavity. Driven by a 25 kV, 5A pencil beam, the interaction circuit can produce a peak output power of 38.4kW at Ka-band, and the electronic efficiency is 30.7%. The electromagnetic properties of the unequal slot multi-gap cavity and internal coupling cavity have been studied and compared. The internal coupling cavity demonstrated a higher coupling coefficient and characteristic impedance than the unequal slot multi-gap cavity, which can improve the circuit efficiency. Stability and pattern analysis have been performed on the output cavity. A four-gap output cavity has been designed. Simulation results show that there is no mode competition and oscillation in the output cavity. The corresponding beam optics has also been designed to produce the required beam. Compared with the existing work, the interaction circuit can produce almost twice the output power with the same beam voltage and Brillouin focusing magnetic field. The efficiency is also improved by 6 percent. [ABSTRACT FROM AUTHOR]

Copyright of Telecommunication Engineering is the property of Telecommunication Engineering and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

To realize online measurement of power, frequency, and phase for a modularized relativistic triaxial klystron amplifier in a narrow space, a compact directional coupler with high directivity, high power handling capacity, and large bandwidth has been investigated numerically and experimentally. The method with coupling holes distributed in both the longitudinal and lateral directions is proposed, and the simulation results indicate that when two holes are employed, directivity larger than 20 dB is achieved over a 300 MHz bandwidth in the X-band and the maximal electric field strength is controlled to be 198.5 kV/cm with 1 GW power injection, while the whole coupler longitude is optimized to be as short as 50 mm. High power experiments have been performed with a 10 GHz relativistic triaxial klystron amplifier, and the results show that the measured power, frequency, and phase shift of the directional coupler have good agreement with the results obtained in the far-field. [ABSTRACT FROM AUTHOR]

We report the high gradient testing results of two single-cell off-axis coupled standing wave accelerating structures. Two brazed standing wave off-axis coupled structures with the same geometry were tested: one made of pure copper (Cu) and one made of a copper–silver (CuAg) alloy with a silver concentration of 0.08%. A peak surface electric field of 450 MV/m was achieved in the CuAg structure for a klystron input power of 14.5 MW and a 1 μs pulse length, which was 25% higher than the peak surface electric field achieved in the Cu structure. The superb high gradient performance was achieved because of the two major optimizations in the cavity's geometry: (1) the shunt impedance of the cavity was maximized for a peak surface electric field to accelerating gradient ratio of ∼2 for a fully relativistic particle, and (2) the peak magnetic field enhancement due to the input coupler was minimized to limit pulse heating. These tests allow us to conclude that C-band accelerating structures can operate at peak fields similar to those at higher frequencies while providing a larger beam iris for improved beam transport. [ABSTRACT FROM AUTHOR]

A compact Ku-band triaxial klystron amplifier (TKA) with three cascaded single-gap bunching cavities is proposed for the sake of high output efficiency at low seed injection power. The three bunching cavities are specially designed with optimal external quality factors and specific drift tube length to suppress the self-oscillation of these cavities. By decreasing the coupling coefficients and increasing the frequency interval of the three cavities, the asymmetric mode competition can be successfully eliminated in 3D particle-in-cell simulation. The compact TKA is demonstrated to be capable of producing the Ku-band high power radiation with a peak power of 580 MW corresponding to an efficiency of 31 % and a pulse duration of nearly 100 ns in typical experiments. Furthermore, the seed injection power and axial length of the proposed device are reduced to 9 kW and 10 wavelengths, respectively. [ABSTRACT FROM AUTHOR]

Ka-band frequencies are becoming increasingly popular due to their application potential in high-data-rate wireless communications relevant to 5G applications, satellite link establishment, etc. High-power amplifiers in this frequency band, offering several tens of watts of output RF power, are one of the main enabling components of these communication systems. This article reports the design studies and analysis of the radio frequency (RF) section of a multiple beam-extended interaction klystron (MB-EIK). The proposed multiple beam RF section with a ladder-type EIK structure offers several crucial features, such as a low-voltage operation, moderate operational bandwidth, and high output power. Starting from the design of the intermediate cavities, the input and output sections and the overall RF section are presented. The proposed RF section supports the operation at 28.5 GHz center frequency with about a 500 MHz 3 dB bandwidth employing four electron beams with a 4 kV DC accelerating field. [ABSTRACT FROM AUTHOR]

Developing a robust and reliable high-voltage (HV) pulse power system (PPS) is essential for the characterization and testing of microwave tubes and industrial applications. This paper presents the design, simulation, and implementation of a modular and versatile high-voltage pulse power supply used in microwave device characterization and testing. A microcontroller-based digitally controlled pulse generation unit is also developed to generate the trigger pulses for high-voltage switching modules to control the turn-ON and turn-OFF of the switching devices. The digitally controlled pulse generation unit provides better resolution of pulse width, pulse repetition frequency, and system protection over the entire range of operations. The pulse generation and control circuit controls the pulse repetition frequency (PRF) and pulse wide (PW). The PRF and PW can be varied from 100 to 1000 Hz and 10 to 100 µs, respectively. The experimental prototype with ten series-connected high-voltage modules is connected to achieve a 25 kV pulsed output voltage. The experimental results of HV-PPS on a resistive dummy load and 5 GHz klystron tube are presented in this work. [ABSTRACT FROM AUTHOR]

To solve the problem of mode competition in high-order working modes, this paper presents a fast design method based on the TM31-2π mode for the dumbbell shaped extended interaction cavity. Based on the equivalent circuit theory, the high-frequency characteristics of the structure are studied. In addition, we propose a W-band continuous wave sheet beam extended interaction klystron high-frequency circuit. The circuit was driven by a 20 kV and 0.85 A sheet electron beam, with a 3.2 × 0.3 mm2 section. The beam was focused by a 0.8 T permanent magnet system. The high-frequency system adopts five dumbbell shaped five-gap cavities, and the output system adopts a symmetrical output waveguide. The 3D particle-in-cell simulation shows that more than 1.5 kW power can be obtained at an input power of 0.12 W, and the electron efficiency and gain are 9.2% and 41.2 dB, respectively. [ABSTRACT FROM AUTHOR]

The excitation and suppression of asymmetric modes in a coaxial relativistic klystron amplifier (RKA) with cascaded single-gap bunching cavities are analyzed in this paper. Through theoretical analysis and simulated verification, we find that the asymmetric modes of cascaded single-gap bunching cavities have low external quality factors, the same resonant frequencies, and negative beam-loading conductance ratios so that they are easily excited by the electron beam. To solve this issue, a feasible method is proposed in this paper to suppress the asymmetric modes of cascaded single-gap bunching cavities, under the conditions of decreasing their coupling coefficients and increasing the frequency separation, choosing an appropriate drift tube length between them. These improved bunching cavities are further examined in an X-band coaxial RKA by 3D particle-in-cell simulation, which shows that high power microwaves with a power of 0.8 GW are generated corresponding to an efficiency of 40%. Furthermore, there is no asymmetric mode competition during 150 ns of simulation time. [ABSTRACT FROM AUTHOR]

This article presents the design, analysis, and simulation for the klystron coaxial radio frequency (RF) output windows. Three new RF windows (Type-2, 3, and 4) are proposed based on the coaxial RF window with a doorknob structure (Type-1) to improve its performances. The proposed RF windows are simulated in high frequency simulator structure. At the operating frequency, the return loss are obtained as −49, −60, −56, and −52 dB, and the insert loss as −0.003 62, −0.002 51, −0.002 74, and −0.003 dB, respectively, for Type1, 2, 3, and 4. Moreover, for Type-1, the E-field near the short-circuit surface is significantly greater than that near the output port side due to the asymmetrical structure of RF window. However, this phenomenon has been greatly improved in the proposed RF windows. The heat load because of RF power absorption over the ceramic has been calculated. The distribution of heat load in three new windows is more uniform and less than that in Type-1, and the heat load in Type-2 is about half of that in Type-1. The thermal and structural analyses of RF windows predict the lower temperature and less mechanical deformation for the three new RF windows. Multipactor analysis is carried out to determine the safety at the operating power level. [ABSTRACT FROM AUTHOR]

In this paper, we investigate a large-sized beam tunnel, G-band extended interaction klystron (EIK) with a traveling wave output structure for the development of broad bandwidth EIKs. The high-quality factor F was introduced to estimate the bandwidth characteristics of the cluster cavities, and the optimal cluster cavity structure parameters were obtained based on this factor. The simulation mode of the device was designed by the 3D particle-in-cell (PIC) commercial simulation software. Four cluster cavities with a staggered distribution of frequencies were employed to expand the bunching bandwidth, and two traveling wave modes, 2π−π/10 and 2π−2π/10, were used as the operating modes in the output structure, effectively increasing the output bandwidth. The simulation findings show that the maximum output power is 170 W, the corresponding gain is 37.5 dB, and the 3-dB bandwidth is up to 1.25 GHz. The three-hole coupling structure with a large-sized beam tunnel provides convenience for the fabrication of devices in the G-band, and our study shows a potential method for the realization of a G-band broadband EIK. [ABSTRACT FROM AUTHOR]

The paper presents the results of three-dimensional modeling of a two-gap output cavity of three-barreled multibeam klystrons. The coaxial output of energy has a simple design and allows achieving the simultaneous output of microwave energy at two frequ encies of the Ku band, one of which is in the beginning of the range and corresponds to the antiphase (π) type of oscillations of double gridless gap, and the second of which corresponds to the inphase (2π) type in the end of this range. It is shown that the application of the developed cavity in a three-barreled design of 57-beam klystrons with a general number of beams N = 57 allows, at working on a inphase type of oscillations, obtaining the level of continuous output power of approximately 3 kW in the amplification band of 100 MHz at an accelerating voltage of 5.4 kV and current density in a single beam of 35 A/cm2. It is shown that the self-excitation of a klystron cavity on the antiphase type of oscillations is absent. This is reached due to the presence of metamaterial in the hybrid design of the output cavity and as a result of optimal selection of the parameters of double gaps that avoids the appearance of interaction regions with the negative zone of electron-type conductivity. It is demonstrated that the frequency of the inphase type of oscillations can be adjusted (within 12%) using the longitudinal ribs introduced into the volume of the cavity. [ABSTRACT FROM AUTHOR]

The results of study carried out at JSC NPP Almaz over the past ten years on the application and prospects for the use of carbon materials in heat-loaded units of TWTs and klystrons are presented. [ABSTRACT FROM AUTHOR]

The paper considers the use of a metamaterial consisting of an array of metal inductive inserts in the gap of the cavity of a multibeam klystron to significantly increase the area of the interaction region. Using analytical estimates and numerical simulation, it is shown that inserts can provide an increase in the phase velocity of the wave in the gap and, consequently, an increase in the uniformity of the field acting on the beams. This makes it possible to increase the number of beams, and, accordingly, the power of the klystron, without increasing the accelerating voltage. Cavities for S- and Ka-band klystrons have been studied. [ABSTRACT FROM AUTHOR]

This letter reports the successful development of an S-band short-length, high-efficiency, coaxial cavity multi-beam relativistic klystron amplifier (CCMB-RKA). The simulation in one-dimensional genetic algorithm, capable of giving high-efficiency parameters, predicted 67% efficiency of CCMB-RKA, taking the interaction length as 600 mm, beam voltage as 420 kV, and beam current as 230 A. However, for accurate results, the CCMB-RKA was simulated again using three-dimensional code CHIPIC, taking RF input power, beam voltage, and beam current as 4.4 kW, 420 kV, and 3.22 kA ($= {14} \times {230}$ A, 14 being the beam number), respectively, predicting the output power, gain, and efficiency of the device as 810 MW, 53 dB, and 60%, respectively. Finally, the designed CCMB-RKA was built and experimented with. Through 20 groups of the comparative experiments, the GW-level RF output power of the device, typically, 1.027 GW (peak), 60 ns pulse was demonstrated with 55% efficiency, 370 phase jitter, and 53 dB gain, taking the RF input power, beam voltage, and beam current as 4.8 kW, 453 kV, and 4.1 kA, respectively. The results establish the potential of the CCMB-RKA developed for high-power microwave applications. [ABSTRACT FROM AUTHOR]

A Dielectric Disk Accelerator (DDA) is a metallic accelerating structure loaded with dielectric disks to increase coupling between cells, thus producing a high group velocity, while still maintaining a high shunt impedance. This is crucial for achieving high efficiency, high gradient acceleration in the short rf pulse acceleration regime. Recent research of these structures has produced traveling wave structures that are powered by very short (∼ 9 ns), very high power (400 MW) RF pulses using two beam acceleration at the Argonne Wakefield Accelerator Complex. In testing, these structures have withstood more than 320 MW of power and produced accelerating gradients of over 100 MV/m. A new standing wave DDA structure is being fabricated for testing on the Nextef2 test stand at KEK that will be powered by a more conventional, klystron power source. Simulation results of this structure show that at 50 MW of input power, the DDA produces a 457 MV/m gradient. It also has a large shunt impedance of 160 M Ω /m and an r/Q of 21.6 k Ω /m. Cold testing of this structure was conducted this summer showing a good match with the excited field but a significantly lower matching at the working frequency. [ABSTRACT FROM AUTHOR]

Klystrons are the predominant RF power sources utilized in large particle accelerators, and enhancing klystron efficiency is crucial for reducing the overall energy consumption of these accelerators. One optional approach to improve klystron efficiency is implementing the depressed collector technique, successfully applied in low-power microwave electronic vacuum devices such as TWT and TV communication klystrons. While the theoretical advancements in klystron efficiency are promising, the practical integration of these techniques, particularly in high-power klystrons, remains challenging. In this paper, a depressed collector design applied to high-power klystrons will be proposed, laying the foundation for improving the overall efficiency of the RF power source in the Circular Electron Positron Collider(CEPC). To verify the key technology of energy recovery for the klystron, we designed an energy recovery verification device composed of an electron gun and a collector. The one-stage depressed collector was theoretically analyzed, and the electrode parameters were determined through simulation design. Beam optics was simulated using DGUN and CST software, while thermal analysis of the collector was performed with ANSYS software. The structural design of the collector was optimized to meet electrical insulation and breakdown requirements. Additionally, secondary electron emission was considered, and its effect on reflux electrons was mitigated, achieving a collector efficiency simulation result of 88.2 %. • The depressed collector finds application in high-power CW klystrons. • Deionized water cooling allows the depressed collector to maintain efficient heat dissipation and performance at high operating voltages. • A ceramic cylinder enhances the insulation capability of the electrodes in the depressed collector. • The structure of the depressed collector is more compact, occupying a smaller volume. [ABSTRACT FROM AUTHOR]

CW magnetrons, initially developed for industrial RF heaters, were suggested to power RF cavities of superconducting accelerators due to their higher efficiency and lower cost than traditionally used klystrons, IOTs or solid-state amplifiers. RF amplifiers driven by a master oscillator serve as coherent RF sources. CW magnetrons are regenerative RF generators with a huge regenerative gain. This causes regenerative instability with a quite large noise when a magnetron operates with the anode voltage above the threshold of self-excitation. Traditionally, an injection locking by a small signal is used for stabilization of magnetrons. In this case CW magnetrons with the injection-locked oscillations generate a high level of noise. This may preclude use of standard CW magnetrons in this operating mode in the Superconducting RF (SRF) accelerators. In this article we described a method developed for forced RF generation of CW magnetrons when the magnetron startup is provided by the injected forcing signal and the regenerative noise is suppressed. The method is most suitable for powering high Q-factor cavities. [ABSTRACT FROM AUTHOR]

A compact coaxial relativistic klystron amplifier (RKA) with three cascaded bunching cavities is investigated to obtain high efficiency output in this paper. When the injection power and drift tube length are both decreased for the compactness of the initial coaxial RKA, the conversion efficiency of this device decreases to only 20%, which is mainly due to the insufficient modulation of intense relativistic electron beam (IREB). To solve this issue, three cascaded bunching cavities are designed to strengthen the modulation of IREB, and each bunching cavity is designed to a non-uniform single-gap cavity with a high external quality factor. Moreover, a specific drift tube length is chosen for minimizing the TEM mode leakage between every two adjacent cavities. With these methods, the self-oscillation between input and three cascaded bunching cavities can be successfully suppressed without loading any reflectors. The proposed three cascaded single-gap bunching cavities are further examined in a Ku-band coaxial RKA, and the output efficiency of this device increases to 44%, which is more than twice that of the initial coaxial RKA. Furthermore, the injection power and axial length of the propagating IREB in the improved coaxial RKA are reduced to only 5 kW and 10 wavelengths, respectively. [ABSTRACT FROM AUTHOR]

Self-oscillation of three cascaded reflectors easily occurs in a triaxial klystron amplifier (TKA) since the TEM mode leakage cannot be cut off by a coaxial waveguide. To solve this issue, we propose a non-uniform reflector to obtain an optimal external quality factor, which indicates its minimum TEM mode leakage. The self-oscillation of three non-uniform reflectors is then suppressed by selecting a specific drift tube length between them. Moreover, different eigenfrequencies are chosen for the three improved reflectors to enhance the tolerance of the drift tube length between them. With these methods, the self-oscillation of three cascaded reflectors can be successfully eliminated, and a TKA with high output efficiency is capable of achieving a long pulse output. [ABSTRACT FROM AUTHOR]