Search

The Piezo-electric Shear Gauge (PSG) [Christensen & Olsen, Rev. Sci. Instrum. 66, 5019, 1995] is a rheometric technique developed to measure the complex shear modulus of viscous liquids near their glass transition temperature. We report recent advances to the PSG technique: 1) The data extraction procedure is optimized which extends the upper limit of the frequency range of the method to between 50 and 70 kHz. 2) The measuring cell is simplified to use only one piezo-electric ceramic disc instead of three. We present an implementation of this design intended for liquid samples. Data obtained with this design revealed that a soft extra spacer is necessary to allow for thermal contraction of the sample in the axial direction. Model calculations show that flow in the radial direction is hindered by the confined geometry of the cell when the liquid becomes viscous upon cooling. The method is especially well-suited for -- but not limited to -- glassy materials., Comment: 21 pages, 15 figures. Final revision before publication

In this article we report on the design, manufacture and testing of a high-pressure cell for doing simultaneous dielectric and neutron spectroscopy. This cell is a unique tool for studying dynamics on different timescales, from kilo- to picoseconds, covering universal features such as the alpha relaxation and fast vibrations at the same time. The cell, constructed in cylindrical geometry, is made in high-strength aluminum alloy and operates up to 500 MPa in a temperature range between roughly 2 and 320 K. In order to measure the scattered neutron intensity and the sample capacitance simultaneously, a cylindrical capacitor is positioned within the bore of the high-pressure container. The capacitor consists of two concentric electrodes separated by insulating spacers. The performance of this setup has been successfully verified by collecting simultaneous dielectric and neutron spectroscopy data on dipropylene glycol, using both backscattering and time-of-flight instruments. We have carried out the experiments at different combinations of temperature and pressure in both supercooled liquid and glassy state., Comment: A.S. and H.W.H. contributed equally to this work

We present a simple method for fast and cheap thermal analysis on supercooled glass-forming liquids. This "Thermalization Calorimetry" technique is based on monitoring the temperature and its rate of change during heating or cooling of a sample for which the thermal power input comes from heat conduction through an insulating material, i.e., is proportional to the temperature difference between sample and surroundings. The monitored signal reflects the sample's specific heat and is sensitive to exo- and endothermic processes. The technique is useful for studying supercooled liquids and their crystallization, e.g., for locating the glass transition and melting point(s), as well as for investigating the stability against crystallization and estimating the relative change in specific heat between the solid and liquid phases at the glass transition., Comment: 17 pages, 9 figures, minor changes

The frequency dependent specific heat has been measured under pressure for the molecular glass forming liquid 5-polyphenyl-4-ether in the viscous regime close to the glass transition. The temperature and pressure dependence of the characteristic timescale associated with the specific heat is compared to the equivalent timescale from dielectric spectroscopy performed under identical conditions. It is shown that the ratio between the two timescales is independent of both temperature and pressure. This observation is non-trivial and demonstrates the existence of specially simple molecular liquids in which different physical relaxation processes are both as function of temperature and pressure/density governed by the same underlying "inner clock". Furthermore, the results are discussed in terms of the recent conjecture that van der Waals liquids, like the measured liquid, comply to the isomorph theory., Comment: 6 pages, 3 figures

A recent study [Gainaru et al. PRL., 112, 098301 (2014)] of two supercooled monohydroxy alcohols close to the glass-transition temperature showed that the Debye peak, thus far mainly observed in the electrical response, also has a mechanical signature. In this work, we apply broadband shear-mechanical spectroscopy to a systematic series of octanol structural isomers, x-methyl-3-heptanol (with x ranging from 2 to 6). We find that the characteristics of the mechanical signature overall follow the systematic behavior observed in dielectric spectroscopy. However, the influence from the molecular structure is strikingly small in mechanics (compared to roughly a factor 100 increase in dielectric strength) and one isomer clearly does not conform to the general ordering. Finally, the mechanical data surprisingly indicate that the size of the supramolecular structures responsible for the Debye process is nearly unchanged in the series., Comment: 5 pages, 4 figures

The frequency-dependent dielectric constant, shear and adiabatic bulk moduli, longitudinal thermal expansion coefficient, and longitudinal specific heat have been measured for two van der Waals glass-forming liquids, tetramethyl-tetraphenyl-trisiloxane (DC704) and 5-polyphenyl-4-ether. Within the experimental uncertainties the loss-peak frequencies of the measured response functions have identical temperature dependence over a range of temperatures, for which the Maxwell relaxation time varies more than nine orders of magnitude. The time scales are ordered from fastest to slowest as follows: Shear modulus, adiabatic bulk modulus, dielectric constant, longitudinal thermal expansion coefficient, longitudinal specific heat. The ordering is discussed in light of the recent conjecture that van der Waals liquids are strongly correlating, i.e., approximate single-parameter liquids., Comment: 8 pages, 6 figures, Substantially revised version

The phenomenology of the beta relaxation process in the shear-mechanical response of glass-forming liquids is summarized and compared to that of the dielectric beta process. Furthermore, we discuss how to model the observations by means of standard viscoelastic modeling elements. Necessary physical requirements to such a model are outlined, and it is argued that physically relevant models must be additive in the shear compliance of the alpha and beta parts. A model based on these considerations is proposed and fitted to data for Polyisobutylene 680., Comment: 8 pages, 6 figures, Minor corrections

We present a direct comparison of the number of dynamically correlated molecules in the shear-mechanical and dielectric relaxations of the following seven supercooled organic liquids: triphenylethylene, tetramethyl-tetraphenyl-trisiloxane, polyphenyl ether, perhydrosqualene, polybutadiene, decahydroisoquinoline, and tripropylene glycol. For each liquid we observe that the numbers of dynamically correlated molecules in the shear and in the dielectric relaxation are proportional. We show that this proportionality can be explained by the constancy of the decoupling index of the shear and dielectric relaxation times in conjunction with time-temperature superposition. Moreover the value of this proportionality constant is related to the difference in stretching of the shear and dielectric response functions. The most significant deviations from unity of this constant are found in a liquid with strong hydrogen bonds and in a polymer., Comment: 8 pages, 8 figures, 1 table

It was recently shown by computer simulations that a large class of liquids exhibits strong correlations in their thermal fluctuations of virial and potential energy [Pedersen et al., Phys. Rev. Lett. 100, 015701 (2008)]. Among organic liquids the class of strongly correlating liquids includes van der Waals liquids, but excludes ionic and hydrogen-bonding liquids. The present note focuses on the density scaling of strongly correlating liquids, i.e., the fact their relaxation time tau at different densities rho and temperatures T collapses to a master curve according to the expression tau propto F(rho^gamma/T) [Schroder et al., arXiv:0803.2199]. We here show how to calculate the exponent gamma from bulk modulus and specific heat data, either measured as functions of frequency in the metastable liquid or extrapolated from the glass and liquid phases to a common temperature (close to the glass transition temperature). Thus an exponent defined from the response to highly nonlinear parameter changes may be determined from linear response measurements.

This paper presents dielectric relaxation data for organic glass-forming liquids compiled from different groups and supplemented by new measurements. The main quantity of interest is the "minimum slope" of the $\alpha$ dielectric loss plotted as a function of frequency in a log-log plot (i.e., the numerically largest slope above the loss peak frequency). The data consisting of 347 spectra for 53 liquids show prevalence of minimum slopes close to -1/2, corresponding to approximate square-root-time dependence of the dielectric relaxation function at short times. The paper further studies possible correlations between minimum slopes and: 1) Temperature quantified via the loss-peak frequency; 2) How well an inverse power law fits data above the loss peak; 3) Degree of time-temperature superposition; 4) Loss-peak half width; 5) Deviation from non-Arrhenius behavior; 6) Loss strength. For the first three points we find correlations that indicate a special status of liquids with minimum slopes close to -1/2. For the last three points only fairly insignificant correlations are found with the exception of large-loss liquids, which have minimum slopes that are numerically significantly larger than 1/2 and loss peak widths that are significantly smaller than those of most other liquids. We conclude that -- excluding large-loss liquids -- approximate $\sqrt t$ relaxation appears to be a generic property of the $\alpha$ relaxation of organic glass formers.

We present a novel method of measuring the frequency dependent specific heat at the glass transition applied to 5-polyphenyl-4-ether. The method employs thermal waves effusing radially out from the surface of a spherical thermistor that acts as both a heat generator and thermometer. It is a merit of the method compared to planar effusion methods that the influence of the mechanical boundary conditions are analytically known. This implies that it is the longitudinal rather than the isobaric specific heat that is measured. As another merit the thermal conductivity and specific heat can be found independently. The method has highest sensitivity at a frequency where the thermal diffusion length is comparable to the radius of the heat generator. This limits in practise the frequency range to 2-3 decades. An account of the 3omega-technique used including higher order terms in the temperature dependency of the thermistor and in the power generated is furthermore given., Comment: 17 pages, 15 figures, Substantially revised version

We report dynamical shear-modulus measurements for five glass-forming liquids (pentaphenyl trimethyl trisiloxane, diethyl phthalate, dibutyl phthalate, 1,2-propanediol, and m-touluidine). The shear-mechanical spectra are obtained by the piezoelectric shear-modulus gauge (PSG) method. This technique allows one to measure the shear modulus ($10^{5} -10^{10}$ Pa) of the liquid within a frequency range from 1 mHz to 10 kHz. We analyze the frequency-dependent response functions to investigate whether time-temperature superposition (TTS) is obeyed. We also study the shear-modulus loss-peak position and its high-frequency part. It has been suggested that when TTS applies, the high-frequency side of the imaginary part of the dielectric response decreases like a power law of the frequency with an exponent -1/2. This conjecture is analyzed on the basis of the shear mechanical data. We find that TTS is obeyed for pentaphenyl trimethyl trisiloxane and in 1,2-propanediol while in the remaining liquids evidence of a mechanical $\beta$ process is found. Although the the high-frequency power law behavior $\omega^{-\alpha}$ of the shear-loss may approach a limiting value of $\alpha=0.5$ when lowering the temperature, we find that the exponent lies systematically above this value (around 0.4). For the two liquids without beta relaxation (pentaphenyl trimethyl trisiloxane and 1,2-propanediol) we also test the shoving model prediction, according to which the the relaxation-time activation energy is proportional to the instantaneous shear modulus. We find that the data are well described by this model., Comment: 7 pages, 6 figures

Shear-mechanical and dielectric measurements on the two monohydroxy (mono-alcohol) molecular glass formers 2-ethyl-1-hexanol and 2-butanol close to the glass transition temperature are presented. The shear-mechanical data are obtained using the piezoelectric shear-modulus gauge method covering frequencies from 1mHz to 10kHz. The shear-mechanical relaxation spectra show two processes, which follow the typical scenario of a structural (alpha) relaxation and an additional (Johari-Goldstein) beta relaxation. The dielectric relaxation spectra are dominated by a Debye-type peak with an additional non-Debye peak visible. This Debye-type relaxation is a common feature peculiar to mono-alcohols. The time scale of the non-Debye dielectric relaxation process is shown to correspond to the mechanical structural (alpha) relaxation. Glass-transition temperatures and fragilities are reported based on the mechanical alpha relaxation and the dielectric Debye-type process, showing that the two glass-transition temperatures differ by approximately 10K and that the fragility based on the Debye-type process is a factor of two smaller than the structural fragility. If a mechanical signature of the Debye-type relaxation exists in these liquids, its relaxation strength is at most 1% and 3% of the full relaxation strength of 2-butanol and 2-ethyl-1-hexanol respectively. These findings support the notion that it is the non-Debye dielectric relaxation process that corresponds to the structural alpha relaxation in the liquid., Comment: 8 pages, 6 figures. Minor corrections, updated figures, more dielectric data shown

We present data for the dielectric relaxation of 43 glass-forming organic liquids, showing that the primary (alpha) relaxation is often close to square-root-time relaxation. The better an inverse power-law description of the high-frequency loss applies, the more accurately is square-root-time relaxation obeyed. These findings suggest that square-root-time relaxation is generic to the alpha process, once a common view, but since long believed to be incorrect. Only liquids with very large dielectric losses deviate from this picture by having consistently narrower loss peaks. As a further challenge to the prevailing opinion, we find that liquids with accurate square-root-time relaxation cover a wide range of fragilities.

We first summarize the classical arguments that the vast majority of glass-forming liquids require more than one "order" parameter for their description. Critiques against this conventional wisdom are then presented, and it is argued that the matter deserves to be reconsidered in light of recent experimental developments. Out of the eight basic thermoviscoelastic frequency-dependent response functions, there are generally three independent functions. For stochastic dynamics we show that there are only two independent response functions; for this case it is shown how analytic continuation may be utilized to express the third response functions in terms of two others. Operational criteria are presented for the linear thermoviscoelasticity being described by a single "order" parameter, in which case there is just one independent thermoviscoelastic response function. It is shown that a single "order" parameter description applies to a good approximation whenever thermal equilibrium fluctuations of fundamental variables like energy and pressure are strongly correlated. Results from computer simulations showing that this is the case for a number of simple glass-forming liquids, as well as a few exceptions, are briefly presented. Finally, we discuss a new conjecture according to which experiments at varying temperature and pressure follow the density-scaling expression for the relaxation time, $\tau=F(\rho^x/T)$ ($\rho$ and $T$ are density and temperature), if and only if the liquid is "strongly correlating," i.e., to a good approximation is described by a single "order" parameter.

(Abridged, full abstract available in the text) The main goal of the study presented in this thesis was to perform in-situ investigations on deformation structures in plastically deformed polycrystalline copper at low degrees (<5%) of tensile deformation. Copper is taken as a model system for pure fcc metals. A novel synchrotron-radiation based technique has been developed. The technique allows for in-situ 3D reciprocal space mapping of reflections from deeply-embedded individual grains in polycrystalline samples during tensile deformation. We have shown that the resulting 3D maps from copper, consists of bright sharp peaks superimposed on a cloud of enhanced intensity. It is concluded that the individual peaks arise from the individual dislocation-free regions (the subgrains) in the dislocation structure. Based on data taken under static load, the strain distribution in and between the individual subgrains is analyzed and compared to composite type models. The consequences of stress relaxation and unloading is moreover discussed. The dynamics of the dislocation structure are investigated by continuous and stepwise deformation experiments. On the basis of such data the unset of subgrain formation and the subgrain refinement process is analyzed., Comment: Ph.D. thesis, 120 pages, 45 figures