Search

About one hundred magnets of six different types shall be installed in the High Luminosity LHC (HL-LHC) in the years 2026-2028 at CERN. The magnets design, construction and test are based on CERN collaborations with institutes and industrial partners in USA, Spain, Italy, Japan and China. Three types of correctors are based on Nb‒Ti technology and feature conductor peak fields in the 2 to 4 T range: for all of them the prototype phase has been successfully completed. The production is well advanced for the superferric correctors, and is starting for the canted cosine theta correctors and for the nested correctors. The separation and recombination Nb‒Ti dipoles D1 and D2, with a 4.5-6 T bore field range, are both in the prototype phase after the completion of the short model program. The most challenging magnet, the Nb3Sn quadrupole with conductor peak field above 11 T, is in the prototype phase at CERN and halfway through the production phase in the USA. In this paper we will give, for each type of magnet, an overview of the main achievements obtained so far and we will outline the technical points still needing validation from the prototype program.

The High-Luminosity project (HL-LHC) of the CERN Large Hadron Collider (LHC), requires low β* quadrupole magnets in Nb$_3$Sn technology that will be installed on each side of the ATLAS and CMS experiments. After a successful shortmodel magnet manufacture and test campaign, the project has advanced with the production, assembly, and test of full-size 7.15- m-long magnets. In the last two years, two CERN-built prototypes (MQXFBP1 and MQXFBP2) have been tested and magnetically measured at the CERN SM18 test facility. These are the longest accelerator magnets based on Nb$_3$Sn technology built and tested to date. In this paper, we present the test and analysis results of these two magnets, with emphasis on quenches and training, voltage-current measurements and the quench localization with voltage taps and a new quench antenna.

A conceptual design is presented of a novel ERL facility for the development and application of the energy recovery technique to linear electron accelerators in the multi-turn, large current and large energy regime. The main characteristics of the powerful energy recovery linac experiment facility (PERLE) are derived from the design of the Large Hadron electron Collider, an electron beam upgrade under study for the LHC, for which it would be the key demonstrator. PERLE is thus projected as a facility to investigate efficient, high current (> 10 mA) ERL operation with three re-circulation passages through newly designed SCRF cavities, at 801.58 MHz frequency, and following deceleration over another three re-circulations. In its fully equipped configuration, PERLE provides an electron beam of approximately 1 GeV energy. A physics programme possibly associated with PERLE is sketched, consisting of high precision elastic electron-proton scattering experiments, as well as photo-nuclear reactions of unprecedented intensities with up to 30 MeV photon beam energy as may be obtained using Fabry-Perot cavities. The facility has further applications as a general technology test bed that can investigate and validate novel superconducting magnets (beam induced quench tests) and superconducting RF structures (structure tests with high current beams, beam loading and transients). Besides a chapter on operation aspects, the report contains detailed considerations on the choices for the SCRF structure, optics and lattice design, solutions for arc magnets, source and injector and on further essential components. A suitable configuration derived from the here presented design concept may next be moved forward to a technical design and possibly be built by an international collaboration which is being established., 112 pages, 63 figures

The interconnections between Large Hadron Collider (LHC) main dipole and quadrupole magnets are made of soldered joints of two superconducting cables stabilized by a copper bus bar. The 2008 incident revealed the possible presence of defects in the interconnections of the 13 kA circuits that could lead to unprotected resistive transitions. Since then thorough experimental and numerical investigations were undertaken to determine the safe operating conditions for the LHC. This paper reports the analysis of experimental tests reproducing defective interconnections between main quadrupole magnets. A thermo-electromagnetic model was developed taking into account the complicated sample geometry. Close attention was paid to the physical description of the heat transfer towards helium, one of the main unknown parameters. The simulation results are reported in comparison with the measurements in case of static He I cooling bath. The outcome of this study constitutes a useful input to improve the stability assessment of the 13 kA bus bars interconnections.