Search

Materials with chiral electronic structures are of great interest. We report a triazatruxene, TAT, molecular semiconductor with chiral alkyl side chains that crystallises from solution to form chirally-stacked columns with a helical pitch of 6 TATs (2.3 nm). These crystals show strong circularly polarised, CP, green photoluminescence, with dissymmetry of 24%. Electronic structure calculations using the full crystal structure, show that this chiral stacking associates angular momentum to the valence and conduction states and thus gives rise to the observed CP luminescence. Free-standing crystals are not useful for active semiconductor devices, but we have discovered that co-sublimation of TAT as the guest in a structurally mismatched host enables the fabrication of thin films where the chiral crystallization is achieved in-situ by thermally-triggered nano-phase segregation of dopant and host whilst preserving the integrity of the film. This enables fabrication of bright (green) organic light-emitting diodes with unexpectedly high external quantum efficiencies of up to 16% and electroluminescence dissymmetries above 10%. These materials and this process method offer significant application potential in spintronics, optical displays and multidimensional optoelectronics.

Optical control and read-out of the ground state spin structure has been demonstrated for defect states in crystalline semiconductors, including the diamond NV- center, and these are promising systems for quantum technologies. Molecular organic semiconductors offer synthetic control of spin placement, in contrast to current limitations in these crystalline systems. Here we report the discovery of spin-optical addressability in a diradical molecule that comprises two trityl radical groups coupled via a fluorene bridge. We demonstrate the three important properties that enable operation as a spin-photon interface: (i) triplet and singlet spin states show photoluminescence peaked at 640 and 700 nm respectively; this allows easy optical measurement of ground state spin. (ii) the ground state spin exchange is small (~60 {\mu}eV) that allows preparation of ground state spin population. This can be achieved by spin-selective excited state intersystem crossing, and we report up to 8% microwave-driven contrast in photoluminescence. (iii) both singlet and triplet manifolds have near-unity photoluminescence quantum yield, which is in contrast to the near-zero quantum yields in prior reports of molecular diradicals. Our results establish these tuneable open-shell organic molecules as a platform to engineer tailor-made spin-optical interfaces.

Photovoltaics (PVs) are a critical technology for curbing growing levels of anthropogenic greenhouse gas emissions, and meeting increases in future demand for low-carbon electricity. In order to fulfil ambitions for net-zero carbon dioxide equivalent (CO2eq) emissions worldwide, the global cumulative capacity of solar PVs must increase by an order of magnitude from 0.9 TWp in 2021 to 8.5 TWp by 2050 according to the International Renewable Energy Agency, which is considered to be a highly conservative estimate. In 2020, the Henry Royce Institute brought together the UK PV community to discuss the critical technological and infrastructure challenges that need to be overcome to address the vast challenges in accelerating PV deployment. Herein, we examine the key developments in the global community, especially the progress made in the field since this earlier roadmap, bringing together experts primarily from the UK across the breadth of the photovoltaics community. The focus is both on the challenges in improving the efficiency, stability and levelized cost of electricity of current technologies for utility-scale PVs, as well as the fundamental questions in novel technologies that can have a significant impact on emerging markets, such as indoor PVs, space PVs, and agrivoltaics. We discuss challenges in advanced metrology and computational tools, as well as the growing synergies between PVs and solar fuels, and offer a perspective on the environmental sustainability of the PV industry. Through this roadmap, we emphasize promising pathways forward in both the short- and long-term, and for communities working on technologies across a range of maturity levels to learn from each other., Comment: 160 pages, 21 figures

The development of luminescent organic radicals has resulted in materials with excellent optical properties for near-infrared (NIR) emission. Applications of light generation in this range span from bioimaging to surveillance. Whilst the unpaired electron arrangements of radicals enable efficient radiative transitions within the doublet-spin manifold in organic light-emitting diodes (OLEDs), their performance is limited by non-radiative pathways introduced in electroluminescence. Here, we present a host:guest design for OLEDs that exploits energy transfer with demonstration of up to 9.6% external quantum efficiency (EQE) for 800 nm emission. The tris(2,4,6-trichlorophenyl)methyl-triphenylamine (TTM-TPA) radical guest is energy-matched to the triplet state in a charge-transporting anthracene-derivative host. We show from optical spectroscopy and quantum-chemical modelling that reversible host-guest triplet-doublet energy transfer allows efficient harvesting of host triplet excitons.

The family of hybrid organic-inorganic lead-halide perovskites are the subject of intense interest for optoelectronic applications, from light-emitting diodes to photovoltaics to X-ray detectors. Due to the inert nature of most organic molecules, the inorganic sublattice generally dominates the electronic structure and therefore optoelectronic properties of perovskites. Here, we use optically and electronically active carbazole-based Cz-Ci molecules, where Ci indicates an alkylammonium chain and i indicates the number of CH2 units in the chain, varying from 3-5, as cations in the 2D perovskite structure. By investigating the photophysics and charge transport characteristics of (Cz-Ci)2PbI4, we demonstrate a tunable electronic coupling between the inorganic lead-halide and organic layers. The strongest interlayer electronic coupling was found for (Cz-C3)2PbI4, where photothermal deflection spectroscopy results remarkably demonstrate an organic-inorganic charge transfer state. Ultrafast transient absorption spectroscopy measurements demonstrate ultrafast hole transfer from the photoexcited lead-halide layer to the Cz-Ci molecules, the efficiency of which increases by varying the chain length from i=5 to i=3. The charge transfer results in long-lived carriers (10-100 ns) and quenched emission, in stark contrast with the fast (sub-ns) and efficient radiative decay of bound excitons in the more conventional 2D perovskite (PEA)2PbI4, in which phenylethylammonium (PEA) acts as an inert spacer. Electrical charge transport measurements further support enhanced interlayer coupling, showing increased out-of-plane carrier mobility from i=5 to i=3. This study paves the way for the rational design of 2D perovskites with combined inorganic-organic electronic proper-ties through the wide range of functionalities available in the world of organics., Comment: 16 main text pages + 20 supplemental text pages, 5 main text figures + 19 supplemental figures

In this study, we develop a steady state and time-dependent exciton diffusion model including singlet and triplet excitons coupled with a modified Poisson and drift-diffusion solver to explain the mechanism of hyper triplet-triplet fusion (TTF) organic light-emitting diodes (OLEDs). Using this modified simulator, we demonstrate various characteristics of OLEDs, including the J-V curve, internal quantum efficiency, transient spectrum, and electric profile. This solver can also be used to explain the mechanism of hyper-TTF-OLEDs and analyze the loss from different exciton mechanisms. Furthermore, we perform additional optimization of hyper-TTF-OLEDs that increases the internal quantum efficiency by approximately 33% (from 29% to 40%).

Molecules present a versatile platform for quantum information science, and are candidates for sensing and computation applications. Robust spin-optical interfaces are key to harnessing the quantum resources of materials. To date, carbon-based candidates have been non-luminescent, which prevents optical read-out. Here we report the first organic molecules displaying both efficient luminescence and near-unity generation yield of high-spin multiplicity excited states. This is achieved by designing an energy resonance between emissive doublet and triplet levels, here on covalently coupled tris(2,4,6-trichlorophenyl) methyl-carbazole radicals (TTM-1Cz) and anthracene. We observe the doublet photoexcitation delocalise onto the linked acene within a few picoseconds and subsequently evolve to a pure high spin state (quartet for monoradicals, quintet for biradical) of mixed radical-triplet character near 1.8 eV. These high-spin states are coherently addressable with microwaves even at 295 K, with optical read-out enabled by intersystem crossing to emissive states. Furthermore, for the biradical, on return to the ground state the previously uncorrelated radical spins either side of the anthracene show strong spin correlation. Our approach simultaneously supports a high efficiency of initialisation, spin manipulations and light-based read-out at room temperature. The integration of luminescence and high-spin states creates an organic materials platform for emerging quantum technologies.

Nanoribbons - nanometer wide strips of a two-dimensional material - are a unique system in condensed matter physics. They combine the exotic electronic structures of low-dimensional materials with an enhanced number of exposed edges, where phenomena including ultralong spin coherence times, quantum confinement and topologically protected states can emerge. An exciting prospect for this new material concept is the potential for both a tunable semiconducting electronic structure and magnetism along the nanoribbon edge. This combination of magnetism and semiconducting properties is the first step in unlocking spin-based electronics such as non-volatile transistors, a route to low-energy computing, and has thus far typically only been observed in doped semiconductor systems and/or at low temperatures. Here, we report the magnetic and semiconducting properties of phosphorene nanoribbons (PNRs). Static (SQUID) and dynamic (EPR) magnetization probes demonstrate that at room temperature, films of PNRs exhibit macroscopic magnetic properties, arising from their edge, with internal fields of ~ 250 to 800 mT. In solution, a giant magnetic anisotropy enables the alignment of PNRs at modest sub-1T fields. By leveraging this alignment effect, we discover that upon photoexcitation, energy is rapidly funneled to a dark-exciton state that is localized to the magnetic edge and coupled to a symmetry-forbidden edge phonon mode. Our results establish PNRs as a unique candidate system for studying the interplay of magnetism and semiconducting ground states at room temperature and provide a stepping-stone towards using low-dimensional nanomaterials in quantum electronics., Comment: 18 pages, 4 figures

Small molecule organic semiconductors hold great promise for efficient, printable, and flexible optoelectronic applications like solar cells and displays. However, strong excited-state quenching due to uncontrolled aggregation currently limits their performance and employability in devices. Here, we report on the self-assembly of a supramolecular pseudo-cube formed from six modified tetradentate perylene diimides (PDIs). The rigid, shape-persistent cage sets the distance and orientation of the PDI chromophores and suppresses intramolecular rotations and vibrations, leading to non-aggregated, monomer-like electronic properties in solution as well as in the solid state, in contrast to the fast fluorescence quenching in the free ligand. The stabilized excited state and electronic purity of the cage enable the observation of delayed fluorescence due to a bright excited multimer state, which acts as an excited state reservoir, due to a rare case of benign inter-chromophore interactions in the cage. Our results suggest that not only the photophysical properties of the subcomponents but the geometric structure is crucial for the overall optoelectronic properties of supramolecular systems. We show that self-assembly provides a powerful tool for retaining and controlling the electronic properties of well-studied chromophores, providing a route to bring molecular electronics applications in reach.

Bandgap tunability of lead mixed-halide perovskites makes them promising candidates for various applications in optoelectronics since they exhibit sharp optical absorption onsets despite the presence of disorder from halide alloying. Here we use localization landscape theory to reveal that the static disorder due to compositional alloying for iodide:bromide perovskite contributes at most 3 meV to the Urbach energy. Our modelling reveals that the reason for this small contribution is due to the small effective masses in perovskites, resulting in a natural length scale of around 20nm for the "effective confining potential" for electrons and holes, with short range potential fluctuations smoothed out. The increase in Urbach energy across the compositional range agrees well with our optical absorption measurements. We model systems of sizes up to 80 nm in three dimensions, allowing us to explore halide segregation, accurately reproducing the experimentally observed absorption spectra and demonstrating the scope of our method to model electronic structures on large length scales. Our results suggest that we should look beyond static contribution and focus on the dynamic temperature dependent contribution to the Urbach energy., Comment: 4 figures

Photosystems II and I (PSII and PSI) are the reaction centre complexes that drive the light reactions of photosynthesis. PSII performs light-driven water oxidation (quantum efficiencies and catalysis rates of up to 80% and 1000 $e^{-}\text{s}^{-1}$, respectively) and PSI further photo-energises the harvested electrons (quantum efficiencies of ~100%). The impressive performance of the light harvesting components of photosynthesis has motivated extensive biological, artificial and biohybrid approaches to re-wire photosynthesis to enable higher efficiencies and new reaction pathways, such as H2 evolution or alternative CO2 fixation. To date these approaches have focussed on charge extraction at the terminal electron quinones of PSII and terminal iron-sulfur clusters of PSI. Ideally electron extraction would be possible immediately from the photoexcited reaction centres to enable the greatest thermodynamic gains. However, this was believed to be impossible because the reaction centres are buried around 4 nm within PSII and 5 nm within PSI from the cytoplasmic face. Here, we demonstrate using in vivo ultrafast transient absorption (TA) spectroscopy that it is possible to extract electrons directly from photoexcited PSI and PSII, using both live cyanobacterial cells and isolated photosystems, with the exogenous electron mediator 2,6-dichloro1,4-benzoquinone (DCBQ). We postulate that DCBQ can oxidise peripheral chlorophyll pigments participating in highly delocalised charge transfer (CT) states after initial photoexcitation. Our results open new avenues to study and re-wire photosynthesis for bioenergy and semi-artificial photosynthesis.

Organic solar cells (OSCs) have recently shown a rapid improvement in their performance, bringing power conversion efficiencies (PCEs) closer to the point where commercial applications of the technology become viable. However, the low open-circuit voltage (Voc) of OSCs relative to their optical gap still limits PCEs to below 20%. A key factor contributing to the large Voc deficit in OSCs is non-radiative recombination to spin-triplet excitons, which is widely, but not universally, observed in blends using both fullerene and non-fullerene electron acceptors. Here, we present an experimental framework that combines time resolved optical and magnetic resonance spectroscopies to detect triplet excitons and identify their formation mechanisms. We apply our methodology to two well-studied polymer:fullerene systems, PM6:PC60BM and PTB7-Th:PC60BM, enabling us to selectively investigate distinct triplet formation pathways. In contrast to the more efficient non-fullerene acceptor systems that show only triplet states formed via non-geminate recombination, the fullerene systems also show significant triplet formation via geminate processes. We associate this with electrons trapped at the isolated fullerenes that sit within the alkyl sidechains of the donor polymers. Thus, our model study demonstrates how these complex and overlapping processes can be successfully deconvoluted to reveal the intricacies of triplet generation dynamics in OSC blends., Comment: 64 pages, 4 main-text figures

Organic light-emitting diodes (OLEDs) must be engineered to circumvent the efficiency limit imposed by the 3:1 ratio of triplet to singlet exciton formation following electron-hole capture. Here we show the spin nature of luminescent radicals such as TTM-3PCz allows direct energy harvesting from both singlet and triplet excitons through energy transfer, with subsequent rapid and efficient light emission from the doublet excitons. This is demonstrated with a model Thermally-Activated Delayed Fluorescence (TADF) organic semiconductor, 4CzIPN, where reverse intersystem crossing from triplets is characteristically slow (50% emission by 1 microsecond). The radical:TADF combination shows much faster emission via the doublet channel (80% emission by 100 ns) than the comparable TADF-only system, and sustains higher electroluminescent efficiency with increasing current density than a radical-only device. By unlocking energy transfer channels between singlet, triplet and doublet excitons, further technology opportunities are enabled for optoelectronics using organic radicals., Comment: 35 pages, 4 figures in main text and 11 figures in Supplementary Information

Thermally-activated delayed fluorescence (TADF) enables organic semiconductors with charge transfer (CT)-type excitons to convert dark triplet states into bright singlets via a reverse intersystem crossing (rISC) process. Here, we consider the role of the dielectric environment in a range of TADF materials with varying changes in dipole moment upon optical excitation. In a dipolar reference emitter, TXO-TPA, environmental reorganisation after excitation in both solution and doped films triggers the formation of the full CT product state. This lowers the singlet excitation energy by 0.3 eV and minimises the singlet-triplet energy gap ({\Delta}EST). Using impulsive Raman measurements, we observe the emergence of two (reactant-inactive) modes at 412 and 813 cm-1 as a vibrational fingerprint of the CT product. In contrast, the dielectric environment plays a smaller role in the electronic excitations of a less dipolar material, 4CzIPN. Quantum-chemical calculations corroborate the appearance of these new product modes in TXO-TPA and show that the dynamic environment fluctuations are large compared to {\Delta}EST. The analysis of the energy-time trajectories and the corresponding free energy functions reveals that the dielectric environment significantly reduces the activation energy for rISC, thus increasing the rISC rate by up to three orders of magnitude when compared to a vacuum environment., Comment: 67 pages, 7 main-text figures

The radiative recombination of injected charge carriers gives rise to electroluminescence (EL), a central process for light-emitting diode (LED) operation. It is often presumed in some emerging fields of optoelectronics, including perovskite and organic LEDs, that the minimum voltage required for light emission is the semiconductor bandgap divided by the elementary charge. Here we show for many classes of LEDs, including those based on metal halide perovskite, organic, chalcogenide quantum-dot and commercial III-V semiconductors, photon emission can be generally observed at record-low driving voltages of 36%-60% of their bandgaps, corresponding to a large apparent energy gain of 0.6-1.4 eV per emitted photon. Importantly, for various classes of LEDs with very different modes of charge injection and recombination (dark saturation current densities ranging from ~10^-35 to ~10^-21 mA/cm2), their EL intensity-voltage curves under low voltages exhibit similar behaviors, revealing a universal origin of ultralow-voltage device operation. Finally, we demonstrate as a proof-of-concept that perovskite LEDs can transmit data efficiently to a silicon detector at 1V, a voltage below the silicon bandgap. Our work provides a fresh insight into the operational limits of electroluminescent diodes, highlighting the significant potential of integrating low-voltage LEDs with silicon electronics for next-generation communications and computational applications.

Engineering a low singlet-triplet energy gap ({\Delta}EST) is necessary for efficient reverse intersystem crossing (rISC) in delayed fluorescence (DF) organic semiconductors, but results in a small radiative rate that limits performance in LEDs. Here, we study a model DF material, BF2, that exhibits a strong optical absorption (absorption coefficient =3.8x10^5 cm^-1) and a relatively large {\Delta}EST of 0.2 eV. In isolated BF2 molecules, intramolecular rISC is slow (260 {\mu}s), but in aggregated films, BF2 generates intermolecular CT (inter-CT) states on picosecond timescales. In contrast to the microsecond intramolecular rISC that is promoted by spin-orbit interactions in most isolated DF molecules, photoluminescence-detected magnetic resonance shows that these inter-CT states undergo rISC mediated by hyperfine interactions on a ~24 ns timescale and have an average electron-hole separation of >1.5 nm. Transfer back to the emissive singlet exciton then enables efficient DF and LED operation. Thus, access to these inter-CT states resolves the conflicting requirements of fast radiative emission and low {\Delta}EST., Comment: 102 pages, 4 main-text figures

The Shockley-Queisser (SQ) limit, introduced by W. Shockley and H. J. Queisser in 1961, is the most well-established fundamental efficiency limit for single-junction photovoltaic solar cells. For widely-studied semiconductors such as Si, GaAs and lead-halide perovskite, the SQ limits under standard solar illumination (1-sun) are 32.7%, 32.5% and 31% for bandgaps of 1.12 eV, 1.43 eV and 1.55 eV, respectively. Here, we propose that the fundamental efficiency limits for single-junction solar cells may be surpassed via photon confinement, substantially raising the theoretical limits to 49%, 45.2% and 42.1% for Si, GaAs and methylammonium lead iodide (MAPbI3) perovskite cells under 1-sun. Such enhancement is possible through the containment of luminescent photons within the solar cell, allowing the suppression of both non-radiative and radiative recombination losses, which were considered inevitable in the classical SQ model. Importantly, restricting photon emission from the solar cells raises the open-circuit voltage (VOC) to values approaching the semiconductor bandgaps, surpassing the theoretical VOC values predicted by the SQ model. The fill factors of the cells are expected to increase substantially, resulting in current-voltage characteristics with very-high squareness for ideal diode operation. Our work introduces a new framework for improving solar cell performance beyond the conventional limits.

Perovskite nanoplatelets (NPls) hold great promise for light-emitting applications, having achieved high photoluminescence quantum efficiencies (PLQEs) approaching unity in the blue wavelength range, where other metal-halide perovskites have typically been ineffective. However, the external quantum efficiency (EQE) of blue-emitting NPl light-emitting diodes (LEDs) have only reached 0.12%, with typical values well below 0.1%. In this work, we show that the performance of NPl LEDs is primarily hindered by a poor electronic interface between the emitter and hole-injector. Through Kelvin Probe and X-ray photoemission spectroscopy measurements, we reveal that the NPls have remarkably deep ionization potentials (>=6.5 eV), leading to large barriers for hole injection, as well as substantial non-radiative decay at the interface between the emitter and hole-injector. We find that an effective way to reduce these non-radiative losses is by using poly(triarylamine) interlayers. This results in an increase in the EQE of our blue LEDs emitting at 464 nm wavelength to 0.3%. We find that our results can be generalized to thicker sky-blue-emitting NPls, where we increase the EQE to 0.55% using the poly(triarylamine) interlayer. Our work also identifies the key challenges for further efficiency increases.

The power conversion efficiencies (PCEs) of organic solar cells (OSCs) using non-fullerene acceptors (NFAs) have now reached 18%. However, this is still lower than inorganic solar cells, for which PCEs >20% are commonplace. A key reason is that OSCs still show low open-circuit voltages (Voc) relative to their optical band gaps, attributed to non-radiative recombination. For OSCs to compete with inorganics in efficiency, all non-radiative loss pathways must be identified and where possible, removed. Here, we show that in most NFA OSCs, the majority of charge recombination at open-circuit proceeds via formation of non-emissive NFA triplet excitons (T1); in the benchmark PM6:Y6 blend, this fraction reaches 90%, contributing 60 mV to the reduction of Voc. We develop a new design to prevent recombination via this non-radiative channel through the engineering of significant hybridisation between the NFA T1 and the spin-triplet charge transfer exciton (3CTE). We model that the rate of the back charge transfer from 3CTE to T1 can be reduced by an order of magnitude, allowing re-dissociation of the 3CTE. We then demonstrate NFA systems where T1 formation is suppressed. This work therefore provides a clear design pathway for improved OSC performance to 20% PCE and beyond., Comment: 30 pages, 3 figures, 1 table

Efficient energy transport is highly desirable for organic semiconductor (OSC) devices such as photovoltaics, photodetectors, and photocatalytic systems. However, photo-generated excitons in OSC films mostly occupy highly localized states over their lifetime. Energy transport is hence thought to be mainly mediated by the site-to-site hopping of localized excitons, limiting exciton diffusion coefficients to below ~10^{-2} cm^2/s with corresponding diffusion lengths below ~50 nm. Here, using ultrafast optical microscopy combined with non-adiabatic molecular dynamics simulations, we present evidence for a new highly-efficient energy transport regime: transient exciton delocalization, where energy exchange with vibrational modes allows excitons to temporarily re-access spatially extended states under equilibrium conditions. In films of highly-ordered poly(3-hexylthiophene) nanofibers, prepared using living crystallization-driven self-assembly, we show that this enables exciton diffusion constants up to 1.1+-0.1 cm^2/s and diffusion lengths of 300+-50 nm. Our results reveal the dynamic interplay between localized and delocalized exciton configurations at equilibrium conditions, calling for a re-evaluation of the basic picture of exciton dynamics. This establishes new design rules to engineer efficient energy transport in OSC films, which will enable new devices architectures not based on restrictive bulk heterojunctions., Comment: 61 pages, 4 main figures

Nanocrystals based on metal-halide perovskites offer a promising material platform for highly efficient lighting. Using transient optical spectroscopy, we study excitation recombination dynamics in manganese-doped CsPb(Cl,Br)3 perovskite nanocrystals. We find an increase in the intrinsic excitonic radiative recombination rate upon doping, which is typically a challenging material property to tailor. Supported by ab initio calculations, we can attribute the enhanced emission rates to increased exciton localization through lattice periodicity breaking from Mn dopants, which increases exciton effective masses and overlap of electron and hole wavefunctions and thus the oscillator strength. Our report of a fundamental strategy for improving luminescence efficiencies in perovskite nanocrystals will be valuable for maximizing efficiencies in light-emitting applications.

Bulk-heterojunction (BHJ) non-fullerene organic solar cells prepared from sequentially deposited donor and acceptor layers (sq-BHJ) have recently been promising to be highly efficient, environmentally friendly, and compatible with large area and roll-to-toll fabrication. However, the related photophysics at donor-acceptor interface and the vertical heterogeneity of donor-acceptor distribution, critical for exciton dissociation and device performance, are largely unexplored. Herein, steady-state and time-resolved optical and electrical techniques are employed to characterize the interfacial trap states. Correlation with the luminescent efficiency of interfacial states and its non-radiative recombination, interfacial trap states are characterized to be about 50% more populated in the sq-BHJ than as-cast BHJ (c-BHJ), which probably limits the device voltage output. Cross-sectional energy-dispersive X-ray spectroscopy and ultraviolet photoemission spectroscopy depth profiling directly vizualize the donor-acceptor vertical stratification with a precision of 1-2 nm. From the proposed "needle" model, the high exciton dissociation efficiency is rationalized. Our study highlights the promise of sequential deposition to fabricate efficient solar cells, and points towards improving the voltage output and overall device performance via eliminating interfacial trap states.

Energy level diagrams in organic electronic devices play a crucial role in device performance and interpretation of device physics. In the case of organic solar cells, it has become routine to estimate the photovoltaic gap of the donor:acceptor blend using the energy values measured on the individual blend components, resulting in a poor agreement with the corresponding open-circuit voltage of the device. To address this issue, we developed a method that allows a direct visualisation of the vertical energetic landscape in the blend, obtained by combining ultraviolet photoemission spectroscopy and argon cluster etching. We investigate both model and high-performance photovoltaic systems and demonstrate that the resulting photovoltaic gaps are in close agreement with the measured CT energies and open-circuit voltages. Furthermore, we show that this method allows us to study the evolution of the energetic landscape upon environmental degradation, critically important for understanding degradation mechanisms and development of mitigation strategies.

Halide double perovskites have gained significant attention, owing to their composition of low-toxicity elements, stability in air and long charge-carrier lifetimes. However, most double perovskites, including Cs2AgBiBr6, have wide bandgaps, which limit photo conversion efficiencies. The bandgap can be reduced through hallowing with Sb3+, but Sb-rich alloys are difficult to synthesise due to the high formation energy of Cs2AgSbBr6, which itself has a wide bandgap. We develop a solution-based route to synthesis phase-pure Cs2Ag(SbxBi1-x)Br6 thin films, with the mixing parameter x continuous varying over the entire composition range. We reveal that the mixed alloys (x between 0.5 and 0.9) demonstrate smaller bandgaps (as low as 2.08 eV) than the pure Sb- (2.18 eV) and Bi-based (2.25 eV) compounds, with strong deviation from Vegard's law. Through in-depth computations, we propose that bandgap lowering arises from the Type II band alignment between Cs2AgBiBr6 and Cs2AgSbBr6. The energy mismatch between the Bi and Sb s and p atomic orbitals, coupled with their non-linear mixing, results in the alloys adopting a smaller bandgap than the pure compounds. Our work demonstrates an approach to achieve bandgap reduction and highlights that bandgap bowing may be found in other double perovskite alloys by pairing together materials forming a Type II band alignment., Comment: 28 pages, 4 figures

Organic semiconductors exhibit properties of individual molecules and extended crystals simultaneously. The strongly bound excitons they host are typically described in the molecular limit, but excitons can delocalize over many molecules, raising the question of how important the extended crystalline nature is. Using accurate Green's function based methods for the electronic structure and non-perturbative finite difference methods for exciton-vibration coupling, we describe exciton interactions with molecular and crystal degrees of freedom concurrently. We find that the degree of exciton delocalization controls these interactions, with thermally activated crystal phonons predominantly coupling to delocalized states, and molecular quantum fluctuations predominantly coupling to localized states. Based on this picture, we quantitatively predict and interpret the temperature and pressure dependence of excitonic peaks in the acene series of organic semiconductors, which we confirm experimentally, and we develop a simple experimental protocol for probing exciton delocalization. Overall, we provide a unified picture of exciton delocalization and vibrational effects in organic semiconductors, reconciling the complementary views of finite molecular clusters and periodic molecular solids.

Organic solar cells (OSCs) based on non-fullerene acceptors can show high charge generation yields despite near-zero donor-acceptor energy offsets to drive charge separation and overcome the mutual Coulomb attraction between electron and hole. Here we use time-resolved optical spectroscopy to show that free charges in these systems are generated by thermally activated dissociation of interfacial charge-transfer excitons (CTEs) that occurs over hundreds of picoseconds at room temperature, three orders of magnitude slower than comparable fullerene-based systems. Upon free electron-hole encounters at later times, CTEs and emissive excitons are regenerated, thus setting up an equilibrium between excitons, CTEs and free charges. This endothermic charge separation process enables these systems to operate close to quasi-thermodynamic equilibrium conditions with no requirement for energy offsets to drive charge separation and achieve greatly suppressed non-radiative recombination., Comment: 30 pages, 4 figures

Luminescent colloidal CdSe nanorings are a new type of semiconductor structure that have attracted interest due to the potential for unique physics arising from their non-trivial toroidal shape. However, the exciton properties and dynamics of these materials with complex topology are not yet well understood. Here, we use a combination of femtosecond vibrational spectroscopy, temperature-resolved photoluminescence (PL), and single particle measurements to study these materials. We find that on transformation of CdSe nanoplatelets to nanorings, by perforating the center of platelets, the emission lifetime decreases and the emission spectrum broadens due to ensemble variations in the ring size and thickness. The reduced PL quantum yield of nanorings (~10%) compared to platelets (~30%) is attributed to an enhanced coupling between: (i) excitons and CdSe LO-phonons at 200 cm-1 and (ii) negatively charged selenium-rich traps which give nanorings a high surface charge (~-50 mV). Population of these weakly emissive trap sites dominates the emission properties with an increased trap emission at low temperatures relative to excitonic emission. Our results provide a detailed picture of the nature of excitons in nanorings and the influence of phonons and surface charge in explaining the broad shape of the PL spectrum and the origin of PL quantum yield losses. Furthermore, they suggest that the excitonic properties of nanorings are not solely a consequence of the toroidal shape but are also a result of traps introduced by puncturing the platelet center., Comment: 38 pages, 10 figures

Electroluminescence (EL) of colloidal nanocrystals promises a new generation of high-performance and solution-processable light-emitting diodes (LEDs). The operation of nanocrystal-based LEDs relies on the recombination of electrically-generated excitons. However, a fundamental question, i.e, how excitons are electrically generated in individual nanocrystals, remains unanswered. Here, we reveal a molecular mechanism of sequential electron-hole injection for the exciton generation in nanocrystal-based EL devices. To decipher the corresponding elementary processes, we develop electrically-pumped single-nanocrystal spectroscopy. While hole injection into neutral quantum dots (QDs) is generally-considered to be inefficient, we find that the intermediate negatively-charged state of QD triggers confinement-enhanced Coulomb interactions, which simultaneously accelerate hole injection and hinder excessive electron injection. In-situ/operando spectroscopy on state-of-the-art QD-LEDs demonstrate that exciton generation at the ensemble level is consistent with the charge-confinement-enabled sequential electron-hole injection mechanism revealed at the single-nanocrystal level. Our findings provide a universal mechanism for enhancing charge balance in nanocrystal-based EL devices.

The formation of exciton-polaritons allows the transport of energy over hundreds of nanometres at velocities up to 10^6 m s^-1 in organic semiconductors films in the absence of external cavity structures.

Perovskite-based optoelectronic devices have gained significant attention due to their remarkable performance and low processing cost, particularly for solar cells. However, for perovskite light-emitting diodes (LEDs), non-radiative charge carrier recombination has limited electroluminescence (EL) efficiency. Here we demonstrate perovskite-polymer bulk heterostructure LEDs exhibiting record-high external quantum efficiencies (EQEs) exceeding 20%, and an EL half-life of 46 hours under continuous operation. This performance is achieved with an emissive layer comprising quasi-2D and 3D perovskites and an insulating polymer. Transient optical spectroscopy reveals that photogenerated excitations at the quasi-2D perovskite component migrate to lower-energy sites within 1 ps. The dominant component of the photoluminescence (PL) is primarily bimolecular and is characteristic of the 3D regions. From PL quantum efficiency and transient kinetics of the emissive layer with/without charge-transport contacts, we find non-radiative recombination pathways to be effectively eliminated. Light outcoupling from planar LEDs, as used in OLED displays, generally limits EQE to 20-30%, and we model our reported EL efficiency of over 20% in the forward direction to indicate the internal quantum efficiency (IQE) to be close to 100%. Together with the low drive voltages needed to achieve useful photon fluxes (2-3 V for 0.1-1 mA/cm2), these results establish that perovskite-based LEDs have significant potential for light-emission applications.

From organic electronics to biological systems, understanding the role of intermolecular interactions between spin pairs is a key challenge. Here we show how such pairs can be selectively addressed with combined spin and optical sensitivity. We demonstrate this for bound pairs of spin-triplet excitations formed by singlet fission, with direct applicability across a wide range of synthetic and biological systems. We show that the site-sensitivity of exchange coupling allows distinct triplet pairs to be resonantly addressed at different magnetic fields, tuning them between optically bright singlet (S=0) and dark triplet, quintet (S=1,2) configurations: this induces narrow holes in a broad optical emission spectrum, uncovering exchange-specific luminescence. Using fields up to 60 T, we identify three distinct triplet-pair sites, with exchange couplings varying over an order of magnitude (0.3-5 meV), each with its own luminescence spectrum, coexisting in a single material. Our results reveal how site-selectivity can be achieved for organic spin pairs in a broad range of systems., Comment: 8 pages, article, 7 pages, supporting information

Halide perovskites are promising semiconductors for inexpensive, high-performance optoelectronics. Despite a remarkable defect tolerance compared to conventional semiconductors, perovskite thin films still show substantial microscale heterogeneity in key properties such as luminescence efficiency and device performance. This behavior has been attributed to spatial fluctuations in the population of sub-bandgap electronic states that act as trap-mediated non-radiative recombination sites. However, the origin of the variations, trap states and extent of the defect tolerance remains a topic of debate, and a precise understanding is critical to the rational design of defect management strategies. By combining scanning X-ray diffraction beamlines at two different synchrotrons with high-resolution transmission electron microscopy, we reveal levels of heterogeneity on the ten-micrometer scale (super-grains) and even ten-nanometer scale (sub-grain domains). We find that local strain is associated with enhanced defect concentrations, and correlations between the local structure and time-resolved photoluminescence reveal that these strain-related defects are the cause of non-radiative recombination. We reveal a direct connection between defect concentrations and non-radiative losses, as well as complex heterogeneity across multiple length scales, shedding new light on the presence and influence of structural defects in halide perovskites.