Search

The eight-chain RF system and radio frequency quadrupole (RFQ) linac were successfully integrated at the facility of the Linear IFMIF Prototype Accelerator (LIPAc). We achieved an unprecedented high current deuteron beam up to 55 mA in pulse operation ( $300~\mu \text{s}$ , 1 Hz). The keys of the success were (1) understanding reflected power from RFQ to RF system, (2) tuning each RF chain individually, (3) intensive RF conditioning for holding the stable RF power in the RFQ, and (4) optimizing the beam loading compensation control. Interestingly, the reflection at the breakdown in RF conditioning was higher than an estimation and reached up to 600 kW so far. In order to avoid damage on tetrodes by the high reflection, the impedance of each circulator was accurately adjusted.

The detailed shielding analysis has been performed in order to find a configuration of the radiation shielding in the accelerator building necessary for the operation of the Linear IFMIF Prototype Accelerator (LIPAc), which is under construction in Rokkasho, Japan, at the full power of 1.125 MW to satisfy the radiation dose limit prescribed by Japanese regulations. The final design of the beam dump constructed by CIEMAT, Spain was fully taken into consideration. The impact of all the features potentially causing neutron streaming were investigated and the optimization of local additional shieldings were conducted. As the result, the most important one was found to be the air ventilation duct shield, which completely covers the ducts and creates an additional labyrinth. By considering the additional shielding configuration determined in the present study, the legal criteria at the controlled area boundary can be completely satisfied.

International audience; Design, development, manufacturing, and test activities of the RF power system (RFPS) for Linear IFMIF Prototype Accelerator (LIPAc) were completed in Europe. Installation and commissioning activities were carried out at the International Fusion Materials Irradiation Facility-Engineering Validation and Engineering Design Activities (IFMIF/EVEDA) site in Rokkasho, Japan. Challenging IFMIF requirements led to a number of innovations during design and development. Commissioning required a major effort on calibration and fine setting and led to development of new functionalities. The RFPS was validated under full power and 125-mA deuteron beam loading conditions, in the radio frequency quadrupole (RFQ), demonstrating good performance. This article is an overview about how technical challenges impacted the prototype RFPS design and its functional evolution during commissioning, cavity conditioning, and beam operation of the RFQ.

The IFMIF accelerator facility consists of 2 identical linacs, each accelerating a 125 mA CW deuteron beam up to the energy of 40 MeV. In order to reach these unprecedented performances, the Linear IFMIF Prototype Accelerator (LIPAc) is under installation and commissioning at the International Fusion Energy Research Centre (IFERC) in Rokkasho, Japan, in the framework of the IFMIF/EVEDA project, which is part of the Broader Approach (BA) agreement between Japan and EU. The accelerator is designed to validate components up to 125 mA CW deuteron beam at 9 MeV. The accelerator components of LIPAc have been designed and manufactured mainly by European Institutes. The injector and superconducting linac, RFQ, MEBT, Diagnostics Plate, HEBT and beam dump have been developed respectively by CEA-Saclay, INFN-Legnaro and CIEMAT-Madrid and were delivered to Rokkasho between 2013 and 2016. The commissioning of the injector with beam started in November 2014. This paper dealt with the experimental data obtained with the beam diagnostics of the injector. The electrical measurements of the beam intensity on the beam stopper were compared with calorimetric measurements. The beam profiles measured with a CCD camera and a custom image-intensified CID camera are also addressed. The analysis of beam emittance and ion species fractions from data obtained with an Allison scanner is described and the results of species fraction measurements are compared with those obtained by using a deported spectrometer. Finally, the analysis of beam space potential from data obtained with a 4-Grid analyser is presented.

The construction of the Linear IFMIF Prototype Accelerator (LIPAc) is in progress in order to demonstrate the feasibility of the low energy section of an IFMIF deuteron accelerator up to 9 MeV with a beam current of 125 mA in CW. The next milestone of the project is the so-called Phase-B beam commissioning, and one of the missions is to demonstrate the acceleration of the proton beam up to 2.5 MeV or the deuteron beam up to 5.0 MeV in pulsed mode with a low duty cycle of 0.1% through RFQ. Most of the components and subsystems necessary for Phase-B were delivered by 2016 under the responsibility of Fusion for Energy (F4E) as in-kind contributions of several European institutes, namely CEA (France), CIEMAT (Spain), INFN (Italy), and SCK-CEN (Belgium), and QST is in charge of the installation of the delivered equipment. The installation and check-out of the RFQ subsystem and the RF power system was completed by July 2017, and the RF conditioning of the RFQ cavity started. Also, the installation and the check-out of the important sub-systems for Phase-B, namely MEBT and beam diagnostics, have been completed. Keywords: IFMIF, LIPAc, RFQ, Accelerator, Deuteron, Neutron source

The Radio Frequency Quadrupole (RFQ) linac and 1.6 MW RF power system of the Linear IFMIF Prototype Accelerator (LIPAc) facility in the International Fusion Energy Research Center (IFERC) in Rokkasho (Japan) has been installed and conditioned. During the assembly and tuning process, the RFQ cavity was protected with a temporary tent from the potential deterioration of performance caused by dust. The vacuum in the cavity was improved through the 100 °C baking process of the cavity. The high power test of the 175 MHz RF systems up to 200 kW in CW for each of the eight RF chains was performed for checking its stable output reproducibility in Japan, before connecting 9–3/16 inch coaxial transmission lines from the RF chains to the RF input couplers of the cavity. It was confirmed that the eight RF chains provided the balanced RF power to the single RFQ cavity in-phase using a feedback loop and a synchronization system. The peak power in the cavity achieved 150 kW in the pulsed mode, which corresponds approximately to the required electric field to accelerate proton beam. Such RF conditioning process is ongoing to achieve 600 kW approximately required for deuteron beam commissioning planned in 2018.

The goal of LIPAc (Linear IFMIF Prototype Accelerator) is to achieve a 125 mA, 9 MeV, CW (continuous wave, i.e. 100% duty cycle) deuteron beam with an average beam power of 1.125 MW. In the beam current mea- surement, it is considered that calorimetric measurement is advantageous for high current and CW operations since it is not subject to secondary electrons, etc. In calorimetric measurements, it is necessary to measure the temperature rise of the cooling water as accurately as possible. We applied this method to LIPAc proton beams at the Beam Stop unit. In order to check the reliability, we inserted a heater in the cooling loop as a heat source and obtained correlation between the applied and measured power, which was found to be 1.0. Moreover, using this heater, accuracy of this measurement with respect to the flow rate of the cooling water was investigated. Due to heat transfer and the fluctuations of water temperature, etc., there is a range of flow rates in which the measurement error can be minimized with our calorimetric measurement system.

The validation of the Linear IFMIF Prototype Accelerator (LIPAc) is being conducted in Rokkasho Fusion Institute of QST, Aomori, Japan. The beam commissioning of the novel LIPAc RFQ has been progressing significantly, and the acceleration of the world highest current deuteron beam of 125 mA to 5 MeV (1 ms, 1 Hz pulsed beam) was achieved for the 1st time in July 2019. This study is devoted to evaluating the amount of beam loss during the high current acceleration phase by measuring the neutron produced by the interaction of the beam with accelerator components so as to verify the accelerator design. The foil activation method and the 3He neutron probes were utilized. It turned out that there was no significant trace of unexpected beam loss at the high energy section of the RFQ and the Medium Energy Beam Transport (MEBT) section.The measurement using the 3He neutron probes provided an evidence that the beam loss was well controlled in the RFQ cavity as designed. This study concludes that the LIPAc RFQ as well as MEBT is working well as predicted by the design calculation, and its concept is successful.

For the development of the International Fusion Materials Irradiation Facility (IFMIF) aiming at material tests for fusion power plants, the construction of the Linear IFMIF Prototype Accelerator (LIPAc) has been conducted at Rokkasho, Japan under the Broader Approach Agreement. The commissioning of LIPAc has been progressing significantly. The world most powerful RFQ successfully accelerated proton beam of 58 mA, and an important project milestone of the acceleration of deuteron beam to 5 MeV with the beam current of 125 mA in pulse mode was successfully achieved. The result proves the validity of the present RFQ design. The adjustment and tuning of the RF power system and the injector for enabling an operation at maximum performances played an important role in achieving this result. For the next step, the preparation of the high duty cycle operation of RFQ is underway. The installation of the HEBT (High Energy Beam Transport line) and the beam dump accepting 1 MW, CW beam, has been completed and a new beam transport line is under manufacturing. Also the assembly of the Superconducting RF (SRF) linac to accelerate the beam up to 9 MeV started in a clean room in Rokkasho.

The Linear IFMIF Prototype Accelerator aims to operate in Rokkasho Fusion Institute a 125 mA/cw deuteron beam at 9 MeV In order to prove the technical feasibility of the IFMIF accelerators concept. A 2.45 GHz ECR ion source developed by CEA-Saclay is designed to deliver 140 mA/100 keV CW D + beam. The low energy beam transfer line (LEBT) relies on a dual solenoid focusing system to transport and match the beam into the next accelerating section which is a Radio-Frequency Quadrupole (RFQ). At the end of the LEBT, the normalized RMS emittance has to be lower than 0.3π mm.mrad in order to reach the optimal beam transmission through the RFQ. This contribution will present the different commissioning phases of LIPAC ion source and LEBT. The experimental results that have been obtained will be reported. In particular, beam emittance measurements as a function of ion source extraction voltage gaps, total extracted current from the source and solenoid tunings will be showed. In order to model as well as possible the beam transport thought LEBT, intensive beam dynamics simulations that take into account space charge compensation have been performed using a self-consistent particle-in-cell code. Simulation results will be discussed and compared to experimental data.

IFMIF, the International Fusion Materials Irradiation Facility, is an accelerator-based neutron source that will use Li(d, xn) reactions to generate a flux of neutrons with a broad peak at 14 MeV equivalent to the conditions of the Deuterium-Tritium reactions in a fusion power plant. IFMIF is conceived for fusion materials testing. The IFMIF prototype linear accelerator (LIPAc) is jointly developed by Europe and Japan within the IFMIF EVEDA project: it is composed of an ion source, a LEBT, an RFQ, a MEBT and a SC linac, with a final energy of 9 MeV. The 4-vane Radio Frequency Quadrupole (RFQ), developed by INFN in Italy, will accelerate a 130 mA deuteron beam from 0.1 to 5 MeV in continuous wave, for a beam power of 650 kW. The 9.8 m long 175 MHz cavity is composed of 18 x 0.54 m long modules flanged together and aligned within 0.3 mm tolerance. The RFQ was completed, delivered and assembled at the Rokkasho site and is presently under extended RF tests. The second phase of beam commissioning (up to 2.5 MeV/u) was scheduled to start at the end of 2017. Several unexpected issues and incidents significantly delayed the original program, which is however proceeding step by step toward the full achievement of its goals., 9th International Particle Accelerator COnference - IPAC2018

The goal of LIPAc (Linear IFMIF Prototype Accelerator) is to achieve a 125 mA, 9 MeV, CW (continuous wave, i.e. 100% duty cycle) deuteron beam with an average beam power of 1.125 MW. In the beam current measurement, it is considered that calorimetric measurement is advantageous for high current and CW operations since it is not subject to secondary electrons, etc. In calorimetric measurements, it is necessary to measure the temperature rise of the cooling water as accurately as possible. We applied this method to LIPAc proton beams at the Beam Stop unit. In order to check the reliability, we inserted a heater in the cooling loop as a heat source and obtained correlation between the applied and measured power, which was found to be 1.0. Moreover, using this heater, accuracy of this measurement with respect to the flow rate of the cooling water was investigated. Due to heat transfer and the fluctuations of water temperature, etc., there is a range of flow rates in which the measurement error can be minimized with our calorimetric measurement system.

During the EVEDA (engineering validation and engineering design activities) phase of the International Fusion Materials Irradiation Facility (IFMIF) project, a 125 mA/9 MeV linear prototype accelerator (LIPAc) has to be built, tested and operated in Rokkasho-mura (Japan). Involved in this project for several years, CEA-Saclay designed the injector of this accelerator which is composed of an electron cyclotron resonance ion source, delivering a 140 mA deuteron beam at 100 keV, and a low energy beam transport (LEBT) line to match the beam for the injection into the radio-frequency quadrupole. In this paper, the components of the LIPAc injector are described. The commissioning of the ion source and LEBT with beam started in November 2014. The different phases of the commissioning are explained and some noticeable experimental results obtained with a beam at 100 keV are presented.

We describe a proposed neutron irradiation facility for studyi ng neutron-i nduced Single Event Effects (SEE) in microelectronic components and systems at the new variable energy high current proton cyclotron (35-70 MeV; 750μA) soon to be operational at LNL. We descri be the progress in designing two neutron production targets to furnish continuous atmospheric-like neutron differential spectra: a W-based thick target (to stop 70 MeV protons), and an innovative composite target made of Beryllium and Tantal um or Lead. We also describe the layout of the facility that will also house quasi-monoenergetic neutron (QMN) and direct proton beam lines. The thick target beam line could be available as soon as the new cyclotron is commissioned. The composite target and QMN beam lines, to be designed in concert, would be completed soon after.