Search

Lithium adsorption on high-surface-area porous carbon (PC) nanomaterials provides superior electrochemical energy storage performance dominated by capacitive behavior. In this study, we demonstrate the influence of structural defects in the graphene lattice on the bonding character of adsorbed lithium. Thermally evaporated lithium was deposited in vacuum on the surface of as-grown graphene-like PC and PC annealed at 400 °C. Changes in the electronic states of carbon were studied experimentally using surface-sensitive X-ray photoelectron spectroscopy and near-edge X-ray absorption fine structure (NEXAFS) spectroscopy. NEXAFS data in combination with density functional theory calculations revealed the dative interactions between lithium sp 2 hybridized states and carbon π*-type orbitals. Corrugated defective layers of graphene provide lithium with new bonding configurations, shorter distances, and stronger orbital overlapping, resulting in significant charge transfer between carbon and lithium. PC annealing heals defects, and as a result, the amount of lithium on the surface decreases. This conclusion was supported by electrochemical studies of as-grown and annealed PC in lithium-ion batteries. The former nanomaterial showed higher capacity values at all applied current densities. The results demonstrate that the lithium storage in carbon-based electrodes can be improved by introducing defects into the graphene layers., Competing Interests: The authors declare no conflict of interest.

The effect of humidity on the electrical conductivity of single-walled carbon nanotube (SWCNT) films depends on both the conductivity of individual nanotubes and the electrical contacts between them. Here, we study these factors by comparing the sensor response of nanotubes with fluorine- and nitrogen-containing groups attached to the sidewalls. Experiments carried out in a wide range of relative humidity (RH) at room and elevated temperatures showed that the conductivity of non-functionalized SWCNTs and contacts between them decreases upon the adsorption of water molecules. Covalent fluorination reduces the conductivity of SWCNTs and significantly increases the sensitivity of the film to low concentrations of water vapor. The response at high RH decreases due to the large number of water molecules adsorbed on the conductive regions of the nanotubes. As a result of substitutional reactions of fluorinated SWCNTs with dimethylformamide and ethylenediamine, nitrogen-containing groups are added, the amount of which, however, is much less than the amount of fluorine. This modification of the SWCNTs improves intertube contacts in the film and increases the surface area for water adsorption. Our results show that an increase in the number of functional groups on the SWCNT surface enhances the sensitivity of the sensor to low water concentrations and worsens the response at high RH. SWCNTs modified with ethylenediamine have the highest sensitivity over the entire range of RH.

Fluorinated graphitic layers with good mechanical and chemical stability, polar C-F bonds, and tunable bandgap are attractive for a variety of applications. In this work, we investigated the photolysis of fluorinated graphites with interlayer embedded acetonitrile, which is the simplest representative of the acetonitrile-containing photosensitizing family. The samples were continuously illuminated in situ with high-brightness non-monochromatized synchrotron radiation. Changes in the compositions of the samples were monitored using X-ray photoelectron spectroscopy and near-edge X-ray absorption fine structure (NEXAFS) spectroscopy. The NEXAFS N K-edge spectra showed that acetonitrile dissociates to form HCN and N 2 molecules after exposure to the white beam for 2 s, and the latter molecules completely disappear after exposure for 200 s. The original composition of fluorinated matrices CF 0.3 and CF 0.5 is changed to CF 0.10 and GF 0.17 , respectively. The highly fluorinated layers lose fluorine atoms together with carbon neighbors, creating atomic vacancies. The edges of vacancies are terminated with the nitrogen atoms and form pyridinic and pyrrolic units. Our in situ studies show that the photolysis products of acetonitrile depend on the photon irradiation duration and composition of the initial CF x matrix. The obtained results evaluate the radiation damage of the acetonitrile-intercalated fluorinated graphites and the opportunities to synthesize nitrogen-doped graphene materials.

Herein, ZIF-8 pre-grown on carbon cloth (CC) leads to preferential and homogenizing Zn deposition to accelerate Zn-ion diffusion. CC with uniform Zn deposits induced from ZIF-8 promotes rapid Zn plating, resulting in balanced kinetics between electrodes. The as-assembled ZICs show a high specific capacitance of 302 F g -1 at 0.5 A g -1 , an outstanding rate performance of 188 F g -1 at 20 A g -1 and 100% capacitance retention after 10000 cycles.

The interlayer space of 2D materials can be a slit reactor where transformations not typical for the gas phase occur. We report redox reactions involving acetonitrile and nitrogen oxide guests in galleries of fluorinated graphite. Fluorinated graphite intercalation compounds with acetonitrile are treated with dinitrogen tetraoxide and the synthesis products are studied by a set of experimental methods. Data analysis reveals that N2O4 dissociates in fluorinated graphite matrices to form nitrogen-containing species NO3, NO2, NO, and N2. The interaction of NO3 with acetonitrile yields HNO3, which predominates as a guest in the synthesis products independently of the fluorination degree of the matrix. This reaction is accompanied by the removal of fluorine atoms weakly bonded to the graphite layers, leading to partial defluorination of the matrices. Our work demonstrates the possibility of using fluorinated graphite as a test nanoreactor whose dimension can be controlled by fluorination of the layers.

Highly porous nitrogen-doped carbon nanomaterials have distinct advantages in energy storage and conversion technologies. In the present work, hydrothermal treatments in water or ammonia solution were used for modification of mesoporous nitrogen-doped graphitic carbon, synthesized by deposition of acetonitrile vapors on the pyrolysis products of calcium tartrate. Morphology, composition, and textural characteristics of the original and activated materials were studied by transmission electron microscopy, X-ray photoelectron spectroscopy, near-edge X-ray absorption fine structure spectroscopy, infrared spectroscopy, and nitrogen gas adsorption method. Both treatments resulted in a slight increase in specific surface area and volume of micropores and small mesopores due to the etching of carbon surface. Compared to the solely aqueous medium, activation with ammonia led to stronger destruction of the graphitic shells, the formation of larger micropores (1.4 nm vs 0.6 nm), a higher concentration of carbonyl groups, and the addition of nitrogen-containing groups. The tests of nitrogen-doped carbon materials as electrodes in 1M H 2 SO 4 electrolyte and sodium-ion batteries showed improvement of electrochemical performance after hydrothermal treatments especially when ammonia was used. The activation method developed in this work is hopeful to open up a new route of designing porous nitrogen-doped carbon materials for electrochemical applications., Competing Interests: The authors declare no conflict of interest. The funders had no role in the design of the study; in the collection, analyses, or interpretation of data; in the writing of the manuscript, or in the decision to publish the results.

Diamond films are advanced engineering materials for various industrial applications requiring a coating material with extremely high thermal conductivity and low electrical conductivity. An approach for the synthesis of diamond films via high-speed jet deposition of thermally activated gas has been applied. In this method, spatially separated high-speed flows of methane and hydrogen were thermally activated, and methyl and hydrogen radicals were deposited on heated molybdenum substrates. The morphology and structure of three diamond films were studied, which were synthesized at a heating power of 900, 1700, or 1800 W, methane flow rate of 10 or 30 sccm, hydrogen flow rate of 1500 or 3500 sccm, and duration of the synthesis from 1.5 to 3 h.The morphology and electronic state of the carbon on the surface and in the bulk of the obtained films were analyzed by scanning electron microscopy, Raman scattering, X-ray photoelectron, and near-edge X-ray absorption fine structure spectroscopies. The diamond micro-crystals with a thick oxidized amorphous sp 2 -carbon coating were grown at a heating power of 900 W and a hydrogen flow rate of 1500 sccm. The quality of the crystals was improved, and the growth rate of the diamond film was increased seven times when the heating power was 1700-1800 W and the methane and hydrogen flow rates were 30 and 3500 sccm, respectively. Defective octahedral diamond crystals of 30 μm in size with a thin sp 2 -carbon surface layer were synthesized on a Mo substrate heated at 1273 K for 1.5 h. When the synthesis duration was doubled, and the substrate temperature was decreased to 1073 K, the denser film with rhombic-dodecahedron diamond crystals was grown. In this case, the thinnest hydrogenated sp 2 -carbon coating was detected on the surface of the diamond crystals.

Investigation of carbon/lithium interfaces is of great importance for elaboration of energy storage devices. Here, the effect of vacuum thermal deposition of lithium on single-walled carbon nanotubes (SWCNTs) is investigated by in situ X-ray photoelectron spectroscopy (XPS) and near-edge X-ray absorption fine structure spectroscopy. From the XPS data, the composition of lithiated sample is LiC24. That corresponds to the presence of two types of carbon atoms on the SWCNT surface, namely, those located closely and far away from the adsorbed lithium. Quantum-chemical modeling of XPS valence-band spectra and calculation of atomic charges and molecular electrostatic potential map found that the former type of carbon atoms is in strong positive electric field created by lithium, whereas the Li-free SWCNT areas are charged negatively. An alternation of areas of positive potential and negative potential on the surface of partially lithiated SWCNTs can significantly affect processes in an electrochemical cell.

Single-walled carbon nanotubes (SWCNTs) possessing a confined inner space protected by chemically resistant shells are promising for delivery, storage, and desorption of various compounds, as well as carrying out specific reactions. Here, we show that SWCNTs interact with molten mercury dichloride (HgCl 2 ) and guide its transformation into dimercury dichloride (Hg 2 Cl 2 ) in the cavity. The chemical state of host SWCNTs remains almost unchanged except for a small p-doping from the guest Hg 2 Cl 2 nanocrystals. The density functional theory calculations reveal that the encapsulated HgCl 2 molecules become negatively charged and start interacting via chlorine bridges when local concentration increases. This reduces the bonding strength in HgCl 2 , which facilitates removal of chlorine, finally leading to formation of Hg 2 Cl 2 species. The present work demonstrates that SWCNTs not only serve as a template for growing nanocrystals but also behave as an electron-transfer catalyst in the spatially confined redox reaction by donation of electron density for temporary use by the guests.

Double-walled carbon nanotubes (DWCNTs) are fluorinated using (1) fluorine F 2 at 200 °C, (2) gaseous BrF 3 at room temperature, and (3) CF 4 radio-frequency plasma functionalization. These have been comparatively studied using transmission electron microscopy and infrared, Raman, X-ray photoelectron, and near-edge X-ray absorption fine structure (NEXAFS) spectroscopy. A formation of covalent C-F bonds and a considerable reduction in the intensity of radial breathing modes from the outer shells of DWCNTs are observed for all samples. Differences in the electronic state of fluorine and the C-F vibrations for three kinds of the fluorinated DWCNTs are attributed to distinct local surroundings of the attached fluorine atoms. Possible fluorine patterns realized through a certain fluorination technique are revealed from comparison of experimental NEXAFS F K-edge spectra with quantum-chemical calculations of various models. It is proposed that fluorination with F 2 and BrF 3 produces small fully fluorinated areas and short fluorinated chains, respectively, while the treatment with CF 4 plasma results in various attached species, including single or paired fluorine atoms and -CF 3 groups. The results demonstrate a possibility of different patterning of carbon surfaces through choosing the fluorination method.

Nitrogen-containing multi-wall carbon nanotubes (N-MWCNTs) were synthesized using aerosol assisted chemical vapor deposition (CVD) techniques in conjunction with benzylamine:ferrocene or acetonitrile:ferrocene mixtures. Different amounts of toluene were added to these mixtures in order to change the N/C ratio of the feedstock. X-ray photoelectron and near-edge X-ray absorption fine structure spectroscopy detected pyridinic, pyrrolic, graphitic, and molecular nitrogen forms in the N-MWCNT samples. Analysis of the spectral data indicated that whilst the nature of the nitrogen-containing precursor has little effect on the concentrations of the different forms of nitrogen in N-MWCNTs, the N/C ratio in the feedstock appeared to be the determining factor. When the N/C ratio was lower than ca. 0.01, all four forms existed in equal concentrations, for N/C ratios above 0.01, graphitic and molecular nitrogen were dominant. Furthermore, higher concentrations of pyridinic nitrogen in the outer shells and N2 molecules in the core of the as-produced N-MWCNTs suggest that the precursors were decomposed into individual atoms, which interacted with the catalyst surface to form CN and NH species or in fact diffused through the bulk of the catalyst particles. These findings are important for a better understanding of possible growth mechanisms for heteroatom-containing carbon nanotubes (CNTs) and therefore paving the way for controlling the spatial distribution of foreign elements in the CNTs using CVD processes.

Detonation nanodiamonds (NDs) were deposited on the surface of aligned carbon nanotubes (CNTs) by immersing a CNT array in an aqueous suspension of NDs in dimethylsulfoxide (DMSO). The structure and electronic state of the obtained CNT-ND hybrid material were studied using optical and electron microscopy and Infrared, Raman, X-ray photoelectron and near-edge X-ray absorption fine structure spectroscopy. A non-covalent interaction between NDs and CNT and preservation of vertical orientation of CNTs in the hybrid were revealed. We showed that current-voltage characteristics of the CNT-ND cathode are changed depending on the applied field; below ~3 V/µm they are similar to those of the initial CNT array and at the higher field they are close to the ND behavior. Involvement of the NDs in field emission process resulted in blue luminescence of the hybrid surface at an electric field higher than 3.5 V/µm. Photoluminescence measurements showed that the NDs emit blue-green light, while blue luminescence prevails in the CNT-ND hybrid. The quenching of green luminescence was attributed to a partial removal of oxygen-containing groups from the ND surface as the result of the hybrid synthesis.

Generally speaking, excellent electrochemical performance of metal oxide/graphene nanosheets (GNSs) composite is attributed to the interfacial interaction (or "synergistic effect") between constituents. However, there are no any direct observations on how the electronic structure is changed and how the properties of Li-ion storage are affected by adjusting the interfacial interaction, despite of limited investigations on the possible nature of binding between GNSs and metal oxide. In this paper, CuO nanosheets/GNSs composites with a little Cu2O (ca. 4 wt %) were utilized as an interesting model to illustrate directly the changes of interfacial nature as well as its deep influence on the electronic structure and Li-ion storage performance of composite. The interfacial adjustment was successfully fulfilled by removal of Cu2O in the composite by NH3·H2O. Formation of Cu-O-C bonds on interfaces both between CuO and GNSs, and Cu2O and GNSs in the original CuO/GNSs composites was detected. The small interfacial alteration by removal of the little Cu2O results in the obvious changes in electronic structure, such as weakening of covalent Cu-O-C interfacial interaction and recovery of π bonds in graphene, and simultaneously leads to variations in electrochemical performance of composites, including a 21% increase of reversible capacity, degradation of cyclic stability and rate-performance, and obvious increase of charge-transfer resistance, which can be called a "butterfly effect" in graphene-based metal oxide composites. These interesting phenomena could be helpful to design not only the high-performance graphene/metal oxide anode materials but also various advanced graphene-based composites used in the other fields such as sensors, catalysis, fuel cells, solar cells, etc.

Effect of Ar(+) ion irradiation on the structure of pristine and fluorinated single-wall carbon nanotubes (SWCNTs) was examined using transmission electron microscopy (TEM), Raman, and x-ray photoelectron spectroscopy (XPS). The TEM analysis revealed retention of tubular structures in both irradiated samples while Raman spectroscopy and XPS data indicated a partial destruction of nanotubes and formation of oxygen-containing groups on the nanotube surface. From similarity of electronic states of carbon in the irradiated pristine and fluorinated SWCNTs observed by XPS, it was suggested that defluorination of nanotubes proceeded with breaking of C-F bonds.