Search

Introduction: The use of dual-task model such as dual-task gait has been extensively studied to assess cognitive-motor performance among older adults. However, space restriction and safety factor limit its applications in remote assessment. To address the gap, we propose a video processing-based approach to remotely quantify cognitive-motor performance using a 20-second repetitive elbow flection-extension test with dual-task condition, called video-based motoric-cognitive meter (MCM). Methods: Eighteen older participants (age: 78.6±6.5 years) who were clinically diagnosed either as having mild cognitive impairment (MCI) or dementia were included in this study. Participants were asked to perform 20-second repetitive elbow flexion-extension exercise with a memory exercise by counting backward from a two-digit number. During the test, all movements of the forearm were recorded by a video camera. As a comparator, a validated wrist-worn sensor was used, which allowed quantifying upper-extremity kinematics. Results: The results showed a good agreement (r ≥ 0.530 and ICC2,1 ≥ 0.681) between the derived dual-task upper-extremity motor performance from the proposed video-based MCM and a clinically validated sensor-based MCM. We also observed moderate correlations (|r| ≥ 0.496) between some measures of video-based MCM (flexion time, extension time, and flexion-extension time) and clinical cognitive scale (Minimum Mental State Examination, abbreviation: MMSE). Additionally, some measures of dual-task upper-extremity motor performance (speed, flexion time, extension time, and flexion-extension time) were associated with dual-task gait speed (|r| ≥ 0.557), which has been found to be correlated with cognitive impairment. Lastly, the selected dual-task motor performance metric (flexion time) was sensitive to predict MMSE scores in linear regression analyses with statistical significance (adjusted R2 = 0.306, p = 0.025). Conclusion: This study proposes a video processing-based approach to analyze dual-task upper-extremity motor performance from a simple and convenient upper-extremity function test. The results indicate concurrent validity of the proposed video-based MCM compared with the sensor-based MCM, and associations between dual-task upper-extremity motor performance and clinically validated cognitive markers (MMSE scores and dual-task gait). Future studies are warranted to explore sensitivity of this solution to promote remote assessment of cognitive-motor performance among older adults in telehealth applications.

Improved life expectancy is increasing the number of older adults who suffer from motor-cognitive decline. Unfortunately, conventional balance exercise programs are not tailored to patients with cognitive impairments, and exercise adherence is often poor due to unsupervised settings. This study describes the acceptability and feasibility of a sensor-based in-home interactive exercise system, called tele-Exergame, used by older adults with mild cognitive impairment (MCI) or dementia. Our tele-Exergame is specifically designed to improve balance and cognition during distractive conditioning while a telemedicine interface remotely supervises the exercise, and its exercises are gamified balance tasks with explicit augmented visual feedback. Fourteen adults with MCI or dementia (Age = 68.1 ± 5.4 years, 12 females) participated and completed exergame twice weekly for six weeks at their homes. Before and after 6 weeks, participants’ acceptance was assessed by Technology Acceptance Model (TAM) questionnaire, and participants’ cognition and anxiety level were evaluated by the Montreal Cognitive Assessment (MoCA) and Beck Anxiety Inventory (BAI), respectively. Results support acceptability, perceived benefits, and positive attitudes toward the use of the system. The findings of this study support the feasibility, acceptability, and potential benefit of tele-Exergame to preserve cognitive function among older adults with MCI and dementia.

To explore the use of wearable sensors for objective measurement of motor impairment in spinocerebellar ataxia (SCA) patients during clinical assessments of gait and balance. In total, 14 patients with genetically confirmed SCA (mean age 61.6 ± 8.6 years) and 4 healthy controls (mean age 49.0 ± 16.4 years) were recruited through the Massachusetts General Hospital (MGH) Ataxia Center. Participants donned seven inertial sensors while performing two independent trials of gait and balance assessments from the Scale for the Assessment and Rating of Ataxia (SARA) and Brief Ataxia Rating Scale (BARS2). Univariate analysis was used to identify sensor-derived metrics from wearable sensors that discriminate motor function between the SCA and control groups. Multivariate linear regression models were used to estimate the subjective in-person SARA/BARS2 ratings. Spearman correlation coefficients were used to evaluate the performance of the model. Stride length variability, stride duration, cadence, stance phase, pelvis sway, and turn duration were different between SCA and controls (p

Introduction: Concern about falling is a prevalent worry among community-dwelling older adults and may contribute to a decline in physical and mental health. This study aimed to examine the association between mobility performance and concern about falling. Methods: Older adults aged 65 years and older, with Mini-Mental State Examination score ≥24, and ambulatory (with or without the assistive device) were included. Concern about falling was evaluated with Falls Efficacy Scale-International (FES-I) scores. Participants with high concern about falling were identified using the cutoff of FES-I ≥23. Participants’ motor capacity was assessed in standardized walking tests under single- and dual-task conditions. Participants’ mobility performance was measured based on a 48-h trunk accelerometry signal from a wearable pendant sensor. Results: No significant differences were observed at participant characteristics across groups with different levels of concern about falling (low: N = 64, age = 76.3 ± 7.2 years, female = 46%; high: N = 59, age = 79.3 ± 9.1 years, female = 47%), after propensity matching with BMI, age, depression, and cognition. With adjustment of motor capacity (stride velocity and stride length under single- and dual-task walking conditions), participants with high concern about falling had significantly poorer mobility performance than those with low concern about falling, including lower walking quantity (walking bouts, steps and time per day, and walking bout average, walking bout variability, and longest walking bout, p ≤ 0.013), and poorer daily-life gait (stride velocity and gait variability, p ≤ 0.023), and poorer walking quality (frontal gait symmetry, and trunk acceleration and velocity intensity, p ≤ 0.041). The selected mobility performance metrics (daily steps and frontal gait symmetry) could significantly contribute to identifying older adults with high concern about falling (p ≤ 0.042), having better model performance (p = 0.036) than only walking quantity (daily steps) with adjustment of confounding effects from the motor capacity (stride length under dual-task walking condition). Conclusion: There is an association between mobility performance and concern about falling in older adults. Mobility performance metrics can serve as predictors to identify older adults with high concern about falling, potentially providing digital biomarkers for clinicians to remotely track older adults’ change of concern about falling via applications of remote patient monitoring.

Sandwich core materials that offer superior mechanical properties at minimum weight are essential in designing high-performance sandwich structures. Hierarchical materials are ideal templates for this purpose. In this paper, we investigate the mechanical performance of a pyramidal–pyramidal hierarchical lattice material to highlight its potential as the core material for sandwich structures. Three-dimensional failure mechanism maps for the pyramidal–pyramidal hierarchical lattice material are developed under different loading conditions and the results are compared to finite element simulations. Next, we study the mechanical response and failure modes of a sandwich panel with self-similar pyramidal lattice core construction subjected to in-plane compression and three-point bending. The current study indicates that the pyramidal–pyramidal hierarchical configuration can improve the load bearing capacity and core buckling resistance of the sandwich structures at low density. The study provides insights into the role of structural hierarchy in tuning the mechanical response of the lattice materials and expands the application envelope of lightweight sandwich structures by effectively increasing the structural buckling resistance.

Biomimetic scales provide a convenient template to tailor the bending stiffness of the underlying slender substrate due to their mutual sliding after engagement. Scale stiffness can therefore directly impact the substrate behavior, opening a potential avenue for substrate stiffness tunability. Here, we have developed a biomimetic beam, which is covered by tunable stiffness scales. Scale tunability is achieved by specially designed plate like scales consisting of layers of low melting point alloy (LMPA) phase change materials fully enclosed inside a soft polymer. These composite scales can transition between stiff and soft states by straddling the temperatures across LMPA melting points thereby drastically altering stiffness. We experimentally analyze the bending behavior of biomimetic beams covered with tunable stiffness scales of two architectures—one with single enclosure of LMPA and one with two enclosures of different melting point LMPAs. These architectures provide a continuous stiffness change of the underlying substrate post engagement, controlled by the operating temperature. We characterize this response using three-point bending experiments at various temperature profiles. Our results demonstrate for the first time, the pronounced and reversible tunability in the bending behavior of biomimetic scale covered beam, which are strongly dependent on the scale material and architecture. Particularly, it is shown that the bending stiffness of the biomimetic scale covered beam can be actively and reversibly tuned by a factor of up to 7. The developed biomimetic beam has applications in soft robotic grippers, smart segmented armors, deployable structures and soft swimming robots.

This paper presents a robotic gripper design that can perform customizable grasping tasks at the millimeter scale. The design is based on the origami string, a mechanism with a single degree of freedom that can be mechanically programmed to approximate arbitrary paths in space. By using this concept, we create miniature fingers that bend at multiple joints with a single actuator input. The shape and stiffness of these fingers can be varied to fit different grasping tasks by changing the crease pattern of the string. We show that the experimental behavior of these strings follows their analytical models and that they can perform a variety of tasks including pinching, wrapping, and twisting common objects such as pencils, bottle caps, and blueberries.

Well-designed honeycomb sandwich panels are known to have superior blast performance compared to their corresponding solid panel of the same mass. However, the residual structural capacity of honeycomb sandwich panels and their blast resilience has not been systematically studied. Here, we investigate the structural behavior of all-metal honeycomb sandwich panels after shock loading using detailed numerical simulations. The initial shock is varied from relatively small intensities to moderate intensities sufficient to create material failure and significant plastic deformation in the panel. The structural response of the shock-loaded panels is investigated under quasi-static punch indentation and in-plane compression. The maximum load carrying and energy absorption capacities of shock-loaded panels are quantified for a wide range of initial shock intensities and different panel core densities. Failure maps for the honeycomb panels were constructed for each quasi-static loading condition by considering three failure modes: core failure, face sheet failure, and total panel detachment from its support. This study provides new insights into the behavior and structural resilience of the shock-loaded sandwich panels, while further highlighting their potential in the development of resilient structural systems.

Displacement and stress fields in a functionally graded (FG) fiber-reinforced rotating annular disk with a non-uniform thickness profile, subjected to angular deceleration and a temperature profile were investigated. Unidirectional fibers were considered to be circumferentially distributed within the disk with fiber volume fraction changing radially. The governing equations for displacement, stress, and temperature fields were solved using finite difference method. The results indicated that thermal induced stresses were more dominate than the rotational induced stresses. Disks which were fiber rich at the inner radius, the fibers made negligible difference on the displacement and stress fields when compared to a homogenous disk made from the matrix material. In addition, it was found that the deceleration magnitude had no effect on the radial and hoop stresses, nor the temperature on the developed shear stress. The shear stress was only affected by the disk deceleration. Tsai-Wu failure criterion was applied for decelerating disks to ascertain their failure behavior. The results show that Tsai-Wu failure index is dominated by the thermal stresses.

Background Bone healing process includes four phases: inflammatory response, soft callus formation, hard callus development, and remodeling. Mechanobiological models have been used to investigate the role of various mechanical and biological factors on bone healing. However, the effects of initial healing phase, which includes the inflammatory stage, the granulation tissue formation, and the initial callus formation during the first few days post-fracture, are generally neglected in such studies. Methods In this study, we developed a finite-element-based model to simulate different levels of diffusion coefficient for mesenchymal stem cell (MSC) migration, Young’s modulus of granulation tissue, callus thickness and interfragmentary gap size to understand the modulatory effects of these initial phase parameters on bone healing. Results The results quantified how faster MSC migration, stiffer granulation tissue, thicker callus, and smaller interfragmentary gap enhanced healing to some extent. However, after a certain threshold, a state of saturation was reached for MSC migration rate, granulation tissue stiffness, and callus thickness. Therefore, a parametric study was performed to verify that the callus formed at the initial phase, in agreement with experimental observations, has an ideal range of geometry and material properties to have the most efficient healing time. Conclusions Findings from this paper quantified the effects of the initial healing phase on healing outcome to better understand the biological and mechanobiological mechanisms and their utilization in the design and optimization of treatment strategies. It is also demonstrated through a simulation that for fractures, where bone segments are in close proximity, callus development is not required. This finding is consistent with the concepts of primary and secondary bone healing.

We constructed a new class of three-dimensional cellular metamaterials by connecting planar structure with anti-chiral topology. This was achieved by introducing a unique node design for connecting planar materials to enable constructing a three-dimensional architecture. This node design is based on linking the circular elements of the anti-chiral topology using oblique load-bearing ligaments. As the planar structure is subjected to loading, the circular elements rotate and the ligaments undergo bending, resulting in out-of-plane deformation of the three-dimensional cellular metamaterials. The node design, and specifically the ligaments' revolution angle govern the behavior of cellular metamaterials. This was demonstrated by designing cellular metamaterials with a wide range of positive and negative Poisson's ratio in the out-of-plane direction. Keywords: Cellular material, Auxetic behavior, Poisson's ratio, Chirality

Mechanical properties and failure mechanisms of sandwich panels with “corrugated-pyramidal” hierarchical lattice cores were investigated through analytical modeling and detailed numerical simulations. This included studying the behavior of hierarchical lattice core material under compression and shearing, as well as investigating the mechanical performance of sandwich panels subjected to in-plane compression and three-point bending. Failure maps were constructed for the hierarchical lattice cores, as well as sandwich panels with hierarchical lattice cores by deriving analytical closed-form expressions for strength for all possible failure modes under each loading. 3D printed samples were manufactured and tested under out-of-plane compression in order to provide limited experimental validation of the study. Our study provides insights into the role of structural hierarchy in tuning the mechanical behavior of sandwich structures, and new opportunities for designing ultra-lightweight lattice cores with optimal performance.

The venous morphology of a typical plant leaf affects its mechanical and thermal properties. Such a material could be considered as a fiber reinforced composite structure where the veins and the rest of the leaf are considered as two materials having highly contrast mechanical and thermal properties. The variegated venations found in nature is idealized into three principal fibers—the central mid-fiber corresponding to the mid-rib, straight parallel secondary fibers attached to the mid-fiber representing the secondary veins, and then another set of parallel fibers emanating from the secondary fibers mimicking the tertiary veins of a typical leaf. This paper addresses the in-plane thermal conductivity of such a composite by considering such a venous fiber morphology embedded in a matrix material. We have considered two cases, fibers having either higher or lower conductivity respect to the matrix. The tertiary fibers do not interconnect the secondary fibers in our present study. We carry out finite element based computational investigation of the thermal conductivity of these composites under uniaxial thermal gradients and study the effect of different fiber architectures. To this end, we use two broad types of architectures both having similar central main fiber but differing in either having only secondary fibers or additional tertiary fibers. The fiber and matrix volume fractions are kept constant and a comparative parametric study is carried out by varying the inclination of the secondary fibers. We find the heat conductivity in the direction of the main fiber (Y direction) increases significantly as the fiber angle of the secondary increases. Furthermore, for composite with metal fibers, the conductivity in the Y direction is further enhanced when composite is manufactured by having secondary fibers forming a closed cell structure. However, for composite with ceramic fibers, the conductivity of the composite in the Y direction is little affected by having secondary fibers closed. An opposite behavior is observed when considering conductivity of the composite in the X direction. The conductivity of the composite in the X direction is reduced with increase in the angle of the secondary fibers. Higher conductivity in the X direction is achieved for composite with no closed cells for composites with metal fibers. The results also indicate that for composites with the constant fiber volume fraction, morphology of tertiary fibers may not significantly alter material conductivities. In conclusion, introducing a leaf-mimicking topology in fiber architecture can provide significant additional degrees of tunability in design of these composite structures.

Bone fracture is a very common body injury. The healing process is physiologically complex, involving both biological and mechanical aspects. Following a fracture, cell migration, cell/tissue differentiation, tissue synthesis, and cytokine and growth factor release occur, regulated by the mechanical environment. Over the past decade, bone healing simulation and modeling has been employed to understand its details and mechanisms, to investigate specific clinical questions, and to design healing strategies. The goal of this effort is to review the history and the most recent work in bone healing simulations with an emphasis on both biological and mechanical properties. Therefore, we provide a brief review of the biology of bone fracture repair, followed by an outline of the key growth factors and mechanical factors influencing it. We then compare different methodologies of bone healing simulation, including conceptual modeling (qualitative modeling of bone healing to understand the general mechanisms), biological modeling (considering only the biological factors and processes), and mechanobiological modeling (considering both biological aspects and mechanical environment). Finally we evaluate different components and clinical applications of bone healing simulation such as mechanical stimuli, phases of bone healing, and angiogenesis., Highlights • Bone fracture healing is a series of biological processes, regulated by the mechanical environment and biological factors. • Conceptual models of bone fracture healing aim to understand the qualitative process and to formulate its general mechanism. • Mechanobiological models consider the effects of both mechanical environment and biological factors. • Mechanobiological regulations and mechanical stimuli effects on growth factors can potentially have clinical applications. • While important, the inflammatory phase in the bone healing process is not included in mechanobiological simulations.

A typical plant leaf can be idealized as a composite having three principal fibers: the central mid-fiber corresponding to the mid-rib, straight parallel secondary fibers attached to the mid-fiber representing the secondary veins, and then another set of parallel fibers emanating from the secondary fibers mimicking the tertiary fibers embedded in a matrix material. This paper introduces a biomimetic composite design inspired by the morphology of venous leafs and investigates the effects of venation morphologies on the in-plane mechanical properties of the biomimetic composites using finite element method. The mechanical properties such as Young’s moduli, Poisson’s ratio, and yield stress under uniaxial loading of the resultant composite structures was studied and the effect of different fiber architectures on these properties was investigated. To this end, two broad types of architectures were used both having similar central main fiber but differing in either having only secondary fibers or additional tertiary fibers. The fiber and matrix volume fractions were kept constant and a comparative parametric study was carried out by varying the inclination of the secondary fibers. The results show that the elastic modulus of composite in the direction of main fiber increases linearly with increasing the angle of the secondary fibers. Furthermore, the elastic modulus is enhanced if the secondary fibers are closed, which mimics composites with closed cellular fibers. In contrast, the elastic modulus of composites normal to the main fiber ( x direction) exponentially decreases with the increase of the angle of the secondary fibers and it is little affected by having secondary fibers closed. Similar results were obtained for the yield stress of the composites. The results also indicate that Poisson’s ratio linearly increases with the secondary fiber angle. The results also show that for a constant fiber volume fraction, addition of various tertiary fibers may not significantly enhance the mechanical properties of the composites. The mechanical properties of the composites are mainly dominated by the secondary fibers. Finally, a simple model was proposed to predict these behaviors.

Conventional single-lap adhesive joints between identical adherends achieve ultimate strength only after significant inelastic deformation of the adhesive and perhaps also the adherends. However purely elastic analysis provides insights and is relevant to fatigue initiation or brittle failure. We extend classical beam-based elastic results, both ‘within the bond’ (deriving more-accurate peak peel stress from the joint-edge moment) and ‘beyond the bond’ (determining the edge moment from adherend dimensions, remote boundary conditions, and load). Within the bond, we show that peak adhesive equivalent stress and principal stress are minimized when the bond length exceeds four characteristic lengths of the elastic-foundation shear stress equation. This makes simplified ‘long’ joint formulas attractive for initial design. We then examine how well the long-joint predicted peak peel stress matches plane strain finite element analysis, and empirically capture a peel-stress end effect due to nonzero adhesive Poisson ratio. With this end-effect correction, the limit of useful accuracy can be expressed as a ratio R a of (adherend axial stiffness) to (adhesive axial stiffness) being > a number of order 10 2 - 10 3 depending on Poisson ratio. This limit supplements the Goland and Reissner proposed applicability limit for elastic foundation analysis, expressed as a limiting ratio R v of through-thickness or vertical stiffnesses. Outside the bond, Timoshenko-style beam-column expressions are used to derive a simplified joint-edge moment factor. While similar in spirit to the edge-moment determination of Goland and Reissner for infinite-length pinned adherends, treating the bond region as a rigid block leads to simpler nonlinear expressions, and captures the moment-reducing benefits of shorter (finite-length) adherends and fixed-slope end conditions. Joint rotation effects become dominant when T L 2 > E I ( L is adherend free length, T is tensile load), then joint rotation magnitude depends on T D 2 / E I ( D is lap length).

In this paper, we present a method for multi-material topology optimization of lattice structures for maximum bulk modulus. Unlike ground structure approaches that employ 1-d finite elements such as bars and beams to design periodic lattices, we employ a 3-d representation where each lattice bar is described as a cylinder. To accommodate the 3-d bars, we employ the geometry projection method, whereby a high-level parametric description of the bars is smoothly mapped onto a density field over a fixed analysis grid. In addition to the geometric parameters, we assign a size variable per material to each bar. By imposing suitable constraints in the optimization, we ensure that each bar is either made exclusively of one of a set of a multiple available materials or completely removed from the design. These optimization constraints, together with the material interpolation used in our formulation, make it easy to consider any number of available materials. Another advantage of our method over ground structure approaches with 1-d elements is that the bars in our method need not be connected at all times (i.e., they can ‘float’ within the design region), which makes it easier to find good designs with relatively few design variables. We illustrate the effectiveness of our method with numerical examples of bulk modulus maximization for two-material lattices with orthotropic symmetry, and for two- and three-material lattices with cubic symmetry.

Structural response and failure modes of honeycomb sandwich panels subjected to a shock (impulsive pressure) followed by a high velocity projectile impact were investigated using detailed finite element simulations. Performance of sandwich panels was quantified by maximum transverse deflection of the bottom face sheet and core crushing strain along with an investigation of their optimal behavior. Three failure modes were observed in panels - core failure, top face failure, and tearing and detachment from support. Failure maps of honeycomb sandwich panels were constructed to show the failure mode of panels as a function of shock intensity, projectile velocity and panel core relative density. In addition, a limited set of simulations were carried out to study the role of incident angle of projectile on the overall performance of a panel. These simulations showed that maximum deflection occurred for vertically impacting projectiles. However, we found that this did not directly translate to maximum core crushing strain in sandwich panels. The results provide new insight into the performance and failure of sandwich panels under complex dynamic loading conditions, and further highlight the potential of these panels for development of threat-resistant structural systems. 2016 Elsevier Ltd. All rights reserved. This work has been supported by the Qatar National Research Fund (QNRF) under Award Number NPRP 5-1298-2-560 . The views and conclusions contained in this document are those of the authors and should not be interpreted as necessarily representing the official policies, either expressed or implied, of the Qatar National Research Fund. Scopus

The effect of different surfactants on the removal efficiency of wiping surfaces contaminated with single walled carbon nanohorns (SWCNHs) was studied. To this end, sodium dodecylbenzenesulfonate (SDBS) and sodium dodecyl sulfate (SDS) surfactants were used, and their removal efficiencies with water only and with cleaning with a dry wipe were compared. The surfactant concentrations and wipe pressure during the wiping process were varied, and significant effects on removal efficiency were found. In addition, the results were compared with those obtained with single-walled carbon nanotubes (SWCNTs) and multi-walled CNTs (MWCNTs) and the differences among these nanostructures were reported. The results suggest that SDS and SDBS are good candidates for removal of SWCNHs deposited on silicon wafers with SDS removal efficiencies capable of exceeding 90%. In addition, the results show that there is an optimum wiping pressure and surfactant concentration with the highest removal efficiency. A direct relationship was also found between wipe saturation and removal efficiency of SWCNHs deposited on silicon substrates. The differences between individual nano structures were perceptible in spite of following similar broad trends; for instance, SWCNH contaminated surfaces in general proved more difficult to clean than surfaces contaminated with the other nanostructures.

Out of plane vibration of rotating disks limits their performances especially at certain critical speed. The critical speed of these disks may be affected by the presence of defects such as a circumferential crack. In this paper out of plane vibration of functionally graded (FG) rotating annular disks with a circumferential open crack is investigated. The cracked disk is modeled as two sub-disks, connected at the crack location by translational and rotational line springs, simulating the crack plate response to induced shear force and bending moment at the crack radius. These spring stiffness constants are obtained numerically using the finite element method (FEM) as a function of crack depth and radius. The rotational spring stiffness strongly depends on the disk rotation speed, while the stiffness of the translational spring is found to be independent of the disk speed. Both spring constants depend on the spatial distribution of the disk elastic modulus. The in-plane disk stresses are obtained using a semi-analytical approach. Those in plane stresses are used to obtain the governing equation of out of plane motion of the disk. A finite difference scheme is used to solve the partial differential equation of motion to obtain eigenvalues, critical speed and associated mode shapes. The lowest critical speed, which is one of the important parameters limiting the performance of the rotating disk, is obtained from the Campbell Diagram. It is found that irrespective of the distribution of the modulus of elasticity in the FG disk, increasing the crack depth or decreasing the crack radial distance from the disk center decreases the critical speed. The critical speed reduction is more pronounced for the case when the disk material modulus of elasticity is decreasing from the disk center. 2016 Elsevier Ltd. All rights reserved. This work has been supported by the Qatar National Research Foundation (QNRF) under Award no. NPRP 5-068-2-024 . Scopus

Carbon fiber reinforced three dimensional egg and pyramidal honeycomb grids cores with interconnected void spaces were fabricated using an interlocking method. The out-of-plane compression properties, failure modes, and energy absorption capacity of all-composite sandwich panels made of the new 3D grid cores were investigated. The analytical models for predicting the compressive stiffness and strength of both egg and pyramidal honeycomb grids cores were derived. The results showed that the fabricated sandwich panels have higher specific energy absorbing abilities compared to lightweight square honeycombs of same density (10–100 Kg/m3). The new core design promises novel applications for lightweight multifunctional structures due to increased flow in the inner spaces of the core construction, embedding of electrical lines, enhanced heat transfer, fuel storage and higher energy absorption compared to traditional cores.

In this paper, a new microarchitectured material is introduced that consists of a large periodic lattice of small compliant unit cells (i.e.

This work presents a computational method for the design of architected truss lattice materials where each strut can be made of one of a set of available materials. We design the lattices to extremize effective properties. As customary in topology optimization, we design a periodic unit cell of the lattice and obtain the effective properties via numerical homogenization. Each bar is represented as a cylindrical offset surface of a medial axis parameterized by the positions of the endpoints of the medial axis. These parameters are smoothly mapped onto a continuous density field for the primal and sensitivity analysis via the geometry projection method. A size variable per material is ascribed to each bar and penalized as in density-based topology optimization to facilitate the entire removal of bars from the design. During the optimization, we allow bars to be made of a mixture of the available materials. However, to ensure each bar is either exclusively made of one material or removed altogether from the optimal design, we impose optimization constraints that ensure each size variable is 0 or 1, and that at most one material size variable is 1. The proposed material interpolation scheme readily accommodates any number of materials. To obtain lattices with desired material symmetries, we design only a reference region of the unit cell and reflect its geometry projection with respect to the appropriate planes of symmetry. Also, to ensure bars remain whole upon reflection inside the unit cell or with respect to the periodic boundaries, we impose a no-cut constraint on the bars. We demonstrate the efficacy of our method via numerical examples of bulk and shear moduli maximization and Poisson’s ratio minimization for two- and three-material lattices with cubic symmetry.

We present a new method for the simultaneous topology optimization and material selection of structures made by the union of discrete geometric components, where each component is made of one of multiple available materials. Our approach is based on the geometry projection method, whereby an analytical description of the geometric components is smoothly mapped onto a density field on a fixed analysis grid. In addition to the parameters that dictate the dimensions, position, and orientation of the component, a size variable per available material is ascribed to each component. A size variable value of unity indicates that the component is made of the corresponding material. Moreover, all size variables can be zero, signifying the component is entirely removed from the design. We penalize intermediate values of the size variables via an aggregate constraint in the optimization. We also introduce a mutual material exclusion constraint that ensures that at most one material has a unity size variable in each geometric component. In addition to these constraints, we propose a novel aggregation scheme to perform the union of geometric components with dissimilar materials. These ingredients facilitate treatment of the multi-material case. Our formulation can be readily extended to any number of materials. We demonstrate our method with several numerical examples.

Origami designs offer extreme reconfigurability due to hinge rotation and facet deformation. This can be exploited to make lightweight metamaterials with controlled deployability and tunable properties. Here, we create a family of origami-inspired cellular metamaterials which can be programmed to have various stability characteristics and mechanical responses in three independent orthogonal directions. The cellular metamaterials were constructed from their origami unit cell that can have one or two admissible closed-loop configurations. The presence of the second closed-loop configuration leads to the emergence of bi-stability in the cellular metamaterial. We show that the stability and reconfigurability of the origami unit cell, and thus the constructed cellular metamaterials, can be programmed by manipulating the characteristic angles inherited from the origami pattern. Two examples of such programmable metamaterial with bi-stability in out-of-plane direction and anisotropic multi-stability in orthogonal directions are presented. Our study provides a platform to design programmable three-dimensional metamaterials significantly broadening the application envelope of origami.

We describe a minimal realization of reversibly programmable matter in the form of a featureless smooth elastic plate that has the capacity to store information in a Braille-like format as a sequence of stable discrete dimples. Simple experiments with cylindrical and spherical shells show that we can control the number, location, and the temporal order of these dimples, which can be written and erased at will. Theoretical analysis of the governing equations in a specialized setting and numerical simulations of the complete equations allow us to characterize the phase diagram for the formation of these localized elastic states, elastic bits (e-bits), consistent with our observations. Given that the inherent bistability and hysteresis in these low-dimensional systems arise exclusively due to the geometrical-scale separation, independent of material properties or absolute scale, our results might serve as alternate approaches to small-scale mechanical memories.