Search

The flat-plate solar collector (FPSC) three-dimensional (3D) model was used to numerically evaluate the energy and economic estimates. A laminar flow with 500 ≤ Re ≤ 1900, an inlet temperature of 293 K, and a solar flux of 1000W/m² were assumed the operating conditions. Two mono nanofluids, CuO-DW and Cu-DW, were tested with different shapes (Spherical, Cylindrical, Platelets, and Blades) and different volume fractions. Additionally, hybrid nanocomposites from CuO@Cu/DW with different shapes (Spherical, Cylindrical, Platelets and Blades), different mixing ratios (60%+40%, 50%+50% and 40%+60%) and different volume fractions (1 volume%, 2 volume%, 3 volume% and 4 volume%) were compared with mono nanofluids. At 1 volume% and Re = 1900, CuO-Platelets demonstrated the highest pressure drop (33.312 Pa). CuO-Platelets achieved the higher thermal enhancement with (8.761%) at 1 vol.% and Re = 1900. CuO-Platelets reduced the size of the solar collector by 25.60%. Meanwhile, CuO@Cu-Spherical (40:60) needed a larger collector size with 16.69% at 4 vol.% and Re = 1900. CuO-Platelets with 967.61, CuO -- Cylindrical with 976.76, Cu Platelets with 983.84, and Cu-Cylindrical with 992.92 presented the lowest total cost. Meanwhile, the total cost of CuO -- Cu -- Platelets with 60:40, 50:50, and 40:60 was 994.82, 996.18, and 997.70, respectively. [ABSTRACT FROM AUTHOR]

Graphene has piqued the interest of many researchers due to its superior mechanical, thermal, and physiochemical properties. Graphene nanoplatelets with covalently functionalized surfaces (CF-GNPs) were employed in turbulent-heated pipes to undertake thermal and economic studies. CF-GNPs and distilled water were used to make the current nanofluids at various mass percentages, such as 0.025, 0.05, 0.075%, and 0.1 wt.%. In the range of 6,401 Re 11,907, the thermal system was heated up to 11,205 W/m2 under fully developed turbulent flow conditions. Field emission scanning electron microscopy (FE-SEM), zeta potential, nanoparticle sizer, and field emission transmission electron microscopy (FE-TEM) were used to examine the morphological features and characterise the particles. In addition, the current thermal system's economic performance was assessed to estimate its price-to-operate ratio. There was a 16.10% reduction in heat exchanger size for 0.025 weight percent, 0.05 weight percent, 0.075 weight percent, and 0.1 weight percent. In addition, the power needed for the base fluid was 422 W, which was then lowered to 354 W, 326 W, 315 W, and 298 W for 0.025 wt.%, 0.05 wt.%, 0.075 wt.%, and 0.1 wt.%, respectively. [ABSTRACT FROM AUTHOR]

For companies, notably in the realms of energy and power supply, the essential requirement for highly efficient thermal transport solutions has become a serious concern. Current research highlighted the use of metallic oxides and carbon-based nanofluids as heat transfer fluids. This work examined two carbon forms (PEG@GNPs & PEG@TGr) and two types of metallic oxides (Al2O3 & SiO2) in a square heated pipe in the mass fraction of 0.1 wt.%. Laboratory conditions were as follows: 6401 ≤ Re ≤ 11,907 and wall heat flux = 11,205 W/m2. The effective thermal–physical and heat transfer properties were assessed for fully developed turbulent fluid flow at 20–60 °C. The thermal and hydraulic performances of nanofluids were rated in terms of pumping power, performance index (PI), and performance evaluation criteria (PEC). The heat transfer coefficients of the nanofluids improved the most: PEG@GNPs = 44.4%, PEG@TGr = 41.2%, Al2O3 = 22.5%, and SiO2 = 24%. Meanwhile, the highest augmentation in the Nu of the nanofluids was as follows: PEG@GNPs = 35%, PEG@TGr = 30.1%, Al2O3 = 20.6%, and SiO2 = 21.9%. The pressure loss and friction factor increased the highest, by 20.8–23.7% and 3.57–3.85%, respectively. In the end, the general performance of nanofluids has shown that they would be a good alternative to the traditional working fluids in heat transfer requests. [ABSTRACT FROM AUTHOR]

Covalent-functionalized graphene nanoplatelets (CF-GNPs) inside a circular heated-pipe and the subsequent pressure decrease loss within a fully developed turbulent flow were discussed in this research. Four samples of nanofluids were prepared and investigated in the ranges of 0.025 wt.%, 0.05 wt.%, 0.075 wt.%, and 0.1 wt.%. Different tools such as field emission scanning electron microscopy (FE-SEM), ultraviolet-visible-spectrophotometer (UV-visible), energy-dispersive X-ray spectroscopy (EDX), zeta potential, and nanoparticle sizing were used for the data preparation. The thermophysical properties of the working fluids were experimentally determined using the testing conditions established via computational fluid dynamic (CFD) simulations that had been designed to solve governing equations involving distilled water (DW) and nanofluidic flows. The average error between the numerical solution and the Blasius formula was ~4.85%. Relative to the DW, the pressure dropped by 27.80% for 0.025 wt.%, 35.69% for 0.05 wt.%, 41.61% for 0.075 wt.%, and 47.04% for 0.1 wt.%. Meanwhile, the pumping power increased by 3.8% for 0.025 wt.%, 5.3% for 0.05 wt.%, 6.6% for 0.075%, and 7.8% for 0.1 wt.%. The research findings on the cost analysis demonstrated that the daily electric costs were USD 214, 350, 416, 482, and 558 for DW of 0.025 wt.%, 0.05 wt.%, 0.075 wt.%, and 0.1 wt.%, respectively. [ABSTRACT FROM AUTHOR]

Numerical studies were performed to estimate the heat transfer and hydrodynamic properties of a forced convection turbulent flow using three-dimensional horizontal concentric annuli. This paper applied the standard k–ε turbulence model for the flow range 1 × 104 ≤ Re ≥ 24 × 103. A wide range of parameters like different nanomaterials (Al2O3, CuO, SiO2 and ZnO), different particle nanoshapes (spherical, cylindrical, blades, platelets and bricks), different heat flux ratio (HFR) (0, 0.5, 1 and 2) and different aspect ratios (AR) (1.5, 2, 2.5 and 3) were examined. Also, the effect of inner cylinder rotation was discussed. An experiment was conducted out using a field-emission scanning electron microscope (FE-SEM) to characterize metallic oxides in spherical morphologies. Nano-platelet particles showed the best enhancements in heat transfer properties, followed by nano-cylinders, nano-bricks, nano-blades, and nano-spheres. The maximum heat transfer enhancement was found in SiO2, followed by ZnO, CuO, and Al2O3, in that order. Meanwhile, the effect of the HFR parameter was insignificant. At Re = 24,000, the inner wall rotation enhanced the heat transfer about 47.94%, 43.03%, 42.06% and 39.79% for SiO2, ZnO, CuO and Al2O3, respectively. Moreover, the AR of 2.5 presented the higher heat transfer improvement followed by 3, 2, and 1.5. [ABSTRACT FROM AUTHOR]