Search

We have measured the spin torques of beta-Tantalum / Co20Fe60B20 bilayers versus Ta thickness at room temperature using an FMR technique. The spin Hall coefficient was calculated both from the observed change in damping coefficient of the ferromagnet with Ta thickness, and from the ratio of the symmetric and anti-symmetric components of the FMR signal. Results from these two methods yielded values for the spin Hall coefficient of -0.090+/-0.005 and -0.11+/-0.01, respectively. We have also identified a significant out-of-plane spin torque originating from Ta, which is constant with Ta thickness. We ascribe this to an interface spin orbit coupling, or Rashba effect, due to the strength and constancy of the torque with Ta thickness. From fitting measured data to a model including interface spin orbit coupling, we have determined the spin diffusion length for beta-Tantalum to be ~2.5 nm., Comment: 18 pages, 10 figures, 1 table, submitted to Science

UNKNOWN

This paper presents a technology development initiative focused on delivering SmallSats to orbit a variety of bodies using aerocapture. Aerocapture uses the drag of a single pass through the atmosphere to capture into orbit instead of relying on large quantities of rocket fuel. Using drag modulation flight control, an aerocapture vehicle adjusts its drag area during atmospheric flight through a single-stage jettison of a drag skirt, allowing it to target a particular science orbit in the presence of atmospheric uncertainties. A team from JPL, NASA Ames, and CU Boulder has worked to address the key challenges and determine the feasibility of an aerocapture system for SmallSats less than 180kg. Key challenges include the ability to accurately target an orbit, stability through atmospheric flight and the jettison event, and aerothermal stresses due to high heat rates.

Aerocapture has been extensively studied and these studies have shown the benefit for planetary exploration missions. While the traditional approach to aerocapture with lifting configurations and lift-guided modulations have been assessed to be technologically feasible, aerocapture using purely drag modulation was proposed and studied by Prof. Braun and his students. These studies show that if one can assess the feasibility of aerocapture using drag modulation at Venus, and develop tall pole technologies needed at Venus, then this concept is much easier to execute at all other relevant destinations. Based on the above finding, partnered proposals were submitted by Adam Nelessen at JPL and Ethiraj Venkatapathy at Ames in collaboration with Prof. Braun at the University of Colorado, Boulder (UCB). Under this partnership, Ames Research Center (ARC) is working to address some of the key entry technology challenges associated with drag modulation aerocapture at Venus. Drag modulation aerocapture is a simple, scalable, and likely cost-effective way to enhance planetary science missions. The approach envisioned is to design a small spacecraft, that would most likely be a secondary payload, with a removable drag skirt. The vehicle would enter the atmosphere at Venus with a low ballistic coefficient, decelerate rapidly, drop the skirt resulting in a smaller vehicle with a higher ballistic coefficient which would skip out of the atmosphere and enter into a desired orbit. ARC's role in this collaboration is multifold. First of which is to perform design studies on various pre- and post-jettison geometries utilizing a 3-DOF trajectory code to determine the aerodynamics and aerothermodynamics of the vehicles and evaluate viable thermal protection material system designs. Once these design studies are complete, Ames will then perform higher fidelity CFD and TPS sizing to further design the vehicles. Second, the multi-body separation dynamics of the drag modulation event will be explored using both CFD simulations (CART3-D and US3D) as well as possible ballistic range testing. ARC's tools and expertise have been used to assess and advise on the selection of the separating configuration. In addition to the preliminary evaluation, ARC will provide tools and expertise to UCB team members to further assess aerodynamic interactions between the separating bodies and provide guidance as to the feasibility of stable transition.

Dragonfly is a proposed spacecraft and mission that would send a mobile robotic rotorcraft lander to Titan, the largest moon of Saturn, in order to study prebiotic chemistry and extraterrestrial habitability at various locations. Titan is unique in having an abundant, complex, and diverse carbon-rich chemistry on the surface of a water-ice-dominated world with an interior water ocean, making it a high priority target for astrobiology and origin of life studies. The mission was initially proposed in April 2017 to NASA's New Frontiers program by the Johns Hopkins Applied Physics Laboratory. In December 2017, it was selected as one of two finalists (out of twelve proposals) to further refine the mission's concept. NASA Ames Research Center and NASA Langley Research Center are partnering as the leads for the Dragonfly's entry system to provide the completed EDL Assembly. The aerothermal analysis for Dragonfly utilizes four simulation tools from NASA Ames Research Center. Traj for calculating the trajectory, DPLR 4.04.0 for calculating the flowfield around the vehicle and convective heating, NEQAIR V15.0 for calculating the radiative heating, and FIAT for calculating the material response and thermal protection system (TPS) sizing for the heatshield. The entry conditions are relatively benign and can readily be accommodated with a tiled PICA heatshield similar to MSL and a number of flight proven materials for the backshell. This work will demonstrate that the aerothermal entry environments can be readily solved using heritage materials and techniques.

UNKNOWN

Estimate the mass of the Thermal Protection System (TPS) for a single design construct of an atmospheric entry probe with a rigid aeroshell, which could be used at five destinations, i.e. Venus, Saturn, Uranus, Neptune, and perhaps, Jupiter. The entry mass of the probe is 400 kg with a ballistic coefficient of 216 kg/m2. Process: The 3DoF trajectory simulation program Traj, coupled with the TPS response program FIAT was used for simulation and design. The assumed atmospheric models were VIRA (Venus-GRAM) for Venus, the Julianne Moses' model for Saturn, a NASA Ames engineering model for Uranus, Neptune-GRAM for Neptune, and Galileo Probe (Al Seiff's) result for Jupiter.