Search

The present development of non-wafer-based photovoltaics (PV) allows supporting thin film solar cells on a wide variety of low-cost recyclable and flexible substrates such as paper, thereby extending PV to a broad range of consumer-oriented disposable applications where autonomous energy harvesting is a bottleneck issue. However, their fibrous structure makes it challenging to fabricate good-performing inorganic PV devices on such substrates. The advances presented here demonstrate the viability of fabricating thin film silicon PV cells on paper coated with a hydrophilic mesoporous layer. Such layer can not only withstand the cells production temperature (150 °C), but also provide adequate paper sealing and surface finishing for the cell's layers deposition. The substances released from the paper substrate are continuously monitored during the cell deposition by mass spectrometry, which allows adapting the procedures to mitigate any contamination from the substrate. In this way, a proof-of-concept solar cell with 3.4% cell efficiency (41% fill factor, 0.82 V open-circuit voltage and 10.2 mA cm−2 short-circuit current density) is attained, opening the door to the use of paper as a reliable substrate to fabricate inorganic PV cells for a plethora of indoor applications with tremendous impact in multi-sectorial fields such as food, pharmacy and security. [ABSTRACT FROM AUTHOR]

We have characterized the structure and electrical properties of p-type nanocrystalline silicon films prepared by radio-frequency plasma-enhanced chemical vapor deposition and explored optimization methods of such layers for potential applications in thin-film solar cells. Particular attention was paid to the characterization of very thin (&#876420 nm) films. The cross-sectional morphology of the layers was studied by fitting the ellipsometry spectra using a multilayer model. The results suggest that the crystallization process in a high-pressure growth regime is mostly realized through a subsurface mechanism in the absence of the incubation layer at the substrate-film interface. Hydrogen plasma treatment of a 22-nm-thick film improved its electrical properties (conductivity increased more than ten times) owing to hydrogen insertion and Si structure rearrangements throughout the entire thickness of the film. [ABSTRACT FROM AUTHOR]

In this paper, we investigate the optoelectronic properties and the photodegradation of amorphous silicon films produced by the hot wire plasma assisted technique (HWPA-CVD). We observed that hydrogen dilution in the gas phase plays an important role in the time dependence of the photoconductivity, which is correlated with an enhancement of defect density. We also compare the degradation of these films with those produced by plasma enhanced and by hot wire chemical vapour deposition techniques (PECVD and HW-CVD) and we found lower time dependence for the photodegradation of the films produced by HWPA-CVD technique [Copyright &y& Elsevier]

Acute myeloid leukemia (AML) is the most common form of acute leukemia in adults and associated with poor prognosis. Unfortunately, most of the patients that achieve clinical complete remission after the treatment will ultimately relapse due to the persistence of minimal residual disease (MRD), that is not measurable using conventional technologies in the clinic. Microfluidics is a potential tool to improve the diagnosis by providing early detection of MRD. Herein, different designs of microfluidic devices were developed to promote lateral and vertical mixing of cells in microchannels to increase the contact area of the cells of interest with the inner surface of the device. Possible interactions between the cells and the surface were studied using fluid simulations. For the isolation of leukemic blasts, a positive selection strategy was used, targeting the cells of interest using a panel of specific biomarkers expressed in immature and aberrant blasts. Finally, once the optimisation was complete, the best conditions were used to process patient samples for downstream analysis and benchmarking, including phenotypic and genetic characterisation. The potential of these microfluidic devices to isolate and detect AML blasts may be exploited for the monitoring of AML patients at different stages of the disease. [ABSTRACT FROM AUTHOR]

Acute myeloid leukemia (AML) is the most common form of acute leukemia in adults and associated with poor prognosis. Unfortunately, most of the patients that achieve clinical complete remission after the treatment will ultimately relapse due to the persistence of minimal residual disease (MRD), that is not measurable using conventional technologies in the clinic. Microfluidics is a potential tool to improve the diagnosis by providing early detection of MRD. Herein, different designs of microfluidic devices were developed to promote lateral and vertical mixing of cells in microchannels to increase the contact area of the cells of interest with the inner surface of the device. Possible interactions between the cells and the surface were studied using fluid simulations. For the isolation of leukemic blasts, a positive selection strategy was used, targeting the cells of interest using a panel of specific biomarkers expressed in immature and aberrant blasts. Finally, once the optimisation was complete, the best conditions were used to process patient samples for downstream analysis and benchmarking, including phenotypic and genetic characterisation. The potential of these microfluidic devices to isolate and detect AML blasts may be exploited for the monitoring of AML patients at different stages of the disease. [ABSTRACT FROM AUTHOR]

Since ancient times, the use of high-tin bronze alloys (>17 wt.%) has been mainly limited to the production of specific objects such as mirrors and bells. High-tin bronzes can show distinctive colour reflection, as well as mechanical properties and corrosion resistance that clearly distinguish them from the classical bronze composition (with 8–12 wt.% tin). In the present study samples of archaeological high-tin bronze bells were studied by optical microscopy, SEM-EDX, and Raman imaging with the aim of characterising their microstructural long-term corrosion patterns. Results show the presence of high quantities of δ phase, when compared to the classical bronze composition, which makes some corrosion structures more visible in these alloys. The corrosion morphologies show selective corrosion of different metal phases along depth of corrosion, which were attributed to different oxygen potentials. This study proposes a classification of four types of corrosion structures occurring in two-phase bronzes as a consequence of aeration conditions during burial time and aeration within the corrosion structure. [ABSTRACT FROM AUTHOR]

• Cement as a material used in the historical reconstructions of the Palace of Knossos. • Identification of the types of salts and crusts by WDXRF, XRD, FTIR and μ-Raman. • Formation of gypsum crusts and thenardite efflorescence resulting from the deterioration process of the cements. • Importance of material characterisation for the conservation of monuments. The Palace of Knossos, located on the island of Crete, Greece, is one of Europe's most important archaeological sites, serving as a testament to the Minoan civilization. Situated near the Mediterranean Sea, it is in close proximity to the seaport, airport, and industrial areas. Decay products commonly found in historical monuments within or near urban areas, such as black crusts and salt efflorescence, are also prevalent at the Palace of Knossos. To better understand the characteristics of the type of deterioration compounds found on cement in historical reconstruction zones, as well as their possible relationship with factors influencing the deterioration process, a multi-analytical approach was designed for the study of these materials. The results indicate that the black crusts primarily consist of gypsum and carbonaceous matter. However, the efflorescence salts are predominantly composed of thenardite instead of halite, despite the palace's proximity to the coastal area. These results may contribute to ongoing and future maintenance and preservation efforts for the monument. [ABSTRACT FROM AUTHOR]

Early and accurate detection of infection by pathogenic microorganisms, such as Plasmodium, the causative agent of malaria, is critical for clinical diagnosis and ultimately determines the patient's outcome. We have combined a polystyrene-based microfluidic device with an immunoassay which utilises Surface-Enhanced Raman Spectroscopy (SERS) to detect malaria. The method can be easily translated to a point-of-care testing format and shows excellent sensitivity and specificity, when compared to the gold standard for laboratorial detection of Plasmodium infections. The device can be fabricated in less than 30 min by direct patterning on shrinkable polystyrene sheets of adaptable three-dimensional microfluidic chips. To validate the microfluidic system, samples of P. falciparum-infected red blood cell cultures were used. The SERS-based immunoassay enabled the detection of 0.0012 ± 0.0001% parasitaemia in a P. falciparum-infected red blood cell culture supernatant, an ∼7-fold higher sensitivity than that attained by most rapid diagnostic tests. Our approach successfully overcomes the main challenges of the current Plasmodium detection methods, including increased reproducibility, sensitivity, and specificity. Furthermore, our system can be easily adapted for detection of other pathogens and has excellent properties for early diagnosis of infectious diseases, a decisive step towards lowering their high burden on healthcare systems worldwide. [ABSTRACT FROM AUTHOR]

Advanced light management via front‐coated photonic nanostructures is a promising strategy to enhance photovoltaic (PV) efficiency through wave‐optical light‐trapping (LT) effects, avoiding the conventional texturing processes that induce the degradation of electrical performance due to increased carrier recombination. Titanium dioxide (TiO2) honeycomb arrays with different geometry are engineered through a highly‐scalable colloidal lithography method on flat crystalline silicon (c‐Si) wafers and tested on standard planar c‐Si interdigitated back‐contact solar cells (pIBCSCs). The photonic‐structured wafers achieve an optical photocurrent of 36.6 mA cm−2, mainly due to a broad anti‐reflection effect from the 693 nm thick nanostructured coatings. In contrast, the pIBCSC test devices reach 14% efficiency with 679 nm thick TiO2 nanostructures, corresponding to a ≈30% efficiency gain relative to uncoated pIBCSCs. In addition, several designed structures show unmatched angular acceptance enhancements in efficiency (up to 63% gain) and photocurrent density (up to 68% gain). The high‐performing (yet electrically harmless) LT scheme, here presented, entails an up‐and‐coming alternative to conventional texturing for c‐Si technological improvement that can be straightforwardly integrated into the established PV industry. [ABSTRACT FROM AUTHOR]

Droplet-based microfluidic technology is a powerful tool for generating large numbers of monodispersed nanoliter-sized droplets for ultra-high throughput screening of molecules or single cells. Yet further progress in the development of methods for the real-time detection and measurement of passing droplets is needed for achieving fully automated systems and ultimately scalability. Existing droplet monitoring technologies are either difficult to implement by non-experts or require complex experimentation setups. Moreover, commercially available monitoring equipment is expensive and therefore limited to a few laboratories worldwide. In this work, we validated for the first time an easy-to-use, open-source Bonsai visual programming language to accurately measure in real-time droplets generated in a microfluidic device. With this method, droplets are found and characterized from bright-field images with high processing speed. We used off-the-shelf components to achieve an optical system that allows sensitive image-based, label-free, and cost-effective monitoring. As a test of its use we present the results, in terms of droplet radius, circulation speed and production frequency, of our method and compared its performance with that of the widely-used ImageJ software. Moreover, we show that similar results are obtained regardless of the degree of expertise. Finally, our goal is to provide a robust, simple to integrate, and user-friendly tool for monitoring droplets, capable of helping researchers to get started in the laboratory immediately, even without programming experience, enabling analysis and reporting of droplet data in real-time and closed-loop experiments. [ABSTRACT FROM AUTHOR]

Microfluidic-based platforms have become a hallmark for chemical and biological assays, empowering micro- and nano-reaction vessels. The fusion of microfluidic technologies (digital microfluidics, continuous-flow microfluidics, and droplet microfluidics, just to name a few) presents great potential for overcoming the inherent limitations of each approach, while also elevating their respective strengths. This work exploits the combination of digital microfluidics (DMF) and droplet microfluidics (DrMF) on a single substrate, where DMF enables droplet mixing and further acts as a controlled liquid supplier for a high-throughput nano-liter droplet generator. Droplet generation is performed at a flow-focusing region, operating on dual pressure: negative pressure applied to the aqueous phase and positive pressure applied to the oil phase. We evaluate the droplets produced with our hybrid DMF–DrMF devices in terms of droplet volume, speed, and production frequency and further compare them with standalone DrMF devices. Both types of devices enable customizable droplet production (various volumes and circulation speeds), yet hybrid DMF–DrMF devices yield more controlled droplet production while achieving throughputs that are similar to standalone DrMF devices. These hybrid devices enable the production of up to four droplets per second, which reach a maximum circulation speed close to 1540 µm/s and volumes as low as 0.5 nL. [ABSTRACT FROM AUTHOR]

Digital microfluidics (DMF) arises as the next step in the fast-evolving field of operation platforms for molecular diagnostics. Moreover, isothermal schemes, such as loop-mediated isothermal amplification (LAMP), allow for further simplification of amplification protocols. Integrating DMF with LAMP will be at the core of a new generation of detection devices for effective molecular diagnostics at point-of-care (POC), providing simple, fast, and automated nucleic acid amplification with exceptional integration capabilities. Here, we demonstrate for the first time the role of coupling DMF and LAMP, in a dedicated device that allows straightforward mixing of LAMP reagents and target DNA, as well as optimum temperature control (reaction droplets undergo a temperature variation of just 0.3 °C, for 65 °C at the bottom plate). This device is produced using low-temperature and low-cost production processes, adaptable to disposable and flexible substrates. DMF-LAMP is performed with enhanced sensitivity without compromising reaction efficacy or losing reliability and efficiency, by LAMP-amplifying 0.5 ng/μL of target DNA in just 45 min. Moreover, on-chip LAMP was performed in 1.5 μL, a considerably lower volume than standard bench-top reactions. [ABSTRACT FROM AUTHOR]

The present contribution aims to enhance solar cells' performance via the development of advanced luminescent down-shifting based on encapsulated nanostructured perovskite materials. Here, thin films of inorganic lead halide (CsPbBr3) perovskite nanocrystal luminophores were synthetized, by hot-injection, deposited on glass substrates by spin-coating, and encapsulated with parylene type C, via chemical vapor deposition, to protect and stabilize the films. The optical properties of these thin films were characterized by absorption, emission and 2D contour spectra, their structure by X-ray diffraction and X-ray photoelectron spectroscopy, and the morphology by Scanning Transmission Electron microscopy. I–V curve and spectral response nanocrystalline silicon photovoltaic (nc-Si:H PV) cells were studied in the absence and presence of the perovskite and parylene luminescent down-shifting layers. The incorporation of the CsPbBr3 nanocrystals and their encapsulation with the parylene type C polymeric coating led to an increase in the current generated and the spectral response of the PV cells in the regime of the nanocrystals' fluorescence emission. A 3.1% increase in the short circuit current density and a 5.6% increase in the power conversion efficiency were observed. [ABSTRACT FROM AUTHOR]

The inexorable increase of energy demand and the efficiency bottleneck of monocrystalline silicon solar cell technology is promoting the research and development of alternative photovoltaic materials. Copper-arsenic-sulfide (CAS) compounds are still rather unexplored in the literature, yet they have been regarded as promising candidates for use as p-type absorber in solar cells, owing to their broad raw material availability, suitable bandgap and high absorption coefficient. Here, a comprehensive study is presented on the structural and optoelectronic properties of CAS thin-films deposited via radio-frequency magnetron co-sputtering, using a commercial Cu target together with a Cu-As-S target with material obtained from local resources, specifically from mines in the Portuguese region of the Iberian Pyrite Belt. Raman and X-ray diffraction analysis confirm that the use of two targets results in films with pronounced stoichiometry gradients, suggesting a transition from amorphous CAS compounds to crystalline djurleite (Cu31S16), with the increasing proximity to the Cu target. Resistivity values from 4.7 mΩ·cm to 17.4 Ω·cm are obtained, being the lowest resistive films, those with pronounced sub-bandgap free-carrier absorption. The bandgap values range from 2.20 to 2.65 eV, indicating promising application as wide-bandgap semiconductors in third-generation (e.g., multi-junction) photovoltaic devices. [ABSTRACT FROM AUTHOR]

Abstract: Soda-lime glasses doped with Eu3+ were synthesized using a variety of compositions, namely changing the fraction of CaO or Eu2O3. Those glasses were characterized with several techniques, including ellipsometry, UV–vis–NIR absorption spectroscopy, steady-state photoluminescence spectroscopy and time-resolved luminescence. The compositions' effects on optical properties such as refraction indexes, Eu3+ oscillator strengths and luminescence lifetimes were accessed from the analysis of the experimental results. Judd–Ofelt theory was used to analyze all these aspects, which allow the detection of a mismatch of optical properties from absorption and emission spectroscopy. This mismatch was confirmed from the time-resolved data, showing the existence of two different spectroscopic Eu3+ species. From those results it is concluded that there is evidence for lanthanide aggregation, giving rise to self-quenching effects that may be described through resonance energy transfer mechanisms. The difference between luminescence lifetimes for isolated and aggregated Eu(III) is interpreted as due to different interactions with oxygen in the matrix, namely degree of covalency of the Eu–O bond and point group symmetry of the lanthanide. [Copyright &y& Elsevier]

This work describes the fabrication and characterization of an improved version of large area (5 mm×80 mm with an active length of 70 mm) flexible position sensitive detectors deposited onto polymeric substrates (polyimide–Kapton® VN). The new configuration presented by the sensor is based on a heterostructure of a-Si:H/ZnO:Al. The sensors were characterized by spectral response, photocurrent dependence as a function of light intensity and position detection measurements. The set of data obtained on one-dimensional position sensitive detectors based on the heterostructure show excellent performances with a maximum spectral response of 0.12 A/W at 500 nm and a non-linearity of ±10% over 70 mm length. The produced sensors present a non-linearity higher than those ones produced on glass substrates, due to the different thermal coefficients exhibited by the polymer and the amorphous silicon film. In order to prove this behaviour, it was measured the defect density obtained by the constant photocurrent method on amorphous silicon deposited on polymeric substrates bended with different radius of curvature. [Copyright &y& Elsevier]

One of the most promising approaches to produce industrial-compatible Transparent Conducting Materials (TCMs) with excellent characteristics is the fabrication of TCO/metal/TCO multilayers. In this article, we report on the electro-optical properties of a novel high-performing TCO/metal/TCO structure in which the intra-layer is a micro-structured metallic grid instead of a continuous thin film. The grid is obtained by evaporation of Ag through a mask of polystyrene colloidal micro-spheres deposited by the Langmuir-Blodgett method and partially dry-etched in plasma. IZO/Ag grid/IZO structures with different thicknesses and mesh dimensions have been fabricated, exhibiting excellent electrical characteristics (sheet resistance below 10 Ω/□) and particularly high optical transmittance in the near-infrared spectral region as compared to planar (unstructured) TCM multilayers. Numerical simulations were also used to highlight the role of the Ag mesh parameters on the electrical properties. • High-performing micro-structured Transparent Conductive Materials (TCMs) composed of IZO/Ag Mesh/IZO ultra-thin multi-layers. • Low cost, highly-scalable, easy and no thermal budget method of deposition. • High conductivity and NIR transparency of the TCMs make them attractive for bifacial and multi-terminal tandem solar cells. [ABSTRACT FROM AUTHOR]

Highlights • New method to form highly reproducible plasmonic surfaces in an fast way by RTA process. • Influence of the annealing temperature ramp-up rate on the morphology of the nanoparticles. • Formation of arrays of Ag NP via dewetting processes in just ten minutes. • Influence of the AZO spacer layers thickness on the resulting LT effects produced by the PBRs. • Best performing PBR: 120 nm Ag/100 nm AZO/6 nm Ag NPs/60 nm AZO. • μ c-Si:H solar cells show an overall 11% improvement on device efficiency. Abstract A fast method is presented to fabricate plasmonic light trapping structures in just ten minutes (>5 × faster than the present state of art), with excellent light scattering properties. The structures are composed of silver nanoparticles (Ag NPs) deposited by thermal evaporation and self-assembled using a rapid thermal annealing (RTA) system. The effect of the RTA heating rate on the NPs production reveals to be crucial to the decrease of the annealing process. The Ag NPs are integrated in thin film silicon solar cells to form a plasmonic back reflector (PBR) that causes a diffused light reflectivity in the near-infrared (600–1100 nm wavelength region). In this configuration the thicknesses of the AZO spacer/passivating layers between NPs and rear mirror, and between NPs and silicon layer, play critical roles in the near-field coupling of the reflected light towards the solar cell absorber, which is investigated in this work. The best spacer thicknesses were found to be 100 and 60 nm, respectively, for Ag NPs with preferential sizes of about 200 nm. The microcrystalline silicon (μc-Si:H) solar cells deposited on such improved PBR demonstrate an overall 11% improvement on device efficiency, corresponding to a photocurrent of 24.4 mA/cm2 and an efficiency of 6.78%, against 21.79 mA/cm2 and 6.12%, respectively, obtained on flat structures without NPs. [ABSTRACT FROM AUTHOR]

In the present study, zinc oxide (ZnO) nanorods (NRs) with a hexagonal structure have been synthesized via a hydrothermal method assisted by microwave radiation, using specialized cardboard materials as substrates. Cardboard-type substrates are cost-efficient and robust paper-based platforms that can be integrated into several opto-electronic applications for medical diagnostics, analysis and/or quality control devices. This class of substrates also enables highly-sensitive Raman molecular detection, amiable to several different operational environments and target surfaces. The structural characterization of the ZnO NR arrays has been carried out by X-ray diffraction (XRD), scanning electron microscopy (SEM) and optical measurements. The effects of the synthesis time (5-30 min) and temperature (70-130 °C) of the ZnO NR arrays decorated with silver nanoparticles (AgNPs) have been investigated in view of their application for surface-enhanced Raman scattering (SERS) molecular detection. The size and density of the ZnO NRs, as well as those of the AgNPs, are shown to play a central role in the final SERS response. A Raman enhancement factor of 7 x 105 was obtained using rhodamine 6 G (R6G) as the test analyte; a ZnO NR array was produced for only 5 min at 70 °C. This condition presents higher ZnO NR and AgNP densities, thereby increasing the total number of plasmonic "hot-spots", their volume coverage and the number of analyte molecules that are subject to enhanced sensing. [ABSTRACT FROM AUTHOR]

Ultrasonic spray pyrolysis deposition of ZnO-based materials offers an attractive high-throughput low-cost route towards industrial production of high-quality transparent conductive oxide (TCO) thin-films. In this work, undoped and aluminium-doped ZnO films have been grown employing ultrasonic spray pyrolysis at relatively low-temperate (300 °C), followed by a post-annealing treatment. The role of Al concentration in the starting solution, as well as the rapid thermal annealing (RTA) atmosphere, were investigated and correlated to the morphological, structural, electrical and optical properties of the films. The remarkable enhancement of electrical conductivity attained here is mainly ascribed to the combined effects of: (1) homogenous incorporation of Al 3+ into the ZnO matrix, which enhances crystal quality providing higher electronic mobility; and (2) the RTA which releases the localized electrons caused by oxygen absorption and thereby increases the free carrier density. Under optimum deposition conditions, a low resistivity and a high optical transmittance around 4 × 10 −3 Ω cm and 87%, respectively, were obtained. The application of the RTA post-process after low temperature growth has several advantages relative to the direct growth at high temperature (usually 400–575 °C), such as shorter growth time and lower cost associated to the spray pyrolysis equipment requirements and usage. The results suggest that the electrical and optical properties of the ZnO:Al films can be further improved for solar cell applications by controlling the temperature of the post-deposition annealing in reducing atmosphere. [ABSTRACT FROM AUTHOR]

Digital Microfluidics (DMF) has emerged as a disruptive methodology for the control and manipulation of low volume droplets. In DMF, each droplet acts as a single reactor, which allows for extensive multiparallelization of biological and chemical reactions at a much smaller scale. DMF devices open entirely new and promising pathways for multiplex analysis and reaction occurring in a miniaturized format, thus allowing for healthcare decentralization from major laboratories to point-of-care with accurate, robust and inexpensive molecular diagnostics. Here, we shall focus on DMF platforms specifically designed for nucleic acid amplification, which is key for molecular diagnostics of several diseases and conditions, from pathogen identification to cancer mutations detection. Particular attention will be given to the device architecture, materials and nucleic acid amplification applications in validated settings. [ABSTRACT FROM AUTHOR]

The growing interest in exploring thin film technologies to produce low cost devices such as n - i - p silicon solar cells, with outstanding performances and capability to address the highly relevant energy market, turns the optimization of their fabrication process a key area of development. The usual one-dimensional analysis of the involved parameters makes it difficult and time consuming to find the optimal set of conditions. To overcome these difficulties, the combination of experimental design and statistical analysis provides the tools to explore in a multidimensional fashion the interactions between fabrication parameters and expected experimental outputs. Design of Experiment and Multivariate Analysis are demonstrated here for the optimization of: (1) the low temperature deposition (150 °C) of high quality intrinsic amorphous silicon ( i -a-Si:H); and (2) the matching of the n -, i -, and p -silicon layers thickness to maximize the efficiency of thin film solar cells. The multiple regression method applied, validated through analysis of variance and evaluated against exact numerical simulations, is shown to predict the overall intrinsic layer properties and the devices performance. The results confirm that experimental design and statistical data analysis are effective approaches to improve, within a minimum time frame and high certainty, the properties of silicon thin films, and subsequently the layer structure of solar cells. [ABSTRACT FROM AUTHOR]

The post-deposition modification of ZnO-based transparent conductive oxides (TCOs) can be the key to produce thin films with optoelectronic properties similar to indium tin oxide (ITO), but at a much lower cost. Here, we present electro-optical results achieved for post-deposition annealing of Al-Zn-O (AZO), AZO:H, Ga-Zn-O:H (GZO:H), and Zn-O:H (ZNO:H) thin films deposited by RF sputtering at room temperature. These studies comprise results of thermal annealing at atmospheric pressure, vacuum, forming gas, H2 and Ar atmospheres, and H2 and Ar plasmas, which lead to significant enhancement of their electro-optical properties, which are correlated to morphological and structural improvements. The post-deposition annealing leads to an enhancement in resistivity above 40% for AZO, AZO:H, and GZO:H, reaching ρ ≈ 2.6-3.5 × 10−4 Ωcm, while ZnO:H showed a lower improvement of 13%. The averaged optical transmittance in the visible region is about 89% for the investigated TCOs. Such results match the properties of state-of-art ITO ( ρ ≈ 10−4 Ωcm and transmittance in VIS range of 90%) employing much more earth-abundant materials. [ABSTRACT FROM AUTHOR]

The p/i interface plays a major role in the conversion efficiency of nanocrystalline silicon (nc-Si:H) solar cells. Under plasma-enhanced chemical vapor deposition (PECVD) of the intrinsic (i) nc-Si:H layer, ion bombardment can severely affect the underlying p-doped layer and degrade the solar cell performance. The core of the present work is to investigate the effect of light and heavy ion bombardment on the structural modifications of the p-layer during the p/i interface formation. The properties of the nc-Si:H materials deposited under distinct conditions are analyzed and correlated to the deposition rate and the resulting cell efficiency. To recreate the ion bombardment during the initial stages of the i-layer deposition on the p-layer, hydrogen plasma treatment was performed for 30 s (light ion bombardment), after which a flux of silane was introduced into the deposition chamber in order to initiate the heavy ion bombardment and growth of an ultra-thin (5 nm) i-layer. The structural changes of the p-type nc-Si:H layers were observed by spectroscopic ellipsometry. The obtained results confirm that detrimental structural modifications (e.g. partial amorphization of the sub-surface region and bulk) occur in the p-layer, caused by the ion bombardment. To minimize this effect, a protective buffer layer is investigated able to improve the performance of the solar cells fabricated under increased growth rate conditions. [ABSTRACT FROM AUTHOR]

Abstract: We have projected and fabricated a microfluidic platform for DNA sensing that makes use of an optical colorimetric detection method based on gold nanoparticles. The platform was fabricated using replica moulding technology in PDMS patterned by high-aspect-ratio SU-8 moulds. Biochips of various geometries were tested and evaluated in order to find out the most efficient architecture, and the rational for design, microfabrication and detection performance is presented. The best biochip configuration has been successfully applied to the DNA detection of Mycobacterium tuberculosis using only 3µl on DNA solution (i.e. 90ng of target DNA), therefore a 20-fold reduction of reagents volume is obtained when compared with the actual state of the art. [Copyright &y& Elsevier]

We report the effect of a disperse carbon interlayer between the n-a-Si:H layer and an aluminium zinc oxide (AZO) back contact on the performance of amorphous silicon solar cells. Carbon was incorporated to the AZO film as revealed by x-ray photoelectron spectroscopy and energy-dispersive x-ray analysis. Solar cells fabricated on glass substrates using AZO in the back contact performed better when a disperse carbon interlayer was present in their structure. They exhibited an initial efficiency of 11%, open-circuit voltage Voc = 1.6 V, short-circuit current JSC = 11 mA cm−2 and a filling factor of 63%, that is, a 10% increase in the JSC and 20% increase in the efficiency compared to a standard solar cell. [ABSTRACT FROM AUTHOR]

The study of building materials constituting cultural heritage is fundamental to understand their characteristics and predict their behavior. When considering materials from archaeological sites, their characterization can provide not only relevant information for a broader understanding of the site and its importance and significance but can also increase knowledge about ancient materials and their performance. The Palace of Knossos is a very important archaeological site in the European history context, and its preservation benefits from the characterization of the constituent materials. Samples of mortars from this monument were collected under the scope of the H2020 HERACLES project, where a multi-analytical approach was chosen using established protocols for the different sample typologies. Instrumental techniques such as optical microscopy (OM), X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), and simultaneous thermogravimetry and differential thermal analysis (TG–DTA) were used for the chemical, mineralogical, and morphological characterization of these mortar samples. The results indicate that the majority are lime mortars, both aerial and hydraulic, but gypsum-based mortars were also identified. Differences in the chemical composition of the samples in distinct areas of the monument allowed us to reflect on the variety of materials used in the construction of the Palace of Knossos. [ABSTRACT FROM AUTHOR]

In this paper, we present the preliminary results concerning the deposition of highly transparent and conductive gallium-doped zinc oxide (GZO) deposited on transparent flexible substrate based on cellulose derivatives. Prior to the deposition of the GZO film, the surface of the polymer have been coated with a thin silicon dioxide (SiO2) layer deposited by thermal evaporation assisted by an electron gun. By doing this surface treatment, we succeeded in depositing highly conductive and transparent GZO with an electrical resistivity of 2.0×10−3 Ω cm and an average optical transmittance in the visible part of the spectrum (400–700 nm) of 70% by r.f. magnetron sputtering at room temperature. Besides the optoelectronic properties, the films are mechanically stable with a polycrystalline structure with a strong preferred (002) orientation, parallel to the substrate. [Copyright &y& Elsevier]

In this paper, we present results concerning the thickness dependence (from 70 to 890 nm) of electrical, structural, morphological and optical properties presented by gallium-doped zinc oxide (GZO) deposited on polyethylene naphthalate (PEN) substrates by r.f. magnetron sputtering at room temperature. For thicknesses higher than 300 nm an independent correlation between the electrical, morphological, structural and optical properties are observed. The lowest resistivity obtained was 5×10−4 Ω cm with a sheet resistance of 15 Ω/□ and an average optical transmittance in the visible part of the spectra of 80%. It is also shown that by passivating the surface of the polymer by depositing a thin silicon dioxide layer the electrical and structural properties of the films are improved nearly by a factor of two. [Copyright &y& Elsevier]

Gallium-doped zinc oxide films were prepared by r.f. magnetron sputtering at room temperature as a function of the substrate–target distance. The best results were obtained for a distance of 10 cm, where a resistivity as low as 2.7×10−4 Ω cm, a Hall mobility of 18 cm2/Vs and a carrier concentration of 1.3×1021 cm−3 were achieved. The films are polycrystalline presenting a strong crystallographic c-axis orientation (002) perpendicular to the substrate. The films present an overall transmittance in the visible part of the spectra of approximately 85%, on average. [Copyright &y& Elsevier]

The pursuit of ever-more efficient, reliable, and affordable solar cells has pushed the development of nano/micro-technological solutions capable of boosting photovoltaic (PV) performance without significantly increasing costs. One of the most relevant solutions is based on light management via photonic wavelength-sized structures, as these enable pronounced efficiency improvements by reducing reflection and by trapping the light inside the devices. Furthermore, optimized microstructured coatings allow self-cleaning functionality via effective water repulsion, which reduces the accumulation of dust and particles that cause shading. Nevertheless, when it comes to market deployment, nano/micro-patterning strategies can only find application in the PV industry if their integration does not require high additional costs or delays in high-throughput solar cell manufacturing. As such, colloidal lithography (CL) is considered the preferential structuring method for PV, as it is an inexpensive and highly scalable soft-patterning technique allowing nanoscopic precision over indefinitely large areas. Tuning specific parameters, such as the size of colloids, shape, monodispersity, and final arrangement, CL enables the production of various templates/masks for different purposes and applications. This review intends to compile several recent high-profile works on this subject and how they can influence the future of solar electricity. [ABSTRACT FROM AUTHOR]

The degradation of organic pollutants in wastewaters assisted by oxide semiconductor nanostructures has been the focus of many research groups over the last decades, along with the synthesis of these nanomaterials by simple, eco-friendly, fast, and cost-effective processes. In this work, porous zinc oxide (ZnO) nanostructures were successfully synthesized via a microwave hydrothermal process. A layered zinc hydroxide carbonate (LZHC) precursor was obtained after 15 min of synthesis and submitted to different calcination temperatures to convert it into porous ZnO nanostructures. The influence of the calcination temperature (300, 500, and 700 °C) on the morphological, structural, and optical properties of the ZnO nanostructureswas investigated. All ZnO samples were tested as photocatalysts in the degradation of rhodamine B (RhB) under UV irradiation and natural sunlight. All samples showed enhanced photocatalytic activity under both light sources, with RhB being practically degraded within 60 min in both situations. The porous ZnO obtained at 700 °C showed the greatest photocatalytic activity due to its high crystallinity, with a degradation rate of 0.091 and 0.084 min−1 for UV light and sunlight, respectively. These results are a very important step towards the use of oxide semiconductors in the degradation of water pollutants mediated by natural sunlight. [ABSTRACT FROM AUTHOR]

Due to its properties, paper represents an alternative to perform point-of-care tests for colorimetric determination of glucose levels, providing simple, rapid, and inexpensive means of diagnosis. In this work, we report the development of a novel, rapid, disposable, inexpensive, enzyme-free, and colorimetric paper-based assay for glucose level determination. This sensing strategy is based on the synthesis of gold nanoparticles (AuNPs) by reduction of a gold salt precursor, in which glucose acts simultaneously as reducing and capping agent. This leads to a direct measurement of glucose without any enzymes or depending on the detection of intermediate products as in conventional enzymatic colorimetric methods. Firstly, we modelled the synthesis reaction of AuNPs to determine the optical, morphological, and kinetic properties and their manipulation for glucose sensing, by determining the influence of each of the reaction precursors towards the produced AuNPs, providing a guide for the manipulation of nucleation and growth. The adaptation of this synthesis into the developed paper platform was tested and calibrated using different standard solutions with physiological concentrations of glucose. The response of the colorimetric signals obtained with this paper-based platform showed a linear behavior until 20 mM, required for glycemic control in diabetes, using the Red × Value/Grey feature combination as a calibration metric, to describe the variations in color intensity and hue in the spot test zone. The colorimetric sensor revealed a detection limit of 0.65 mM, depending on calibration metric and sensitivity of 0.013 AU/mM for a linear sensitivity range from 1.25 to 20 mM, with high specificity for the determination of glucose in complex standards with other common reducing interferents and human serum. [ABSTRACT FROM AUTHOR]

Electronic skin (e-skin), which is an electronic surrogate of human skin, aims to recreate the multifunctionality of skin by using sensing units to detect multiple stimuli, while keeping key features of skin such as low thickness, stretchability, flexibility, and conformability. One of the most important stimuli to be detected is pressure due to its relevance in a plethora of applications, from health monitoring to functional prosthesis, robotics, and human-machine-interfaces (HMI). The performance of these e-skin pressure sensors is tailored, typically through micro-structuring techniques (such as photolithography, unconventional molds, incorporation of naturally micro-structured materials, laser engraving, amongst others) to achieve high sensitivities (commonly above 1 kPa−1), which is mostly relevant for health monitoring applications, or to extend the linearity of the behavior over a larger pressure range (from few Pa to 100 kPa), an important feature for functional prosthesis. Hence, this review intends to give a generalized view over the most relevant highlights in the development and micro-structuring of e-skin pressure sensors, while contributing to update the field with the most recent research. A special emphasis is devoted to the most employed pressure transduction mechanisms, namely capacitance, piezoelectricity, piezoresistivity, and triboelectricity, as well as to materials and novel techniques more recently explored to innovate the field and bring it a step closer to general adoption by society. [ABSTRACT FROM AUTHOR]

Microfluidic (MF) advancements have been leveraged toward the development of state-of-the-art platforms for molecular diagnostics, where isothermal amplification schemes allow for further simplification of DNA detection and quantification protocols. The MF integration with loop-mediated isothermal amplification (LAMP) is today the focus of a new generation of chip-based devices for molecular detection, aiming at fast and automated nucleic acid analysis. Here, we combined MF with droplet digital LAMP (ddLAMP) on an all-in-one device that allows for droplet generation, target amplification, and absolute quantification. This multilayer 3D chip was developed in less than 30 minutes by using a low-cost and extremely adaptable production process that exploits direct laser writing technology in "Shrinky-dinks" polystyrene sheets. ddLAMP and target quantification were performed directly on-chip, showing a high correlation between target concentration and positive droplet score. We validated this integrated chip via the amplification of targets ranging from five to 500,000 copies/reaction. Furthermore, on-chip amplification was performed in a 10 µL volume, attaining a limit of detection of five copies/µL under 60 min. This technology was applied to quantify a cancer biomarker, c-MYC, but it can be further extended to any other disease biomarker. [ABSTRACT FROM AUTHOR]

Throughout the last decade, the expansion of food testing has been gradually moving towards ordinary high throughput screening methods performed on-site. The demand for point-of-care testing, able to distinguish molecular signatures with high accuracy, sensitivity and specificity has been significantly increasing. This new requirement relies on the on-site detection and monitorization of molecular signatures suitable for the surveillance of food production and processing. The widespread use of antibiotics has contributed to disease control of livestock but has also created problems for the dairy industry and consumers. Its therapeutic and subtherapeutic use has increased the risk of contamination in milk in enough concentrations to cause economic losses to the dairy industry and have a health impact in highly sensitive individuals. This study focuses on the development of a simple Surface-Enhanced Raman Spectroscopy (SERS) method for fast high throughput screening of tetracycline (TET) in milk. For this, we integrate a paper-based low-cost, fully recyclable and highly stable SERS platform, with a minimal sample preparation protocol. A two-microliter sample of milk solutions spiked with TET (from 0.01 to 1000 ppm) is dried on a silver nanoparticle coated cardboard substrate and measured via a Raman spectrophotometer. The SERS substrate showed to be extremely stable with a shelf life of several months. A global spectrum principal component analysis approach was used to test all the detected vibrational modes and their correlation with TET concentration. Peak intensity ratios (455 cm−1/1280 cm−1 and 874 cm−1/1397 cm−1) were found to be correlated with TET concentrations in milk, achieving a sensitivity as low as 0.1 ppm. Results indicate that this SERS method combined with portable Raman spectrometer is a potential tool that can be used on-site for the monitoring of TET residues and other antibiotics. [ABSTRACT FROM AUTHOR]

Immunoassays using Surface-Enhanced Raman Spectroscopy are especially interesting on account not only of their increased sensitivity, but also due to its easy translation to point-of-care formats. The bases for these assays are bioconjugates of polyclonal antibodies and anisotropic gold nanoparticles functionalized with a Raman reporter. These bioconjugates, once loaded with the antigen analyte, can react on a sandwich format with the same antibodies immobilized on a surface. This surface can then be used for detection, on a microfluidics or immunochromatographic platform. Here, we have assembled bioconjugates of gold nanostars functionalized with 4-mercaptobenzoic acid, and anti-horseradish peroxidase antibodies. The assembly was by simple incubation, and agarose gel electrophoresis determined a high gold nanostar to antibody binding constant. The functionality of the bioconjugates is easy to determine since the respective antigen presents peroxidase enzymatic activity. Furthermore, the chosen antibody is a generic immunoglobulin G (IgG) antibody, opening the application of these principles to other antibody-antigen systems. Surface-Enhanced Raman Spectroscopy analysis of these bioconjugates indicated antigen detection down to 50 µU of peroxidase activity. All steps of conjugation were fully characterized by ultraviolet-visible spectroscopy, dynamic light scattering, ζ -Potential, scanning electron microscopy, and agarose gel electrophoresis. Based on the latter technique, a proof-of-concept was established for the proposed immunoassay. [ABSTRACT FROM AUTHOR]

Electronic skin (e-skin) is pursued as a key component in robotics and prosthesis to confer them sensing properties that mimic human skin. For pressure monitoring, a great emphasis on piezoresistive sensors was registered due to the simplicity of sensor design and readout mechanism. For higher sensitivity, films composing these sensors may be micro-structured, usually by expensive photolithography techniques or low-cost and low-customizable molds. Sensors commonly present different sensitivities in different pressure ranges, which should be avoided in robotics and prosthesis applications. The combination of pressure sensing and temperature is also relevant for the field and has room for improvement. This work proposes an alternative approach for film micro-structuration based on the production of highly customizable and low-cost molds through laser engraving. These bimodal e-skin piezoresistive and temperature sensors could achieve a stable sensitivity of −6.4 × 10−3 kPa−1 from 1.6 kPa to 100 kPa, with a very robust and reproducible performance over 27,500 cycles of objects grasping and releasing and an exceptionally high temperature coefficient of resistance (TCR) of 8.3%/°C. These results point toward the versatility and high benefit/cost ratio of the laser engraving technique to produce sensors with a suitable performance for robotics and functional prosthesis. [ABSTRACT FROM AUTHOR]