Search

Proso millet is a nutritious, sustainable, and gluten free food which is currently underutilized. They can be incorporated into the grain industry and provide much needed healthy alternatives. Efficient grinding method should be adopted for easy incorporation. This study aimed to investigate the effect of three different methods of grinding namely, roller milling (RM), pin milling (PM), and hammer milling (HM) on proso millet flour rheology and baking properties for food application. The milling flow sheet was developed toward the production of the quality whole grain flour. The particle size distribution of all the flours showed bi‐modal distribution except for the RM flour. The PM produced the flour with the finest particles with geometric mean diameter of 82 μm. The study also revealed that starch damage in the PM flour (4.64%) was higher than RM (2.46%) and HM flour (2.51%). The nutritional composition was not significantly affected by different grinding methods. Pasting properties of the flour were also affected by the grinding method applied. Rapid Visco Analysis profile showed pin mill flour to have a higher peak viscosity (PV) (2,295 cP) compared to HM (2,065 cP) and RM flour (2,130 cP). Finally, this study demonstrated that the production of bread from proso millet flour with desirable quality and texture is possible. The grinding method did not affect the specific volume of bread loaves and C‐cell characteristics. The specific volume of the breads ranged from 2.40 to 2.52 cm3/g. This study will help in promoting and producing value‐added proso millet food products with enhanced nutritional quality. [ABSTRACT FROM AUTHOR]

The study investigated the effects of acidic water (sodium bisulfate, SBS/lactic acid, LA) tempering (alone) and in combination with heat treatment on the Shiga toxin‐producing Escherichia coli (STEC) O121 and O26 load of wheat and its impact on wheat flour quality. The results of the study showed that tempering wheat with acidic water (5 and 10% wt/vol) alone reduced its STEC load by 2.0 and 2.6 log CFU/g, respectively (p ≤.05) after 24 hr of treatment. Heat treatment (55°C) significantly reduced the STEC load below detection limit (<1.6 log CFU/g) after 12 hr of treatment. The hurdle approach (5% acidic water + heat, 55°C) reduced the STEC load below detection limit within 6 hr of treatment. Finally, the wheat flours produced using the hurdle approach had lower pH (5.77–5.97) compared with the control without negatively affecting the baking and milling characteristics. Practical applications: The study demonstrated that the hurdle approach of acidic water tempering coupled with heat treatment significantly reduce the Shiga toxin‐producing Escherichia coli load of wheat without negatively impacting the wheat flour quality. Therefore, the combination of acidic water and heat treatment used in this study can be used as an antimicrobial intervention for improving the quality and safety of wheat‐milled products. [ABSTRACT FROM AUTHOR]

Increasing teff (Eragrostis tef) consumption has been recorded in recent years due to its gluten‐free nature and exceptional nutritional composition. Studies on the particle level that relates to processing and handling of teff flour are limited. The effect of different milling methods (roller mill, pin mill, and hammer mill) on size distribution, shape characteristics, and flowability of teff flour was evaluated. Physical properties (angle of repose, tapped and bulk densities, size distribution, and shape characteristics) and proximate composition were investigated and correlated with flow properties. Flowability was measured in terms of bulk, shear, and dynamic flow properties using the FT4 powder rheometer. Particle size distribution significantly (p <.05) influenced the angle of repose, aeration energy, and wall friction angle while shape characteristics (circularity and aspect ratio) significantly (p <.05) affected the aerated and tapped bulk densities and basic flow energy. Hammer‐milled flour had the highest aerated (548.00 kg/m3) and tapped bulk densities (804.33 kg/m3). Pin‐milled flour had the highest compressibility index (38.46%), Hausner ratio (1.62), angle of repose (71.57°), and wall friction angle (25.92° at 3 kPa) indicating poorer flowability. Stability index and specific energy did not vary significantly (p >.05) among the milled flours. Highest basic flow (1,191.03 mJ) and aerated energies (272.32 mJ) were required to induce flow in hammer‐milled flour due to greater proportion of large particles. Based on the flow function, all flours fall under the "easy flowing" category, but the pin‐milled flour exhibited the poorest flowability. [ABSTRACT FROM AUTHOR]

The demand for food production has been constantly increasing due to rising population. In developed countries, for example, the emergence of regional production of old grains that are rarely utilized, along with the production of commonly consumed grains, has gained importance in recent years. These grains, known collectively as ancient or heirloom grains, have offered both farmers and consumers novel ways of cultivation and products with interesting taste, characteristics and nutritional value. Among the 30 000 plant species known, only five cereals currently provide more than 50% of the world's energy intake – bread wheat (Triticum aestivum), rice (Oryza sativa), sorghum (Sorghum bicolor), millets (Panicum sp.) and maize (Zea mays). The excessive utilization of these selected species has a great potential to cause genetic losses and difficulty in bridging future agricultural demands. Teff (Eragrostis tef), an ancient grain extensively cultivated in countries like Eritrea and Ethiopia, provides promising alternatives for new food uses since its nutritional value is significantly higher than most others cereal grains. The absence of gluten allows flexibility in food utilization since it can be directly substituted to gluten‐containing products. The grain also offers an excellent balance of essential amino acids and minerals, which can fulfil the recommended daily intake and eliminates the need for fortification and enrichment. This review provides a general overview of the physical properties and nutritional composition of teff grains related to processing and applications in the food and feed industries. The current status of teff utilization, as well as the challenges in production and commercialization, and future opportunities is presented and discussed. [ABSTRACT FROM AUTHOR]

BACKGROUND Size-based fractionation of flour particles is an important process in wheat milling. Inter-particle cohesion could affect the dynamic separation process and result in loss in throughput. This study quantifies the effect of particle properties that includes physical and chemical characteristics on the shear flow behavior of wheat flour. RESULTS The cohesion and flow function values of wheat flour at three moisture contents (10%, 12%, and 14%), three particle sizes (75-106, 45-75, and <45 µm) and three sifter loads (0.5, 1.0, and 1.0 kPa) were significantly different ( P < 0.05). The triggering moisture content and particle size where the flowability shifts from 'easy flowing' to 'very cohesive' were found to be 12% (wet basis) and 45 µm, respectively. CONCLUSION The high correlation observed between the chemical composition (damaged starch, protein, and fat) on the physical (bulk and tapped densities) and flow properties (cohesion, flow function, and angle of internal friction) demonstrates that chemical composition significantly contributes towards the differences in dynamic flowability of wheat flours. In addition, fat composition had a significant effect on the differences in flowability of wheat flours due to the increased inter-particulate cohesion. © 2016 Society of Chemical Industry [ABSTRACT FROM AUTHOR]

Flow difficulties during handling, storage, and processing are common in cereal grain-based powder industries. The many studies that focus on the flow properties of powders can be classified as flow indicators, shear properties, and dynamic flow properties. The non-uniformity of physical and chemical characteristics of the individual particles that make up the bulk solid of cereal grain-based powders adds complexity to the characterization of flow behavior. Even so, knowledge of flow behavior is critical to the design of productive and cost-effective equipment for handling and processing of these powders. Because many factors influence flow, a single property/index value may not satisfactorily quantify the flow or no-flow of powders. For powders of biological origin, chemical composition and environmental factors such as temperature and relative humidity complicate flow characterization. This review focuses on the specific flow characteristics that directly affect powder flow during handling, processing, and storage. © 2015 Society of Chemical Industry [ABSTRACT FROM AUTHOR]

AbstractWheat-based foods has emerged as another potential vehicle for foodborne illness in humans. The recent occurrence of recalls involving wheat-based foods requires a full understanding of how these pathogens thrive in these food products and developing potential intervention strategies to address pathogen contamination. This manuscript is the second of a two-part review covering the status of the food safety of wheat-based products. In this manuscript, available information on the survival of enteric foodborne pathogens, food safety issues, and potential pathogen reduction steps on wheat-based foods were reviewed. Shiga toxin-producing E. coli and Salmonella are capable of surviving in wheat flours and grains for extended periods (≤ 2 years). Based on the food safety issues linked to wheat flour, the main enteric pathogens of concern are STEC (O157, O121, O26, and O103) and Salmonella. Diverse interventions such as tempering treatments, thermal treatments, and non-thermal technologies all effectively reduced the pathogenic loads of wheat grains and wheat flours (2 to 6 log CFU/g reduction). Addressing pathogen contamination of wheat-based foods is a major concern for the milling industry. Future studies could be focused on improving pathogen reduction performance and validating their effects against diverse product and process conditions. [ABSTRACT FROM AUTHOR]

AbstractThe number of food safety issues linked to wheat milled products have increased in the past decade. These incidents were mainly caused by the contamination of wheat-based products by enteric pathogens. This manuscript is the first of a two-part review on the status of the food safety of wheat-based products. This manuscript focused on reviewing the available information on the potential pre-harvest and post-harvest sources of microbial contamination, and potential foodborne pathogens present in wheat-based products. Potential pre-harvest sources of microbial contamination in wheat included animal activity, water, soil, and manure. Improper grain storage practices, pest activity, and improperly cleaned and sanitized equipment are potential sources of post-harvest microbial contamination for wheat-based foods. Raw wheat flour products and flour-based products are potentially contaminated with enteric pathogens such as Shiga toxin-producing E. coli (STECs), and Salmonella at low concentrations. Wheat grains and their derived products (i.e., flours) are potential vehicles for foodborne illness in humans due to the presence of enteric pathogens. A more holistic approach is needed for assuring the food safety of wheat-based products in the farm-to-table continuum. Future developments in the wheat supply chain should also be aimed at addressing this emerging food safety threat. [ABSTRACT FROM AUTHOR]