Search

The drive for cost reduction has led to the use of CMOS technology in the implementation of highly integrated radios. This paper presents a single-chip 5-GHz fully integrated direct conversion transceiver for IEEE 802.11a WLAN systems, manufactured in 0.18-µm CMOS. The IC features an innovative system architecture which takes advantage of the computing resources of the digital companion chip in order to eliminate I/Q mismatch and achieve accurately matched baseband filters. The integrated voltage-controlled oscillator and synthesizer achieve an integrated phase noise of less than 0.8° rms. The receiver has an overall noise figure of 5.2 dB and achieves sensitivity of -75 dBm at 54-Mb/s operation, both referred to the IC input. The transmit error vector magnitude is -33 dB at -5-dBm output power from the integrated power-amplifier driver amplifier. The transceiver occupies an area of 18.5 mm². [ABSTRACT FROM AUTHOR]

The article discusses various reports published within the issue, including one by B.K. Ahuja, H. Vu, C.A. Laber and W.H. Owen about the application of the floating gate device as a voltage reference.

This article demonstrates a scalable, time-division multiplexed biopotential recording front-end capable of real-time differential- and common-mode artifact suppression. A delta-encoded recording architecture exploits the power spectral density (PSD) characteristics of Electrocorticography (ECoG) recordings, combining an 8-bit ADC, and an 8-bit DAC to achieve 14 bits of dynamic range. The flexibility of the digital feedback architecture is leveraged to time-division multiplex 64 differential input channels onto a shared mixed-signal front-end, reducing channel area by 2x compared to the state-of-the-art. The feedback DAC used for delta-encoding also serves to cancel differential artifacts with an off-chip adaptive loop. Analysis of this architecture and measured silicon performance of a 65 nm CMOS test-chip implementation, both on the bench and in-vivo, are included with this paper.

A current-mode interface chip for Silicon Photomultiplier (SiPM) array based positron emission tomography (PET) imaging front-ends is described. The circuit uses a high-speed current amplifier with a low input impedance, to minimize signal loss at the SiPM amplifier interface. To reduce the impact of dark noise, a novel high-speed threshold detection/comparator circuit is used to remove unwanted noise events. A prototype chip interfaces an array of SiPMs to the digital backend of a Positron Emission Tomography (PET) system using 64 readout channels, each of which contain a current amplifier and a threshold detection component. To reduce the number of backend channels, a row-column pulse positioning architecture (RCA) has been implemented. The ASIC occupies an area of 14.04 mm 2 in 130nm STMicroelectronics HCMOS9GP process. The measured input impedance of the current amplifier is 20 ohms at 10 MHz, while the threshold detection circuit's propagation delay is 0.3-2ns.

Recent developments in the area of Positron Emission Tomography (PET) detectors using Silicon Photomultipliers (SiPMs) have demonstrated the feasibility of higher resolution PET scanners due to a significant reduction in the detector form factor. The increased detector density requires a proportionally larger number of channels to interface the SiPM array with the backend digital signal processing necessary for eventual image reconstruction. This work presents a CMOS ASIC design for signal reducing readout electronics in support of an 8×8 silicon photomultiplier array. The row/column/diagonal summation circuit significantly reduces the number of required channels, reducing the cost of subsequent digitizing electronics. Current amplifiers are used with a single input from each SiPM cathode. This approach helps to reduce the detector loading, while generating all the necessary row, column and diagonal addressing information. In addition, the single current amplifier used in our Pulse-Positioning architecture facilitates the extraction of pulse timing information. Other components under design at present include a current-mode comparator which enables threshold detection for dark noise current reduction, a transimpedance amplifier and a variable output impedance I/O driver which adapts to a wide range of loading conditions between the ASIC and lines with the off-chip Analog-to-Digital Converters (ADCs).

The recent realization of Silicon Photomultiplier (SiPM) devices as solid-state detectors for Positron Emission Tomography holds the promise of improving image resolution, integrating a significant portion of the interface electronics, and potentially lowering the power consumption. Our lab has previously reported on novel board-level readout electronics for an 8×8 silicon photomultiplier (SiPM) array featuring row/column summation technique to reduce the hardware requirements for signal processing and is currently working on taking the next step by implementing a monolithic CMOS chip which is based on the row-column architecture. To date, relatively little modeling has been done to understand the impact of analog non-idealities associated with the front-end electronics, on SiPM-based PET systems. This paper focuses on various analog impairments associated with PET scanner readout electronics. Matlab was used as a simulation platform to model the noise, linearity and signal bandwidth of the frontend electronics with the measured SiPM pulses as the input.

Our lab has previously reported on novel board-level readout electronics for an 8×8 silicon photomultiplier (SiPM) array featuring row/column summation technique to reduce the hardware requirements for signal processing. We are taking the next step by implementing a monolithic CMOS chip which is based on the row-column architecture. In addition, this paper explores the option of using diagonal summation as well as calibration to compensate for temperature and process variations. Further description of a timing pickoff signal which aligns all of the positioning (spatial channels) pulses in the array is described. The ASIC design is targeted to be scalable with the detector size and flexible to accommodate detectors from different vendors. This paper focuses on circuit implementation issues associated with the design of the ASIC to interface our Phase II MiCES FPGA board with a SiPM array. Moreover, a discussion is provided for strategies to eventually integrate all the analog and mixed-signal electronics with the SiPM, on either a single-silicon substrate or multi-chip module (MCM).