Search

A surface streamer is a ubiquitous discharge in electric equipment and surface dielectric barrier discharge. It is expected to suppress this kind of surface discharge in the insulation system, but on the other hand, the surface streamer is also utilized for the generation of active ions and the control of a gas kinetic distribution. As a product of the surface streamer, surface charge influences and characterizes the streamer's behavior. This study observed the two-dimensional transient evolution of the surface charge and the tangential electric field in a single individual surface streamer at the nanosecond level. Using a reflective Pockels effect system and a framing camera system, the surface streamer propagation under a sub-microsecond pulse voltage was measured in real time and in situ. The inception, propagation, and deceleration of a surface streamer are observed. The measurement exhibits an electrode-charge equipotential region that equivalently extends the electrode boundary. Under an anode field with a weak tangential component, the interior of the surface streamer channel exhibits local deviations from the quasi-neutrality, and a reversed tangential electric field is observed. The lateral movement of the positive charge may be responsible for this reverse electric field. The diagnostic technique presented in this study can describe the surface charge transient behavior in pulsed surface discharges, which complements the streamer model.

Epoxy with high healability and high insulating properties is demonstrated to heal from electrical damage through fluorine-substituted carbamate bonds. With attractive degradability, it performs as a green dielectric and enables component recycling.

As one of the most sustainable, efficient, and cleanest ways for hydrogen production, electrochemical water splitting relies heavily on cost-efficient and stable electrocatalysts. Herein, a self-supported and nitrogen-doped hybrid CoP/Ni2P was synthesized through a simple two-step hydrothermal process followed by low-temperature phosphorization and nitridation (N-CoP/Ni2P@NF). Both experimental and density functional theory calculation results suggest that nitrogen doping can tune the electrical structure of the CoP/Ni2P heterostructure and thus optimize the free energy of adsorbed H on the surface of N-CoP/Ni2P@NF and accelerate the electronic transport activity. The prepared N-CoP/Ni2P@NF exhibits excellent electrocatalytic hydrogen evolution reaction (HER) performance, which merely requires an overpotential of -46 mV at -10 mA cm-2 and shows a negligible decay after a long durability test for 72 h in alkaline (1.0 M KOH) media. Consequently, this work supplies a novel strategy with great potential for designing transition metal phosphate-based catalysts with high HER performance.

High-performance multifunctional materials for water splitting driven by low voltage are crucial for hydrogen evolution reaction (HER), but developing such materials is challenging. Herein, a simple strategy was designed to build a MoS2/Co9S8/MoC@CNT-N (MCM@CNT-N) heterostructure with a large number of interfaces. Regarding the HER, the synthesized MCM@CNT-N heterostructure catalyst showed high efficiency and stable electrocatalytic performance, with a low overpotential of 174.2 mV and a small Tafel slope of 84.7 mV dec−1 at a current density of 10 mA cm−2 in 0.5 M H2SO4. In addition to the function of heterojunctions, the excellent activity is also attributed to the introduction of Co and N atoms and the formation of carbon nanotubes. This work provides a new approach to build efficient and low-cost electrocatalysts for electrochemical reactions.

Molybdenum disulfide (MoS2) is intrinsically inert for the hydrogen evolution reaction (HER) in alkaline media due to its electronic structures. Herein, we tune the electronic structures of MoS2 by a combined strategy of post-N doping coupled with the synergistic effect of Ti3C2TX. The as-prepared N-doped MoS2/Ti3C2TX heterostructures show remarkable alkaline HER activity with an overpotential of 225 mV at 140 mA cm-2, which ranks the N-doped MoS2/Ti3C2TX heterostructures among the best MoS2/MXene-based electrocatalysts reported for alkaline HER. The first-principles calculations indicate that the N doping can enhance the activation of nearby S sites of MoS2/Ti3C2TX and thus promote the HER process. This strategy provides a promising way to develop high-efficiency MoS2/MXene heterostructure catalysts for alkaline HER.

In this report, a pulsed electro-acoustic (PEA) device is modified to test the charge profile in epoxy resin at 77 K (-196°C) and successfully obtains the charge signal. A piezoelectric material suitable for cryogenic application is chosen for the measurement. In the experiment, the polarization and depolarization tests are operated with different voltage supply procedures. After initial wave recovery, the waveforms are discernable enough to identify the charge information. It is found that the charges are much less active at the low temperature with both slow dissipating rate and low injection quantity, comparing to the case at 293 K.

It still is a challenge to create a superior and easily coupled bifunctional electrocatalyst for water splitting impelled by a low voltage. In this work, the controlled growth of Co2P NAs on the surface of a MXene (Ti3C2Tx)-modified self-supporting electrode is demonstrated as a competent and reliable bifunctional electrocatalyst for efficient water splitting. The heterointerface in Co2P@Ti3C2Tx with an optimized adsorption free energy of H*, H2O, and better conductivity can give enhanced HER (hydrogen evolution reaction) activity, with a low overpotential (42 mV) at 10 mA cm-2. Additionally, the OER (oxygen evolution reaction) activity has also been similarly strengthened by the synergy of Co2P and MXene with an overpotential of 267 mV to arrive at 10 mA cm-2. Furthermore, the excellent bifunctional electrode (Co2P@Ti3C2Tx∥Co2P@Ti3C2Tx) exhibits efficient engineering water-splitting performance (1.46 V@10 mA cm-2) in alkaline solution. This simple design can propose a promising approach to exploit precious-metal-free catalysts for energy conversion.

The development of a system to measure simultaneously the current and space charge in a dielectric is described. The results obtained for low density polyethylene samples show that the relationship between space charge accumulation and the time-dependent current is not straightforward. In accord with previous work on space charge limited currents, the transient currents initially decreased, but after a while an increment or peak appeared. Additionally, the generation and extraction of space charge packets caused an impulse-like current peak such as previously observed. By comparing the electric field and current at the anode, it was found that the increment and the peak of the anode current are determined by injected negative carriers reaching the anode rather than the increase of electric field at the anode. It is shown that the dynamical evolution of the current can be divided into three stages similar to transient space charge limited current theory.

As an interface between the different insulating polymers exists in the joints of High Voltage Direct Current (HVDC) cables, the differences in the field-and-temperature dependence of the conductivities of the materials is regarded as a problem leading to interface charge accumulation and field distortion. In this report, using blocking materials to prevent charge injection from one or both sides of the electrodes, the contributions of charge injection and ionization in low-density polyethylene (LDPE), cross-linked polyethylene with nanoparticles (nano-XLPE) and ethylene propylene diene monomer (EPDM) are distinguished and evaluated based on the results from pulsed electro-acoustic (PEA) method. It is found that the contributions of charge injection and ionization behave differently in different materials. The mechanism behind the field-and-temperature dependences of the conductivities of the three materials is explained successfully. This study helps to clarify the charge transfer mechanism, and thus supports the quantitative calculation of the space charge and electric field distribution in cable joints.

Preparation of high-activity and earth-abundant bifunctional catalysts for efficient electrochemical water splitting are crucial and challenging. Herein, Co-doped Ni3N nanosheets loaded on nickel foam (Co-Ni3N) were synthesized. The as-prepared Co-Ni3N exhibits excellent catalytic activity toward both the hydrogen evolution reaction (HER) and the oxygen evolution reaction (OER) in alkaline media. Density functional theory (DFT) calculation reveals that Co-Ni3N with redistribution of electrons not only can facilitate the HER kinetics but also can regulate intermediates adsorption energies for OER. Specifically, the Co-Ni3N exhibits high efficiency and stable catalytic activity, with an overpotential of only 30 and 270 mV at a current density of 10 mA cm-2 for the HER and OER in 1 M KOH, respectively. This work provides strong evidence to the merit of Co doping to improve the innate electrochemical performance in bifunctional catalysts, which might have a common impact in many similar metal-metal nitride electrocatalysts.

This paper proposes a method of distinguishing the contributions of ionized and injected charges to the charge transport in oil immersed paper in triple-layer and double-layer samples. With the double-layer sample, the apparent mobility including the ions contribution is obtained by the calculation according to the speed of accumulated charge density at the interface. The contribution of ions is excluded by subtracting the accumulated charge density in the triple-layer sample from that in the double-layer sample. It is found that the interface charge mainly comes from the ionization charges under a low field, and the contribution of injected charge takes a more important part at higher electric field.

Developing highly efficient non-precious electrocatalytic materials for H2 production in an alkaline medium is attractive on the front of green energy production. Herein, we successfully designed an electrocatalyst with superb hydrophilicity, high conductivity, and a kinetically beneficial structure using Ni2P/MXene over a 3D Ni foam (NF) for the alkaline hydrogen evolution reaction (HER) based on the laboratory and computational research works. The designed self-supported and highly effective electrocatalyst achieves a huge boost in the HER activity compared with that of pristine Ni2P nanosheets owing to the distinctive structure and synergy of coupling Ti3C2Tx and Ni2P. More specifically, Ni2P/Ti3C2Tx/NF produces an electric current density of 10 mA·cm-2 under a low overpotential (135 mV) and shows excellent durability under alkaline (1 M KOH) conditions, and the observed performance degradation is negligible. The outstanding HER activity makes the synthetic strategy of Ni2P/Ti3C2Tx/NF a potential approach to be extended to other transition-metal-based electrocatalysts for enhanced catalytic performance.

Residual charges produced in previous partial discharges (PDs) are considered as one aspect of memory effects that affect subsequent discharge behavior. In this paper, we review past studies about memory effects induced by residual charges during successive PDs. At first, surface charge dynamics for cavity and needle-to-dielectric discharges are presented. Subsequently, three methods used to unravel the memory effects are described, e.g. conditional distribution, pulse sequence analysis (PSA) and chopped PD (CPD). Then effects of residual charges on PD inception, discharge propagation and collective behavior are summarized. In addition, contributions of residual charges to the transitions between discharge modes and discharge patterns are presented. At last, some problems relevant to the memory effects are discussed, followed by suggestions for future work.

The effect of yttrium on the reaction of tungsten oxide with CO was studied for the preparing various morphologies and size of tungsten carbide. The reaction rate, phase composition, particles size and morphology, surface area of samples were studied by TG (thermogravimetry), XRD (X-ray diffraction), SEM (scanning electron microscopy) and BET (Brunauer–Emmett–Teller), respectively. It was found that the reaction route was following WO3 → W18O49 → WO2 → WC at lower temperature, while at higher temperature, an intermediate phase W was formed and then carbonized to WC. During the reaction of pure WO3 or mixtures (1 wt.% Y(NO3)3 + WO3) with CO at lower temperature, the final products almost maintained the large irregular block shape. With the increase of temperature, the large WC particles were degraded and the obtained sub-particles became much more dispersed. After the addition of yttrium nitrate, the rod-like sub-particles were transformed into more stable polyhedral-shaped sub-particles with a smaller size. Furthermore, the mechanism of effect of yttrium on prepared tungsten carbides were analyzed in detail.

In this research, the equivalence of space charge for coaxial cables and plane samples are analyzed through simulation. Bipolar charge transport models of coaxial cables and plane samples are established with the same material-dependent parameters, the bulk charge and total space charge distributions are simulated and comparatively researched under isothermal and temperature gradient conditions. The presented results indicate that the space charge behavior shows a basic equivalence in terms of charge variation laws and distribution. In addition, few discrepancies in the heterocharge amount and charge waveform amplitude are observed and mainly ascribed to the sample geometry, mobility gradient distribution and the spatial resolution of the measuring system, respectively. Investigations of space charge characteristics with a plane pulsed electro-acoustic measurement system may be accepted as a practice for providing the space charge characteristics of coaxial cable insulation, unless it is necessary to investigate the cable space charge distribution under actual operating conditions.

Epoxy resin is widely deployed as a high voltage electrical insulation material when compounded with inorganic fillers. However, in the laboratory, the filler prevents visual observation of the long-term degradation known as electrical treeing. To date therefore, much laboratory testing has been conducted on unrepresentative unfilled materials. Here, the impact of micro-sized fillers on the treeing phenomenon in an epoxy system has been explored. Sub-micrometre resolution 3D reconstructions of electrical trees are reported from X-ray computed tomography (XCT) using an advanced ‘pink beam’ synchrotron light source imaging system. The role of filler particles between 1 and 10 μm in size on tree channel propagation is reported. In highly filled materials (30% by weight) a radical change in tree growth behavior is seen, leading to bush tree rather than branch tree growth. The dielectric breakdown time at constant stress was also found to increase as the square root of the filler level. The change in geometry of tree growth may explain the extended life of filled materials in high voltage applications.

Electrical trees are widely grown in laboratories from metallic needle electrodes to enable the degradation process to proceed rapidly at voltages of ∼10 kV AC. Here it is shown that cone-shaped air gaps may form at a needle tip, even when they are not visible optically. Using X-ray imaging techniques, samples with and without air gaps up to 55 μm long have been characterized. The presence of air gaps led to partial discharge (PD) patterns resembling void-discharges. Prior to tree initiation, discharge characteristics evolved with increased voltage increments and increased phase lag behind the applied voltage. These changes to PD characteristics reflect a change in the physical state of the air gap. Although samples with air gaps generally initiated trees quicker than those with no gap, PD activities did not appear to play a decisive role in tree initiation times. However, initial voids were found to have major impact on the subsequent tree growth. In samples with persistent pre-tree air-gap PDs, trees grew larger branchy structures with higher PD magnitudes. In addition, the PDs became more asymmetric between positive and negative half-cycles than occurred in samples with no air gaps. It is shown that understanding the interface between the needle and polymer at a micron scale is critical to interpretation of laboratory tree growth experiments.

This paper reports observations of electrical tree growth by X-ray computed tomography (XCT) in multiple steps. Growth between times of observation has been obtained by subtraction of an image from the subsequent one. Partial discharge (PD) signals were also recorded during tree growth. It is determined that not all PDs support tree extension. By comparing the energy released by PD and the vaporization energy of newly grown tree channels, it is found that only the PDs that reach the tree tips can contribute to the growth of tree length. In such cases, the efficiency of energy conversion was very high, whereas PD resulting in increases in tree channel diameter had a much lower conversion efficiency. Nano XCT images reveal many finer branches along the trunk of the main tree and in the front of the main channel tree tips. It seems that those finer branches led to tree growth, but were not directly associated with local PD. The new imaging techniques have shown great value in resolving the relationship between partial discharge activity and electrical tree growth, providing a platform for deeper understanding of the tree growth process, and interpretation of partial discharge measurements.

The mobility of positive and negative charge carriers has been separately measured independently of carrier concentration in low-density polyethylene (LDPE) and its nanocomposites using space charge measurements in a bilayer system. It was found that the carrier mobility of positive charge carriers was larger than that of negative charge carriers for both LDPE and its nanocomposites and that the carrier mobility was one to two orders of magnitude less in the nanocomposite than unfilled LDPE under the same conditions. The mobility is interpreted in terms of a field-assisted hopping model whose estimated activation energies were verified by measurements at different temperatures. The form of the charge traps and carrier transport is interpreted in terms of known features and electron and hole traps and the effect of nano-particles upon these features is discussed.

It still remains a great challenge to develop alternative electrocatalysts with low cost, high efficiency and good stability for the hydrogen evolution reaction (HER). In this study, effectively conductive rGO (reduced graphene oxide) was used as the support both to promote charge transfer and to refine the particle size of WC, to realize efficient and stable HER performance. The facile in situ method can make highly dispersed WC nanoparticles firmly anchor onto the rGO substrate. Benefiting from its unique morphology and strong synergistic effect, the designed WC@rGO achieves a giant improvement in HER activity in both acidic and alkaline solutions compared with pristine WC. The overpotentials of WC@rGO are 2.82 and 2.30 times smaller than those of pristine WC to achieve 10 mA cm−2 in acid and alkaline solutions. More specifically, the Pt-modified WC electrocatalyst with negligible accumulation of Pt (4 wt%) even exhibits superior electrocatalytic performance (η10 and Tafel slope of 54 mV and 21 mV dec−1 in acid solution and 61 mV and 28 mV dec−1 in alkaline solution) to commercial 10 wt% Pt@C. The method reported in this study enables eco-friendly preparation of cheap, stable and effective HER electrodes.

For the assembly of electrochromic devices (ECDs) with generally multilayer structures, supportive components usually are needed to be incorporated with EC materials. Herein, we reviewed several impressive methods to design and fabricate ECDs with high performance and versatility based on recent frontier research. The first part of the review is centered on the desirability and strengthening mechanism of nanostructured inorganic EC materials. The second part illustrates the recent advances in transparent conductors. We then summarize the demands and means to modify the formation of electrolytes for practicable ECDs. Moreover, efforts to increase the compatibility with the EC layer and ion capacity are delineated. At the end, the application prospects of inorganic ECDs are further explored, which offers a guideline for the industrialization process of ECDs.