Search

The present study investigated the impact of different loading approaches and microbial activity on the Natural Organic Matter (NOM) removal efficiency and capacity of ion exchange resins. Gaining further knowledge on the impact of loading approaches is of relevance because laboratory-scale multiple loading tests (MLTs) have been introduced as a simpler and faster alternative to column tests for predicting the performance of IEX, but only anecdotal evidence exists to support their ability to forecast contaminant removal and runtime until breakthrough of IEX systems. The overall trends observed for the removal and the time to breakthrough of organic material estimated using MLTs differed from those estimated using column tests. The results nonetheless suggest that MLTs could best be used as an effective tool to screen different ion exchange resins in terms of their ability to remove various contaminants of interest from different raw waters. The microbial activity was also observed to impact the removal and time to breakthrough. In the absence of regeneration, a microbial community rapidly established itself in ion exchange columns and contributed to the removal of organic material. Biological ion exchange (BIEX) removed more organic material and enabled operation beyond the point when the resin capacity would have otherwise been exhausted using conventional (i.e. in the absence of a microbial community) ion exchange. Furthermore, significantly greater removal of organic matter could be achieved with BIEX than biological activated carbon (BAC) (i.e. 56 ± 7% vs. 15 ± 5%, respectively) when operated at similar loading rates. The results suggest that for some raw waters, BIEX could replace BAC as the technology of choice for the removal of organic material.

The natural organic matter (NOM) removal efficiency and regeneration behavior of ion-exchange filters with promoted biological activity (BIEX) was compared to operation where biological activity was suppressed (i.e. abiotic conditions). The impact of BIEX pre-treatment on fouling in subsequent ultrafiltration was also investigated. Biological operation enhanced NOM removal by approximately 50% due to an additional degradation of smaller humic substances, building blocks and low molecular weight acids. Promotion of biological activity significantly increased the time to breakthrough of the filters and, therefore, is expected to lower the regeneration frequency as well as the amount of regenerate of which to dispose. Pre-treatment using BIEX filters resulted in a significant decrease in total and irreversible fouling during subsequent ultrafiltration. The decrease was attributed to the effective removal of medium and low molecular weight NOM fractions. The results indicate that BIEX filtration is a robust, affordable and easy-to-operate pre-treatment approach to minimize fouling in ultrafiltration systems and enhance the quality of the produced permeate.

A pilot-scale study was performed to evaluate a coagulant dose which had been optimized for biopolymer (i.e., foulant) removal on subsequent ultrafiltration (UF) fouling, as well as disinfection by-product (DBP) precursor removal. Polyaluminum chloride (PACl) dosages were selected based on a point of diminishing returns for biopolymer removal (0.5 mg/L) and directly compared to that applied at full-scale (6 mg/L). Membrane fouling (reversible and irreversible) was measured as resistance increase over a 48 hour filtration period. DBP formation potential (total trihalomethanes (TTHMs), haloacetic acids (HAA9) and total adsorbable organic halides (AOX)) were measured in both raw and treated waters. Results of the study indicate that application of a PACl dose optimized for biopolymer reduction (0.5 mg/L) resulted in 65% less irreversible UF fouling when compared to 6 mg/L. The addition of PACl prior to the membrane resulted in up to a 14% reduction in DBP precursors relative to the UF membrane alone. A similar level of DBP precursor reduction was achieved for both 0.5 and 6 mg/L dosages. The results have implications for cost savings, which may be realized due to decreased chemical use, as well as increased membrane life associated with lower irreversible fouling rates.

Surface shear stress induced by different air sparging regimes on a submerged hollow fiber ultrafiltration module with horizontally-oriented, densely packed fibers was characterized. Continuous and intermittent (cycling on and off) coarse bubbles (0.75–2.5 mL), as well as large pulse bubble (150 and 500 mL) sparging were considered for a range of air flow rates. The power required to induce surface shear stress on the surface of the hollow fibers was substantially lower when using large pulse bubble sparging compared to both continuous and intermittent coarse bubble sparging. Results indicated that the air flow required for pulse bubble sparging was more than 80% lower than that required for coarse bubble sparging to induce comparable surface shear stress (and corresponding fouling control). This study demonstrates the potential value and efficiency of pulse bubble air sparging as a fouling control option in densely packed hollow fiber membrane systems.

The effect of surface shear stress on membrane fouling during submerged hollow fiber ultrafiltration of three different surface waters (two lakes, one river) was investigated. Surface shear stresses that mimicked those induced when applying continuous and intermittent coarse bubble air sparging, large pulse bubble air sparging, as well as no air sparging were considered. The results suggest that fouling was mainly due to the accumulation of the biopolymer fraction of the natural organic matter present in the raw water. Inducing shear stresses onto the membrane surface significantly decreased the rate of membrane fouling (relative to no shear stress applied) in all waters tested. Of the shear stress conditions studied, that which mimicked large pulse bubble sparging had the greatest effect, reducing fouling by up to 80% when compared to conditions with no sparging applied. Conditions that mimicked intermittent and continuous coarse bubble fouling reduced the rate of fouling by up to 77 and 49%, respectively. These results suggest that the shear stresses induced by sparging can promote back transport of soluble organic material from the membrane surface. A semi-empirical relationship was developed to estimate the effect of raw water characteristics and applied sparging conditions on membrane fouling.